Search Documents

By David Porter, Nathan Rouse

The implementation of presplit blasting has been widely utilized in open pit and underground tunneling. This case study works through the iterative process of developing a heading drill and blast design to control overbreak and limit backbreak in cut and fill headings. The initial design was based on rule of thumb parameters, and the design was then modified for the field conditions based on results. Throughout the design process the drill profile, explosive charge, and timing were modified to yield the best profile compared to design. Data collection during the design process was extensive to best understand the effect of modifying parameters, and gauge performance of design changes. Input from the miners as well as engineers was considered to allow for the best possible adaptation of the design change from existing practices. During the process resistance to change was realized and accounted for to understand the issues that the miners were facing and how to best address them while ensuring high quality blasting. Workforce buy- in was addressed by illustrating the long term benefits of higher quality blasting and the tradeoff of with a slightly more in depth drill and loading cycle.

Feb 6, 2023

By Adam T. Young

This paper will describe the process of using low density bulk emulsion as a means to maximize the production of an oversize or “rip rap” aggregate size range (8 inch to 72 inch) that the quarry customer has a market demand for. It will also discuss the pre-blast and post-blast metrics used during the product trials and evaluation.

Jan 1, 2017

By Italo Onederra, Miguel Araos

"In order to characterize non-ideal explosives, the explosives industry rely on unconfined velocity ofdetonation tests and where possible underwater pond tests. The information obtained from such tests isquite helpful, however it cannot tell us much about the dynamics of the detonation reaction process. The detonation process has been studied for ideal explosives and the reaction zone length have been measured. However, for non-ideal explosives, that type of information is not available. Therefore, the primary aim of this work was to capture the detonation process of a non-ideal explosive using high speed video camera to determine the zone length."

Jan 1, 2017

By Jhon Silva

"Signature Hole and Waveform Superposition techniques used to predict and control mine blast ground vibrations require a clearly defined information collection configuration. The collection of this information determines the scope and success of the ground vibration prediction. Application of the Improved Signature Hole technique using the Silva-Lusk equation requires the collection of at least two informational elements from any specific production shot. The first required element is a signature waveform, and the second element is the overall production blast waveform. The signature waveform depends on detonated charge variables such as the amount of explosive in use, use of decking, the possible detonation of several holes at the same delay, and many others. The production blast waveform is beneficial to the Improved Signature Hole methodology when used to calibrate the model, and toobtain accurate vibration predictions for different timing configurations."

Jan 1, 2017

By Koichi Kurokawa, Takeo Ueda, Masahi Nakano, Yoji Tasaki

A lightning strike generates several 10kA and several billion volts, and earth currents generated by lightning is dangerous to some underground and all surface blasting operations. In order to evaluate the safety against lightning in conventional electric firing method and electromagnetic induction blasting system, a test is conducted by connecting a wire with an impulse generator. Frequency of impulse current used in the test is 17kHz and the waveform is a vibration type and the duration time is 250 ~usec. The results of the test show that induced current increases with the increasing of impulse current. In the case of MBS connection, when maximum primary current is 1700A, Maximum secondary current is 11.8A and the electric detonator is fired at this condition.

Jan 1, 1988

By Frank Hirthammer

"Nowadays, security in the lifecycle of explosives is more important than ever. Terror attacks all over theworld pushed the EU to decree a Commission Directive for the identification and traceability of explosives that set a series of requirements for involved manufacturers, distributors and end-users. The challenge was to find and implement a track and trace system for all concerned European companies byApril 5, 2015. Since then, countries worldwide have followed this example and implemented similarregulations."

Jan 1, 2017

By Joel Chipana, Roberto Laredo, Benjamin Cebrian

Ring blasting is a common production method in underground metal mines. As a drill and blast process, it presents particular features that do not correspond with bench blasting in open pit or underground mining.

Jan 1, 2017

By Klaus G. Hinzen

Seismic observations offer the only possibility for remote sensing of physical processes like shock-front spreading, material crushing and ground movement. A better understanding of these processes will help to increase the economy of blasting. We developed a digital seismic monitoring system for research purposes. The system can simultaneously record up to 64 channels with a maximum sampling rate of 31 kHz per channel. A software package for rigorous analysis of blast induced seismic waves has been developed.

Jan 1, 1989

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By David Leidel, Beth Shimer, James Stuart

Periodically, the Institute of Makers of Explosives Safety Library Publications are reviewed, edited and updated to reflect recent technical developments, new commercial explosive products and new regulatory requirements. The rapid proliferation of electronic devices, particularly portable communication systems, inventory management devices, navigational aids, etc., required the revision of the IME Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators”. The new edition of SLP-20 has been updated to correct alterations to U.S. frequency allocations and maximum transmitted power permitted and a discussion of communications and tracking systems required in underground mining by the Miner Act. Also, an entire section was added dedicated to safe distances from RF sources to the special type of resistorized electric detonators used in the upstream oil and gas industry on wellsites and an enlarged section describing the particular types of RF sources that the blaster may encounter, perhaps in construction blasting operations.

