Search Documents

By John S. McCartney, Ismaail Ghaaowd

This study presents the results from centrifuge modeling experiments performed to understand the effects of temperature changes on the pullout capacity of scale-model energy piles embedded in normally- consolidated clay layers. The energy pile under investigation is an aluminum cylinder instrumented with internal strain gages and thermocouples, and its temperature is controlled using an internal electrical resistance heater. The energy pile was first heated until the temperature, pore water pressure, and volume change of the surrounding clay layer stabilized, after which the energy pile was cooled. Pullout tests were then performed on the energy piles heated to different temperatures to understand the effects of the preceding heating-cooling cycle on the pullout capacity. In addition, the clay undrained shear strength profiles were measured using push-pull T-bar penetration tests before and after heating. INTRODUCTION When a heat source such as an energy pile is embedded in a saturated clay layer, temperature changes will result in changes in pore water pressure as the rate of heating is typically faster than the rate of pore water drainage (Campanella & Mitchell 1968, Abuel-Naga et al. 2007, and Ghaaowd et al. 2016). Although all soils will initially expand during undrained heating, normally consolidated soils typically exhibit permanent contraction while overconsolidated soils exhibit expansion after sustained heating when drainage is allowed (Vega & McCartney 2015). Subsequent drained cooling typically leads to elastic contraction. Thermally- induced changes in pore water pressure and volume during transient heating and cooling may affect the soil- structure interaction of energy piles, as well as the ultimate capacity of the energy pile. This study is relevant as relatively few studies have been performed on the behavior of energy piles in soft clay (e.g., Ng et al. 2014), with most focused on the behavior of drilled shaft energy piles in stiff rock or overconsolidated clays (e.g., Laloui et al. 2006; Murphy et al. 2015; Wang et al. 2015; McCartney and Murphy 2017).

Jan 1, 2018

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

By Guilherme L. M. G. Carvalho, Zachary T. Fleming

In a world of 2-dimensional design documents, envisioning and understanding 3-dimensional interferences for complex foundation construction scenarios can be challenging. Videos and computer models serve as 3-dimensional spatial aids but have drawbacks related to a fixed perspective. Augmented and virtual reality (AR/VR) provide new tools to communicate design challenges and improve construction planning. This paper provides a practical look at the basics of AR/VR systems and the tools available to the foundation design and construction industry by giving a high-level example of the technologies’ use in the design and delivery phases of a complex micropile installation project for the remediation of a dam foundation. Using these technologies, GEI was able to design and deliver a complex foundation remediation solution. AR/VR benefited regulators, and the client, to help understand the design concept, construction sequencing, and approach to overcoming installation challenges. Due to its user-friendly nature and less rigorous programming and hardware requirements, AR proved to be more useful than VR for this scenario. AR/VR will likely not replace videos and computer models; however, it can be a useful 3-dimensional visualization aid that complements the project delivery process and offers benefits that traditional methods cannot. INTRODUCTION Augmented and virtual reality is a promising and rapidly developing technology within the engineering and construction world. Like any rapidly developing new technology, the language describing it can be confusing and dynamic. To eliminate the confusion some definitions must be made. AR/ VR definitions The definitions of virtual reality (VR) and augmented reality (AR) for the purposes of this paper are as follows: VR is a computer-generated immersive environment that the user experiences within a digital 3- dimensional space (Satava, 1993)AR is a composite view created by superimposing digital objects into the user’s real-world view (Azuma, 1997). Often, VR is used in an office environment and allows the user to “visit” the digital site to review site planning, construction sequences, and interference geometry. AR can be utilized in both the office and onsite environments. Like VR, the in-office application for AR is commonly site planning. AR also can be utilized in the field for applications such as seeing through the ground to locate known existing obstructions like utilities, gas tanks, etc.

