Search Documents

By M. Kargar Razi

According to the unique properties and many applications of nano gold powder, it was prepared from an acid leaching tail solution. The low value residual gold ions were existed in acid leaching tail solution in Mouteh gold mine in Iran with fellow heavy metals as pollutants (FeP2+P, Cu P2+P, and ZnP2+P). Preparation of nano gold particles is achieved by two steps. First, by addition of ammonia as separation step and second using suitable reagents for precipitation/extraction step. Conditions control includes pH, residence time, temperature, agitation, and molar ratio of reducing agents to reagents. The optimum results show that nano gold powder was prepared by temperature of 250 °C, urea to gold molar ratio of 3:1, and reduction time of 20 min. Also, heat treatment improves dispersion of nano sized gold particles. The properties of gold nano powders were evaluated by SEM, A.A, and UV- Vis spectroscopy methods. The size of prepared particles were about 80nm to 90nm.

Jan 1, 2014

By Tilak Raj Mankhand, Mudila Dhanunjaya Rao, Kamalesh K. Singh

"Zinc dust is used for the removal of primary impurities by cementation from the zinc sulphate electrolyte before electrowinning of zinc. However, the industrial zinc electrowinning plants has been reported that the zinc dust consumption is in large excess than the stoichiometric requirement. In the present investigation, morphology of the zinc dust has been altered by ball milling and utilized for the cementation of cadmium, which is one of the major impurity and compared the change in the rate of cementation with original zinc dust. Initially, 325 mesh size zinc dust was used for the optimization of the excess quantity of zinc dust to be used at a temperature of 50 °C. The chemical analysis of zinc dust before and after ball milling and morphology were studied by scanning electron microscopy (SEM), and the solution was characterized by Atomic Absorption Spectrophotometer. The rate of cementation increased with increase in ball milling time. The residual precipitate obtained after filtration was also characterized by X-ray diffraction analysis. Finally experiments were conducted to study the effect of temperature and kinetics of cadmium cementation using first order reaction kinetics. Based on the integral method, the calculated activation energy for the cadmium cementation with 4-hours ball milled zinc dust was found to be 3.39 KJ/mole. INTRODUCTION Primary production of zinc in the world is carried out by hydrometallurgical route. The primary impurities in the neutralized zinc sulphate solution that cause negative effect on electrowinning are copper, cadmium, cobalt, and nickel. Copper diminishes the current efficiency and cadmium contaminates the cathode zinc (Morgan, 1977) while electro winning. Nickel and cobalt lead to perforation in the zinc deposit and prevents the electro winning process (Abrasheva et al, 1984). Due to higher electro positivity of these metal impurities than zinc, they can co-deposit with cathode zinc at the time of electrolysis. In addition to that, some possible impurities (including cobalt) in the electrolysis may lower the hydrogen overvoltage, allowing deposition of hydrogen at cathode resulting in fall of current efficiency. The deposition of zinc on the cathode is possible only at higher hydrogen overvoltage which is practicable in the absence of such impurities (Raghavan et al., 1999). Cementation is one of the prominent purification technique, and in that less reactive metal can be replaced by highly reactive metal by allowing them into precipitation. Cementation of cadmium from zinc sulphate electrolyte is being done by the addition of zinc dust."

Jan 1, 2018

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By V. Hema

Granular materials are widely used in process industries, such as chemical, pharmaceutical, cement, food, detergents, and fertilizers. Mixing, blending, calcining, reduction, heating, and granulation of these materials are frequently carried out in rotating cylinders. In all of these processes, the mixing and segregation of these granular materials is important as this controls the secondary phenomena in the rotating kiln such as heat transfer to the material. A significant amount of work is available in the literature but to date these efforts have not been able to capture the important parameters affecting the mixing and segregation in rotating kilns. In addition, the range of parameter values studied so far is rather limited. Simulations of granular materials are based on either discrete elements or continuum models. The discrete element methods (DEM) combine semi-empirical models for the inter particle interactions with the equations of motion from classical mechanics to simulate the explicit paths of all granules in a rotary kiln, thus yielding realistic predictions of the mixing process. This approach is very demanding computationally, which strongly limits the number of granules and the number of revolutions in a simulation. Continuum models dispense with the discrete particles and can therefore be scaled up more easily. But the constitutive relations that serve as the foundation for continuum modeling are difficult to come by, and often only applicable to specific systems and conditions. Here we have chosen DEM simulation for investigating the mixing and segregation behavior of granular materials in a rotating cylinder. This work is directed towards demonstrating the capability of the prediction of the mixing and segregation behavior of granular materials in a horizontal rotating cylinder through discrete element simulation. Further the effect of particle size and rotational velocity on the mixing and segregation behavior is investigated. The simulation results are quantified in terms of mixing index, mixing rate, segregation index and percolation index. Keywords: DEM simulation, granular mixing

