Search Documents

By J. E. Tiffany

Some of the gases produced by permissible explosives on detonation are poisonous, and the probable hazard involved by the inhalation of carbon monoxide in the past has been evaluated from results of tests in the Bichel Gage. Tests have now been made in the Experimental Coal Mine of the Bureau of Mines at Bruceton, Pa., to determine the composition of the gases obtained under actual mining conditions for the purpose of comparing these, results with those found by the Bichel gage tests. Two permissible explosives were procured for these tests, one that produces a relatively low quantity of poisonous gases in the Bichel gage (24.8 liters per 1-1/2 pounds of explosive) and another that produces a relatively high quantity of poisonous gases (94.6 liters per 1-1/2 pounds). The first of these is designated by the Bureau of Mines as a class A4/ explosive and the other is designated a class B explosive. In comparison with Bichel-gage tests, the shooting of permissible explosives in a coal shot hole resulted in a large reduction in the quantity of carbon monoxide, the principal poisonous gas, which; in the mine tests, was only 22 percent of that found in Bichel-gage tests: The quantity of carbon monoxide from the class B explosive in Bichel-gage tests was 3.8 times larger than that from the class A explosive; in the coalmine tests the ratio was 4:1. The concentrations of carbon monoxide in the mine tests, as determined by analysis of the atmosphere in an enclosed space resulting from shooting 1-1/2-pound and 3-pound charges of the class A explosive, were 0.03 and 0.06 percent, respectively, and the concentrations from 1-1/2-pound and 3-pound charges of the class B explosive were 0.10 and 0.24 percent.

Jan 1, 1950

By V. F. Parry, J. B. Goodman, W. S. Landers

"This investigation was conducted: under the direction of A.C. Fieldner, chief, Fuel and Explosives Branch, Bureau of Mines, Washington, D. C. The following members of a Technical .advisory Committee were helpful in advancing the investigation: L. C. Harrington, dean, College of Engineering, University of North Dakota; D. F. Pane, president, Sheridan-Wyoming Coal Co.; Carson W. Smith, president, Consolidated goal & Coke Co.; Durbin van Law, consulting, engineer, Denver & Rio Grande Western Railroad; and C. B. Carpenter, professor of metallurgy, Colorado School of Mines. Coal samples from the Northern Colorado field used in the stoker during 3 years of service were supplied through the cooperation of N. C. Brooks, secretary, Northern Colorado Coals, Inc.This report describes the development and practical tests made on a small stoker-fired system for heating service water automatically. The system was designed to take advantage of the favorable reactivity of low-rank fuels, and the objective was to devise a combination of stoker, heat-receiving, and hot-water storage system Which would be automatic for at least 30 days without attention, while heating service water at minimum cost. The system was developed to a point where coal consumption was less than 10 pounds (or less than 100,000 B.t.u.) per day. The total operating cost of hot water for an average-family-was about $1.00 per month, with coal retailing at $6.00 per ton and electric power at 4 cents a kilowatt-hour. The heating system was designed for the utilization of low-rank fuels, but the general features of the double-tank system can be 'employed fuels, either gas or liquid fuels.The Subbituminous Coal and Lignite Section of the Bureau of Mines began investigations on the utilization of low-rank fuels in domestic appliances during 1939. Tests were made on various devices to find out if they were suitable for the low-rank fuels. Most of the available appliances for burning coal have been designed for the higher-rank fuels, and they are not well-suited for burning the lower-rank coals at maximum efficiency, because subbituminous coals and lignite have high bed moisture ranging between 20 and 40 percent by weight, which lowers heating value to the range of 10,000 to 6,500 B.t.u. per pound. They are noncoking, and the ash content ranges between 4 and 6 percent, with a fusion temperature of about 2,0000 F."

Jun 1, 1946

By Gerald W. Elger

A new process under development by the U.S. Bureau of Mines for producing synthetic rutile from ilmenite is described. Rutile formation is based on oxidation and fluxing of titania slag produced by electric furnacing of ilmenite. Laboratory tests show that phosphorus pentoxide flux additions to oxidized slag enhance conversion to rutile by forming a phosphate-based glass matrix. This matrix contains most of the major impurities, including the oxides of iron, aluminum, magnesium, manganese, and silicon. Rutile crystals of 5 to 150 microns in size were formed in slags heated to temperatures of 800° to 1,550° C. The synthetic rutile crystals were liberated from ground slag by treating with phosphoric acid to weaken the glass matrix, followed by attrition scrubbing. Rutile fractions analyzed as high as 94 percent titania content. In several instances, more than 90 percent of the titanium in the shag was recovered to yield combined rutile fractions containing 90.2 to 92.6 percent titania.

