Search Documents

By W. E. Wallace, V. Castranova, F. Saus, D. Bates, C. A. Hill, V. Vallyathan, M. J. Keane

"Two in vitro systems are being developed to model initial stages in the interaction of respired dusts with the acinar region of the lung. Incubation of quartz and kaolin with dipalmitoyl glycerophosphorylcholine, a major component of pulmonary surfactant, suppresses the prompt C)1otoxicity of both dusts as measured by in vitro enzyme release from pulmonary macrophages or assay by erythrocyte hemolysis. Additional data is presented to quantitate the detoxification of quartz and kaolin by dipalmitoyl lecithin. Subsequent incubation of lecithin treated dusts with phospholipase enzymes results in partial to complete restoration of the assayed cytotoxic potentials, dependent on the lipase activity applied, the incubation time, and the mineral. Restored cytotoxic potential is due to removal of the prophylactic lecithin surface coating and/or due to residual lysolecithin which is produced by the partial enzymatic digestion of lecithin. Data is presented on the contribution of each mechanism to the restored toxicity. Again, this is dependent on the mineral used, the lipase activity applied, and digestion time. Additionally, a system is under development to challenge pulmonary macrophages in culture with native and surfactant treated dusts. A preliminary test of the dipalmitoyl lecithin - quartz rabbit pulmonary macrophage system is presented to illustrate the method.IntroductionRespirable quartz dust exposure is known to cause librotic lung disease; respirable clay dust exposure is less likely to do so as indicated by epidemiologic data on occupational exposures and by animal model studiesP·7) The hypothesis that damage to pulmonary macrophages in the acinar region of the lung by respired dusts is an early event in the disease process requires consideration because kaolin clay and quartz dusts are comparably cytotoxic to pulmonary macrophages in vitro.(3•9)"

Mar 1, 1989

By John D. Bardill

This report covers the magnetic surveying done in the Plattsburg area , which was part of a general survey, of magnetite deposits in New York State . Other areas being surveyed are the Star Lake district , St. Lawrence County ; Brewster district , Putnam County; and the Sterling district , Orange County. Reconnaissance indicated an area about 3 miles long and 1,200 feet wide , but detailed surveys have been completed on only a portion of that area . In several districts , surveys of this type have served as a basis in the selection of areas for exploration by diamond drilling by the Bureau of Mines .

Jan 1, 1947

By G. R. Strimbeck

Experimental work is report on the gasification of 90-percent through 200-mesh, strongly coking Sewickley-bed coal with oxygen and with steam in three temperature ranges, namely, 2,700° to 3,400° F., 1,600° to 2,000° F., and 230° to 250° F. Thirty-one runs have been made, during which 56,000 pounds of coal have been charged to the generator at feed rates of 200 to 450 pounds of coal per hour. The average results, not the optimum results, are given in the following tabulation:

Jan 1, 1950

By Harry V. Makar

As part of a continuing research program for conserving domestic mineral resources, the Bureau of Mines is investigating new and improved scrap identification techniques to improve sorted mixed scrap purity. This report focuses on various classes of wrought and cast copper alloys produced with recycled scrap. Based on a survey of the literature, principal alloys, such as the brasses and bronzes, are examined with respect to impurity elements and their effects on metallurgical behavior. Effects of elements such as lead, antimony, iron, chromium, and aluminum are discussed. The metallurgical effects described include hot shortness, fire cracking, and undesirable phase transformations.

Jan 1, 1985

Objective: To provide a safe, practical, cost-effective method for measuring coal rib thickness during highwall mining.

Jul 1, 2008

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010

By Paul M. Tyler

Calcium chloride is a conspicuous example of a former waste product that has found a place for itself in the onward march of civilization. Formerly considered a troublesome constituent of the effluent sewage of many chemical manufacturing plants and salt works, it has now become a commercial product of substantial importance, with sales aggregating almost six million dollars in 1929. The point has not yet been reached where it would seem profitable to undertake large-scale production of calcium chloride as a main product, but as a byproduct it has become an item that warrants serious consideration by all who are in a position to recover it at sufficiently low cost. The largely increased demand for bromine and for certain magnesium salts, which are likewise potential byproducts associated with calcium chloride in most salt-works bitterns (and brines generally), adds further impetus to commercial research directed toward the fuller utilization of the natural saline resources of the United States.