Jan 1, 2019

By Masaki Kitazume

Deep mixing method, in-situ admixture stabilization technique, has been developed and adopted for on land and marine construction works in Japan. The geotechnical design procedure of the method has been standardized in Ministry of Land, Infrastructure and Transport Government of Japan for port and harbor facilities, which includes the block type and wall type improved grounds for foundation stability, settlement reduction purpose. This procedure is based on the allowable stress concept, in which the induced stresses within the improved ground are confirmed to be lower than the allowable strength in the internal stability calculation. This procedure has been cited by several organizations to establish their standards. The Ministry has a plan to introduce a reliability based design for marine construction works in 2006, in which the design procedure on DM improved ground will also be modified to the reliability based. In the new design procedure, the average and variation of soil parameters and external loads are incorporated by partial safety factors to investigate the stability of improved ground. According to the plan, the author has been studied the design procedure and the magnitude of partial safety factors, and has established a preliminary draft of the standard. This draft will be brushed up through comparing the current design procedure. In this article, the design concept and design procedure of the method are briefly described.

Jan 1, 2004

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By Federico Pagliacci, Marco Chiarabelli, Salvatore Miranda

The paper describes the adopted technologies and performance controls related to a special geotechnical engineering solution provided within the scope of the Galataport Project, in Istanbul, Turkey. The scheme is the one applied to the new quay of Salipazari, which is a combination of retaining structure and ground improvement, formed by a combi-wall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high profile Project. The results of the in-situ and laboratory tests carried out on the improved soil are also presented. Main discussed points are: • History of Galataport and main Project details. • Design principle and soil condition for the new quay of Salipazari. • Difficulties encountered during execution of DSM. • Preliminary field trial tests conducted to establish the operational parameters, with relevant in-situ and laboratory tests executed. • Preliminary tests on material used for DSM (seawater and CEM IV SR). • Electronic equipment mounted on the rig, which allows the automatic execution of DSM columns. • Final QA/QC tests conducted to verify the performance of DSM, mainly consisting in: coring with relevant laboratory tests on samples (UCS + Es), seismic refraction tomography and seismic cross hole tomography. Correlations between UCS and Es, and between Es and Edyn are also presented. • A cross section of the executed treatment could be inspected on site during excavation. Photos and considerations are also presented.

Jan 1, 2018

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

Case I- Timber Pile Test- 4 pages describe the pile driving record, the pile load test and the boring log. Case II- 24 inch square prestressed concrete pile-5 pages give details about the pile driving, the boring log, the pile driving record, and the pile load test. Case III- 12 inch square prestressed concrete pile- 5 pages describe the compilation of SPT blow counts for the whole project, the pile driving record, the pile load test and the detailed boring logs. The 70 foot long pile was driven by a Vulcan 08 pile hammer. Case IV- 12 BP 53 Steel H pile- 3 pages give the pile load test, the pile driving record and the nearest boring log. The 64 foot long pile has its tip at elevation 908 ft. and the ground is at elevation 972 ft. The contractor augered to elevation 959 ft. before driving the pile with a Conmaco 08 single acting pile hammer. The hammer had an 8000 pound ram, a rated energy of 26,000 ft-1b., and a 7 1/2 inch thick asbestos cushion. Dynamic measurements were made during driving of the test pile and measured a hammer energy equal to 12,500 foot-pounds.

Jan 1, 1988

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

By P. V. Chandramohan

"In ports, piled berths are designed and constructed for berthing of ships with a finite draught. Piles in a bridge foundation also have a large free stand above scoured level. The piles of these structures have to withstand large horizontal forces imparted by the impact of the approaching vessels or due to longitudinal and transverse action in a bridge. It is also imperative that these piles have to project out of the dredged / scoured bed. These piles are normally designed as slender compression members subjected to bending also. They are subjected to vertical load tests for assessing the soil resistance. Lateral load tests, as a rule, are also stipulated. IS and IRC codes stipulate a deflection criteria for lateral load test to arrive at the capacity. These tests are usually conducted on a working pile by jacking out two piles. At the time of the test, pile will be free headed. But in service, piles are fixed head. There is a large difference in deflections between a fixed head and a free headed pile. Besides, a free headed pile will be subjected to a much higher bending moment than the fixed head one. This will put the working test pile under risk of breaking during the test. The problem is analyzed with case studies. INTRODUCTION Vertical capacity of piles is assessed by static formulae. This formula is based on the soil properties obtained from random soil exploration and laboratory and in-situ testing. Since soil is not a homogeneous medium, properties can vary. The design parameters taken for computations may be different from the ones at the interface of the pile with the soil. The best way is to find out is by a load test. The code IRC:78-2014 has rightly stated that initial load test is part of the design process. This is true with the vertical load test. But there are certain problems with the purpose and inference of the lateral load test. In both the tests the criteria for acceptance is the quantum of movement of the point of application of the load. In the former, the movement is vertical and depends more on the compression of the soil than the compressive strain in concrete. But in the latter, this movement is partly on account of the flexural rigidity of the pile and partly due to the horizontal compressibility of the soil. The role of rigidity of the pile is more when compressibility of the soil is higher. Lateral load test is done by jacking one pile against another because it is difficult to get an independent horizontal reaction. Please see Fig.1 Photo."

