Search Documents

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By W. P. Diamond, J. R. Levine

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development pro- gram. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

By Maria I. De Rosa

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000° C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 2010

By F. P. Haver

The Bureau of Mines has investigated the electrochemical reduction of lead chloride as a method for producing lead without the pollution problems associated with smelting. It was determined that high-purity metal (>99.9 pct Pb) could be obtained, using PbC12 prepared by ferric chloride leaching of galena concentrate: PbS + 2FeCl3?PbCl2 + 2FeC12 + S°. Optimum results in small-scale electrolytic tests were achieved with a bath consisting of 40 to 70 wt-pct PbCl2 dissolved in KC1-LiCl eutectic, an operating temperature of 450° C, a current density of 2.5 amp/in2, and an electrode spacing of 0.5 inch. In large-scale tests made to develop a cell design for commercial application, the optimum electrode arrangement proved to be a bipolar configuration with horizontal plates. This gave a current efficiency of 86 pct with an energy requirement of 0.52 kwhr/lb lead. To determine the effect of impurity buildup in the bath, 1,200 lb of PbC12 prepared by ferric chloride leaching of galena concentrate was electrolyzed over a period of 2 months. Little deterioration of the metal quality occurred in that time; all of the lead produced had a purity equal to or better than corroding grade (>99.94 pct Pb).

Jan 1, 1976

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

By Charles A. R. Lambly

This paper, which describes the mining practices of the Pend Oreille Mines & Metals Co. at Metaline Falls, Wash., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. ACKNOWLEDGMENTS Acknowledgment is made to L. P. Larson, president, and Jens Jensen, secretary, of the Pend Oreille Mines & Metals Co. for permission to publish this paper. information was supplied by E. Berglund, mine superintendent; Earl Miller, chief engineer; Lynn Kinney, John Currie, and Wally Frick, engineers; Arthur Newman, chief clerk; and Jack Crampton, assayer.

Jan 1, 1941

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By William C. Miller

This report describes investigations by the Bureau of Mines designed to establish the noise level and spectrum of various types of pneumatic rock drills and to furnish information that would be useful in conducting sound measurements in mining environments and in reducing the noise generated in pneumatic drilling. These investigations show that (1) the noise generated by the drills in the frequencies below 100 cps is caused by the impact of the piston and drill steel, in the frequency range between 100 and 2,000 cps by the exhausting of air from the ports, and in the frequencies above 2,000 cps by the resonant frequencies of steel drill parts and of drill steel; (2) satisfactory instruments and instrumentation systems are available for field and laboratory measurements; (3) reliable sound measurements can be made in mining environments; and (4) devices can be developed that will abate the noise.

Jan 1, 1963

By David K. Ingram

Research performed by the U.S. insurance industry has determined that mine subsidence is uninsurable. Consequently, the insurance industry has decided not to voluntarily offer mine subsidence insurance. The U.S. Department of the Interior has long been investigating the effects of mine subsidence. These investigations have resulted in Federal regulations and controls of mine subsidence. This U.S. Bureau of Mines report generally describes mine subsidence, the development of mine subsidence insurance programs, and the eight current mine subsidence insurance programs in the United States. The States that have these subsidence programs include Colorado, Illinois, Indiana, Kentucky, Ohio, Pennsylvania, West Virginia, and Wyoming. Major aspects of the programs include history, administrative and operational procedures, insurable structures, recognition of mine subsidence, major exclusions, claims, insurance premiums, and the economic health of each program. Addresses of agencies involved with mine subsidence insurance are also given. Information within this report can be useful for residential and commercial property owners and mine operators. States that are considering starting or have an existing mine subsidence insurance program can also use this report as a model for initiating or modifying their programs.

Jan 1, 1993

By R. C. Bates

Uranium mine workers? daily exposure to radon daughters was estimated by two methods of sampling, detailed and spot-check. Both methods involve time- weighting measured exposure levels to arrive at an average exposure figure. Random sampling, or sampling without regard for the duration of exposure, has proved inadequate for estimating average exposure levels. During the first phase of the study, the breathing zones of eight workmen in three underground uranium mines were sampled for an entire shift; 20 to 36 radon-daughter samples were collected per man-shift, Analysis of these data indicated that a suitably accurate estimate of the full-shift exposure could be made by time weighting a considerable lesser number of representative radon-daughter samples. This analysis led to the spot-check method of estimating full-shift exposures to radon daughters. Additional detailed studies were made in seven mines to Learn more about the full-shift radon-daughter exposures and to test the spot-check method, In all, 617 radon-daughter samples were taken in 10 underground uranium mines during 26 man-shifts, and the spot-check method was tested 35 times.

