Search Documents

By Yagmur Sirinyurt, Ayhan Ali Sirkeci, Gülay Bulut, Mustafa Özer, Tuncer Acar

"The basic requirement of glass industry for the silica sand is at least 99% SiO2 content. On the other hand, coloring impurities such as Fe and Ti, must be removed. Flotation is the most widely used method for the purification of silica sands from impurities. In this study experimental studies were carried out to reduce Fe content of Mersin (Turkey) district silica sands by flotation. Silica sand sample with a d80 particle size of 1.85 mm was reduced below 0.5 mm in size. Then the size fraction -0.5 +0.106 mm was subjected to flotation tests. In flotation tests, sulfonate-type R801-R825, fatty acid based DER NA 7 (Produced by a Turkish company) and HA110-HA150 a blend of various chemicals produced by Mersin Cam-Is Mining Company (producer of glass raw materials) were used as collectors. Flotation tests showed that sulfonate type R801-R825 collectors provided much better results in acidic medium (pH: 3). The optimum pH value for DER NA, HA150 and HA110 collectors was found to be 7. It was observed that the addition of collector at once caused an increase in the amount of floated product that resulted in a loss of silica to the tailings. In the case of multistage addition of the collector much better selectivity was achieved. As a result of flotation tests conducted under best conditions, a concentrate assaying 0.046% Fe was obtained with a weight percentage of 93.4 when DER NA 7 was used as a collector. In the case of R801-R825 a concentrate was produced with 0.058% Fe content with a yield of 98.4%. On the use of HA150-HA110 the concentrate was produced with 96% weight recovery and 0.052% Fe content."

Jan 1, 2014

By R. Hejazi, Saghaeian. M., H. Abedini

Continuous vacuum belt filters mainly carry out an important duty in the solid-liquid separation processes such as iron ore concentrate dewatering. However as the particles become finer, the resistance to filtration and dewatering would increase and as the result cake moisture content tends to increase. So in recent decades, using additives in order to improve the filtration performance has been considered by many researchers. In the present study, the effect of several surfactants on the filtration rate and cake moisture content of Chadormalu iron ore concentrate (80% =40 micron) was investigated using a laboratory scale vacuum filter. The results of several tests indicated that a non-ionic surfactant (Lauryl Alcohol Ethoxylated, LAE) has the best performance on reducing the moisture content of the cake and reducing the cake formation time. The optimum dose of LAE was found to be 300 g/ton which reduced the concentrate cake moisture content from 13.76 to 11.28% (wet weight base). Some industrial filtration tests were performed in Chadormalu iron ore concentrate plant to prove the effectiveness of this surfactant. The surfactant is mixed with water and added to the concentrate slurry before distributing on the vacuum belt filter. The industrial and experimental results were almost similar, so that adding about 300 g/ton of LAE would reduce the final cake moisture content from 12.87 to 10.76%.

Jan 1, 2014

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By Vasily V. Lodeischikov, Adolf F. Panchenko, Olga D. Khmelnitskaya, Vladimir E. Dementyev

Pilot plant tests of underground gold leaching from Maminskoye deposit oxide ores at a grade of 0,7 g/t Au were carried out. The underground leaching flow sheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution on active carbon, carbon concentrate ashing and calcine melting to produce high grade gold concentrate. The underground leaching system throughput was 15 m3 of solution per hour. Gold concentration in pregnant solutions was 0.12-0.13 mg/l. Gold recovery from solutions into carbon was in the range of 63-84%. It was demonstrated that the low Au recovery in the adsorption cycle was due to the presence in pregnant solutions of "active" chlorine, which destroys active carbon and causes a sharp decrease of the carbon loading capacity for gold. To improve the adsorption indices, previously dechlorinated pregnant solutions using bituminous coal or Na2S2O3, is recommended. Ion exchange process was tested as an alternative for gold extraction from dechlorinated solutions. In the testwork period, 4.4 kg of gold were produced with a chlorine consumption of 3.5 kg per 1 g of gold. During the tests a program of environmental protection measures was completed to provide the necessary safety precautions of the underground leaching works.

