Search Documents

By Leon Lorenzen, Charlene Gokhale

"In excess of 24 x 106 tons (Eskom, 1997) of coal-derived fly ash is produced annually in South Africa for the production of electric power. A large quantity of this ash is disposed of as a solid waste in landfills, thus posing a serious environmental problem. Due to the shortage of landfill sites, new ways of utilising fly ash are needed. Recently several authors have shown that various combustion fly ashes can be converted into zeolites to obtain industrial products with applicability in environmental management. Geopolymerisation has emerged during the last few years as a possible solution to some waste stabilisation and solidification problems. henolic compounds have been shown to be toxic to soil microorganisms at the parts-per-million level. Indeed several of the organic compounds classified by the U.S. Environmental Protection Agency as priority pollutants, are phenols. Immobilisation of phenols by adsorption on zeolites and encapsulation in a geopolymer appears to be a promising solution to this problem.This paper reports a technique for the production of a low-silica sodium zeolitic material from fly ash (zeolite NaP1), and its application for the stabilisation of phenols by adsorption and subsequent encapsulation in a geopolymer matrix. A commercial zeolite, clinoptilolite was also utilised as an adsorbent. Due to their uniform pore sizes and large surface areas, zeolitic materials are suitable for ion exchange and adsorption of certain organic substances. Adsorption data show that the commercial zeolite, clinoptilolite was an effective adsorbent for organics. Adsorption data showed that between 51.2 ppm and 74.3 ppm of chlorophenol or between 15.4 ppm and 32.5 ppm of phenol could be adsorbed. Physical encapsulation of the coated zeolite loaded with organic within a geopolymeric matrix increased the compressive strength of the matrix from 28.80 kN to 40.79 kN. Leaching data for the various geopolymer matrices with encapsulated and loaded zeolites show no organics being leached from the system at a detection level of 2ppm. According to the SABS these would have been acceptable organic concentrations within a waste water stream."

Jan 1, 2003

By L. M. Wang

Chengmenshan Copper Mine Concentrator adopts the new process of preferential?bulk stage floatation and utilize reground, largely increase the mineral processing index of the copper and the sulphide concentrates. In addition, the paper describes the remarkable economic benefit of the new process through the comparison of the new and the old processes.

Jan 1, 2014

By Jochen Petersen, David G. Dixon

"Although heap leaching may be perceived as a somewhat low-tech route for the extraction of low-grade minerals, the underlying physical, chemical and biological processes are in fact extremely complex. There has been increased interest in heap leaching of sulphide minerals in recent years with the advent of controlled bio-heap leaching, and the need to mine more marginal ore deposits.A detailed investigation into the dynamics of heap leach processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool, HeapSim. Some of the sub-processes that are modelled include mineral kinetics, particle size effects, bacterial growth, oxidation and adsorption, gas adsorption, pore diffusion, bulk advection, gas balance and heat conservation. The interplay of these various sub-processes is illustrated in the paper.Two case studies are presented which illustrate specific features of the model for different applications and how these have helped to identify key areas of concern. The first is focussed on chalcocite heap bioleaching, which shows that by nature of the reaction the process is strongly dependent on the initial supply of acid to the mineral site. In heaps this acid supply can be severely limited by the rate of diffusion from channels of flowing solution into stagnant zones of the heap, whereas in narrow-bore laboratory columns this effect is not observed."

Jan 1, 2003

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data – especially with semi-automated data acquisition by instrumented mine equipment. Much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together – in a single step. However, the success of the Mine to Mill ™ project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measured data and then to track performance from ore body model to saleable product and waste disposal.The path from resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is usually strongly focused on the technical requirements – not on the business model.This paper emphasises the difference between data and information. There is considerable potential for confusion between the two as both data and information are often expressed as numbers. For the purpose of this paper, data and information are distinguished by their uses.A data point (or datum) is a measurement. By way of contrast, information provides a basis for decision making."

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Ltd. Kyushu Metal Industry Co., Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

"Actually, the recovery of valuable metals such as iron, aluminium and copper is a nowadays practice in factories dealing with the processing of scrapped automobiles (Harder (WERG); Koga et al., 1997). This process has reach a recycling rate of about 75%, and generates a huge volume of waste (including cottons, sponge, plastics, rubber, etc…), locally known as “shredder dust”, which is commonly dumped on landfills; its recycling is either unsatisfactorily or not yet performed (Keller and Schebdat, 2000).The saturation and depletion of valuable disposal sites in the not-so-distant future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry.To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of a calibrated (–80+5mm) shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-weight materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively. A sedimentation tank is used to recover the light-weight materials deported in the heavy fraction stream."

