Search Documents

By D. R. Tesarik, M. K. Larson, D. K. Denton, J. B. Seymour, R. L. Rains, T. J. Williams

Because backfill has occasionally collapsed into an active working area, posing a hazard to miners, engineers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and Hecla Mining Co. installed instruments in a cemented, backfilled, stope-ramp intersection at Hecla’s Lucky Friday Mine, Mullan, ID. The purpose was to measure stress and strain changes in the backfill and reinforcing members during undercut mining. The instruments were monitored for 6 months while three successive cuts were mined below the intersection. Readings showed induced loads up to 3450 kPa (500 psi) in the backfill as stope walls converged 2.5 to 12 cm (1 to 5 in). The backfill then deformed against the top and bottom plates of the 2-m- (6-ft-) long vertical rock bolts installed as reinforcement, producing loads to 177 kN (40,000 lb)on the rock bolts. We hypothesize that a compressive zone was created in the backfill that allowed the backfill to remain stable as long as the compressive zones from adjacent rock bolts overlapped. This hypothesis is presented in graphical form. Of particular interest was the effect of loading on trusses installed to augment the vertical rock bolts and wire mesh typically installed in backfill. Data from the instruments indicate that wall closure perpendicular to the vein induced loads in truss legs parallel to the vein and in the rock bolt driven through the center of the truss, but, because they are designed to function under tension, truss legs perpendicular to the vein supplied in significant support as a result of compressional forces from wall closure. Based on this study, use of trusses was discontinued, and an alternative support system of wood beams and posts was installed as needed to ensure the safety of miners working beneath the backfill in stope-ramp intersections.

Jan 7, 2001

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. This report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems. Methane-drainage systems used in conjunction with bleederless ventilation systems are discussed. Ground control considerations such as pillar design, entry stability, and seal usage are reviewed. Monitoring systems for spontaneous combustion detection, methane-drainage control, and behind seals are examined. Finally, methods for evaluating the spontaneous combustion hazard of a mining operation to determine when the use of a bleederless ventilation system is warranted are reviewed.

Jan 1, 1994

By S. P. Howell

"Technical statistical study has been made of accidents in the anthracite region of Pennsylvania in which explosives were involved. The data have been taken from the accident reports in the files of the department of mines of Pennsylvania, supplemented by inquiries in the field.This study has disclosed a wealth of information regarding the nature and the cause of accidents that occurred where different means of firing shots of explosives were employed. In the anthracite region shots are fired with fuse, with squibs, and with electricity,Many of the salient features of this accident experience are illustrated in this report of investigations, and a number of recommendations are made to reduce the hazards of each of these three methods of shot firing.Experience seems to demonstrate that, under conditions in the anthracite region, electric firing of shots is substantially the safest method; that accidents wherein fuse is employed are more frequent than accidents in which electric firing is employed; and that the number of accidents when squibs are employed far exceeds those in which either fuse or electric firing is used."

Mar 1, 1930

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By W. L. Crentz

The Black Mesa coal field is part of the Hopi and Navajo Indian Reservation in Apache, Navajo, and Coconino Counties, Ariz. The field is in an isolated area with the nearest railroad 70 to 90 miles to the south. Travel is restricted by roads that become impassable during inclement weather. The area is a mesa and rises from 500 to 2,000 feet above the surrounding territory. Water is very scarce, and the nearest stream of any consequence is the Colorado River about 90 miles northwest from the center of the field. Coal beds are found in the Mesaverde formation of the Cretaceous age, but they are uncorrelated and range from subbituminous to bituminous in rank. Huddle2/ estimates the reserves of subbituminous coal in Arizona at about 15 billion tons, most of which is in the Black Mesa field. The geology of the field has been reported by Campbell and Gregory.3/ Coal production is small, and the output is used almost exclusively for domestic fuel in the Indian schools, missions, and trading posts.

Jan 1, 1955

By Ellsworth R. Spencer

A lightweight fiberglass feed leg for hand-held pneumatic percussion rock drills has been fabricated and tested by the Bureau of Mines. Its lighter weight facilitates easier handling of the rock drill apparatus, thereby reducing the potential for back injury to the driller and in- creasing drilling productivity. Current hand-held feed leg drills of the same class are 50 pct heavier than the Bureau-devised feed leg drill, which is comprised of a reduced-noise drill and the fiberglass feed leg. In-mine tests of the fiberglass leg showed that its performance and cost are comparable to those of standard aluminum feed legs.