Jan 1, 2003

By F. O. Milovich, V. A. Ignatkina, L. A. Samatova, E. D. Shepeta

"The aim of the research was to increase technological parameters of the flotation of finely disseminated scheelitecarbonate ore using selective reagent regime.In the studies the monomineral fractions of scheelite and calcite; samples of the scheelite-carbonate ore of the Primorsky deposit with the range of the carbonate module 3-65 were used. A carbonate module of ore is the ratio an initial assay of calcite to an initial assay of scheelite. Sodium oleate, iso-decyl alcohol, water glass, calcium chloride, soda or sodium hydroxide as flotation reagents were used. The flotation method in the Hallimond tube and in a mechanical cell, an adsorption method for study the kinetics of adsorption of oleate and isodecyl alcohol and its combinations on scheelite and calcite, IR spectroscopy including ATR to study the composition of surfacecompounds were applied. Selective reagent regime may include two ways - a combination of collectors or a modification of depressants of calcite and other gangue minerals. On one hand the combination of sodium oleate and higher fatty iso-alcohols of fractions C12-C16 in the rough scheelite flotation to reduce the flotation activity of calcite has been studied. On the other hand depression of calcite flotation by calcium chloride with water glass into rough flotation was used; modified the steaming cycle by Petrov's method applying change the concentration of water glass and other. Fatty iso-alcohols can adsorb on the surface of the calcite that reducing the adsorption of sodium oleate and floatability of calcite has been fallen. Their co-adsorbing with oleat on the scheelite surface were support the hydrophobization and flocculation of slime particles of scheelite. Flocculation of the particles of scheelite leads to increased up 3 times of the recovery of scheelite from the slime class, and calcite change up only 1.4-1.1 times it’s recovery.The growth of the carbonate module more than 11 is decreased the assay of WO3 in the scheelite concentrate of selection cycle."

Jan 1, 2018

By Megan Becker, Cyril O’Connor, Jenny Wiese, Gaynor Yorath

The effect of particle shape on true flotation has been widely reported. The present paper presents results obtained in investigating the effect of particle shape on the entrainment of particles during the flotation process. Different hydrophilic minerals with particles of varying aspect ratios were used and their shape determined using rheological tests and QEMSCAN. Their entrainment properties showed a close relationship to their shape with the recovery due to entrainment increasing as the aspect ratio of the particles increased. The effect of surface charge, by changing pH, and size of particles showed that the effect of shape was sustained at different pHs and particle sizes. Proposals are made to explain these observations in terms of the known relationships between drag coefficients and terminal velocities and shape. Since it has been previously reported that different milling procedures can affect particle shape, these results indicate that it is possible that such different procedures may result in increased entrainment of hydrophilic minerals.

Jan 1, 2014

By A. Otsuki

This paper describes the evaluation method of dispersion and coagulation of silica nano-particles by means of interactive force apparatus. The apparatus measures the size of fine particles in aqueous solution or organic solvent of high concentration and/or low optical transparency. Other conventional apparatus for size measurements (such as, apparatus utilizing dynamic light scattering) are difficult to measure the size of particles in such conditions accurately, due to multi-scattering of light in the sample solution or solvent. The apparatus measures the interactive force between two surfaces, i.e. the gold-coated glass hemisphere and the brass flat plate, (which is fixed at the bottom of the sample cell). The apparatus has three parts, i.e. main part (which consists of electric balance, hemisphere and flat plate), control part (i.e. personal computer, piezo-stage controller and voltage supplier), and detecting part (i.e. multi-meter and oscilloscope). During the measurement, electric field is applied between the hemisphere and flat plate, and thus dielectric particles are arranged toward the direction of electric field in the area between two plates. When the two plates are close to each other, two different forces (i.e. repulsive force and attractive force) will alternately act on particles due to the structure change of the particles. The repulsive force occurs when the structure of particles is stretched by compressive force; whereas the attractive force occurs when the aggregate structure is broken. The cycle of the repulsive and attractive forces is a primary size of particle or size of aggregate, which depends on the degree of agglomeration. The measured size of particles, which is varied depending on their degree of dispersion and coagulation, determined the characteristics of the silica particles. In this research work, the effect of size and concentration of particles in aqueous solution on the degree of dispersion and coagulation of the silica particles were investigated. Spherical silica particles were selected for this investigation due to their variety of size. This apparatus can be used to evaluate the degree of dispersion and coagulation of other nano-particles in various solvents in many process industries.

