Search Documents

By Dwight D. Trueblood

The Benthic Impact Experiment (BIE) is designed to address the effects of sediment redeposition prior to the commencement of commercial mining. The experiment is being conducted in collaboration with Russian scientists from the Yuzhmorgeologiya Association aboard the R/V YUZHMORGEOLOGIYA. Sediment resuspension and subsequent redeposition during manganese-nodule mining is predicted to be one of the primary impacts on benthic communities living on the abyssal seafloor. The redeposition thicknesses that will cause significant faunal mortality in the deep sea are unknown. Sediment redeposition could adversely affect abyssal benthic communities through entombment, or through starvation caused by food dilution and obstructed feeding. This spring NOAA conducted the main portion of the BIE experiment, blanketing the experimental area with varying thicknesses of sediment using the Deep Sea Sediment Resuspension System (DSSRS). The DSSRS was conceived by NOAA scientists, designed and built by Williamson and Associates, and is the critical piece of equipment used to generate the controlled sediment redeposition environment on the 4800-m deep abyssal plane. The DSSRS consists of an 1800-kg sled, 4.8 m long, 2.4 m wide, and 2.2 m high. The sled was towed and powered using an 8,000-m, 26-mm single conductor cable having a 3,000 VAC capacity. As the sled was towed across the bottom, mud was ingested through two rear-facing, 45-cm wide intakes using two 7.6-horsepower pumps, and discharged 10 to 20 m above the bottom through two 20-cm diameter riser hoses. Each pump was instrumented with optical backscatter sensors providing real-time information about the discharge concentration.

Jan 1, 1992

By S. W. Chang, James R. Hein, S-R. Lee, A. Zondervan, H. Choi

"Nine Fe-Mn nodules from the extensive nodule field in the east of Campbell Plateau of southwest Pacific Ocean beneath the Deep Western Boundary Current (DWBC) and Antarctic Circumpolar Current (ACC) were analyzed for the 10Be/9Be dating by AMS (Accelerator Mass Spectroscopy) at IGNS, New Zealand.Several types of nodule morphology were identified including distinctive discoidal forms with overgrowths resulting possibly from overcrowding and partial sediment burial. Five principal nodule facies were also recognized by location and occurrence (Fig. 1) (Wright et al., 2005). Fe-Mn nodules show various concentric internal growth textures, such as, cuspates, large parabolic cuspates, pseudo-columnar, columnar, globular, and laminated, which vary even in a nodule with hydrogenetic, early diagenetic, or mixed origin. Each texture shows micro-textural varieties and different mineralogy and/or chemistry. The genesis of each internal texture was indicated by the REE patterns, the mineralogy of Mnoxides, and the Mn/Fe ratios."

Jan 1, 2017

By Fernando JAS Barriga

The world-class Neves-Corvo deposits were intersected by drilling in 1977. They occur in the (Carboniferous) Iberian Pyrite Belt (IPB), Western Europe&apos;s largest stock of base metals (see Bamga, 1990, in Dallmeyer RD, & Martinez E, eds, Pre-Mesozoic Geology of Iberia, Springer-Verlag). Massive and stringer sulfides in the area sum up to about 200 Mt (109 kg), in five main orebodies (Neves, Corvo, Graca, Zambujal and Lombador). They include unique, extremely high grade copper and tin ores ( - 33 Mt Cu ores, -7.5% Cu, and -4 Mt Sn ores, -2.6% Sn, - 12.5% Cu). Also present are -50 Mt polimetallic ores (-6% Zn, 1.2% Pb, 64 ppm Ag). The remaining are relatively low grade pyritic massive and stringer sulfides (Cu < 2%. Sn < 1%, Zn equivalent < 4%). The geological setting is one of bymodal submarine volcanism, with predominant felsic, explosive volcanism and associated sedimentation (detrital and chemical), which took place on a shelf-facies, quartzite-phyllite basement (of Upper Devonian age). The plate tectonic setting has been the object of much debate. Current interpretations favour that the IPB volcanism took place in a tensional fore-arc region, associated with oblique subduction and collision (Silva et al., 1990, same volume as above). At Neves-Corvo there are many different ores, that may be grouped in four main types: fissural (at the base), breccia, massive (intermediate) and "ruban6 " (at the top). Fissural ores seem to correspond to stockworks in contrasting types of host rocks (gray to black shale, sericitic, chloritic and graphitic, and light gray volcanic rock). Massive ore may contain significant shaly gangue, at the base of individual orebodies, and silica-rich (cherty) varieties towards the top. The more sulfide-rich varieties predominate, and are usually well banded.