Jan 1, 2003

Hydrofluoric acid (HF) is traditionally used in plant operation to separate feldspars from quartz. It acts during the conditioning step as a pH regulator and an activating agent providing an excellent selectivity. However, a corrosive chemical environment and the ecological impacts from the potential fluoride ion contamination are limiting factors to use this chemical agent at an industrial scale. Investigations of the amine-feldspar interactions in the absence and presence of non-linear long-chain alcohols were carried out on two ore samples. The presence of alcohol molecules led to form a closed packed layer only on the surface of feldspars. The highest order and packing at the feldspar surface were observed with a particular alkyl chain structure as Guerbert alcohols. A new flotation process was developed and tested at both lab and pilot scales on different feldspar ores. The Guerbert alcohols allow to perform a feldspar concentrate with very low content in quartz (2.3-3.5 %) and feldspars recovery from 78 to 81 % while the aliphatic isoalcohols show a more higher recovery level (88-89 %). New HF-free process is strongly dependent on the pH range (1.7-2.5) and sulphuric acid consumption during conditioning steps. Optimal amine/alcohol weight ratio is ranged between 0.8 and 1.0. The values below 0.8 decrease strongly the flotation selectivity and the quartz recovery within the feldspar concentrates is higher than that occurs with HF.

Sep 1, 2012

By Gerke Gilian, Pretz Thomas, Pehlken Alexandra

"The evaluation of health hazards within the treatment of mineral and waste materials is gaining more and more importance in industrial countries. The need to control occupational safety has been recognised, and regulations which describe general protective measurements for personnel provide a tool to protect their health. It is the aim of the paper to give an outlook for practical approaches to risk assessment and to present measures for exposure reduction in accordance with the state of the art in Germany.Both the treatment of minerals and of waste materials are described in relation to the risk assessment. The method of evaluating health hazards in the two industries is similar and therefore both examples are presented next to each other.The example presented in the paper is the German “Biostoffverordnung” (the regulation for biological materials) which is important for the waste treatment industry. All kinds of waste treatment facilities (like composting facilities, waste dumps, sorting facilities for packaging materials) are obliged to carry out an assessment of health hazards for a variety of working areas and working places. The possible safety requirements deriving from this regulation are presented and discussed under the aspect of biological hazards.All over the world each country has different guidelines and regulations but all have one target in common – to protect the employees. This can be achieved through a good management system of occupational health and safety. Therefore the health hazards have to be known and assessed.Principles of the assessment of health hazards are described through:Data collection on siteData evaluationAssessment of health hazardsDocumentation"

Jan 1, 2003

By Stoyan N. Groudev, Ioannis Paspaliaris, Plamen S. Georgiev, Irena I. Spasova, Kostas Komnitsas

"The uranium deposit Curilo located in Western Bulgaria for a long period of time was a site of intensive mining activities including both the open-pit and underground mining techniques as well as in situ leaching of uranium. The ore was rich in pyrite and, apart from uranium, contained some non-ferrous metals. The mining operations in the deposit were ended in 1990 but since that time the deposit is a permanent source of acid drainage waters. The generation of these waters is connected mainly with the oxidation of pyrite and other sulphide minerals by the indigenous acidophilic chemolithotrophic bacteria.Laboratory and pilot-scale studies revealed that an efficient clean-up of the above-mentioned waters was achieved by means of passive systems of the wetland type. In 2001 a wetland was constructed in the deposit to treat a portion of the acid drainage waters which were discharged to a small ravine. This ravine reaches into the Teina, a small river that is a tributary of the upper reaches of the Iskar river.The wetland was constructed in the ravine and its bottom was located on intrusive rocks with a very low permeability. The rocks were covered by a 30 – 50 cm layer consisting of a mixture of soil, plant compost and crushed limestone. The wetland was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Carex and Poa as well as different algae were also well present.The acid drainage waters treated by the wetland had a pH in the range of about 2.5 – 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The watercourse through the wetland covered a distance of about 0.2 – 1.0 l/s."

Jan 1, 2003

By Peter Riccio

Oxiana Sepon?s mineral processing facility in south central Laos produces copper cathode using leach-autoclave-SX/EW flotation technology. Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid for the leach circuit. However, low pyrite recovery has been an ongoing challenge in the flotation circuit. Tailings characterization work done by Ian Wark Research Institute showed that the pyrite losses to the tail are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines. In December of 2005, a joint Cytec-Oxiana technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt, and was un-available for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the Sepon low pH, high dissolved metal ion environment, and will not complex with ferric, ferrous, or copper in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which then was followed by on plant testing that showed a step wise improvement in pyrite recovery.