Jan 1, 2014

By Yong Liu, Peng Qian, Shu-Feng Ye, Shao-Jun Chu, Pei-Wei Han

"Chromite with a low mass ratio of Cr to Fe (Cr/Fe ratio) was treated by the carbochlorination method using solid chlorinating agent (MgCl2 and CaCl2) and carbon in the present paper. The results showed that iron could be selective removed mainly in the form of FeCl2. The removal of iron was indirectly, which consisted of the decomposition of solid chlorinating agent to release Cl2/HCl and the carbochlorination of FeO•Cr2O3 by Cl2/HCl and C. The Cr/Fe ratio increased as increasing temperature from 700 ? to 900 ? in air atmosphere, while the tendency was opposite in N2 atmosphere. The removal efficiency of iron by CaCl2 was better than that by MgCl2. At last, a new pelletizing process was proposed to treat fine chromite with a low Cr/Fe ratio based on carbochlorination method, which could produce the high quality roasted chromite pellets with higher Cr/Fe ratio and compressive strength. INTRODUCTION Chromite is mainly used for the production of ferrochromium. A high Cr/Fe ratio (>2) of chromite is usually required to meet the technical specification of ferrochromium.(Gasik, 2013) Attentions have been attracted to the economic and efficient methods for the recovery of chromium from lower-grade ores as the higher-grade ores become depleted. However, the Cr/Fe ratio is difficult to improve through the conventional beneficiation methods (such as gravity concentration, flotation) due to the spinel composition, although beneficiation methods could increase the metal content of chromite ores by removing gangues.(Nafziger, 1982) The main industrial mineral of chromite is (Fe,Mg)O•(Cr,Al,Fe)2O3, which belongs to spinel magnetite.(Liu, 2013) Iron should be selectively removed through the structural dissociation of spinel to increase Cr/Fe ratio.(Nafziger, 1982)"

Jan 1, 2018

By A. V. Bauman

"Important for thickening processes is the ability of slurries to form under certain conditions aggregation and sedimentation stable systems. Substantial part of difficult to sediment solid particles in such systems may be in colloidal state. The technique to study the sedimentation and aggregative stability of the slurry developed by the author with co-authors makes possible to define kinetics of changes in the aggregative stability of the system with solid phase varying concentration in it and produce data on sedimentation stability of the system in preliminary investigation of the thickening process. Research of aggregative and sedimentation stability of the slurry complement standard methods of laboratory studies to prevent errors in development of water-slime thickening balance and water circulation to design new and upgrade existing processing plants. Statistical analysis of process audits of more than one hundred upgraded and newly commissioned processing plants carried out in recent fifteen years showed that more than two-thirds of problems arising in commissioning the processing plants are associated with misdesign and errors in thickening and water circulation system. Among the main reasons of process design failures are: non-conformity of actual characteristics of the raw material to design characteristics, low quality of preliminary studies at the stage of sedimentation process simulation, design failures, wrongly selected equipment for the thickening and water circulations systems. As of today a number of problems associated with laboratory studies of sedimentation process, first of all, with interpretation of precipitation curves produced at the stage of laboratory refinement of the thickening process have been pinpointed. (Bauman A.V. Outstanding issues in design of thickening and water circulation diagrams in processing plants // Ore processing. 2016. ?3 P. 58-62) ?????? ?.?. ?????????? ??????? ?????????????? ???? ???????? ? ??????????? ?????????????? ??????. // ?????????? ???. 2016. ?3. ?. 58-62))"

Jan 1, 2018

By John Starkey

"The development of the SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.Previously, it was deemed prudent to select up to 50 t samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5 t sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50 t sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By S. Mohanta