Sep 1, 2012

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By N. R. Mandre

In the present work an attempt has been made to study beneficiation of low-grade iron ore associated with manganese clay by selective flocculation. The representative samples obtained for this purpose were initially subjected to chemical and mineralogical studies. The chemical analyses indicated 42.56 % Fe, 6.25% Mn, 8.72 % SiO2 and 13.60 % Al2O3 in the representative sample. The mineralogical analyses carried out under optical microscope showed that the ore mineral predominantly comprised of iron oxides and hydroxides along with manganese and silicate as gangue minerals. Prior to the beneficiation studies, the samples were subjected to settling tests. These tests were carried out by using poly acrylic acid (paa), poly acryl amide (pam) and guar gum (gg) as the flocculants. From these studies it was observed that settling rate of particles increases with increase in pH and a maximum settling rate of 0.23 cm/secwas obtained at pH 9 in presence of poly acryl amide. Further, the samples were subjected to selective flocculation studies using above-mentioned reagents. From these studies better results were obtained in the experiments carried out with poly acryl amide as the flocculant. Thus, it was possible to upgrade the iron content from 42.5 to 53%, with a recovery of 92%. However, 51% Fe with recovery of 87% and 50% Fe with recovery of 94 % was obtained using poly acrylic acid and guar gum respectively.

Sep 1, 2012

By A. K. Mukherjee

In this apparatus closed sized particles are placed in a container and then fluidized by passing water through the load of particles. Water flow is adjusted to deposit particles in one or more layers depending on the specific gravity of each of the particles, after which the deposited particles are separated in portions of different specific gravity. The obtained portions represent different ore content of the closed sized fraction. The process is repeated for all other size fractions to generate washability curve of the feed. Three different types of iron ores and one coal sample are tested in this equipment. The theoretical yield-grade curve generated for iron ore feed is unique in absence of any such practice for ore minerals. Similar curve is generated for coal and it is compared with washability curve, an existing practice followed worldwide. This comparison validates the performance of the process and the equipment.

Sep 1, 2012

By Swati Mohanty

Spiral concentrator, which works on the principle of gravity separation, is widely used in the mineral industries for separation of solid particles based on the size and density. In the present study, CFD simulation of the flow profile on a laboratory scale spiral concentrator of height 2.29 m, pitch 0.435 m and width 0.17m was carried out. A single computational domain covering the entire spiral was considered. Volume-of-Fluid algorithm was used to track the interface and predict the flow profile. In the present study the Donor-Acceptor method was used for the calculation of volume fraction in the cell. Simulation results show that the velocity increases as the water flows down due to the convective force and gravitational force, but the viscous force acting in the opposite direction retards the flow. Thus the maximum velocity is attained at turn three at which the viscous force overpowers the other forces and further down the velocity decreases. Measured water depths along the radius of the spiral at various heights were compared with simulated depths, which were in good agreement. The simulated liquid phase velocity profile was used to carry out preliminary studies on the flow profile of solid particles of size 500 micron and densities 2600kg/m3 and 5100kg/m3, based on the Lagrangian model taking into consideration fluid-particle interaction.