Jan 1, 2012

By Tom BoBo, Seth Gering, Jeff Loeb

Presenting a D&B feedback loop built on a well-designed blast, proven fragmentation analysis and blast monitoring solutions, underpinned by technology that not only increases profit from every blast, but also increases a mine’s purchasing power over one of the most expensive part of the process – explosives.

Feb 1, 2020

By Andreas Gaich

A new 3D fragmentation analysis method for muck piles is presented. It works with aerial imagery from UAVs (drones) and handles entire muck piles with minimum user intervention.

Feb 1, 2020

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By David Harrison, Brian Harrison

The Army Corps of Engineers completed the Charleroi Lock and Dam in 1932. It is located on the Monongahela river approximately 22 miles (35k) south of Pittsburgh in Charleroi, Pennsylvania. It is comprised of a 420-foot (128m) gated dam, and a 720-foot (219m) by 56-foot (17m) land side lock, which provides for a 16.6 foot (5m) vertical lift.

Jan 1, 2018

By Stewart A. Silling, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

GEM (Geologic Element Motion) is a Distinct Element Method (DEM) for modeling blast-induced heave. It was developed with a very fast computational algorithm that efficiently treats many different element shapes utilizing alternating arcs and lines to create GEM elements. The GEM computational technique has been previously documented so only a summary will be included in this paper. New features of GEM are the ability to define the size of the rounded corner radius as well the length of the sides for quadrilateral and hexahedral elements. Circles can be created from a quadrilateral element with zero length sides and four arcs. An additional new GEM feature is energy partitioning between brisance and heave. This physics-based partitioning is essential for accurate modeling of blast results over a wide range of rock and explosive types. It accurately defines the volumetric, pressure and energy state of the explosive gases in a blasthole following detonation. Rock mechanical properties and explosive characteristics are included in the calculations. Example simulations provide comparison of the GEM predicted heave for two different classes of explosive. A GEM simulation utilizing hexahedral elements is compared with previous modeling incorporating circular elements.

Feb 6, 2023

By Robert Hopler

Although electrical instruments were being widely introduced into the study of seismic tremors, attempts to understand and quantify shocks from blasting continued to use rather primitive methods well into the 19th century.

Jan 1, 2007

By Scott G. Giltner, Alex Schwenk

An iron operation sought to extend the life of the mine by conducting a major pit pushback in an area close to several public structures and the neighboring town. The result of the pushback would make millions of tonnes of ore available for mining allowing many additional years of taconite mining. This paper discusses the initial development blasts conducted for the pit pushback. For the development blasts, it was determined that no fly rock should leave the mine site and that the blast vibrations should be as low as possible, but specifically under 19 mm/s (0.75 in/s) at a nearby sewage treatment plant. One issue complicating the blast design was the variation in hole depth within any given blast. For the initial sinking shot, the hole depths varied from 6.4 m (21 ft) to 12.5 m (41 ft). In the subsequent blasts the hole depths within each blast could vary up to 5.8 m (19 ft). Various tools were employed to design the blasts to ensure there was no fly rock and that the blast vibrations were as low as possible. UAV surveys of the blast areas were conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. In addition, signature hole analysis was performed for each blast to determine the optimum delay time that balanced the need for minimal vibration, prevent fly rock, and a well fragmented muck pile. Electronic detonators were applied to achieve the necessary control of the blast that balances these three concerns. The results of the seven blasts conducted to date provided the desired results. The peak vibration level at the sewage treatment plant for the seven blasts was 10 mm/s (0.40 in/s). The only fly rock occurred when there was a miscommunication in the blast design resulting in under burdened holes on the front row. To date, the mine has been able to safely expand the pit into an area that will add many years to the mine life. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By Randall M. Wheeler

Pre-blast surveys are used to document the condition of a structure prior to the commencement of blasting activities. They provide the best means of determining the pre-existence of visible cracking and deterioration in a structure before blasting is initiated. A small investment in a good pre-blast survey, coupled with good public relations, could mean a large cost savings for a company in the future.

Jan 1, 1992

By Jacob Miller, Phillip Mulligan

"Measuring the blast pressure associated with an explosion suspended above the ground (Free Air Burst)is a common research objective in Explosive Engineering. Theoretically, the shockwave from a Free Air Burst (FAB) configuration expands radially and the shockwave is assumed to have a smooth (uniform) shock front. The way in which the FAB explosive charge is suspended, packed, and the charge geometry can affect the shockwave expansion. These factors can generate a non-uniform shock front. As the scaled distance between the pressure sensor and the FAB increases, the shockwave expansion averagesnon-uniformities into a uniform shock front, at which point the FAB suspension system becomes less critical than when the scaled distance is “close-in” (Z <3)."

Jan 1, 2017