Jan 1, 1985

By Seth C. Schaefer

[As part of the Bureau of Mines effort to provide thermodynamic data for advancement of mineral resources technology, the standard Gibbs energies of formation (?G°f) of MnS (manganese sulfide) and Fe0.9 S (pyrrhotite) were investigated with a high-temperature galvanic cell employing stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnS, MnO, S02 (g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt with the overall cell reaction MnS (s) + 1.5 02 (g, 0.0114 atm) = MnO (s) + S02 (g) . (1) These results give the standard Gibbs energy of formation of MnS for the reaction Mn (s) + 0.552 (g) = MnS (s) (2) ?G°f = -66.487 + 15.19 x 10-3T±0.207 kcal/mole (896.4 - 1,208.1 K) (3) where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, FeO .9S, Fe304 , S02 (g, 1 atm) //Zr02//02 (g, 0.0114 atm) , Pt with the overall cell reaction 10/3 FeO .9 S (s) + 16/3 02 (g, 0.0114 atm) = Fe.,04 (s) +10/3 S02 (g). (4) These results yield the standard Gibbs energy of formation for the reaction 0.9 Fe (s) + 0.5 S2 (g) = Fe0.9 S (s) (5) ?G°f = -35.229 + 12.67 x 1073T+-0.104 kcal/mole (839.5 - 1,086.6 K). (6) A third-law analysis of MnS data yields a standard enthalpy of formation (AH°f) for the reaction Mn (s) + S (rh) = MnS (s) (7) ?H°f298 = -51.16±0.21 kcal/mole (8) A similar third-law analysis for Fe0.9S data yields a ?29°f298 for the reaction 0.9 Fe(s) + S(rh) = FeO .9S(s) (9) ?HO\°f298 = -24.01±_0.15 kcal/mole. (10) ]

Jan 1, 1980

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to devise a procedure for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 parts per million of W03). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44 percent tungstic oxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process-development unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By Leonard Obert

A triaxial procedure is described for measuring the modulus of elasticity and Possion's ratio of stress relief cores , that is , the concentric hole cores obtained by the overcoring technique . The elastic constant determinations can be made at stress levels comparable with those encountered in underground mining . The results from tests on an aluminum alloy calibration specimen and four rock specimens are included .

Jan 1, 1964

By C. Melvin Lepper

A solid-state amplifier for the bridge circuit of an atomic-absorption mercury detector is presented and described. Operational advantages over previously used circuitry include improved time and temperature stability, increased measurement accuracy, and simplified setup, calibration, and operation.

Jan 1, 1972

By K. C. Dean

A semiquantitative test for the presence and identification of cesium and rubidium in rocks, clays, and mineral waters has been developed by the Bureau of Mines. The test can be used in the field, as a guide for the prospector, geologist, or mining engineer engaged in location or development [w]ork. It comprises two simple spot tests of a solution prepared from the [m]ineral sample. Phosphomolybdic acid, added to a drop of the test solution, [d]etects cesium, rubidium, and potassium in quantities as low as 60 parts per [m]illion. Silicomolybdic acid, added to a second drop of test solution, enables the operator to distinguish between cesium and/or rubidium and potassium. Test procedures, equipment requirements, and limitations of the method are described in this report. Cesium and rubidium were discovered in 1860 and 1861 by Bunsen and Kirchhoff with a spectroscope. The elements usually occur together, particularly in granite and granitic pegmatites. Rubidium does not occur as an essential constituent of any known mineral, yet it is found as a minor element in so many minerals that rubidium is 16th in abundance in the earth's crust. Cesium, which ranks as the 37th most abundant element, is the principal component of pollucite and a minor element in a wide variety of minerals.

