Search Documents

By E. J. Ostrowski, P. L. Woolf, J. P. Morris, Norwood B. Melcher

By injecting natural gas through auxiliary tuyeres into the smelting zone of the Bureau of Mines ' experimental blast furnace in January 1959 , the investigators succeeded in reducing the coke consumption by approximately one - third that of the base period . This caused a 30 - percent increase in pig iron production with no increase in wind rate . The maximum gas addition in these experiments was 4,665 cubic feet per ton of metal produced . Sharp reduction in gas consumption occurred when high hot blast and high wind rates were used , although the gas injection rate in percent of air blown remained constant . As the heat energy produced by burning natural gas to carbon monoxide and hydrogen is much less than burning coke to carbon monoxide , greater blast temperatures were required during the test runs . The gases produced from the methane were , however , more effective reductants ; so it was possible to increase the production rate while reducing the total heat requirements per ton of metal produced . During a base period with an all - sinter burden , before introduction of natural gas , a coke rate of 1,484 pounds per net ton of pig iron was attained , using an average blast temperature of 1,518 ° F. Gas was introduced gradually over a two -week period until an average 7 percent of the air blown was reached . During this period , the wind rate was adjusted downward to maintain a constant flow of gas in the bosh . The production rate of the furnace remained relatively constant . The quality of pig iron, however , improved as the sulfur load on the furnace was reduced as a result of the substitution of gas for coke . Blast temperatures were increased during this period from 1,518 ° F. to 1,939 ° F. , when the maximum gas addition was reached .

Jul 1, 1960

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By J. E. Dooley

Reference mass spectra and analytical correlations for 20 alkylcycloalkyl sulfides and two dicycloalkyl sulfides are presented 'to provide information that will facilitate the identification of sulfur compounds occurring in natural or synthetic mixtures. Reference spectra indicate relative intensities in addition to parent and base peak sensitivities. Analytical correlations establish the ionic species that reflect major fragmentation paths for the com-pounds studied. Specifically, the correlations show that base peaks are formed by several different processes: (1) Cleavage of the bond a to the ring, (2) fragmentation of the alkyl chain, and (3) fragmentation of the ring plus fragment contribution from the alkyl chain. Useful correlations for deter-mining alkyl chain length involve the CnH2+3S+ and CnH2n+1 + ions. CnH2n-2+ and CnH2n-1 S+ ions reveal the number of carbon atoms in the cyclic ring. Other important ionic species are also discussed.

Jan 1, 1970

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

By R. Havens

During investigations of the occurrence of manganese in the western United States in the early 1940?s, examining engineers of the Bureau of Mines collected samples from seven claims and mines in southern Arizona. For convenience in reporting the results, the work on the properties is grouped in three districts. As the ores were too low grade to be acceptable to producers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The San Fernando group is about 10.5 miles south of Patagonia in the Harshaw mining district. G. T. Humphries and D. Alonso held an option on the property, which was owned by H. Bender. Two samples were taken; 1 was a picked sample and the other a representative sample of ore as exposed in the mine.

Jan 1, 1954

By C. M. Mason

The methods currently used by the Bureau of Mines to evaluate the sensitivity, strength, incendivity, gaseous products, and physical properties of explosives and hazardous chemicals are described. Included are the tests used to evaluate explosives which arc certified as permissible for use in underground coal mines.