Jan 1, 1934

By H. F. Weaver

The 17th National First-Aid and Mine Rescue Contest was held in the Kentucky Fair and Exposition Center, Louisville, Ky., October 2, 3, and 4, 1957. The meet was under the auspices of the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with the National Coal Association, United Mine Workers of America, State mining departments, local mining institutes, and coal operators' associations. The Arrangements Committee, as authorized by the General Committee, made all the necessary arrangements for conducting the 1957 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators' Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1958

By W. M. Dressel

A simple, reliable field test for beryllium in rocks has been developed by the Rolla Metallurgy Research Center of the Federal Bureau of Minas. A small portion of the pulverized rock is fused with a sodium carbonate-sodium hydroxide flux in a wire loop. The fused mass is dissolved in water, a few drops of quinizarin solution are added, and the solution is viewed under ultraviolet light. A pink-to-orange fluorescence reveals the presence of beryllium in a sample containing as little as 0.013 percent beryllium (0.26 percent beryl). INTRODUCTION New and potential uses for beryllium make necessary a more intensive search for this metal, which is so similar to aluminum in its chemical reactions that it is not separated from aluminum in ordinary chemical analyses. The principal ore mineral of beryllium is beryl, a beryllium-aluminum silicate, which contains only 5 percent beryllium. This mineral is so similar to quartz in appearance that it is not always possible to distinguish one from the other in the field. While the distinction may be made easily with a petrographic microscope, few prospectors have access to such an instrument, and fewer still know how to use it.

Jan 1, 1960

By Phillip M. Busch

VANADIUM was discovered in 1801 by Andres Manuel del Rio, a professor of mineralogy at the School of Mines in Mexico City. Del Rio called the new element erythronium. Later, he decided that this was not a new element but a form of chromium. Not until 1831 did Nils G. Sefström, a Swedish chemist, positively determine that the metal was a new element which he named vanadium, after Vanadis, the Scandanavian goddess of beauty. From 1831 to the 1860's and 1870's, the comparative scarcity and high cost of vanadium restricted its commercial use. Shortly after 1870, more information was obtained on the physical and chemical properties of the element. Thereafter, research on vanadium has dealt largely with its use as an alloying element in steel and nonferrous metals. Vanadium is a widely distributed element in the earth's crust. It is more abundant than many metals but is disseminated in small quantities throughout a great variety of rocks. Relatively few deposits have contained ore of a grade suitable to warrant development for vanadium alone. It is produced in conjunction with uranium, iron, titanium, aluminum, and lead-zinc ores.

Jan 1, 1961

By S. S. Peng

Successful longwall mining requires a good roof control. A good roof control implies that: (1) no excessive pressure is build up in the face powered supports, and (2) chain pillars are designed in such a way that panel entries are well protected and interactions between adjacent panels are minimized. A clear understanding of strata behavior around longwall panels due to face movement is, therefore, the foremost requirement for achieving better roof control. This dissertation is designed to analyze the effects of strata behavior on longwall panels due to the mining activities. The following topics are studied: (1) the weighting, phenomena and their effects on front abutments, and (2) the chain pillar stability and pillar design under various roof conditions. Three dimensional finite element analysis was employed. The effect of parameters such as overburden depth, mechanical properties of the immediate roof and main roof, panel width, and size of chain pillar on (t) and (2) were analyzed. Four typical models were utilized to simulate various phases of panel extraction under various combinations of the above parameters; model one is to simulate the beginning of panel mining; model two is to simulate the situation that longwall face has passed more than half of panel length; model three is to simulate the completion of panel production; and model four is to simulate the second panel mining. The following formulae have been developed by applying multiple regression model to analyze the finite clement results: (1) a formula that classifies the type of root strata at the face area. (2) formulae that predict the first weighting and periodic weighting lengths. (3) a formula for design of the chain pillar size. Case studies were performed to check the validity of the formulae proposed. Comparison of the formulae proposed for the chain pillar design with other formulae were also performed.

Jan 1, 1984

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion - exchange X- ray spectrographic method was developed and evaluated for determining trace amounts of cobalt and nickel in high - purity tungsten and tungsten trioxide . The sensitivity for both cobalt and nickel is in the range from 0.2 to 0.5 μg ( 0.04 to 0.1 ppm , based on 5 gram samples ) . Accuracy at the 5 to 20 μg level is ±10 percent of the amount present . Approximately 16 hours elapsed time is required for analysis

Jan 1, 1963

By Joseph J. Wallace

1. The Investigation shows that there are six coal beds of major importance in McDowell County from the standpoint of present production - Pocahontas No. 3, Pocahontas No. 4, Pocahontas No. 5, Sewall, Beckley, and Pochontas No. 6 - and five beds of minor importance - Iaeger, Douglas, Welch, Pocahontas, No. 9, and Eagle. The Pocahontas No. 3 bed contains the largest remaining, known reserves. 2. Known measured, and indicated reserves in all beds, based on a minimum thickness of 174 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,217 Trillion short tons as of January 1, 1951. Of this total, 1,731 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these area, such reserves should be added to he total estimated reserves.