Jan 1, 1962

By Michael G. Zabetakis, Aldo L. Furno, Henry E. Perlee

The Bureau of Mines conducted an experimental study with liquid and gaseous hydrogen to determine the hazards associated with the use of liquid hydrogen as an ionizing particle detector in bubble chambers . The glass window , the vacuum chamber , and the vent system were investigated . In addition , a study was made of the detection and ignition of escaping hydrogen and of the available electrical equipment for use in hydrogen atmospheres . Materials such as tempered glass , aluminum , and stainless steel are not penetrated readily by the small fragments formed when fully tempered glass is shattered and propelled by hydrogen at initial pressures up to 100 psig ; long , slender fragments from untempered glass may penetrate thin walls of relatively soft materials such as rubber gaskets and lead . Hydrogen can be vented satisfactorily from a vacuum chamber with a well - designed vent system . However , the rapid leakage of hydrogen into the surrounding air is a serious problem because the available detectors are satisfactory only when the accumulation of hydrogen is slow . Much of the electrical equipment currently available was designed for use in hydrogen- air atmospheres .

Jan 1, 1963

By J. J. de Barbadillo

This report describes a process for recovering chromium and other metals from superalloy scrap. Part I contains the results of laboratory scale experiments which were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the formation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallugical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and an iron-molybdenum residue. Recovery of the principal elements contained in the scrap are chromium(Cr)-93 percent, nickel(Ni)-99 percent, cobalt(Co)-96 percent, molybdenum(Mo)-92 percent. Part II encompasses a preliminary engineering design of a pilot plant capable of treating 100 pounds(lb) of superalloy scrap per hour. Also included is an economic analysis of the operation of the pilot plant.

Jan 1, 1980

By Arel B. McMahan

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the Owlshead Mountains Wilderness Study Area (WSA) in 1982. Within the WSA, subeconomic manganese, iron, zinc, and lead resources were identified at two mines; sample analyses indicate five other mines and prospects may have gold, silver, iron, manganese, and copper resources. Three mines examined adjacent to the WSA have identified manganese and iron resources; and sample analyses indicate manganese, iron, and gypsum resources may exist at two prospects. Greatest likelihood for future identification of mineral reserves is for manganese at the Black Magic Mine in the southeast part of the WSA. The southern half of the WSA contains nearly all identified mineral resources, and properties at which sample analyses indicate additional resources. The most significant are manganese and iron resources at the Black Magic Mine in the southeastern part of the WSA; and the Ellie, New Deal, and Owl Hole Mines adjacent to that part of the area. Manganese and iron minerals filled fractures and replaced limestone in brecciated and faulted contacts with intrusive granitic rocks. In the southwest corner of the WSA, sample analyses indicate four prospects may have gold and silver resources. These precious metals are in gouge zones along contacts where diorite has intruded volcanic rocks. A small identified resource at the Kennedy Boys Lead Mine in the western part of the WSA consists of quartz veins with zinc and lead minerals along a brecciated contact between granite and limestone roof pendants.

Jan 1, 1985

By Sidney Katell

This report, covering the period January 1968 through December 1968, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the tenth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost of engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Lines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress s 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing. 9. Cost Engineering. 10. European Chemical News. 3 11. Hydrocarbon Processing. 12. Industrial and Engineering Chemistry 13. Oil and Gas Journal. 14. Petroleum Engineer. 15. World Oil.

Jan 1, 1969

By M. J. Beus

Researchers at the U.S. Bureau of Mines have developed personal-computer-based data acquisition, instrumentation, and mine visualization and modeling techniques to evaluate a mine accessway in a deep hard-rock mine in northern Idaho. These techniques were applied to a mine shaft in a large silver mine that has been in operation for many years. A very deep, rectangular, timber-supported shaft extending to depths exceeding 2.3 km (7,500 ft) had been deforming continuously as a result of nearby mining, resulting in operational problems. Preliminary visual observations and rock and support monitoring confirmed that severe diagonal distortion was occurring. Extensive field measurements and data analysis confirmed initial observations, provided insights into the cause of deformation, and defined a general approach to structural modeling. Computer analysis of the problem was initiated by developing a three-dimensional model of the terrain. This represented a volume of rock approximately 80 km3 (40 x 1010 ft3) and an area on the surface surrounding the mine 9 km2 (3 square miles). Based on this model, a three-dimensional, finite- element analysis was conducted to establish boundary conditions for sequentially more detailed two- and three-dimensional submodels of the shaft area. Results from the computer study are being used to develop new approaches to mine design and to provide design guidelines for deep mine accessways subject to severe rock-mass loading conditions.