Jan 1, 1972

By B. H. Caudle, A. D. PUCKETT

This paper summarizes precent knowledge of the ignition qualities of pure hydrocarbons likely to be present in modern Diesel engine fuels, as shown by an extensive search of the technical literature. The report also discusses the possible significance of cetane number and hydrocarbon struc- ture. Cetane or cetene numbers, and other physical properties, are tabu- lated for about 100 hydrocarbons, and a bibliography is appended. In recent years the Diesel engine has enjoyed increasing popularity due to its dependability, inherent characteristics of fuel economy, and the fact that it operates on a fuel that hitherto has been available in comparatively large quantities at a low price. These qualities have en- abled the compression-ignition engine to compete very favorably with other types of prime movers in many fields and have led to predictions of fur- ther rapid expansion in the application of Diesel power. In a survey of the field of all petroleum fuels for combustion engines, Holaday et al (9) have predicted that by 1948 railroads will be using 10 times as much Diesel fuel as was used in 1939 and that over-all consumption will have doubled that of 1939. Other estimates of the yearly demand for Diesel fuels five years hence vary from 2,6 to 5 times the amount used in 1944. Into this picture has come the question of whether the greatly in- creased production to meet this estimated demand is compatible with the maintenance and possible improvement in quality of fuels necessary to satisfy future engines. Unfortunately perhaps for the Diesel engine, factors other than those of simple arithmetical multiplication must be considered. For example, the consumption of oil in central heating plants doubled from 1935 to 1943, and a further increase of 57 percent of the 1943 demand is expected by 1950. Jet propulsion has been developed to the stage where it is entirely practical for military aircraft. Catalytic cracking plants, many of which were constructed to meet the war- time accelerated demand for high-octane gasoline, are taking their place in the refining industry. All these developments, as well as the Diesel engine, require material of approximately the same boiling range. Virgin gas oils make excellent burner fuels, perform most satisfactorily in the gas-turbine units for aircraft according to present information, and are at a premium as catalytic cracking stock.

Jul 1, 1948

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129. The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.

Jan 1, 1931

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129.7 The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.8

Jan 1, 1931

By J. P. Powell

The application of secondary producing methods for recovering additional oil from known fields has been recognized for many years as important to the economy of the nation. One of the most successful secondary methods is waterflooding, which conserves our natural resources by preventing premature abandoment of stripper leases and revitalizing previously abandoned areas. Waterflooding as a secondary-recovery method was introduced into the Midcontinent region in 1931, and its use as such has become widespread. As with most new methods, the most favorable fields and leases received primary attention, whereas those with viscous oil or less favorable sand characteristics were bypassed. Numerous reports3 4 5 6/ have been published giving the results of individual waterflooding projects, In this report, attention is directed to the effect of a single factor, the viscosity of the oil produced,

Jan 1, 1959

By J. D. Brown

The electron optics, vacuum system, and sample stage assembly for the Bureau of Mines? electron probe X-ray spectrograph were purchased. Four scanning curved-crystal spectrometers, two reflection- and two transmission-type, were designed and constructed by the authors. The reflection spectrometers are placed in a vacuum chamber for measurement of long-wave-length X-radiation. Detection, pulse-amplitude discrimination, and recording circuits are provided for the simultaneous measurement of four X-ray spectral lines. Minimum spot size is approximately 2 microns in diameter at 30 kilovolts and a sample-to-ground current of 5 x 10-8 ampere. At this voltage and current the limit of detection with reflection spectrometers is less than 0.05 weight-percent for most elements. The limit of detection for elements determined by transmission-type spectrometers, evaluated at 35 kilovolts and 5 x 10-8 ampere, is approximately 0.1 weight--percent for all elements having excitation voltages below 20 kilovolts. In general, reflection spectrometers exhibited satisfactory but poorer resolution than the transmission type, resolution of the spectrometers being limited primarily by crystal imperfections, with greater mosaic structure being introduced by the grinding process for the reflection crystals. Several applications of the electron probe X-ray spectrograph are described. Analysis of a uranium-steel is discussed in detail to illustrate calculation of composition from measured X-ray intensities.

Jan 1, 1962

By John J. Sammarco

The U.S. Bureau of Mines is conducting research into computer-assisted mining, which requires investigation of new techniques for development and application of computer-based technologies. Today's technology can require significant effort in software development, as has become evident in the early stages of this Bureau research. Technologies for software automation, such as computer-aided software engineering (CASE), are available. This report explores CASE, its general features, and its importance in software development. Information is presented to assist in selection and application of the variety of CASE tools and methods for automating various stages of software development. When evaluating CASE for use, it is important to examine tools that support an organization's existing methods of software development. Support for existing hardware platforms must also be examined. Merely selecting a "good" CASE tool does not insure success. Thorough evaluation of implementing CASE is also critical. Subjects to evaluate for CASE implementation include organization culture, support from management and end users, training resources, and pilot projects. Organizations that benefit the most from CASE evaluate CASE features with respect to their needs and they properly implement CASE.