Jan 1, 2014

By Briony C. Ruse, David V. Boger, Fiona Sofra1

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.As environmental factors translate into economic issues, minimising waste production using dry disposal methods is gaining popularity. The use of rheological information is of high importance in evaluating the spreading characteristics, the transportation and the dewatering of thickened mineral tailings. The principles outlined may be applied to many industries encompassing a wide range of waste materials. The main obstacle to the widespread implementation of dry disposal methods has been the high initial capital cost of the methods due to the dewatering step, and the high cost of pumping thick suspensions across any great distance. Proper and thorough costing of tailings disposal activities combined with an accounting approach that shows closure and post-closure care costs on a per tonne basis of tailings disposed throughout the life of the tailings facility will show that dry disposal methods are more favourable than they might seem on initial appraisal."

Jan 1, 2003

By G. Belardi, N. Shehu, L. Passeri

"This paper illustrates the possibilities of applying what is essentially a physical soil-washing technique for treatment of soil contaminated by semi-volatile hydrocarbons in order to reduce the level of pollution to that permitted by Italian regulations.The ground around a factory producing lubricating-oil additives consists of silty-sandy soils which have long been contaminated by heavy hydrocarbons, especially branched alkyl benzenes and naphthalene derivatives. Pollution is particularly marked in some zones (hot-spots) where Total Petroleum Hydrocarbon (TPH) values are as high as 7000 ppm. The hydrogeological characterization showed the presence of a gravely soil in a sandy/silty matrix, with big stones making preferential paths to the water circulation. The permeability is 10-5 m/s and the water-table occurs at about 3 m below ground level.After laboratory and pilot-scale studies on representative samples of in-situ soils with TPH between 2700 and 7000 ppm a flow-sheet is proposed for reducing TPH values below the acceptable limits in Italy, namely 700 ppm for hydrocarbons with more than 12 carbon atoms and less than 250 ppm for those with fewer.On the basis of indications provided by laboratory tests a mainly physical treatment process of soil washing has been developed. This is used to clean-up soil from a site polluted by non-volatile hydrocarbons with a high TPH value. The process involves a high-density attrition stage followed by wet screening at 0.5 mm and then wet-gravity separation of the minus 0.5 mm fraction in the centrifugal field.The gravity separation products consist of a light fraction with particle size finer than 15 micron which contains most of the pollutants, and a heavy coarse fraction with TPH values conforming to the limits set by Italian regulations (less than 700 ppm hydrocarbons whose structure contains more than 12 C atoms, and less than 250 ppm of hydrocarbons with less than 12 C atoms)."

Jan 1, 2003

By Rong Fan, Andrea Gerson

"The small recovery of Ag, often in the order of 50%, by traditional flotation and leaching process strategies is closely related to the complicated and heterogeneous nature of Ag-bearing minerals with Ag typically being associated with numerous minerals within any given ore-body. Moreover, grain sizes may be extremely fine with micron-scale common. In order to design cost-effective Ag-bearing mineral flotation and leach recovery strategies it is firstly necessary to characterise the speciation of Ag and its correlation with other elements, e.g., Cu, As and Sb, within the ore matrix and process streams. The traditional QEM-SCAN analytical approach can prove problematic for some mineralogies due to difficulties in recognising degrees of crystallinity, polymorphs, complex solid solution series, high value trace element mineralogy, very fine grained materials; and the requirement for a comprehensive data base. Moreover, there is difficulty ‘seeing’ either surface films or surface contaminants which can both lead to poor flotation performance. There is therefore clearly a need to develop confirmatory and complementary approaches when these uncertainties arise. Synchrotron X-ray microprobe analysis provides a powerful tool for the mineralogical characterisation of finely segregated heterogeneous Ag-containing materials. These measurements enable comprehensive characterisation of the Ag-bearing components using synchrotron microprobe X-ray fluorescence mapping (µ-XFM), X-ray diffraction (µ-XRD) and X-ray absorption spectroscopy (µ-XAS). Further analytical strength is provided by principal component analysis of laboratory ToF-SIMS data which enables the statistical identification of correlated surface species enabling examination of surface chemical characteristics responsible for mis-reporting of Ag containing components within flotation streams. We describe the application of these techniques to a selected Ag-containing feed and tail and demonstrate how these compliment and extend traditional analytical methodologies."