Jan 1, 1971

By R. E. Kennedy

The presence of combustible gases and vapors in air can constitute n extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and. allied industries, the U. S. Bureau of Mines has investigated the explosive properties of a number of gaseous and liquid compounds; the results of these investigations have been published in various government papers and journal articles. The increased use of liquefied, petroleum gases has intensified interest in the effect of high pressures on the explosibility of propane-air mixtures. The limits of flammability of natural gas-air mixtures have been determined at pressures ranging from 50 min. Hg to 3,000 p.s.i. As it is known that a combustible. gas or vapor cannot burn or explode when the oxygen content of the atmosphere is less than a certain value, critical values were determined for the oxygen content of atmospheres to which nitrogen had been added as a diluent. In this connection limits of flammability were determined for ethane in atmospheres containing added. nitrogen or carbon dioxide at pressures up to 900 p.s.i.g.

Jan 1, 1951

By E. J. Schneider

In view of the current interest in the constituents of low-temperature tar, the Synthesis of three known xylenols and their hydroxyacetic acid derivatives has been undertaken by the U. S. Bureau of Mines. One of these xylenols, the 1,3,2 derivative first reported by Steinkopf and Höpner,4 has been described by Brown and Branting.5 The other two derivatives, the 1,3,5 first reported by Schütz6 and the 1,2,3 reported by Steinkopf and Höpner, have now been studied in greater detail. In the present work the synthesis of 1,2,3-xylenol and 1,3,5-xylenol was repeated, with some improvements in the former. The hydroxyacetic acid derivatives were also prepared, and it was found that while the melting point of the 1,2,3 derivative agreed with that of Steinkopf and Höpner. that of the 1,3,5 derivative was found to be 111° instead of 85 to 86° as reported by Schütz, by Steinkopf, and later by Bruckner. The discrepancy between the melting-point figures is doubtless due to differences in the purity of the xylenols used in the synthesis of the acids. Schütz obtained his 1,3,5 acid by recrystallizing an impure sample obtained from a mixture of xylenols. The difficulty of obtaining a pure acid by starting with a mixture is demonstrated by Bruckner, who despite painstaking efforts was unable to obtain the pure 162.5° melting 1,2,4 isomer from a mixture that persistently melted at 138° C. Steinkopf did not repeat Schütz's work but merely used the latter's figures in compiling a table. Bruckner, on the other hand. apparently also made the acid (by an improved method), and it is difficult to explain his checking Schütz's figure, unless it is that he, too used a symmetrical xylenol obtained from a tar and not prepared synthetically, as was the one reported in this paper.

Jan 1, 1929

By R. L. Grayson, W. E. Wallace, T. Simonyi, J. C. Harrison

"Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz may have different amounts of surface-availablequartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface-available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.INTRODUCTIONFrom our previous work (Grayson, 1991), we have shown that the amount of pure quartz in a respirable coal mine dust sample appears to vary directly with the rank of the seam (using fixed carbon as the basis for comparison), except when a substantial rock parting, roof or floor are mined. Our other work (Wallace et al., 1989) showed that high-silica particles in a clay mine may generally be coated with clay, rendering the quartz core non-available for surface reaction in the lung. The combination of these findings led us to hypothesize that the coating phenomenon may indeed be present in coal mines as well, and that a rank relationship may be present regarding this phenomenon. Thus higher rank coal seams may have more surface-available quartz as well as more pure quartz particles in their respirable dusts. The scientific protocol for testing this hypothesis and the results obtained to date are discussed in this paper. Thus far, there is no reason to doubt that the relationship holds."

Mar 1, 1992

By M. S. Cetiner

This report describes the prototype development If a medium to high voltage coupler, suitable for underground coal mining operations. The coupler has such unique features as automatic dust covers and continuous phase pin shielding. The coupler is rated at 7500V and 250A continuous operation.

Jan 1, 1982

By J. M. Kuchta

Experimental data are presented on the autoignition temperature (AIT) characteristics of the hydrocarbon jet fuel, JP-6, in various oxygen-nitrogen atmospheres under conditions of constant volume and constant pressure. AIT's of this fuel in air varied little with fuel injection pressure but increased greatly with decreasing fuel content at low fuel-air-ratios. They also increased with decreasing oxygen content of the fuel vapor-oxidant atmosphere. Consistent with thermal ignition theory, the ignition temperatures increased with decreasing initial pressure, ignition delay, and vessel radius; expressions are given which define the observed variation of AIT with these variables for JP-6 fuel vapor-air mixtures. The significance of autoignition temperature data obtained using various ignition criteria is discussed to show the usefulness of such data in evaluating fire and explosion hazards. In addition, data are presented on the extent of oxidation that occurs prior to autoignition of this fuel in air at various temperatures.