Jan 1, 1960

By H. P. LeVan

The Bureau of Mines has developed a technically feasible continuous single-stage leaching and thickening system for extracting manganese from umber by a sulfuric acid-ferrous sulfate process; the cocurrent leaching and thickening system proved simpler to operate and control than the countercurrent leaching and thickening system developed earlier" Related tests investigated the use of a centrifuge to replace thickeners for separating the product liquor from are residues and compared several chemical agents for removing iron from the pregnant manganese leach solutions. Results of Some exploratory autoclaving tests are also given.

Jan 1, 1972

By C. W. Smith

The Bureau of Mines conducted laboratory-scale beneficiation tests on a sample of corundum gneiss from Montana to devise a method for beneficiating corundum for use as a substitute for refractory-grade bauxite. A flotation process utilizing petroleum sulfonate as the collector in an acid circuit was devised. Results showed that two flotation schemes each produced a concentrate exceeding the national stockpile specifications for calcined bauxite. From a feed containing 28 pct corundum concentrates containing up to 92.5 pct alumina (A1203) were produced with a corundum recovery of 78.5 pct.

Jan 1, 1987

To assist coal mine operators and regulatory agencies in selecting the most appropriate method to treat coal mine drainage utilizing expert system computer technology. The software package is called the Coal Mine Drainage Treatment PRO. Approach Experts in the field of coal mine drainage treatment were interviewed to determine their methods of assessing mine drainage treatment problems and their rationale for selecting a treatment protocol. These diagnostic, selection, and design criteria were codified in an interactive set of computer programs. Expert systems permit the user to input specific site data and receive treatment advice customized to the user's site and treatment objectives. How It Works The Coal Mine Drainage Treatment PRO package developed by the U.S. Bureau of Mines (USBM) consists of four programs or modules: (1) a control module, (2) a mine drainage treatment tutorial module, (3) a treatment advice module, and (4) a reference module (figure 1). A context-sensitive HELP Facility is also provided.

Jan 1, 1996

By Harold E. Marr

The Bureau of Mines evaluated two drill-hole probes for the delineation of Missouri lead ores. The battery-powered, portable instruments, weighing less than 30 pounds, were designed for logging holes of 1.8 inches in diameter or larger. These probes have dual scintillation detectors, balanced filters with a pass band for lead Ka radiation, and a cobalt-57 source of radiation. The results of field tests in Missouri confirm laboratory tests indicating that probe response can be correlated to lead ore grade using counting times of 10 seconds or less at any selected depth in the hole.

Jan 1, 1972

By K. C. Dean

Time and motion studies were made by the Federal Bureau of Mines on the hand and machine dismantling of scrapped auto starter motors, generators, and alternators for recovery of copper, aluminum, and iron. The studies showed that an individual with power handtools and convenient access to a hydraulic press, power bandsaw, acetylene torch, and power lathe could, in an 8-hour day, disassemble about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively, and the iron yield would be about seven times the copper weight. About 100 pounds of aluminum would be obtained from the alternators.

Jan 1, 1976

By J. A. Ruppert, P. M. Sullivan

A process was developed on a laboratory scale in which iron contained in galvanizers ' zinc dross and aluminum contained in scrap zinc die - cast alloy were removed simultaneously . Melting both types of scrap together in the proper proportions resulted in formation of solid intermetallic Fe₂ Alg , which was readily removed from the melt by filtration and centrifugation . Recovery was 87 to 92 percent of the available zinc . Refined filtrate contained 0.02 percent iron and 0.20 percent aluminum. Aluminum content was further reduced to less than 0.01 percent by fluxing with zinc chloride . Low temperatures employed and inexpensive equipment requirements make the process commercially attractive .

Jan 1, 1964

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By B. W. Naugle

This report describes the carbonizing properties of coals from the principal beds in Cambria County, Pa. Samples of coals from Upper and Lower Freeport and Upper and Lower Kittanning beds having estimated minable reserves of 50-million tons or more were studied by the Bureau of Mines. Cambria County coals rank either as medium-or low-volatile bituminous. A preparation study indicated that all coals tested in this county, except one sample from the Lower Freeport bed, were responsive to cleaning and would yield a product with satisfactory chemical properties for metallurgical coal. All coals tested from Cambria County yielded strong coke; however, they expand excessively when carbonized singly, and should be used only as minor constituents in metallurgical coking blends when carbonized in slot-type ovens.

Jan 1, 1959

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976