Jan 1, 2015

By D. P. Nicholson

The current phase of office development at Canary Wharf in the London Docklands includes twelve multi-storey buildings varying from eighteen to forty stories in height. The area of Canary Wharf South comprises five multi-storey buildings with low level in fill podium and garden areas. Three of these multi-storey buildings have "pile-cap" designs where the entire building load is applied to the piles. The remaining two buildings have "piled-raft" designs where allowance is made in the design for part of the building load to be transferred to the raft formation. Using a piled-raft design approach has enabled savings to be made on the number of piles used below the raft. This paper describes the calibration analysis undertaken to validate the design method. The ground conditions at the Canary Wharf site are typically fill and recent gravel deposits over the overconsolidated clay and sand of the Lambeth Group. Below these strata is the Thanet Sand. The Lambeth Group provided the founding layer for the raft and contributed to the pile shaft resistance. The Thanet Sand stratum provided the bearing layer for the 1.5m diameter base grouted bored piles. The piled-raft design required an assessment of the building load transfer through the raft to the formation layer. This load transfer led to significant increases in effective stress in the soil below the raft and thence a corresponding increased the capacity of the piles. This interaction of the raft with the prepared formation contributed to between 27% and 45% increase in total vertical load carrying capacity of the piled-raft substructure compared with the pile-cap design method. The development of the piled-raft design was carried out in three main phases: ? Development of the approach and validation analyses. ? Design work on various schemes resulting in detailed design packages. ? Validation analyses using full 3D finite element analysis (presented herein). The validation of the piled-raft design approach was initially carried out against published case histories for piled-raft interaction. To improve on the validation work a full 3D finite element analysis of a simplified pile raft and superstructure (which contributes stiffness to the raft) was undertaken; the analysis included only a quarter of the structure due to assumed symmetry of the structure and vertical loading. This 3D validation analysis is presented herein. The analysis was carried out using the Oasys LS-DYNA finite element program. Prior to carrying out the analysis of the piled-raft an initial finite element analysis was carried out to back analyse a fully instrumented field pile test providing accurate modelling of a single pile performance. This back analysis allowed confidence in the soil parameters used in the 3D model; comparisons of shaft and base resistances between the pile test and the FE model calculations for the single pile are presented. The parameters provided in this work were then carried into the full 3D model of the piled-raft. The 3D model of the piled-raft structure included 18 piles (12 full piles and 6 half piles on an axis of symmetry of the model).

Jan 1, 2002

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Raymond J. Castelli

The paper provides a general overview of the numerous types of earth retaining systems currently available, and organizes these various systems by several classification methods. These classifications can be used as a guide in identifying the appropriate type wall or walls for any specific project application. As a further aid in sorting through the numerous wall alternatives for a specific design or construction project application, the paper suggests a systematic approach for wall selection, and presents helpful charts summarizing the general advantages and disadvantages, and typical limitations for the currently available wall systems.

Jan 1, 2003

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By Madan B. Karkee

The understanding and the development of sound theoretical basis concerning the pile foundations has been phenomenal during the past few decades, considering the thousands of years the piles have evidently been in use. The importance of the quality assurance and the need for verification of load bearing capacity is being further reinforced rather than undermined by these developments. This is evidenced by significant developments made in the pile load test technology in recent decades, making it possible to make judicious selection of a test method, or a package of test methods, suitable for a given situation. The selection depends on the objective of carrying out the test and the reliability desired. Presently, the possible selection ranges from dynamic to static methods. The extent of dynamic effect in a test can be reckoned based on a dimensionless parameter defined as the 'relative duration'. Examples of different load tests are given for illustration of the different methods currently in use.