The air dense medium fluidized bed separator which has been developed for the dry beneficiation of coal is recognized as a low cost and high efficiency process. The success of this separator for beneficiating any specific coal, alone or in combination with other processing methods, mostly depends on the characteristics of run-of-mine coal. Therefore, a thorough knowledge of the mineralogical composition and washability characteristics of representative coal sample is highly essential for correctly and effectively assess the suitability of this process. Available literature conforms that although the characteristics of Indian non-coking coals are well known, the correlations between the particle compositions with its density are entirely lacking. In the present study the washability, proximate, ultimate and elemental analysis was conducted for four typical Indian high-ash non-coking coals and their elemental compositions were well correlated with the specific gravity of coal. The results obtained in this study provide some essential information to the coal-processing engineer for efficiently operate and control the process. Furthermore, the beneficiation potential of air dense medium fluidized bed was experimentally evaluated and compared with the results obtained from an operating wet beneficiation plant. Based on this comparative study the air dense medium fluidized bed is established to be a possible alternative to the conventional wet beneficiation method for beneficiating Indian coals with Ep values in the range of 0.03 to 0.06

Sep 1, 2012

By R. Weyhe, B. Friedrich, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990's. In 1999 the output of cells exceeded 80,000 tons per year (1 billion cells per year). Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps.After shredding the steel shell, the various fractions of battery materials are carefully separated by mechanical processing. A hammer mill with one rotor with a perforated discharge grid of 20 mm opening, was found to be suitable for crushing the batteries to release the active mass of electrodes for metallurgical processing. The ground material is wet screened at a mesh size of 0.5 mm; thus a fine fraction is obtained with valuable components such as Ni, Co, and RE and an oversized fraction consisting of a mix of iron chips, electrodes grids, plastic chips, paper, and flocculent material of separators. The organic components are avoidable when there is a thermal step at the beginning of processing batteries.The separated fine fraction is smelted in an electric arc furnace. Any pyrometallurgical process relies on a suitable slag system. In this specific case, the process has to allow separation of nickel and cobalt as metal from the rare-earths almost quantitatively, collecting the rare-earths as well as impurities e.g. as oxides. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’."

Jan 1, 2003

By David Newton, Christian O’Keefe, Robert Maron, Jerin Russell, Paul Rothman, Dylan Cirulis

"The presence of unwanted coarse material in flotation feed streams negatively impacts both recovery and throughput of concentrator plants. The detection of this coarse material is a long-standing problem in mineral processing that has been poorly addressed by existing instrumentation systems. This problem has been overcome by the development of two new systems that detect in real-time the presence of coarse material in the overflow stream of individual hydrocyclones. They both use sensors mounted to the overflow pipe of the hydrocyclone and provide a robust and maintenance-free system measurement that enables corrective actions through operator intervention or automatic control strategies. One system is non-invasive and detects very coarse material 6mm or greater in size. The other system uses a wetted sensor and detects coarse material down to a lower size limit of approximately 100 um. Both systems have been commercially deployed. The systems will be described in detail. Validation data and typical plant data will be shown"

Jan 1, 2014

By T. C. Sun

Two wasted activated sludges (WAS), from an industrial wastewater treatment and a sewage treatment plant respectively, and 7 collectors are used to investigate the feasibility of air flotation thickening of WAS by adding the collectors used in mineral processing. The collectors experimented include straight chain fat acids with different chain length, sodium oleate, alkyl sodium sulphonate, sodium dedecylsulfonate, and dodecylamine. The results show that the thickening efficiency varied depending on different collectors. Of the collectors experimented, dodecanoic acid and dodecylamine are best collector for thickening both sludges.

Jan 1, 2014

By X. F. Cao

There was a large reserve of bauxite resources in China. And these resources were mainly the dias-pore-bauxite and contained plenty of aluminosilicate including kaolinite, illite and pyrophyllite. Reducing the contents of aluminosilicate would be significant to the using of Chinese bauxite resources. In this paper, from the single mineral flotation experiments, the surface properties and flotation beha-viours of aluminosilicate including kaolinite, illite and pyrophyllite, using dodecyl amine (DDA), N, N-dimethyl-dodecyl amine (DRN12) and N-dodecyl-1, 3-propane diamine (DN12) as collectors, had been investigated. The flotation results shown that the flotation behaviours of aluminosilicate had been influenced greatly by three amine collectors; and the effect was in the order of DN12>DRN12 >DDA. On the basis of FT-IR spectra and zeta potential measurements, the ionization of surface hydroxyl, as well as isomorphic exchange of surface ions, accounted for the mineral surface charges. And the mechanisms of interactions between the mineral surface and collectors mainly included two modes: electrostatic adsorption and hydrogen bonding; for the DDA and DRN>DDA. 12, the mechanism was mainly electrostatic adsorption; and for the DN12, the mechanisms of electrostatic adsorption and hydrogen bonding both existed. Results of quantum chemistry research shown that the collecting ability of amine collectors was greatly influenced by the electro-negativity of N in the amine molecules; and The |E(EHOMO| and ?E (HOMO-ELUMO) of N atom in DRN12 and DN12 were lower than that of DDA, and the positive charge of ?N group in DRN12 and DA12 were higher than that of DDA. All these calculation results could explain the collecting power of DN12>DRN12>DDA.