Jan 1, 1993

By Roger Amato

The 1982 United Nations Convention on the Low of the Sea includes provisions under Article 76 for extending a coastal State&apos;s jurisdiction beyond the 200-nautical-mile (nm) Exclusive Economic Zone (EEZ) and for establishing the seaward limits of sovereign rights over natural resources. Article 76 prescribes a set of methodologies for determining these outer limits based on physiography and sediment thickness. The methodologies were applied to each of the five continental* margin areas of the United States - Atlantic, Pacific, Gulf of Mexico, Alaska, and Pacific Islands-using existing digital hydrographic and geologic data. Figures 1 and 2 show the results of applying the methodologies to the Atlantic, Pacific, Alaskan, and Gulf of Mexico continental shelves. Figure 1 depicts the preliminary limits of each of the Article 76 determinations for the Atlantic and Gulf of Mexico continental shelves. The Atlantic limits were described by Carpenter, Thormahlen, and Amato (1995) at the 26th Underwater Mining Institute.1 The limits for the Alaskan continental shelves are shown in Figure 2. Additional areas beyond the 200 nm EEZ are highlighted. These include a small area north of the U.S. - Canada boundary, containing 7,000 km2, a large area north of Point barrow (395,000 km2), and a third area north of the Aleutian Islands (178,000 km2). The shelf between the first two areas appears to have sediments thick enough to qualify for the 1 percent method (Irish Formula); however, year-round ice cover has prevented acquisition of seismic or drill data. The entire northern Alaska shelf is prospective for petroleum The Gulf of Mexico (Figure 1) has two small areas beyond the EEZ known as "doughnut holes." One is south of Louisiana and includes part of the Sigsbee Escarpment, an area believed to have potential for oil and gas. Oil was found on Sigsbee Knoll in cores from Deep Sea Drilling Project&apos;s Leg 1 cruise in 1968. The Sigsbee areas contains about 6,000 km2. The second area is south of the Florida panhandle and contains about 12,000 km2.

Jan 1, 1996

By Cornel E. J. de Ronde

Volcanic arcs, including both island arc and intra-oceanic arc systems, combined extend for ~22,000 km around the Earth, with the majority (~20,000 km) occurring in the Pacific basin. These arcs are host to over 700 volcanoes of which ~200 are submarine and as such represent great potential for hosting massive sulfide deposits formed at seafloor hydrothermal vent sites. The Kermadec arc extends for ~1,200 km northeastwards from the North Island of New Zealand and forms the southern part of the ~2,500-km-long Tonga-Kermadec intra-oceanic arc system. At least 94 volcanoes are known to exist along this system with 74, or about 80%, being submarine. At least 33 volcanoes occur along the Kermadec part of the arc with all but one (Raoul Island) being submarine. The first sulphides recovered from the entire Tonga-Kermadec arc were in 1996 from the Brothers and Rumble II West volcanoes of the southern Kermadec arc. The 1998 R/V Sonne research cruise recovered a more comprehensive suite of mineralised samples from Brothers, and also found evidence for hydrothermal venting at Monowai, Vulkanolog, Rumble III and Clark volcanoes. The March 1999 NZAPLUME cruise systematically surveyed 260 km of the southern Kermadec arc and found that 7 of 13 volcanoes were hydrothermally active, with the vent fields either located within calderas (e.g., Brothers, Healy, Rumble II West) or atop volcanic cones (e.g., Clark, Tangaroa, Rumble V, Rumble III). The May 2002 NZAPLUME II cruise surveyed a further ~580 km of the mid-segment of the Kermadec arc, from Brothers to volcano &apos;L&apos;, a submarine volcanic edifice 35 km NW of Macauley Island. This cruise surveyed 13 major volcanoes and 8 smaller volcanic edifices and confirmed hydrothermal venting at the Vulkanolog site, and discovered new vent fields atop a volcanic cone within Macauley caldera, immediately offshore Macauley Island, and another at the summit of volcano &apos;L&apos;. A further new site was found atop a volcanic knoll immediately S of Healy caldera during time-series sampling of the vent sites found during the 1999 cruise. All the vent sites discovered along the Kermadec arc occur in water depths between 1650 and 150 m.