Jan 1, 2014

By G. Atesok

Turkey?s EU affairs started in 1963 with the Ankara Treaty. On 31 December 1995 the Customs Union between Turkey and the European Union came into effect. In order to achieve the Copenhagen Criteria?s, Turkey, made laws parallel to the Framework Programs. On 3 October 2005, with the confirmation of ?Membership Framework Document? the negotiation process of Turkey has started. Coal had important role in the industrialization of EU and it is directly related to Energy and Environmental subjects. In this point many restriction became with the some protocols, in last decades. European Union composed Energy and Coal Policy, therefore engaged to reduce the emissions, and made new regulations. This regulations concern Turkey?s energy future, since large; but low quality of lignite reserves of Turkey, it is expected to have some difficulties with Union?s Environmental Legislation during Turkey?s congruity process. With the last natural gas import agreements of Turkey, the production and consumption of coal sunk in last seven years. However, considering environmental sustainability, the role of coal in energy production will rise up in the coming future. In this paper, in terms of Turkey Energy Sector, production and consumption problems of coal discussed and evaluated considering EU?s coal, energy and environmental rudiments.

Jan 1, 2014

By David Verrelli, Melissa Kistner, Leanne Smith, Chris Aldrich, Lidia Auret, Warren Bruckard

In this investigation, different mixtures of realgar and orpiment particles were floated in a laboratory batch flotation cell and multivariate image analysis was used to estimate the arsenic content in the froths. The analysis was based on the froth colour, as well as extraction of three groups of textural features, namely those based on grey level co-occurrence matrices (GLCMs), wavelets and local binary patterns (LBPs). Collectively, these features provided better information on the arsenic content of the froths than any one of the individual groups of features. Partial least squares models could explain approximately 78% of the variance in the arsenic by using all the features combined. The colour content, particularly the green component in the red-green-blue (RGB) features, provided almost as much information as each of the three sets of texture-base features individually.

Jan 1, 2014

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By V Radmehr

Ammonia and Amonium salts have been recognized as effective leaching agents in hydrometallurgical processes due to low toxicity and cost, easy recovery and high selective recovery of metals. New research findings of considerable advantages of leaching by these agents and elimination of problems associated with acid leaching has resulted in a new approach in the world to this method. The investigations in this field indicate more frequent use of this method for extracting copper from ore and concentrate relative to other basic metals. In this paper, we have attempted to describe the basis and different ammonia leaching methods and present the major research activities in this field for copper. We have also presented the latest findings and related novel processes. Comparative assessment of advantages and disadvantages of this method relative to acid leaching method, kinetic study of copper ammonia leaching and evaluation of Eh-pH diagrams in a system containing water and ammonia are other parts of our study. Finally, by describing the studies on copper extraction from the resulting pregnant solutions, the applicable extraction agents have been reviewed.

Sep 1, 2012

By Carsten Gerold

The paper is giving an overview about successful operating Loesche Vertical ? Roller ? Mills (VRM) installations and summarises the main benefits of the dry compressive Loesche grinding technologies in Airflow- and Overflow-Mode. Some of these benefits are optimised energy efficiency of the grinding - classifying - circuits, increased mineral recoveries and decreased OPEX costs, at a parallel simplification of the process route. Within this paper the process values of the Loesche VRM are compared to existing or planned conventional grinding ? classifying circuits. Further advantages discovered in pilot trials and examples for new more efficient process route alternatives are given. The paper reports about production and pilot trial experiences obtained by crushing and grinding Iron Ore, Iron Ore Concentrates, Copper Shale, Copper Matte, Copper Slag, Titanium Slag, Tin Slag, Steel and Stainless Steel Slag with Loesche VRM.