Jan 1, 2014

By V. A. Feofanov

Technogenic water of ore mining enterprises, nonferrous metals operations, the enterprises of electroplating and instrument making, containing copper in the form of those or other connections can serve as perspective sources on receiving the copper-bearing raw material. Extraction of copper from the given water also solves a problem of water treating from a toxic component that reduces environmental load at evacuation of water in an open basin. The method of case hardening allows extracting copper selectively with reception of a deposit with the content of copper up to 70%. Weakness of the method is its efficiency basically in acid reduction, and also its low degree of copper extraction. On the basis of case hardening the method of galvanic coagulation is devised. It is based on the work of a short-circuited galvanic cell of iron-coke at variable contact of coupled metals components among themselves, cleared by the oxygen of air. The following processes of galvanic coagulation are considered: ? Extraction of copper; ? Formation ferrites of copper; ? Copper sorption on just-aggregated oxide forms of iron. Establishing conditions for passing the given stages provides an opportunity of copper extraction from technogenic water at any value of ??, content of salt and concentration of copper with reception of a compact deposit from which it is possible to extract copper by the known ways of enrichment and metallurgy. Investigations on optimization and intensification of galvanic coagulation with the purpose of reception the maximum rich deposit on copper have shown that the average contents of copper in a solution of 100~200 mg/dm3 the contents of copper in a deposit is 6%~10% at extraction 85%~90%, depending on characteristics of treated technogenic water. Using methods of scanning microscopy it is determined structures, composition and mechanism of phase formation in investigated electro-chemical process. The second stage of galvanic coagulation increases a degree of copper extraction up to 98%~99% that allows returning the cleared waters in circulation for waste recycling or evacuation in an open basin. Nowadays the method of galvanic coagulation is the most acceptable for copper extraction from technogenic water both from the point of view of efficiency and instrument setting that allows applying the method in conditions of the working enterprises.

Jan 1, 2014

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

The optimal design of flotation circuits is a complex task as the mathematical model is nonconvex and includes binary variables, making it difficult to obtain the global optimum solution. Furthermore, there are epistemic uncertainties in the evaluation of the performance of flotation and grinding units. This epistemic uncertainty is generated because semi-empirical models are used with parameters that are a function of the circuit design. Therefore, it is not possible to adjust these models based on experimental data as the experimental conditions are not known at the design stage. This paper analyzed the effect of the uncertainties in flotation units, grinding units, and both units simultaneously. As a result, this paper demonstrated that, for a specific mineral, few structures exist that are optimal for a wide range of values in flotation stage recoveries and liberation fractions in the grinding units. A remarkable aspect of this work is that it introduces grinding, one of the operations that most influences energy consumption in mining and has not been studied in depth in the design of flotation circuits. To demonstrate that there are few optimal structures for a specific mineral when there is high uncertainty in the process units, an a priori approach or first principles was used. Two methods of proof were used: proof by construction and proof by exhaustion. Proof by construction is the construction of a concrete example with a property to demonstrate that something having that property exists. In this work, two examples were considered in the proof by construction. In proof by exhaustion, the conclusion was established by dividing it into a finite number of cases and proving each one separately. Here, 30,000 cases were included for each example. This knowledge can be useful in circuit design including grinding, e.g., after selecting the circuit (or the most promising circuits), and the equipment design parameters and operating conditions can be defined based on simulation and laboratory tests.