Jan 1, 2002

By S. Kim Juniper

Ocean observatory technologies permit uninterrupted, real-time observation of dynamic seafloor environments such as gas hydrate deposits and hydrothermal vent fields that are of both scientific and economic interest. Such observations enable new discoveries of linkages between physical, chemical and biological processes and could permit continuous monitoring of environmental variables during mining operations. Ocean Networks Canada operates the NEPTUNE and VENUS cabled observatories in the Northeast Pacific Ocean. The offshore NEPTUNE observatory supports instruments at two gas hydrate sites on the continental margin off Vancouver Island, and in the hydrothermal vent fields of the Endeavour segment of the Juan de Fuca Ridge. The primary focus of the gas hydrate field observations is to understand the dynamics of the growth and stability of outcropping and sub-seafloor hydrate deposits. Outcropping hydrates at 840 m depth in Barkley Canyon have been monitored for the past 3 years with a mobile instrument platform known as Wally, which is operated over the Internet by a research group in Germany. This tracked vehicle carries standard oceanographic sensors, acoustic current metres, cameras and methane sensors. Data indicate a relationship between degassing of hydrates and tidal currents. In 2012-2013 two high-resolution sonar towers were added to the hydrate field to provide precision tracking of Wally and to monitor volume changes in the outcropping hydrate mounds. A large subsurface hydrate deposit occurs at the Clayoquot Slope site, where bottom depth is 1260 metres. Monitoring instrumentation is currently being established at this location. Gas bubble release from this deposit is being monitored by a sector scanning sonar mounted on a

Sep 14, 2011

By Timothy F. McConachy

Magmatic-hydrothermal activity in the South-West Pacific and SE Asian island arcs during the Tertiary has created a premier copper-gold province with numerous, commercially attractive base and precious metal deposits. This activity continues to the present day, especially in submarine sectors of those arcs where modern technologies enable direct observation of ore-forming processes in action. Until recently, however, the volcanic island arcs of Indonesia escaped such attention. The Indonesia-Australia Survey for Submarine Hydrothermal Activity (IASSHA), involved three cruises with KR Baruna Jaya VIII, focused particularly on the Sangihe arc; Tomini Bay, Sulawesi, including the vicinity of isolated Colo volcano; and the Sunda Strait including the neighborhood of Krakatau volcano. IASSHA 2001 and 2003 cruises studied the arc and behind-arc sectors of the Sangihe volcanic island chain extending northwards from Quaternary volcanoes on the northeastern tip of Sulawesi, near Manado, to the Kawio Islands near the border with the Philippines (Fig. 1). This chain lies above a west-dipping Wadati-Benioff seismic zone whose subduction trench is obscured by accreted sediments and mélange, forming the Talaud-Mayu ridge. West of the main active chain and extending northwards from Manado there is a subparallel ridge (The Manado Line) surmounted by a number of high (>2000 m) seamounts of uncertain age.

Jan 1, 2005

By Steinar L. Ellefmo, Maxime Lesage

"There are many reasons invoked when discussing the relevance of deep-sea mining minerals. The shift towards more focus on renewable energy (“the green shift”) will not be possible without more materials coming from the mining industry. The increasing population, and thus increased number of consumers, will lead to an increase of the mineral demand. It has been established that recycling will not satisfy the need for more minerals by itself. Meanwhile, land mineral resources - such as copper – become every day more complex to extract. The question of the deep-sea minerals exploitation’s viability needs to be studied now. Within the framework of feasibility studies, various topics such as environment, technologies and operations management must be addressed. Recognising deep-sea mining as a hybrid activity - taking from the mining, maritime and the offshore oil and gas industries - it is deemed too complex for a global assessment. Each deep-sea mining environment is worth its separate study.Norway is recognised as a seafarer nation. Looking towards the sea and driven by the will to thrive on the Blue Economy, Norway decided to investigate the case for deep-sea minerals on its Extended Continental Shelf. The MarMine project is a materialisation of this endeavour. The Norwegian case will address its own particularities such as a respectable water depth, the arctic environment, the remoteness to shore support and an environmental aware population as well as subsequent policies."