Sep 1, 2012

By C. A. C. Sequeira, G. N. Anastassakis

Electrochemical processes occur on nano-, micro- and macro- scale in numerous applications such as fuel cells, batteries, hydrogen production, mineral extraction, water treatment, electrotherapy, sensors and many others. In most of these applications, gases evolve either at one or both electrodes due to electrolysis. These gases form bubbles play a crucial role in electrochemical systems. For example, in electrowinning (EW) that is used to extract and refine metals such as Cu, Zn, Ni, Mn, and Cd from their solutions, in most cases the solution is acidic and oxidation of water molecules at the anode is the common counter reaction, which results in the liberation of oxygen bubbles. This generally requires a high overpotential and accounts for a considerable percentage of the energy consumed in metal EW electrolytic cells, apart from producing acid mist that is very corrosive for other cell equipment and building structures. The behaviour of bubbles in electrochemical systems is still a complex challenging topic which requires a better understanding of gas bubbles hydrodynamics and their interactions with electrode surface and bulk liquid, as well as between the bubbles themselves. The objective of the current paper is to briefly review the fundamental hydrodynamics of both gas bubbles on the electrode surface and gas bubbles interaction with the liquid bulk solution. The current work also investigates the impact of gas bubbling and some operating parameters in copper EW, such as current density (100-500 A/m2), temperature (25-75ºC), acidity (50-300 g/L) and a typical chemical mist suppressant (<50 ppm). The results clearly show that both suppressant and temperature reduced the overall surface tension of the solution. Also, chloride concentration and applied current improved electrolyte flow and copper quality at higher current densities. The current paper contributes to the development of mineral processing (specifically to copper hydrometallurgy), as it deals with fundamental hydrodynamics and interactions of gas bubbles that formed during copper EW and play a crucial role in copper electrochemical systems.

Jan 1, 2018

By Wei Sun, Ruolin Wang, Jianjun Wang, Xiaodong Li, Honghu Tang, Yuehua Hu, Anh V. Nguyen, Haisheng Han, Kefeng Chen, Zhao Wei

It is difficult to separate scheelite especially from fluorite with fatty acid collectors because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface. A simplified flotation process using Pb-BHA complexes was developed to replace the energy-inefficient Petrov’s process of using a fatty acid, increasing the recovery of scheelite and reducing the cost. The relationship between surface chemical properties (crystal chemistry, solubility, and Zeta potential) of minerals and flotation by using a fatty acid or Pb-BHA complexes was studied in detail to provide new insights into the selective separation mechanism. The results indicate that the scheelite surface exposes more O atoms than Ca and that they are negatively charged due to the anisometric dissolution of Ca and WO4, which provides the possibility for separation using selective interfacial reaction. The FTIR and Zeta potential results indicate that both chemical and electrostatic adsorption play an important role in the adsorption of Pb-BHA complexes on the scheelite surface. The XPS results of the atomic composition and binding energies confirmed the presence of the adsorbed Pb-BHA complexes and that O and Ca may be the active adsorption sites. Therefore, scheelite was able to be collected by forming either a Ca-O-Pbcollector or W-O-Pb-collector (BHA). However, fluorite was only able to be collected by a fatty acid collector and colloidal [H2SiO3]n -, and a high temperature was needed improve the selective desorption of the adsorbed fatty acid collector by forming Ca-[H2SiO3]n - on the fluorite surface, resulting in serious problems in industry. However, the Pb-BHA complexes significantly contribute to improving the recovery of scheelite minerals, simplifying the flotation process, and circulation of the residual reagents and water. The new process has been applied in Shizhuyuan Mine, and improved the recovery by almost 10%.

Jan 1, 2018

By Lev Filippov, Vyacheslav Severov, Inna Filippova

"Reverse cationic flotation is a very efficient method of beneficiation of oxidized iron ores when you need to separate hematite and quartz. This method can be also applied to reduce silica content in the magnetite concentrates obtained by wet low-intensity magnetic separation. However, cationic flotation in this case is less effective due to the presence of Fe-Mg-Al-bearing silicates as amphiboles in magnetite ores. These silicates are concentrated in magnetic products and determine the difficulties of their separation from iron oxides when amines and starches are used as collectors and depressants, respectively. The recalculation of the results of the electron microprobe analysis of three calcic Fe-Mg-Al-bearing amphiboles used to characterize cation distributions in structural units and to obtain structural formulas in accord with stoichiometric limits was conducted. The Mössbauer spectroscopy was used to examine the validity of the empirical estimation of cation distributions in amphiboles. The studied samples are metamorphic pargasite and ferrotschermakite and volcanic magnesiohornblende. The crystallographic analyses of the amphibole samples exhibited their heterogeneous surfaces explaining worse floatability of amphiboles with dodecylamine at pH 10. The electrokinetic measurements showed that the position of the isoelectric point of amphiboles is related to a substitution of Al3+ for Si4+ in tetrahedral sites and to an amount of Mg2+ cations in octahedral sites. Thus, the dodecylamine adsorption onto amphiboles through electrostatic interactions is mainly affected by a distribution of these cations in tetrahedral and octahedral sites of amphiboles. In addition, the effect of starch on the depression of Fe-Mg-Al-bearing amphiboles during flotation can be attributed to the presence of metal ions on the amphibole surface, which are capable of forming strong chemical complexes with starch molecules."

Jan 1, 2014