Search Documents

By Don M. Coulter

"INTRODUCTION The Margerum bauxite district, in Colbert County, Ala. was investigated in December 1940 and in February 1943 by R. W. Smith of the Bureau of Mines .3/ A geologist of the Federal Geological Survey investigated and mapped the district in the fall of 1942.These preliminary investigations indicated bauxite showings over an area about a mile long by 2,000 feet wide. It was felt that the chances were good for finding one or more large deposits of low- to medium-grade bauxite. The location - within 35 miles of the alumina plant of the Reynolds Metals Co. atLister Hill, Ala. – made it especially attractive. A field office was established in Iuka, Miss., on May 19, 190,, and mineral agreements were executed with four landowners covering 1,146.6 cores.The drilling on the project was done under contract. The power drilling was supplemented by a labor crew that drilled hand-auger holes, where there was little or no gravel overburden, and sampled the old test pits.The Federal Geological Survey, after thorough study of the district, recommended 54 drill holes 4/ to delimit the known deposits and to search for possible extensions. After the drilling started, many of these locations eliminated, and others were changed upon the basis of information gathered from the holes as they were drilled."

Mar 1, 1948

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By R. R. Trengove

This paper is one of a series published by the Bureau of Mines on mining methods and operation practices. It describes the open-pit mining method and operations of the Kaiser Steel Corp. Eagle Mountain iron-ore mine, which is in the extreme southeastern part of California 175 miles east of Los Angeles in Riverside County. Nearest town to the mine is Indio, which is 60 miles away by an excellent highway (fig. 1). Elevations at the deposit vary from 1,400 to 3,000 feet. Figure 2 is a plan map of the Eagle Mountain iron mine. Kaiser Steel Corp. built a model camp at the mine, with all modern conveniences (fig. 3). The camp, comprising 145 homes, dormitories, mess hall, commissary, post office, and recreational facilities for 600 people, is at 1,390-foot elevation. The area has winter-resort weather between October and May, with occasional drops of temperature to 25° at night. From June to September temperatures sometimes rise to 1200 during the day. Rainfall is scant, approximately 2 inches a year, the majority of which comes as cloudbursts during the summer months.

Jan 1, 1956

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By Ernest E. Berger

"INTRODUCTIONOne of the outstanding problems in the normetallic industries, and one which involves two of the greatest of these industries, cement and gypsum, is the reaction of Portland cement with calcium sulphate. To all Portland cement clinker there is added in the manufacturing process, a small amount of retarder, as a necessary ingredient of the finished product. This retards the initial set, increases the strength, and adds to the plasticity of the cement so it will have the desired working and setting qualities. The retarder commonly used is gypsum, (CaSOA.2HO), which is the hydrous form calcium sulphate. Calcium sulphate is also available as plaster of Paris (CaSO4 1/2 HC) and anhydrite (CaSO4). The purpose of this inquiry was to determine the form or mixture of forms best adapted for retarder. The problem is complicated by the fact that cement clinker is a complex mixture of calcium silicates and aluminates, and that clinker from different mills, making cement of approximately equal quality, differs considerably in chemical constitution. Thus the same retarder may give very different results with different types of clinker, especially in the percentage of retarder required for the same degree of retardation.It has been known for some time that a small percentage of plaster of Paris will greatly retard the time of set of Portland cement as well as increase its strength and plasticity, but whether gypsum and anhydrite will have a similar effect is as such disputed question. The offects of gypsum have received little consideration in laboratory research because, even though it will not retard a clinker when the two are mixed in the laboratory, as has been noted in some instances, the cement will have a normal set when the two arc mixed in the large tube mill at the plant, so that practically, gypsum seems to be equally as goou as plaster of Paris, and because of the great saving in cost it has been used almost exclusively."