Jan 1, 2017

In 1983, the GEMINO research project (Geothermal Metallogenesis Indian Ocean) was initiated in order to locate and evaluate sites of recent or fossil hydrothermal activity in the largely unexplored Indian Ocean. During GEMINO cruises 1 and 2 with R/V SONNE in 1983 and 1986, the Central Indian Ridge between 21°S and 24°S was the subject of detailed exploration, including SeaBeam and magnetic mapping, hydrocasts, sediment coring, TV-grab sampling, and camera/video tows. Although hydrothermal sulfide mineralization was not located, a hydrothermal component in the sediment composition, hydrothermally altered basalts, and maximum concentrations of 27.5 nmol/kg Mn and 45.6 nl/l CH4 were discovered (Plüger and Herzig 1986; Herzig and Plüger 1988a). Leg 1 of the GEMINO-3 cruise in 1987/88 identified a neovolcanic ridge in the rift valley of a 30 km segment at 22°55&apos;S as a site of weak hydrothermal activity and photographed smectite-like precipitates on basalt talus and a chimney structure on top of a ridge-parallel fault scarp. Water temperature data and the distribution of Mn and CH4 were interpreted as indicative of diffuse, low-temperature hydrothermal activity (Herzig and Plüger 1988b).

Jan 1, 1989

By William J. Scott

In the last two years, C-CORE has developed a new seabed sampler directed specifically at obtaining samples from hard or compacted bottoms such as are typical of marine placer deposits. Samples are required for appraisal of concentrations of saleable commodities, and for determination of levels of biological indicators in the deposits. Recently C-CORE and the University of Victoria have been comparing the performance of the Scott/C-CORE sampler with that of the Van Veen sampler often used for biological sampling. Initial trials of the Scott/C-CORE sampler in 1992 at the WestGold mining site, Nome, Alaska, were described by Jewitt et al. at the 1993 UMI. Since that time the sampler has been modified to prevent overfilling, and to limit turbulent flow of water across the top of the sampler buckets when the sampler is recovered with partly-open buckets. The modifications included shoes to prevent sampler overfill, and flexible rubber shielding over top and sides of the sampler to prevent water circulation. Samples have been taken with both samplers in two field areas, one at Pine Cove, Baie Verte, Newfoundland, and the other near Long Pond in Conception Bay on the Avalon Peninsula, Newfoundland. In each area multiple samples were taken with both sampler types, and the samples processed immediately to establish the types and quantities of marine organisms that were present. Species identification is expected to be complete by late August.

Jan 1, 1994

By William J. Scott

In the last two years, C-CORE has developed a new seabed sampler directed specifically at obtaining samples from hard or compacted bottoms such as are typical of marine placer deposits. Samples are required for appraisal of concentrations of saleable commodities, and for determination of levels of biological indicators in the deposits. Recently C-CORE and the University of Victoria have been comparing the performance of the Scott/C-CORE sampler with that of the Van Veen sampler often used for biological sampling. Initial trials of the Scott/C-CORE sampler in 1992 at the WestGold mining site, Nome, Alaska, were described by Jewitt et al. at the 1993 UMI. Since that time the sampler has been modified to prevent overfilling, and to limit turbulent flow of water across the top of the sampler buckets when the sampler is recovered with partly-open buckets. The modifications included shoes to prevent sampler overfill, and flexible rubber shielding over top and sides of the sampler to prevent water circulation. Samples have been taken with both samplers in two field areas, one at Pine Cove, Baie Verte, Newfoundland, and the other near Long Pond in Conception Bay on the Avalon Peninsula, Newfoundland. In each area multiple samples were taken with both sampler types, and the samples processed immediately to establish the types and quantities of marine organisms that were present. Species identification is expected to be complete by late August.