Jan 1, 1965

By Joan T. May

The Federal Bureau of Mines investigated the potential for recovering aluminum from copper-dump leach liquors by use of single-contact ion-exchange technology. A strongly acidic ion-exchange resin was used to extract aluminum from a typical dump leach liquor and from synthetic leach liquors. Aluminum was stripped from resin with a HS04 or NaCl solution. Bench-scale experiments indicate that a single-contact ion exchange is technically feasible, but that the process is limited by the relatively low loading capacity of the resin and the excessive amount of stripping agent required. A further limitation is that significant amounts of magnesium and iron are loaded and stripped along with the aluminum.

Jan 1, 1976

By Edward D. Thimons

A remote-actuated stench gas fire-warning system has been designed and tested by the Bureau of Mines. This system makes use of the hard-wire network for the mine's phone pager system, thus greatly reducing the system cost. By locating stench gas canisters with remote-actuation release capabilities near working sections, the fire-warning time can be greatly reduced. In a test of the system in a Missouri lead mine, the time required to warn miners of a fire at two working faces was reduced from about 20min with the conventional system to less than 4 min with the remote-actuated system.

Jan 1, 1984

By Stephen Krickovic, J. E. Carpetta, T. D. Moore

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By H. D. Pallister

A review of? reports and literature on the pyrite deposits at Pyriton, Ala., indicated that a large tonnage of pyrite, some of which contained a small amount of copper, had been mined and shipped to fertilizer plants throughout the South. The information contained in this literature tended to demonstrate that the ore occurred in separate lenses of greater or less extent and of varying thickness and richness in pyrite as well as in copper. The outcrop being parallel with the Atlantic Coastline Railroad and just south of it makes the deposits readily accessible for shipment. Slopes could be sunk as they were in the past in the ore body if it were of sufficient grade and thickness, and the ore could be hoisted up the slope and milled close to the slope mouth with an ample supply of water from Talladega Creek, which follows the outcrop closely.

Jan 1, 1949

By B. K. Shibler, I. S. Solet, H. W. St. Clair

"This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics.The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor. Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.INTRODUCTIONAlthough the United States is the world's largest consumer of tin, virtually no tin ores occur within our national borders. Most of the world's tin supply comes from alluvial deposits in the Far East and in Africa, The major sources of tin ores are Malaya, Indochina, Bolivia, Belgian Congo, Nigeria, Thailand, Burma, China, and the United Kingdom. Bolivia is the only important source of tin in the western hemisphere. It was the chief source of tin f or the United States during World War II. The Government-owned tin smelter at Texas City, Tex., was built primarily for smelting Bolivian ores and depends largely on Bolivian ores for its operation. Bolivia is the only major tin-producing country in which the tin ores occur as vein or lode deposits requiring underground mining. Most of the tin from the Far East and Africa is mined by dredges from alluvial or placer depos its. It is recovered as a high-grade concentrate of cassiterite relatively free from impurities. The tin minerals in the lode deposits are more intimately associated with other minerals and more difficult to separate into a clean concentrate. Furthermore, a large part of the tin in the original ore is lost during concentration. The ores as mined contain only a few percent of tin, so they must be milled to separate the gangue minerals and produce a concentrate containing 30 to 40 percent tin before they are shipped to the smelter. The losses of tin that occur during milling vary from 18 to 65 percent. The average recovery of tin from Bolivian ores is probably 50 to 60 percent."

Dec 1, 1954

By Austin B. Clayton

The magnetite deposits of the Big Ore Bank, in Lincoln County, N.C., were mined during the reconstruction period following the Civil War. The country rock at the Big Ore Bank property consists of micaceous schists and schistose quartzite with a few beds of dolomitic marble. Magnetite occurs with micaceous chlorite schist and is often so schistose that it is hard to distinguish from associated minerals. A magnetic survey by the North Carolina Geological Survey indicated several magnetic anomalies that appeared to justify exploration. The Bureau of Mines drilled 10 diamond-drill holes, totaling 4,493 linear feet, to delineate the deposits. More than 500 sludge samples and 119 core samples were collected for analysis. The project was begun in November 1943 and completed in April 1944.

Jan 1, 1948

By K. O. Bennington

Enthalpies of formation of three sodium titanates were determined by hydrofluoric acid solution calorimetry, The values obtained for formation from the elements at 298.15° K are -370.9±0.5 kcal/mole for Na2TiO3, -832.1±0.9 kcal/mole for Na2Ti307, and -1,510.9±1.7 kcal/mole for Na2Ti6013. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and from the component oxides for Na2Ti03 and Na2Ti307.

