Search Documents

By Jason Rock, Rob Thompson, Lee Julian

This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

Feb 1, 2020

By D T. Froedge

Before this study was started, literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast-induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet.

Jan 1, 1983

By A. Cobbii, M. Kasliki, W. Birchi

The Department of Mining and Mineral Engineering at the University of Leeds has a long history of research into the environmental impacts of blasting from quarries and opencast mines. This paper gives an outline of a detailed case study into the structural damaged induced in a rock walled tunnel with a brick lined crown due to close proximity quarry blasting. The test site Taffs Well Quarry is located in South Wales in The United Kingdom and has a disused railway tunnel situated within the south eastern comer of the quarry site. Quarry development plans included the working of this area and therefore the deliberate destruction of the central section of the tunnel.

Jan 1, 2001

By Randall M. Wheeler

Computer analyses of single hole signatures are often used to help blasting operators predict the type of ground vibration effects that may be produced from production blasts incorporating various delay intervals. Frequency analyses of single hole waveforms and subsequent multi-hole waveform simulations can allow an operator to determine the best type of delay intervals to use in order to minimize low frequency ground vibrations.

Jan 1, 1989

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By Dr. Tristan Worsey, Dr. Jhon Silva-Castro

Confinement is an important aspect of blasting. Reducing and increasing confinement can determine whether a blast design performs properly. Over-confined shots usually have poor fragmentation, higher vibrations, and stemming ejection, and unconfined shots usually have a lot of air blast and fly rock. When talking about confinement in blasting, static confinement conditions are typically referenced. Static confinement conditions are ruled by free faces, shot muck, burden, spacing, stemming, hole depth, toe, etc. All these conditions exist in a static state. Static confinement conditions are generally analyzed before the shot takes place, but once the shot starts, the conditions will change according to the sequence and delay of the shot. Once the shot starts, Dynamic confinement takes place. For the authors, Dynamic confinement is the confinement conditions that exist for the charge when it fires and should account not only for the variables included for the static confinement but also for the time and sequence of the shot. The paper explores the theory of dynamic confinement and its role in influencing blast performance. Time and sequence are the main influencers of dynamic confinement and will be the focus of the paper. How to generate the appropriate timing based on blast design, dynamic confinement, static confinement, and geology will also be discussed.

Jan 21, 2025

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By Jerome H. Stofleth

In June of 1998, the DeBruce Grain Elevator was devastated by an accidental explosion caused by the unintentional ignition of grain dust. The DeBruce grain elevator was the largest ‘single head-house’ grain elevator in the nation. It was comprised of 450 cylindrical grain silos, 30 feet in diameter by 120 feet tall, with a centrally located headhouse. Immediately after the explosion, rescue operations were started for seven missing workers. The Federal Emergency Management Agency (FEMA) had taken over operations of the site by day two. On day three FEMA contacted the Washington DC office of the Department of Energy for explosive expertise, who in turn contacted explosives experts at Sandia National Laboratories (SNL) and Los Alamos National Laboratories (LANL). FEMA was looking for guidance in making the decision to downgrade their operation from a rescue to a recovery operation. Based on some chemical equilibrium calculations, and basic explosive engineering techniques, the SNL/LANL team was able to provide the necessary input to allow the decision to be made for the operational downgrade. At this point, only one worker remained un-recovered.

Jan 1, 2004

By Ann Barron

Even though you think your company’s safety program is the best it can be, equipment, processes, supplies, surroundings and people do not always behave or react as expected. Consequently, needless accidents occur each year at quarries, construction sites, surface mines, and other locations where explosives are used. While blasting accidents account for only a small portion of the total accidents reported, the severity rate for blasting accidents is higher than for any other accident category.

Jan 1, 2007

By W. Birch, G. D. Rangel-Sharp, L. Bermingham

For many years, the accepted method of Measuring the Velocity of Detonation (VOD) in blast holes has been to use an electric cable of a constant resistance per metre. Thus as the wire is consumed by the explosive in the blast hole, the change in resistance is monitored and when this data is plotted against the time period of the in hole explosion, the VOD can be calculated.

Jan 1, 2011

By Tie-jun Tao, Ming-sheng Zhao, En-an Chi

"Karst landform is a special kind of geomorphic unit which is often accompanied by a large number of geological defects: caves. In blasting engineering, if there are karst caves around the blast-holes, it may result in higher boulder yield and the generation of flying rocks due to the change of burden which is very hazardous for the safety of surroundings. The models of rocks with karst caves from blasting holewere built by the software of ANSYS/LS-DYNA. The results of computation simulation show that thecave can increase more free surface for blasting and leads to a broken zone around itself. Thus rockmass around the cave will fly toward inside and it will result in undesirable result of whole rock mass to be blasted. In addition, the models of rocks with karst caves in different shapes were simulated and thecomputation results show that the caves in round shape have higher load resistance capability than that the caves in rectangle shape. All the simulation results can offer effective guidance for blasting design. The models of rocks with karst caves were built in different distances and shapes from blasting hole by the software of ANSYS/LS-DYNA. The effect of different karst caves on blasting stress and blastingresult were studied."