Sep 1, 2012

By I. A. S. Brum

Brazil has large reserves of coal (7 billion tons) located predominantly in the south of the country. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently the country's strategic planning aims to minimize the gap between coal and resources traditionally used in the Brazilian energy matrix. In this scenario, the processing of Brazilian coal in columns flotation appears as a promising alternative, having been successful in mineral systems containing fine particles. This paper aims to study the overall process of column flotation for a specific Brazilian coal. The material used in this study consists of fine coal that is usually discarded as waste and deposited in the tailings dams. The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The variables analyzed were the influence of size particle, solids concentration in the pulp, the concentration of surfactants and frothers to be used. The first results showed that it is possible, from a feed with around 65% of ashes, to obtain products with approximately 35% ashes with mass recoveries about 40%. Concentrations of frother (pine oil) ranged from 50 g/t to 300 g/t and the collector (diesel oil) of 50 g/t to 200 g/t. Keywords: column flotation, coal, tailings, negative bias

Sep 1, 2012

By Zhu Yangge, Zheng Guibing, Hu Xiaoxing

"Because of the similar crystal structure and surface properties, it is very difficult to realize the efficient separation of magnesite and dolomite by flotation, which is the main reason restricting the utilization of magnesite resources with dolomite symbiotic. To deal with a magnesite resources with high content of calcium impurity in northwest China, a novel decalcification technology by combining flotation with leaching is proposed in this paper. In flotation process, a novel flotation collector with good efficiency and low temperature resistance was developed, and the depression effect of sodium hexametaphosphate was investigated. In leaching process, the leaching rate difference of calcium and magnesium was observed. By industrial test, from the magnesite ore with MgO content of 43.96%,the grade and recovery of obtained concentrate ( calculated by MgO) are 47.28% and 67.68% respectively, at the same time, CaO content decreases from 3.91% to 0.30%, which means that more than 95% of CaO impurity is removed.INTRODUCTIONMagnesite is one of the main raw materials for the production of refractory materials, and it is widely used in metallurgy, chemicals, ceramic, construction and other industries. China is the most important supplier of highquality magnesite resources, accounting for about 60-70% of the world's identified supply of magnesite products is provide by China (Jewell, 2014). In recent years, high-quality magnesite ores can be directly used are going to run out in China, and the utilization of magnesite resources with high impurity content have drawn more attention.The main purpose of purification for magnesite is to remove SiO2 and CaO impurities which affects the strength of the refractory material. Flotation is the commonly used method to remove impurities in magnesite ore. Reverse flotation with cationic collector is usually adopted to remove silicon containing impurities, and a great deal of literature has been reported (Santana A. N. and Peres A. E. C., 2001; Wang and Sun, 2008; Zhu et al, 2014; Wu et al, 2015; Ivan B. et al, 2017). But when the major gangue component is dolomite, it is very difficult to realize the efficient separation due to the similar crystal structure and surface properties between magnesite and dolomite. To solve this problem, researches have studied the surface properties of magnesite and dolomite, such as wettability, electrical property, solubility and solution chemistry (Nermin and Nurgul, 2006; Nermin 2006; Ozbek and Abali, 1999; Lacin et al, 2005; Bayrak et al, 2006; Bakan et al, 2006; Chen G. and Tao D., 2004), but the commonly studied direct flotation using oleic acid as collector is still hard to receive an ideal effect."

Jan 1, 2018

By Alex Heath, Andrew Barycki, Baladron. Javier

"Efficient flocculation is important to thickener performance, affecting the overflow clarity, solids settling flux, underflow density and operability. Many factors affect flocculation; from the material/flocculant type, dilution of the feed and flocculant solution, mixing, to the shear rate and shear history. The flocculant addition point (or points) can be used as a tuning method to alter the effective flocculation time in a feedwell, with addition further up the feed pipe increasing the residence time but making the aggregates more prone to breakup if they experience high shear later in the process. Conversely, adding the flocculant later, eg under the feedwell shelf decreases the mixing time but allows some free (unadsorbed) flocculant to be available at the feedwell exit. An extensive trial has been performed on an operating thickener comparing seven individual different flocculant dosing positions through a Vane feedwell, and some combinations of two dosing points simultaneously. Measurements of the velocity, solids concentration and aggregate size were made throughout the feedwell at the different positions, with the dosing points significantly changing the aggregate size and clarity, and also affecting the solids concentration at some positions. The results are accessed in terms of flocculation kinetics and used as CFD validation data."