Jan 1, 2018

By Jun Qiu, Ping Chen, Xianjun Lu

Nitrogen of different forms from wastewater was adsorbed by the natural bentonite and modified bentonite. The effects of adsorption conditions on the nitrogen removal were investigated. The experiment results showed that natural bentonite could easily adsorb ammonia while poorly adsorb nitrate, the organic bentonite modified by octadecyl trimethyl ammonium could effectively adsorb nitrate with the removal ratio increased from no more than 5% to 89%. Two kinds of bentonite were added together to the simulated wastewater which contained ammonia nitrogen of 15mg/L and nitrate nitrogen of 10mg/L, the dosages were 1.0g respectively. Both ammonia and nitrate had significantly decreased on conditions that the oscillation time was 1.0h and room temperature 20?. The optimum pH value for ammonia removal was 7 while for nitrate removal was above 7. The adsorption isotherm fitting results indicated that the Freundlich adsorption isotherm was the better model to describe ammonia adsorbed on the natural bentonite and the saturated adsorption capacity was 10.25mg/L, while the Langmuir isotherm could better describe the adsorption of nitrate on the organic bentonite and the saturated adsorption capacity was 14.35mg/L. Fully considering the interaction between different ions and controlling the appropriate conditions, removing nitrogen from wastewater by adsorption of bentonite is an economic and effective method.

Jan 1, 2014

By Häkkinen Antti, Salmimies Riina, Matveinen Maria

"Tailings generated during the upgrading of ore present a major challenge for the mineral processing industry. On one hand, the processing of tailings requires added capital input. On the other hand, increased difficulties in obtaining permits for dams and landfilling and increased costs associated with storage and tailings management also result in increased costs. To promote sustainability and make tailings management economical, added value must be generated from the waste material. This might be possible through the recovery of the metal values in the waste. This work discusses the possibilities of recovering metals from multimetal tailings through leaching in a stirred tank. The characteristics of the tailings are crucial and the distribution of the metals within the different size fractions is used to identify the most attractive route for the hydrometallurgical step. Leaching of nickel and copper is further investigated using acids at different concentrations. The leaching of base metals is possible at acidic conditions. Increased temperature and concentration of the leaching agent promote the dissolution of the metals, as could be expected. With simultaneous dissolution of several metals the dissolution mechanisms are difficult to identify. Furthermore, as several metals, not all of them being target elements, are leached another challenge arises from the selective recovery of those metals from the liquid phase."

Jan 1, 2014

By S. A. Bogidaev, M. Yu. Tiunov

"The paper describes the results of the flotation tests with complex rare metal ores from deposits in the Trans-Baikal Territory. Correlations between the quality of produced wolframite, hubnerite and mica concentrates with or without the presence of various alkaline modifiers are determined. Commonly, rare metal ores contain minerals of comparable value to main elements recovered in processing plants using gravitational methods. The paper describes the results of flotation recovery of valuable minerals – main and associated – from gravity tailings of deposits in the Trans-Baikal Territory. It was found that gravity tailings from the first deposit contained fine-grained wolframite, mica (muscovite, lepidolite etc.), feldspar; hubnerite, scheelite, beryl, fluorite, rubidium-containing muscovite from the second deposit, correspondingly. This paper presents the results of the stage flotation tests with the production of tungsten (wolframite, hubnerite), fluorite and mica concentrates from gravity tailings. Figure 1 demonstrates the flowsheet of tungsten ore minerals and mica stage flotation from gravity tailings of the first deposit.Wolframite can be floated using oleic acid with the presence of soda ash, a complexing collector (IM-50), under slightly alkaline conditions in combination with a nonpolar collector [1, 2, 3, 4]. The study included wolframite flotation using the combination of two alkaline modifiers. Flotation of wolframite was performed after pulp desliming, using tall oil saponified with soda ash. The recovery of wolframite in the concentrate of rougher flotation reached 80-85%; the concentrate contained up to 1% of tungsten oxide that can be upgraded to a saleable product using gravitational methods. This procedure was tested during flotation of wolframite, tantalite-columbite and pyrochlore, and provided high performance regardless of a season, at pulp temperatures of 8-10°C, though fattyacid collectors are significantly inefficient at such low temperatures due to low solubility, dispersion and increased collector consumption, consequently. The introduction of two alkaline modifiers in pulp appears to improve these characteristics.The first stage of the tests was focused on increase of iron-bearing tungsten ore minerals recovery from gravity tailings and stabilization of the cold pulp flotation process."

Jan 1, 2018