Jan 1, 1990

By Selim E. Woodworth

This paper, describing the milling practice on the Mother Lode as typified in the mill of the Argonaut Mining Co. at Jackson, Amador County, Calif., is one of a series prepared by the United States Bureau of Mines. The data herein presented and furnished through the courtesy of E. A. Stent, managing director and vice president of the Argonaut Co., covers operations from 1914 through the year 1929.

Jan 1, 1931

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931. The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results of other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time each sample was taken will also be reported.

Jan 1, 1932

By G. Esterhuizen, C. Karacan

Methane can be a significant hazard in coal mine longwalling operations and extensive methane mitigation techniques are employed by coal mine operators. Reservoir modeling techniques are used to better understand the liberation and migration of methane from the surrounding rocks towards the mine ventilation system. The caved rock behind the advancing longwall face, known as the gob, can contain high void ratios, providing high permeability flow paths to the methane. The gob is progressively compacted by the weight of the overburden, resulting in a reduction in the void ratio and associated permeability. Estimating the permeability distribution within the gob poses challenges due to its complexity. The authors have developed a new methodology to determine both horizontal and vertical variations in the permeability of the gob. Variations of the permeability in the vertical direction are based on a model of caving and block rotation, which considers the effect of block dimensions and fall height on the void ratio. Gob compaction by the overburden and associated permeability changes are determined from a three-dimensional geo-mechanical model which simulates the gob as a strain hardening granular material. The resulting three-dimensional permeability distribution in the gob is then transferred to a reservoir model. The paper demonstrates the application of the method and shows that reasonable results are obtained when compared to empirical experience and measurements.

By Benjamin W. Haynes

This research was conducted as part of the U.S. Department of the Interior, Bureau of Mines program to recover metals, glass, and a combustible fraction from municipal solid waste (MSW). The objective of this analytical study was to determine the concentration of antimony, arsenic, and mercury in samples taken from various sampling areas in the Bureau of Mines raw refuse recycling plant and to compare these values with those for coals used in the generation of electricity. To provide the necessary analytical data, sensitive reproducible ashing-chemical digestion-atomic absorption procedures were adapted from published procedures. It was determined that antimony and mercury concentrations in the combustible fraction of MSW are approximately an order of magnitude higher than those found in coals presently used for power generation;' the arsenic concentration is similar in both fuels.

Jan 1, 1978

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature of the group IVB, VB, and VIR elements. This review was utilized in the Bureau's research to provide erosion-, abrasion-, and corrosion-resistant coatings for valve components used in coal gasification units. This report attempts to bring together the many CVD references that have been published since 1966. Each of the group IVB, VB, and VLB metal coatings were reviewed, and some of their preparation methods, uses, and properties are given. A total of 160 references were found for the nine elements. Isotope separation, stronger steels, solar absorbers, alloys, superconductors, optical fibers, and coatings to increase the life of materials are some of the new uses for CVD.

Jan 1, 1979

By J. B. Zadra, J. M. Gomes, Don H. Baker

Electrolytic deposition at 1,000 ° C in an electrolyte essentially consisting of 7 parts sodium pyrophosphate , 2 parts sodium chloride , and 1 part sodium tetraborate yielded tungsten of 99.9 percent purity . Scheelite concentrates containing 25 to 73 percent WO, and varying quantities of iron , lime , and silica were used as feed materials for the electrolysis . The metal contained less than 0.01 weight - percent each of iron , calcium , silicon , aluminum , carbon , and oxygen . Modification of the electrolyte permitted deposition of equal - quality metal from scheelite concentrates containing higher quantities of iron , calcium , and silica . The electrolytic separation of molybdenum and tungsten was accomplished by minor variations in the operating procedures .

Jan 1, 1964