Jan 1, 1952

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By D. L. Yopps

In research conducted by the U.S. Bureau of Mines, platinum-group metal (PGM) flotation concentrate from the Stillwater Complex, MT, was subjected to biooxidation using Thiobacillus ferrooxidans in an effort to break down the sulfide minerals and liberate the associated PGM's for subsequent chemical leaching. Bacterial preleaching oxidized up to 94 pct of the sulfide present, destroyed the PGM-bearing pentlandite [(Ni,Fe)9S8] mineralization, and dissolved most of the nickel in the concentrate. Cyanidation at 80° C proved to be the most attractive chemical leachant, removing 34 pct of the platinum, 76 pct of the palladium, 94 pct of the rhodium, and 97 pct of the gold from the biooxidized concentrate. Research also indicated that increased sulfide oxidation during the preleach phase led to improved PGM recovery in the subsequent chemical leaching phase.

Jan 1, 2010

By V. F. Parry

This report is the first substantial description of the carbonizing process and the details of experimental work conducted at the Denver laboratories under a coopeative agreement between the Bureau of Mines and the Texas Power & Light Co. It presents the results of tests on several Texas lignites and other typical western coals that have been processed in the first pilot plant operated at Denver. Investigations on drying fine coal in the entrained and fluidized state have been under way at Bureau of Mines Denver laboratories for several years. Reports on this work were published in 1949 and 19505/ describing the theory and practice of re-moving inherent moisture from the lower -rank coals. The investigation did not include a study of the removal of surface moisture from fine fuel. Private industry in Canada became interested in the possibilities of drying fine coal, employing the closed-circuit system and techniques recommended by the Bureau. Large, commercial-scale drying units were built by a Canadian company, which successfully demonstrated that surface moisture could be removed from fine coal at high efficiency and capacity ill drying units similar in design to those developed by the Bureau.

Jan 1, 1953

By Alfred Bellows

The objective of this contract is to design, build and demonstrate a support system to improve roof control in the entries of longwall mines. The objective of this phase has been the detailed design of such a system and the selection of a test site in which to perform the pilot demonstration. The result is a complete set of detail drawings or specifications which define the three major components of the system. The Gate Support is a variation of a face chock which has an extended canopy and additional hydraulic legs to protect the region of the face-entry intersection. The Entry Support is a steel beam and hydraulic prop set which is reusable and serves to support the first 100 or more feet of entry inby the longwall face. The Transporter is a bolter-like vehicle with a crane used for installing and retreating the beam sets. The test site selected is CF&I's Allen Mine in Colorado. They presently use simi¬lar steel beams and expect the FMA support system to be more effective as well as recoverable. It is recommended that the completed drawings be used to build a prototype system and test it first in a remote section of the mine and then in the active longwall tail entry.

Jan 1, 1978

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By Lloyd Williams, R. E. Hershey, B. W. Gandrud

"1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come :from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sevanee has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although some coal has been produced from them.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on l,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed ·were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal are estimated in beds 28 inches and more 'thick. This recovery is based on total thickness of coal in the bed (less partings 3/8-inch thick or more), rather than on the thickness of the coal actually mined. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian Region. The combined weighted average recovery for the Sewanee and Battle Creek beds in Marion County, as determined by this investigation, is 60.9 percent. Based on this, the recoverable reserves of coal in Marion County are estimated at 34 million tons."

Oct 1, 1955

By H. W. Kilau

The U.S. Bureau of Mines is evaluating water spray additives for the purpose of improving respirable dust control during coal mining operations, with particular emphasis on the longwall shearer. Recent field tests of surfactant-polymer reagents at two production longwall operations have shown favorable respirable dust reductions compared with water sprays containing no additive. Gravimetric dust samples obtained by a technician downwind of the shearer while following or preceding the machine showed dust reductions in the range of about 40% to 60% for some of the reagent formulations compared with using water alone. Three polymers were tested: two polyethylene oxide compounds of different molecular weight and hydroxypropyl methylcellulose (HPMC). All were effective for dust reduction, and two were cost effective when used in combination with sodium di(2-ethylhexyl) sulfosuccinate surfactant. How-ever, the use of these reagents requires the longwall operator to be more aware of headgate dust control. Experimental evidence indicates that dust captured by reagent-treated sprays at the shearer can be reemitted in the headgate area if stagcloader-crusher sprays and other dust controls are inadequate.

Jan 1, 2010