Jan 1, 1973

By A. W. Fahrenwald

The logic leading to the development of the experiments in this paper already has been stated in Part I,3 but is briefly as follows: The results of the batch-grind experiments in which time of "grind" and fineness of finished product were the variables, strongly indicated (1) that batch grinding involving a single grind could not be operated under any condition to give maximum mill efficiency, (2) that the, sieve analysis of the feed charge in the mill materially affected the efficiency of the mill, and (3) that the percentage of finished product in the mill is a vital factor in ball-mill efficiency. A laboratory closed-circuit grind technic designed to simulate present closed-circuit grinding suggested itself, in which: a ball mill and a classifier constitute the grinding unit. The features of the closed-circuit grinding system are: (1) Short large diameter mills, (3) rapid flow of pulp through the mill, (3) continuous automatic removal of finished product from the system, and (4) high circulating loads. The high circulating load is a result if the short length of the Mill - that is, of the time the charge remains in the mill - and the small percentage of finished material produced during each circuit of the feed through the mill.

Jan 1, 1930

By Robert Roby

The Mouat copper-nickel deposit in Stillwater County, south-central Montana, was examined by Paul T. Allsman, an engineer of the Bureau of Mines, in 1939. Because of the strategic importance of nickel, a project was executed by John East, Jr., J. J. Naughton, and E. W. Newman, engineers of the Bureau, to further delimit some of the copper-nickel sulfide-bearing bodies that had been discovered by the Anaconda Copper Mining. Co. in 1937 and to investigate the central part of the deposit, which had not been drilled previously. This report is based largely upon the results of the. Bureau of Mines investigation and the results of exploration by the Anaconda Copper Mining Co. In addition, a brief description is given of some other copper-nickel sulfide-bearing deposits along tho Stillwater Complex.

Jan 1, 1949

By A. L. Engel

This report is a compilation of preliminary and, in some cases, more extensive concentration experiments by the Federal Bureau of Mines on low-and medium-grade fluorspar ores from three localities in Nevada and one in California. The work was done on samples obtained from Shoshone mine, Nye County, Valery mine, Pershing County, and the Broken Hills mine, Mineral County, all in Nevada, and Dirty Weather mine, Inyo County, Calif. These investigations were made to aid in the development of domestic fluorspar resources, in line with the Bureau's long-established program of conservation of mineral resources. The treatment methods employed in the experimental work described included simulated or "heavy-liquid" gravity concentration of coarse minerals and comparatively fine-grained minerals, and flotation concentration of finely-ground minerals. These methods were attempted in order to beneficiate the ores and produce concentrates which could be marketed readily, with as high a recovery rate as possible, while using simple treatment methods suitable for small-scale operation.

Jan 1, 1961

By W. C. Hudson

"The Miami-West Palm Beach belt of silica sand, which may be suitable for the manufacture of high-grade glass, extends 65 miles northward from the neighborhood of Miami to the vicinity of West Palm Beach, The sand presumably originated in the host rocks constituting the oceanward slope of the Appalachian Mountains and the Piedmont Plateau of Georgia and the Carolinas. The sand now lies in a long, narrow, and probably thin belt that forms a dune-capped terrace marking a previous stage of submergence. The highest dune crests appear to be no more than 30 feet above sea level, and the water table is about 10 or 15 feet below the general level of the terrace.The width of the belt in several places is known to be more than a mile, and the thickness of the clean glass sand sampled ranged from 4 to more than 7 feet. Visual inspection and the meager data indicate the existence of bodies of glass sand large enough to supply foreseeable markets.Analyses of three samples indicate that beneficiation would make the sand suitable for the better grades of ordinary and flint glass.The prospective grade and quantity of sand, an available market in Florida for glassware, and the expectation of postwar expansion of the new industry of glass producing justify more detailed exploratory work and beneficiation testing.U. S. Route No. 1, Old Dixie Highway, the Seaboard Railway, and the Florida East Coast Railway, all substantially parallel and usually within a width of a mile or two, run along parts of the belt or between it and the coast. In addition to many streets and unpaved roads, a paved road crosses the belt at right angles about every 5 miles. Numerous towns are situated within or near the belt. Any area selected for a mining, processing, and manufacturing plant would be near a railroad, a highway, and water and also accessible to public utilities.The subtropical climate, famous for its pleasantly warm winters, would preclude seasonal interruption of plant operations."

Apr 1, 1946

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961