Sep 1, 1925

By E. E. Donath, L. L. Hirst, L. C. Skinner

Two processes are available for the production of synthetic fuels from coal high-pressure hydrogenation and the carbon monoxide-hydrogen synthe- sis. This paper presents some ideas and new developments in coal hydrogen- ation that have been incorporated in an estimate for the production of 30,000 barrels per day of liquid fuels, mainly gasoline. A few comparisons of the processes will be helpful before discussion of the details of pro- posed improvements in the hydrogenation process. The principle of the high-pressure hydrogenation process ie the addi- tion of hydrogen at pressurea in the range of 3,000 to 10,000 p.s.i. to coal at elevated temperature and with the help of catalysts. On the other hand, the principle in the Fischer-Tropsch synthesis is the complete break-down of coal into a mixture of carbon monoxide and hydrogen, followed by the catalytic combination of these two gasse into hydrocarbons or suitable catalysts. For the synthesis, moderately elevated pressures of about 350 p.8.1. will bo used in the immediate future, although it can be carried on at atmosphoric pressure with certain catalysts. The products of these two processes using coal as raw material are almost as differont as hydrocarbons can be. The products of the high-pres- sure hydrogenation of coal reflect the original constitution of the coal. They are, therefore, rich in ring compounds, both aromatic and naphthenic, but, due to the action of highly comprcesed hydrogen and catalyst, are satu- rated and very stable. These constituents give the gasoline a high octane number and excellent rich-mixture performance, combined with good gum and storage stability. Therefore, this gasoline is suitable for aviation gaso- line or base stock. The Diesel fuel can be hydrogenated to a centane number of 45 or higher, which is entirely satisfactory for operating normal Diesel

Dec 1, 1948

By John C. Machisak

THE INJURY data and experience at quarries and related plants of the United States are presented in this publication under the following general sections (A) General injury experience: Tables 1-3: Current data on number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 4-5: Current data on number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment, data. (C) Injury experience by States: Tables 6-20: Current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data. (D) Selected injury data: Tables 21-30: Current data on various selected factors of operating conditions at different kinds of quarries, including employment size-groups, length of shifts, comparative severity of injuries, and injury data and related employment experience at dimension-stone and nondimension-stone quarries and at underground quarries. (E) Historical injury experience: Table 31: Injury and employment data on the quarrying industry for 1911 through 1957. Statistical data on injuries and related employment in the quarrying industries have been collected annually from the operating companies since 1911. Reporting to the Bureau of Mines is voluntary; there is no Federal law compelling operators of quarries and related plants to supply such data. Data presented herein may not be complete for the entire industry. They are however, believed to be representative of the hazards common to all quarry and related workers. Moreover, the figures are comparable as between States-a significant fact in view of the lack of uniformity among the States with regard to the classes of injuries covered by State reports and other factors that tend to make it impracticable or impossible when using State records to

Jan 1, 1960

By Gene F. ] [Faufaul

This contract was concerned with the design, development, fabrication and testing of an improved tamper-proof filter cassette assembly for use in the, collection and evaluation of dust particulates, primarily in mining areas. This report presents the design effort, fabrication and tenting of five- prototypre unit$ as well as the design and production of 1000 filter cassettes with sampling heads. This new improved filter cassette has been tested and approved by NIOSH as meeting the requirements specified in the contract.

Jan 1, 1978

By R. A. Meyer

A table that greatly simplifies determination of metastable transitions in mass spectra has been prepared. All the mathematically possible metastable transitions of any compound whose molecular weight lies between 26 and 150 can be determined from the table without calculation. The method of utilizing the table is described, using selected peaks from the spectrum of normal butane for illustration. In the mass spectrometer, ions are formed in the isatron and accelerated through a series of slits. Most of these ions reach the collector without further change, but a few dissociate in transit to form new ions. These ions appear in the mass spectrum at neither the mass--to-charge ratio (m/e) of the original ion nor that of the new ion. A formula that relates the appearance of these new ions to the ion from which they were formed is: [ ]

Jan 1, 1957

By Stephen C. Tadolini, Yunqing Zhang, Thomas M. Barczak

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high-loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that's proportional to the noise level.