Jan 1, 2010

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By G. H. West, R. L. Sebastian, W. A. Darror

"This bibliography was compiled in the course of research work by the Bureau of Mines on the utilization of magnesites in the West. The results of the research will appear as a bulletin of the Bureau.1. ANALYTICAL METHODS. 11 Knight, X. and Wheeler, W.H. Proc. Iowa Acad. Sci., 13, 1907, 167 (C.A.1, 1370). Describes experience in analysing calcite and dolomite. Reports great excess of oxalate unnecessary and separation of sulphates by alcohol is best.2 Meyerhofer, J. Zeit, Angew. Chem., 21, 1908, 592. Direct determination of Mg as phosphate after removal of SiC2, by keeping R203 in solution with ammonium citrate.3 Merckschen Guano Phosphat Werke. Chem. Ztg., 33, 1909, 545 (C.A. 3, 2281). volumetric analytical methods.4 Popel, M. Zeit. Angew. Chem., 21, 1908. 2082 (C.A, 6, 412). Determination of CaO in presence of CaC03.5 Blasdale, W.C. Jour. Am. Chem. Soc., 31, 1909, 91? (C.A. 3, 2658). Studies of separation of Ca from Mg.6 Hundeshrgen, F. Zeit. Offent. Chem., 15, 1909, 85 (C.A. 3, 1853). Valua¬tion of caustic magnesia by analysis. Volumetric methods.7 Frerichs, H. and Krosberg, W. Apoth. Zeit., 24, 1909. 679 (C.A. 3, 2996). Tecting magnesia alba for Fe.8 Schoorl, N. Zeit. Anal, Chem., 48, 1009, 593 (C.A. 4, 5E9). Microchemical tests for Mg, Li, K. and Na.9 Heyer. Chew. 2Ag., 33, 1009, 1157 (C.A. 4, 1588). Determination of CaO in presence of CaCO3. CaCO3 in soluble in cold neutral solution of NH3 salts. Solubility Is diminished by free NH4OH."

Oct 1, 1923

By Stephen Utter

Stresses induced by block-caving mining were estimated from in-place measurements of strain or deformation in rock and concrete around mine openings. The four types of gages used for measurements in the Climax Molybdenum mine during 1959-61 were Whittemore gage, Carlson strain meter,2 Valore strain cell, and Climax extensometer. Gage performance in the laboratory was evaluated by stressing instrumented rock and concrete specimens in a universal testing machine and by comparing measurements taken by the gages and a standard gage. Gage performance in the mine was evaluated by comparing measurements taken during an 18-month test. The Whittemore gage, Carlson strain meter, and the Climax extensometer proved suitable for the investigation; the Valore strain cell, effective in the laboratory tests, gave erratic measurements in the mine.

Jan 1, 1965

By H. D. Hess, C. P. Mabie

This report describes in detail the results of petrographic research conducted on 21 phosphate ores representing important deposits in southwestern Montana , southeastern Idaho , and northeastern Utah . The ores are described and categorized by mineralogical and chemical composition , thermal behavior of organic carbon , and textural constitution . Descriptive and genetic classification schemes applicable to western phosphate ores are discussed ; results from related studies made of the collophane mineralogy are also presented . The latter studies were centered on determining unit - cell dimensions and CO₂ , P2O5 , and fluorine content of collophane concentrates of 11 high - grade phosphate- rock hand specimens selected solely for this purpose . On the basis of this investigation , operational methods have been developed for quantitatively describing textural and compositional features that are likely to be significant in determining the response of phosphate ores to conventional beneficiation treatments ; systems for classifying the ores in relation to these features have been proposed . Studies to date point out distinct textural and compositional variations in the western phosphates and illustrate their importance in determining optimum beneficiation procedure .

Jan 1, 1964