Jan 1, 1997

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Tracy Brettmann, Will Bohlen

An innovative retaining wall design consisting of tangent drilled shafts with supplementary seal piles was used to limit continuing bank erosion along the Brazos River in Southeast Texas. The riverbank erosion had progressed to where it was threatening the stability of both the bridge abutment and corresponding approach embankment of the heavily travelled Highway 99 bridge at this location. A tangent pile design was selected because it was both much faster to install and more cost effective than a secant pile system. The design included both 5.5-ft and 10-ft diameter shafts with depths up to 130-ft and comprised both anchored and cantilevered sections. Supplementary seal shafts were also installed between the structural tangent drilled shafts to help plug any gaps between the tangent shafts. The plumbness and diameter of the shafts were tested using a sonic caliper to make sure the shafts were installed within the specified tolerance. The initial design had to be revised when a record flood from Hurricane Harvey impacted the site during construction. Introduction The Fort Bend Grand Parkway Toll Road Authority (Owner) needed to protect the north bridge abutment with a retaining wall system due to rapidly eroding conditions of the Brazos River banks within the 300- feet-right-of-way of the State Highway 99 Jodie Stavinoha Bridge. The extent of the local scour and erosion along the north bank of the Brazos River has caused concern for the structural integrity of the bridge. The magnitude of the erosion along the north bank at the location of the bridge has been measured at about 120 feet over three recent hydrologic flood events locally referred to as Memorial Day 2015, Memorial Day 2016, and Tax Day 2016. During construction, a new record flood level occurred due to Hurricane Harvey in August of 2017 that resulted in a portion of the retaining wall needing to be redesigned due to even more erosion occurring. The Brazos River is an actively eroding and meandering alluvial river plain that naturally meanders and migrates over time. The processes of bank erosion and meander migration were ongoing before the bridge was constructed and will continue in the future. These recurring major flood events, however, rapidly increased the rate of erosion in just a few years. Background. Due to the need to protect the bridge as soon as possible, the Owner selected a project team consisting of the designer, general contractor and specialty deep foundation contractor prior to final design to work together in developing a cost-effective design that could be implemented rapidly. The project team initially considered both a secant pile and tangent pile retaining wall system using drilled shafts. After reviewing various alternative designs, a tangent pile wall with seal piles was selected based on both cost effectiveness and speed of installation. The tangent pile with seal pile option was approximately 20 percent lower in cost and 50 percent faster to install.

Jan 1, 2018

By Michael J. Atwood

Many buildings in Boston are founded on untreated wood piles, which can deteriorate and lose their structural capacity if groundwater levels are lowered below the tops of the piles, exposing the wood to air in the unsaturated soils that surround the piles. The problem of wood pile deterioration due to lowered groundwater levels in Boston first became evident in 1929 following discovery of rotten piles beneath walls of the Boston Public Library building. Repairs to reconstruct the library building?s wood pile foundations were made in 1930 using pit underpinning methods. Today, more than 80 years later, the subsurface conditions beneath several of Boston?s historic neighborhood areas continue to be plagued with low groundwater levels - regrettably resulting in ongoing deterioration to the wood piles that support some of Boston?s oldest and most beautiful buildings. Pit underpinning is still recognized as the preferred approach to repair wood piles and restore uniform foundation support beneath the impacted buildings. This paper provides a brief historical review of the land filling in Boston through the early 1900s that led to the use of wood piles as building foundations. Also discussed is the impact that groundwater level can have on the long term performance of wood pile foundations and the pit underpinning procedures used to reconstruct decayed wood pile foundations in 1930 beneath the Boston Public Library, and today beneath some of Boston?s oldest buildings. Also included are discussions on engineering controls and permitting requirements that help ensure safety and protection to the workers and buildings during underpinning, and some procedures being used to supplement and improve the loading capacity of the reconstructed foundations and facilitate construction of new useable below-grade space.

Jan 1, 2011