Jan 1, 1975

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By James H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER ACT) established a Technical Study Panel (The Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the Belt Evaluation Laboratory Test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 36- to 42-in wide conveyor belt. Due to today?s coal haulage capacity, the mining industry is using 72-in and wider conveyor belts. The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2010

By Paul W. Johnson

A computer program for calculating capital and operating costs from material and energy requirements and equipment costs for use in preparing cost estimates for metallurgical process evaluations has been written by the Bureau of Mines' College Park process evaluation group. The program permits rapid recalculation of processing costs when changes of data or equipment are desired, and produces tables of capital and operating costs suitable for publication. Equipment cost summary tables for each process section end supplemental information for input-data checking is included in the computer printout. The program is written in Fortran IV except for several subroutines which are written in machine assembly language for the IBM 7094.3 With a few modifications, the program can be used on other computers.

Jan 1, 1969

By C. B. Manula

This report is volume 4 of at. eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment: The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Roof Support subsystem of the Master Design Simulator. This model is based on popular roof support practices for different geological environments with related restrictions imposed by the Coal Mine Health and Safety Act of 1969. From geological sections, the model determines the anchor horizon for roof bolts and the density of roof support necessary. The roof support subsystem is tied to both the geology and reserves subsystem and the production subsystem of the Master Design Simulator, but can also operate as a free standing model. Several case studies are presented showing the application of the model. A detailed user's manual, including a program listing, is presented in the appendices.

Jan 1, 1974

By R. J. Leary

Iron and steel scrap has accounted for 45 to 50 percent of the metallics used by the steel industry. In an electric furnace which utilizes a 100-percent cold charge consisting of about 99 percent scrap and 1 percent pig iron, sensible heat from molten pig iron is not present as it is when hot metal is charged to open hearths and converters. A study of means for more efficient utilization of iron and steel scrap in steelmaking indicated that the time and fuel requirements to melt scrap were important cost factors, particularly in arc-furnace steelmaking. A process to preheat scrap economically prior to charging into the arc furnace has been developed, utilizing efficiently the heat from combustion of fossil fuels as a substitute for electric-arc heating in the initial stage of arc-furnace steelmaking. Scrap is loaded into a portable vertical cylindrical furnace body that is open at the top and has a perforated dropout door at the bottom. In the heating operation, the furnace body containing scrap is placed upon a hollow base connected to a flue, and then the burner and combustion-chamber unit is lowered on top of the furnace body. The stream of hot-combustion products flows down through the bed of scrap imparting heat to it, and the cooled gases exhaust through the flue. After the heating operation the furnace body containing hot scrap is transported to the arc furnace for charging. Thus, the furnace body serves as a charging bucket for top-charged arc furnaces, enabling this preheating process to be integrated into existing material-handling patterns in many arc-furnace plants.

Jan 1, 1961

By S. Raghavan

An investigation of the possibility of improving the grinding characteristics of a gabbro ore containing copper and nickel sulfides via a thermal shock treatment technique has been carried out. The results obtained indicate that the breakage characteristics of the gabbro are particles can be significantly improved by preheating the are particles to a temperature around 400°C followed by rapid water quenching. For a given power input and feed size, the thermally treated material produces a product of much finer distribution than the untreated material. An assessment of the improvement in grindability has been made by calculating feed size selection functions for untreated and heat-treated materials.

Jan 1, 1981

By MINE SAFETY BOARD

RECOMMENDATIONS OF THE UNITED STATES BUREAU OF MINES ON CERTAIN QUESTIONS OF SAFETY AS OF FEBRUARY 3 , 1933

Jul 1, 1933

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and an extensive literature has resulted. Usually each individual paper has placed emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and ran extensive literature has resulted, Usually each individual paper has placed 'emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941