Jan 1, 2014

By M. F. He

The depression of pyrite in marmatite flotation by a new depressant Sodium Glycerine-xanthate (SGX) has been investigated through microflotation, zeta potential, and adsorption measurements in systems open to the atmosphere. The flotation tests of single mineral show that in the presence of SGX, marmatite can be activated by Cu2+ and shows good flotability, while pyrite can?t be activated and therefore shows poor flotability, as a result these two minerals can be separated using butyl xanthate as the collector. The depression mechanism of SGX on sulfide minerals is discussed based on Zeta potential and adsorption isotherm. Zeta potential experiments demonstrate that at the presence of Cu2+, SGX can strongly adsorb on the surface of pyrite, while it can?t adsorb on the surface of marmatite, thus the results are in accordance with those of flotation experiments; the results of adsorption isotherms show that the adsorption density of SGX on pyrite is greater.

Jan 1, 2014

By S. H. Shahcheraghi

The four operational parameters including collector dosage, frother dosage, conditioning time and pH, are the most important parameters effective on the flotation kinetic. The present study has been done at the Miduk Copper Complex in the province of Kerman. The effect of operational parameters on the flotation kinetic of copper minerals were studied and analyzed, so the optimum conditions for flotation kinetic of copper sulfide minerals were obtained. Under the obtained optimum operational conditions, the recovery of copper sulfide flotation at the 95% confidence level was estimated to be between 92.76% and 95.48% and the copper sulfide flotation kinetic constant was estimated to be between 1.40 and 1.45 min-1. Results showed that the consumption of the X231 collector (O-isopropyl-N-ethylthionocarbamate) and the A65 frother (Polypropylene glycol) could decrease up to 35% and 50% respectively while the copper sulfide recovery increases about 1 up to 2% at the laboratory scale. Keywords: flotation kinetics, sulfide copper, optimization, the Miduk Copper Complex, response surface method

Sep 1, 2012

By B. Aydin, G. Erturk, G. Bulut

Coal is a complex material because of its structure consisting of carbon constituents and mineral matter. Flotation is readily carried out due to hydrophobic characteristic of coal. Therefore coal flotation is the most commonly used technique for fine coal beneficiation in order to acquire clean coal separating ash forming mineral matter from carbonaceous matter. In the coal flotation, floatability of coal both depends on characteristic of coal and used flotation reagent. Frothers as a flotation reagent are used to facilitate air dispersion into fine bubbles by prevention of bubble coalescence in the pulp phase, and stabilization of flotation froths. In this study, the effects of frother types and concentrations at different pH and particle size on the coal flotation were investigated. The representative sample was taken from Zonguldak, Turkey. It contains 9.1% ash and 7313 (kcal/kg) calorific value. Pine oil, Dowfroth 250, MIBC and Isooctanol were tested as frother types. It is determined that 1.92 ppm frother concentration is sufficient to float coal, except pine oil. In mixed frother tests, it is seen that Dowfroth 250 is more effective than others. No significant difference in coal recovery was observed for flotation tests at the different pH values. The best results are obtained in size of coal (-0.1 mm) with all frothers.

Jan 1, 2014

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By C. Kleine

Coal sorting with an x-ray-transmission (XRT) sensor has experienced a lot of development since first described by Jekinson et.al. in 1974. Powerful computers and increasingly sensitive X-ray scintillation counters enabled the development of high-performance sensor-based sorting machines. The first industrial installation of a belt-type XRT-sorting for coal is in operation since 2004. It is upgrading high quality coal from 1% ash to 0.7% ash for cathode production. In comparison to the high quality coal which is treated with a belt-type sorter, the chute type sorter has been successfully optimized for high volume coal treatment of lower quality coals. This project was funded by the German Environmental Fund (Project Nr.244444). In cooperation with the RWTH Aachen University and Isambane Processing, CommodasUltrasort(now Tomra Sorting Solutions) conducted extensive pilot test work under production conditions in 2010 for the destoning of power station coal at Arnot Power Station in South Africa. The experience gained during this pilot test phase led to an optimized, redesigned PRO Secondary XRT Chute sorter which is now in operation at a South African coal mine. This flexible semi-mobile modular destoning plant is treating a size range of -120 mm +30 mm at a throughput of 150 tph. The implementation of this plant not only reduces the ash content, abrasiveness index and sulfur content significantly, but also reduces royalties, water treatment and transport costs.