Jan 1, 1994

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Pavel Mikhailik

INTRODUCTION Ferromanganese (FeMn) crusts from Mendeleev Ridge, Chukchi Borderland, and Alpha Ridge, in the Amerasia Basin, Arctic Ocean, are similar based on morphology and chemical composition. The crusts are characterized by two- to four-layered stratigraphy. The chemical composition of the Arctic crusts differs significantly from hydrogenetic crusts from the North Pacific Prime Zone (PCZ; Hein et al., 2013), such as a high mean Fe/Mn ratio (2.6 versus 1.3) and low Si/Al ratio (1.8 versus 4.0), with lower Mn, Ca, Ti, P, Ba, Co, Cu, Ni, Pb, Sr, and Zn and higher Si, Al, Mg, As, Li, V, Sc, and Th. Based on Arctic FeMn crust mineralogy, chemical composition, and growth rates, crust formation was dominated by three processes: Precipitation of Fe-Mn (oxyhydr)oxides from ambient ocean water, sorption of metals by the Fe and Mn phases, and fluctuating but large inputs of terrigenous debris (Konstantinova et al., 2017; Hein et al., 2017). The Mn and Fe phases are hydrogenous and reflect bottom ocean-water chemistry and the aluminosilicate phase contains stable detrital minerals such as quartz, feldspars, zircon, monazite, and clay minerals. A precise method of studying the distribution of elements in FeMn crust phases is sequential leaching that dissolves four mineral phases of different stability step-by-step, in the following order: easily leachable phase, mostly bio-calcite; manganese oxides; iron oxyhydroxides; and residual aluminosilicate minerals (Koschinsky and Halbach, 1995). Twelve bulk crusts and crust layer samples obtained from six hydrogenous FeMn crusts were studied. Those crusts were collected during Russian (Arktika 2012) and USA (HLY0805, HLY0905, and HLY1202) research cruises from different parts of the Amerasia Basin (Mendeleev and Alpha Ridges, Chukchi Borderland). Samples were chosen for the sequential leaching experiments based on their morphology, location, and water depth. Hydrogenetic crust (D07-33) from the Tuvalu EEZ, central-west Pacific Ocean, was included in the experiment for comparison. Recovery during the four-step sequential leaching, with respect to the bulk analyses, was between 80% and 120%.

Jan 1, 2018

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By Art Wright, Steinar L. Ellefmo, Kurt Aasly, Mike Williamson, Fredrik Søreide, Martin Ludvigsen, Michael Zylstra

Exploring for minerals on the seabed is challenging and expensive – and the ability to collect representative sub surface samples is essential. The research project MarMine led by NTNU has together with Seattle based Williamson and Associates developed and tested an ROV-based drill rig for mineral (seafloor massive sulfides and crusts) and rock sampling. The ROCS system is a single stroke drill and is simple, robust and possible to use from various larger ROVs. For the vehicle to provide a stable platform, the vertical bollard pull of the ROV and the vehicle mass are important variables. The developed drill uses a thin wall drill bit and barrel and operates at high RPM to reduce the required down weight and drilling moments. The system also contains an emergency release to be used if the core barrel is stuck. The drill is hydraulically powered with cylinders operating the tower and a rotation unit. It can rapidly be modified to provide samples from softer samples like unconsolidated material. At the Arctic Mid Ocean Ridge, a work class ROV was deployed with the drill mounted for testing at 2700 m depth in basalt rock. The recovery from the system was above 80%. Such core samples can be used for chemical analyses of metal and mineral grades, mineralogy and rock mechanical testing. The system provides a probing tool for marine mineral exploration, with low cost, low operational complexity and low risk. Proper resource estimation requires drilling deeper into the deposit, but the short core samples provided by the ROCS provide valuable a priori information planning for more extensive drilling campaigns.

