Search Documents

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California in 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemica 1 manufacturing; a shift in requirements from metals to nonmeta ls, from inorganics to organics, from natura 1 to synthet ic materia ls , and from distant to local sources of supply.

Jan 1, 1965

By Lee Ann Gardner

This U.S. Bureau of Mines publication presents a case study of the processes used in permitting the Nome Offshore Placer Project, a gold mining project offshore Nome, Alaska which operated from 1985 through 1990. The mining project, developed by Western Gold Exploration and Mining Company, Limited Partnership (WestGold), used the BIMA, which was at the time the largest bucketline mining vessel in the world, to dredge gold from the ocean floor. This case study reviews the permitting process from the regulators' and industry's perspectives, as well as characterizing the efficiencies and inefficiencies associated with this case. The Federal, State and local laws applicable to the Nome Offshore Placer Project are identified, agency jurisdiction and interagency relationships are explored, and the chronology of the permitting process is examined. The regulatory authorities for both environmental monitoring and post-mining monitoring are delineated. Significant milestones affecting the project and required regulatory submittals are also included. The case study of the Nome Offshore Placer Project is detailed with respect to agency involvement and coordination, approaches to permitting from both the regulators' and developer's perspective, environmental issues, and permit stipulations which were unique to the project. The advantages and disadvantages of these topics are discussed.

Jan 1, 1992

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1951

By Manuel Gomez

This report presents prediction equations for 12 variables that are indicative of metallurgical coal quality. The variables include six for coke strength and six for carbonization product yields. All variables were predicted for coking coals having volatile matter contents from 16.3 to 42.1 percent, dry basis. The prediction equations, developed by mathematical-statistical techniques, were based on information from the proximate and ultimate analyses, the size consist, and the petrographic composition of bituminous coals carbonized in BM-AGA retorts at 800°, 900°, and 1,000° C. The equations were evaluated for validity with independent data derived from the 900° C carbonization of 33 binary blends of various coals and 22 binary blends of Pocahontas No. 3 low-volatile bituminous coal with 11 high-volatile bituminous coals. Results show that metallurgical coal quality can be predicted ahead of mining because data used to derive the prediction equations can be obtained at the time of exploration. Capability to forecast coal quality is useful in mine planning and should provide basic information for optimization of blending and crushing techniques and thus lead to the production of uniform coke.

Jan 1, 1970

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By J. P. McCullough

In 1943, the Federal Bureau of Mines began a program of thermodynamic investigations of petroleum constituents and related compounds. These systematic, long-range studies, which were conducted in the thermodynamics laboratory of the Bartlesville Petroleum Research Center and are still continuing, have resulted in a substantial quantity of data valuable to the petroleum industry and science in general. As separate phases of these studies were completed, the findings were promptly reported in the scientific press. During the past 16 years, 89 journal articles, giving the results obtained for individual compounds and small groups of related compounds, were published, mainly in the Journal of the American Chemical Society and the Journal of Physical Chemistry. In addition, members of the Bureau staff have contributed six chapters to specialized reference books. This circular, prepared in response to many requests, lists these 95 published papers, giving an abstract of the contents of each, as well as titles, authors, and literature citations. The journal articles are listed in the order of their preparation, which closely approximates the chronological order of their publication; hence, the item number to the left of each citation corresponds to the assigned contribution number. For the convenience of the reader, the abstract section is followed by a condensed bibliography, arranged alphabetically by senior author and keyed to the abstracts by appropriate contribution numbers in parentheses after the entry.

Jan 1, 1961

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

In 2005, a total of 2,063 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 14.1% of all mining operations. ? Bituminous mines comprised 92.6% (n=1,911) and anthracite mines 7.4% (n=152) of coal mining operations. ? Approximately 70% of all coal mines were located in three states: Kentucky (28.0%), West Virginia (21.8%), and Pennsylvania (20.6%).

Jan 1, 2008

By John D. Bardill

This report covers magnetic surveys in the Dannemora arca , which was part of a general survey of magnetite deposits in New York started in 1943 . The objective of these surveys was to afford a basis for the selection of exploration projects .

Jan 1, 1947

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By Walter R. Storms

The Iron Mountain tungsten deposits first were visited by a field party of the Federal Geological Survey in May 1942 while beryllium deposits in that district' were being examined . Later they were examined by F. A. Rutledge , an engineer of the Bureau of Mines , and an exploration project was recommended , work upon which began in March 1943 and was terminated in April 1943 after intensive trenching and sampling had been completed .

Mar 1, 1947

By Margaret E. Harris

The formation of nitrogen oxides, the decay of carbon monoxide, and the concentrations of residual hydrocarbons in the secondary combustion zones of propane-air and methane-air flames were studied in three enclosed burners designed to simulate gas appliances such as space and water heaters. The effect of thermally or chemically perturbing the combustion gases above these flames was determined theoretically and by means of factorial experiments. The concentrations of air pollutants and the flame temperatures were measured, and the effects of ingress of secondary air into the primary and secondary combustion zones, flame stability, burner port surface, and simulated recycling of combustion gases were noted. Based on this study, four principles were derived that, applied to gas appliance design, will insure minimal emissions of these air pollutants: 1. Oxides of nitrogen can best be kept low by depressing peak temperatures to about 3,050° F. 2. If this is not possible, then the secondary combustion zone should be cooled rapidly to this temperature. 3. Carbon monoxide concentrations can be limited by rapid induction of secondary air. 4. Hydrocarbon concentrations can be controlled by designing for well-seated, stable flames. In addition, empirical reaction rates were derived that predict the concentrations of nitrogen oxides and carbon monoxide in the primary and secondary combustion zones.

Jan 1, 1970

By John A. Kiefer

Ground fault and overcurrent protection criteria for coal mine a.c. distribution systems were examined under a Bureau of Mines funded investigation. The report begins with a literature review which discusses relaying topics including instrument transformers, ground-fault pickup methods, static relaying, and comparison of relaying techniques. A chapter on ground-fault relaying provides recommendations for maximum and minimum pickup levels as a function of maximum ground current and power system line-to-ground capacitance. Research in the area of phase overcurrent protection has resulted in a complete set of procedural recommendations for the selection and setting of overcurrent relays and current transformers, molded-case circuit breakers, and distribution system fuses in coal mine power systems. The final chapter, which discusses relay system maintenance, introduces a unique test set which was developed by KETRON and used to test the performance of relaying systems in coal mines.

Jan 1, 1980

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997