Sep 1, 2012

By J. Lampke

The superior characteristics of iron ore pellets compared with natural ore and sinter are well known. Due to the higher grade and bulk density they show improved transport and material handling properties. While charging blast furnaces with pellets an increased productivity is realized through pellet?s uniform structure and composition. The increased productivity is caused by a high permeable furnace burden with a decreased coke usage via fuel injection and oxygen enrichment. Therefore, a narrow pellet size distribution and a minimum content -6.3 mm are necessary (Meyer, 1980). The required pellet size distribution can be achieved on the one hand by screening the fired pellets after the induration furnace and recycle the undersized pellets. On the other hand it is possible to produce high quality iron ore pellets with a high degree of sphericity, the important narrow grain size distribution ranging between 9 to 16 mm with high green strength directly in the pelletizing device. To produce high quality green pellets, possibilities and knowledge about adjustments of the pelletizing device are necessary. The paper presents a classification of state of the art pelletizing systems in accordance with the advantages of the pelletizing disc and pelletizing drum in issues like adjustability, green pellet quality, the recycling rate and the space requirement. By a systematization of the influences on pelletizing the common reliance of objectives on influence like pelletizing moisture, disc inclination, rotational speed, mass flow and rim height are given. A variety of industry-proven examples are shown, too. Keywords: Pellet, iron ore, pelletizing, pelletizing disc

Sep 1, 2012

By E. Kusaka, M. EL Salmawy

"The electrokinetic behavior of EL Maghara coal has been investigated in the presence of nonyl and octyl nonionic surfactants containing polyethoxy of different sizes with trade names of Triton-X100 (TX-100), Triton-X 705 (TX-705), Triton WR-1339 (TWR-1339) and Brij 58. The electrokinetic behavior was determined by zeta potential measurements. Zeta potential measurements were conducted by Laser-Doppler electrophoresis technique using zetamaster. The results show that the zeta potential of Egyptian coal varies with pH value, the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. It was found that the polymeric surfactants reduce the negative values of zeta potential of coal. The shift of PZC of coal upon deashing appears to be closely relevant to silicate mineral removal."

Jan 1, 2014

By F. Concha

A robust theory of sedimentation-consolidation evolved and was accepted by researchers world-wide in the last two decades of the 20th century. This theory provides a reliable method of thickener design and simulation. However, a process model, simple or sophisticated, empirical or phenomenological, is useful only if it is possible to determine, in an objective way, its experimental parameters. Research workers at the University of Concepción, together with Cettem Mineral Technology Center, created an integrated system of thickener design, simulation and control, including instrumentation, algorithm and software, which can be used by personnel in industry without specialized knowledge of thickening theory. In the paper, the development of three instruments for the measurement of pulp concentration, solid flux density and sediment compressibility is described. Each instrument uses software for data input, parameter calculation and results display. The paper also describes software for the optimization of the experimental parameter and for the design and simulation of industrial thickeners. Finally, mathematical algorithm and control strategies based on the phenomenological model are presented and compared with classical feedback control.

Jan 1, 2014

The ball level and pulp load play a key role in the operation of industrial scale ball mills. These two operating variables have a significant influence on the performance of the ball mill and any attempts to optimize these devices require manipulating either one or both of these variables. There are several models that can be employed to perform simulations to optimize the performance of industrial ball mills. However, most of these models require ball load and pulp load measurements as inputs to calibrate the model. The changes suggested by the simulator also provide operating regimes that involve moving either the ball level or pulp load and sometimes both of these variables. A ball mill model coded in JKSimMet was used in conjunction with the Sensomag to optimize the secondary ball mill at Waterval concentrator in South Africa. The results show that the perfect mixing ball mill model can be used in conjunction with the Sensomag to optimize the performance of the secondary ball mill.

Sep 1, 2012