Jan 1, 2017

By Chan Min Yoo, Kiseong Hyeong, Inah Seo

INTRODUCTION One of the major concerns for deep seabed mining is its environmental impact, from the disturbance of benthic communities due to the mining activity to the disposal of mine tailings back to the ocean. Yet a significant amount of waste materials would be produced from the on-deck processing on the mining platform, all the materials that produced on the mining platform are to be shipped to the land unless the related regulation and guidelines are developed by IMO and ISA (ISA, 2018). Still, ecotoxicology data for the deep seabed minerals from case studies in deep-sea tailings disposal (DSTD) and submarine tailings disposal (STD) sites are lacking and all other related aspects are also largely unknown. This year, the Republic of Korea has started a research project for the more comprehensive understanding of chemical and physical properties of mine tailings from the on-deck processing and the possible environmental impacts on the marine organisms after its disposal. Based on the scientific data collected from this project, Korea would be able to make recommendations for the methods and technical standards for the deep seabed mining discharges. The subjects of this project are threefold: to understand the physical/chemical properties of the tailings, to model the dispersion of particulates after the disposal, and to assess its impact on the marine ecology. Laboratory Experiments Producing Mine Tailings First, the possible waste materials are produced by mimicking the collecting and dressing processes at sea. The polymetallic nodules (PN) would be mined by using a collector lifting the crushed nodules out of the bottom sediment, and the bottom water, accompanying sediment, and the fine nodule particles which are too small to be recovered would be discharged to the ocean and thus are considered as tailings (Schriever and Thiel, 2013). In the laboratory, PN is crushed into the fragments smaller than 2 cm, abraded in the water using the rock mill, and then sieved to obtain the fine particles to be disposed.

Jan 1, 2018

By Fernando J. A. S. Barriga

"Recent concerns over the availability of many mineral raw materials, and newly available technological developments, produced renewed interest in deep-sea mining. However, environmental concerns, with variable degrees of justification, are raising opposition to the concept. The forecast for the behavior of consumption versus availability of many raw materials, nearly all critical metals, arguably show that consumption will grow much faster than resource discovery onshore. Finding new sources of raw materials seems inescapable. The deep seafloor stands out as the only likely candidate.Sea Floor Mining and the EcosystemMarine mining has already started, decades ago, for diamonds, currently up to depths near 400m. Although the industry recognizes there is a footprint, it considers the footprint quite minor, because the area mined is small: in Namibia, where offshore diamond mining is now 70% of the country’s total, only 3% of the concession of 3,700 sq miles (9600km2) have been mined. As plans to mine deep-sea massive sulphide deposits and polymetallic nodules progress, the environmental concerns grow. Some of these concerns are as follows:?The deep-sea ecosystems are composed of long-lived species, with low rates of reproduction. The environment may not recover from mining on a human time scale;"

Jan 1, 2017

By Henk van Muijen

From an interesting and intriguing scientific research topic, deep sea mining has altered into an interesting mining prospect over the last years. Ten years ago most of the focus was on geological investigations, searching for typical deep sea deposits and getting answers on where we can find them and how these deposits were formed. At this moment we know much more about the interesting deposit possibilities and with our quest for minerals, metals and other materials to feed global economic growth, answers as to the technical and economic feasibility to mine these deposits are sought. This is not a new phenomenon as we already witnessed such question late 1970?s and early 1980?s. Most of the focus was on mining manganese nodules and brines in the Red Sea driven by the report of the Club of Rome that predicted shortages in near future at that time. Development went different, but later in the 1990?s a rival of interest could be noticed for mining deep sea deposits.

Jan 1, 2010

By S. Rajendran

Gas Hydrates (Methane Hydrates) are solid, ice ? like substances composed of water and natural gas. They occur naturally in areas of the world where methane and water can combine at appropriate conditions of temperature and pressure and are found in the ocean bottom sediments and in some permafrost areas. Besides temperature and pressure, factors like bathymetry, sediment thickness, sedimentation rates, and total organic carbon content (TOC) also control gas hydrate formation in the sea. The stability of gas hydrates depends on the critical high pressure ? low temperature combination (0-17 bars, 0-25ºC), which in turn dependent on the mix of gases from which the mineral is formed. As the critical parameters can be altered by deposition, erosion or slumping of sediments, formation or melting of ice cover, rise and fall of sea level and sudden temperature changes induced by tectonic activities, current flows or volcanisms, the gas hydrates tend to be very unstable. It is becoming increasingly evident that naturally occurring gas hydrates are significant component of the shallow geosphere and are of societal concern in at least three major ways: as an energy resource, a geologic hazard and a major contributor for climatic changes.