Jan 1, 2017

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Atsuo Inoue, Toshihiro Ogata, Hideaki Sugihara

Generally in Japan, since ANFO has easy handling and low-price, it is most used as industrial explosives. However, ANFO is very easy to dissolve in water, it is difficult to use under existence of water and the consumer have desired water-resistant ANFO which has perfect water resistance. Then, we have developed the Water-Resistant Granular Explosive (It is written as following WRGE.) in which the surface of the explosive was covered by waterproof film, so that WRGE is able to use in hole with water. We ran various performance tests about the WRGE developed in the laboratory. Consequently, WRGE has water resistance of over 6 hours, and it has been checked that a performance and handleability were equivalent to the conventional ANFO. Then, we carried out the field test in the consumption site, and did performance evaluation on an on-site level. As compared with ANFO, fragmentation (size and volume) and handleability are almost equivalent. However, some problems which the WRGE is not settled out smoothly in hole with water and need more time for loading were also clarified. We are going to continue some advanced improvements through field tests.

Jan 1, 2005

By Norman Paley, John Kells

The climate and location of the Red Dog Mine present several challenges to blasting operations. The mine is located north of 68º latitude, in an area of continuous permafrost. Ground temperatures are below freezing year-round and air temperatures range from -40 to 70°F (-40 to 20°C). Because there is no overland access to the mine, the entire year’s supply of bulk explosives, approximately 7,000,000lbs (3,175,000kg) is shipped in by barge during the 100 day shipping season when the port is ice-free. The first week in July is the earliest that new product arrives at the port. Emulsion usage is maximized from mid April through October when surface water fills the blastholes during drilling. This necessitates that a considerable portion of the bulk explosives are stored for 10 months or more before usage. The emulsion is routinely pumped from the ISO containers at temperatures of 20ºF (-7°C). The mine engineers conducted a testing program during the 2001-2 blasting season to identify the bulk explosives best suited for the conditions at the mine. A secondary goal was to decrease the usage of sensitized emulsion, as this is the most difficult portion of the explosives order to ship. To ensure repeatability when transferring the results to the day-to-day blasting operation, the majority of the testing was incorporated into normal blasting operations in the field. The mining methods used at Red Dog Mine make direct fragmentation analysis impractical and performance testing in the field relied primarily on VOD measurements. The products were also tested for their ability to be pumped in cold temperatures.

Jan 1, 2004

By Bill Rose, Alan Foster

This paper will outline blasting as undertaken at the Flour Mill project in the Georgetown area of Washington, D.C. It will discuss the vibration and blasting problems found in blasting in high risk and highly populated areas, and the day to day methods used to minimize damage potential and still maintain adequate fragmentation.

Jan 1, 1979

By Andrew Theobald, Peter Dare-Bryan, Trevor Byers

The use of advanced modelling techniques and the timing flexibility of electronic initiation systems allows for unprecedented control over blast outcomes as shown in several complex blasting problems experienced by the open pit operation Xstrata Ernest Henry Mine (EHM) in north-west Queensland, Australia.

Jan 1, 2010

By Lon Santis, David Leidel, John Tatom, Meredith Hardwick

This paper describes the development and methodology of the Institute of Makers of Explosives’ Safety Analysis for Risk (IMESAFR), a risk analysis software program for commercial explosives operations. IME is a nonprofit safety and security association devoted to the safe and secure manufacture, transportation, storage, and use or disposal of commercial explosives in the US and Canada since 1913. The software methodology’s basis is the U.S. Department of Defense Risk Based Explosives Safety Criteria Team’s Safety Assessment for Explosives Risk (SAFER) software. A diverse group of industry and government experts contributed to modifications to SAFER that reflect commercial operations. IMESAFR is intended to supplement the American Table of Distances (ATD) and offer standardized methods of managing risk from a wide variety of commercial explosives operations where the ATD does not apply. The modifications made to SAFER primarily involved the addition of commercial activities and potential explosives sites (PES). A review of commercial explosives accidents and operations over the last 20 years served as the basis for establishing probability of event values. An industry survey of commercial PES types in the U.S. and Canada was conducted to identify and address critical differences in commercial structures as compared to the military structures in SAFER. The paper concludes with discussion of the potential uses for quantitative risk analysis (QRA) and a description of other explosion effects software

Jan 1, 2007

By Robert Hopler

Your petitioner further alleges that at various times, to wit, from 1872 until June 30, 1895, during the existence of the combination and conspiracy in restraint of trade among the various States herein- before described, there were organized under the laws of various of the several States of the Union various corporations having for their object the manufacture and shipment and sale of a high explosive commonly known as dynamite, which said explosive is commonly used for the same purposes as those for which blasting powder is used;

Jan 1, 2013

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011