Jan 1, 2010

By T. Yamazaki, R. Arai, N. Nakatani, K. Kuroda

"These 40 years, deep-sea mining for manganese nodules, cobalt-rich manganese crusts, and seafloor massive sulfides has been continuously business and R&D targets. The economy is the most important factor for realizing the venture. Some technological options to increase the economy of deep-sea mining are introduced. They are a mechanical lift, waste rejections on seafloor, a substrate recovery as byproduct, and a pulp lift. An example application of one of the options is economically examined. Not only the same type examinations but also some technological clarifications of the options in detail are necessary.BACKGROUNDManganese nodules (nodule), seafloor massive sulfides (SMS), and cobalt-rich manganese crusts (crust) have been well recognized as future metal sources these 40 years. Among them, the nodule was the first recognized ones. The mining technologies for the deep-sea mineral resources, therefore, have been mainly developed in the major R&D projects for the nodule.The mining systems considered were shuttle miner, continuous line bucket (CLB), and hydraulic dredge ones. The shuttle miner system studied by France was a kind of basic study for autonomous underwater vehicle. The CLB system was an effective approach for a small scale and less investment cost mining (Masuda and Cruickshank, 1995). However, both were considered not effective for a bulk scale production rate mining such as 1.5 million tons per year in dry weight. In the hydraulic dredge system, a steel-pipe and flexible-hose conduit for nodule transportation named “pipestring” and a hydraulic pumpup instrument for creation of upward water flow in the pipestring named “pump-lift” or “air-lift” were adapted and developed. Hence, the hydraulic dredge system became the main stream in the mining system."

Jan 1, 2017

By Paulo Chaves, Márcia Gonçalves, João R. S. Carvalho, Fernando J. A. S. Barriga, Edgar Carrolo, Tiago Luna, Ricardo Rato, Anabela Bento

INTRODUCTION For the last decades, deep-sea marine resources such as seabed massive sulfides (SMS), polymetallic nodules and ferromanganese crusts (Fe-Mn crusts) have received an ever- increasing amount of attention worldwide for their abundance in critical metals and potential commercial value. This interest has mostly been driven by the growing world demand for raw materials, in particular for high- and green-technology applications (e.g., hybrid and electric cars, batteries, photovoltaic solar cells, cell phones, super magnets), as well as by industrialized countries governments other than BRICS states need to secure a more diversified supply of metals, resulting in a new deep ocean exploration boom. Since the oceans and its resources are increasingly seen as indispensable for humans needs and their challenges in the decades to come, this boom increments pressure on marine areas, either in international or within countries economic exclusive zone (EEZ). Since 2002, the International Seabed Authority (ISA) has signed up 29 contracts with several entities and national governments from multiple countries (e.g., Japan, China, Germany, France, Russia, India, Rep. of Korea, UK, Canada, Brazil) for exploration for deep-sea mineral resources in international waters, either for scientific or commercial proposes, which together cover over 1.3 million km2 [1]. In turn, over 300 exploration licenses, covering more than 650,000 km2, have been granted within the EEZ of Pacific countries such as Papua New Guinea, Tonga, Fiji, Solomon Islands and Vanuatu [2, 3]. This number is expected to increase very rapidly, as 77 countries have proposed to the United Nations the extension of their continental shelf in order to extend their EEZ and jurisdiction over potential deep-sea mineral resources [4]. Its estimated that 42% of the potential areas for SMS occurrences, 54% for cobalt-rich Fe-Mn crusts, and 19% for polymetallic nodules lie within the EEZ of coastal countries [5]. In addition, a huge amount of seafloor is yet to be explored and evaluated. Combined, the size of the granted exploration areas represents less than 10% of the overall area thought as most favorable for the occurrence of the 3 types of deep-sea mineral resources above mentioned. This means that today’s assessments on deep-sea mineral resources are only a rough approximation.

Jan 1, 2018