Search Documents

By Rüdiger Wunsch

The new high speed Vienna - St.Pölten line and the Lainzer tunnel are to be connected to the existing Western railway line in Vienna. This involves building an underground cut and cover branching tunnel which will be connected to the Western railway line by ramps. A key structure is the Herzmansky Street tunnel, which has a length of some 820m. It is to be constructed as a cut and cover tunnel using the top down method. The walls of the tunnel are designed as a water resistant structure consisting of double walls, an outer wall of bored piles and an inner reinforced concrete wall. The bored pile wall will be used as a temporary retaining wall during the construction phase and will also be a structural part of the per­manent tunnel wall. The retaining walls of the open pit, which will have a depth of up to 14m and a width of 12m, were investigated as a non-contiguous bored pile wall and overlapped bored pile wall. Preventing ground water from penetrating into the pit is of paramount importance. The high ground wa­ter level is the determining factor for the dimensioning of the bored pile wall and results in the require­ment for a water resistant concrete structure. It has been necessary to adopt adequate measures, therefore, in order to reduce the hydrostatic water pressure during the construction phase, assuming economical pile dimensions.

Jan 1, 2000

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By Donald Bruce, Mark Harris, Wesley Schmutzler, James Sanders

"This paper evaluates the history, construction and most importantly the performance of two remedial seepage cutoff walls installed in two major dams in the United States. Beaver Dam, on the White River in northwest Arkansas, was completed in 1966 and seepage through the karstic limestone under the embankment was apparent almost immediately upon filling of the reservoir. Several attempts to stop the seepage by grouting were unsuccessful. In 1994 a cutoff wall consisting of secant piles drilled with 32"" diameter down-the-hole hammers to a maximum depth of 185'?was completed and the seepage was reduced to a negligible amount. It has been over 20 years since the completion of the cutoff wall, and all indications are that the cutoff wall is performing as expected. Walter F. George Lock and Dam on the Chattahoochee River near Fort Gaines, Georgia, was completed in 1963 and suffered the same problem as Beaver Dam due to the limestone on which the dam was founded. Cutoff walls were installed in both embankments (1980s) and solved the problem in these areas, but under-seepage at the concrete lock, dam and spillway structures increased to the point that remediation was essential. The cutoff wall had to be installed through 110'?of water and another 100'?into rock upstream of an active dam that continued to generate electricity during the construction of the cutoff wall. A secant pile wall, in combination with a diaphragm wall, was completed in front of these structures in 2004. It has been over 10 years since the completion this cutoff wall and, again, the cutoff wall is performing as expected. The paper describes the construction of these cutoffs, but focuses on the long-term performance in terms of controlling seepage and piezometric levels.BEAVER DAMBeaver Dam is located on the White River, 609 miles above its mouth, in Carroll County, Northwest Arkansas. The construction of the dam and Beaver Reservoir was authorized on September 1954 by the Congressional Flood Control Act for purposes of water supply, flood control and hydroelectric power generation. The dam site was selected in 1957: construction began in November 1960 and was completed in June 1966. (FIG. 1)"

Jan 1, 2017

By J. -L. Briaud

This presentation shows the results of laboratory and field tests to date for the NCHRP project entitled "Downdrag on Bitumen-coated Piles". This project required to test a variety of bitumens in the laboratory to determine their properties and then to establish a field testing program to verify the bitumens effectiveness. Figure 1 shows an organizational chart that gives an overview of the agencies involved in the project. The first part describes the laboratory testing program in which bitumen samples of various types were obtained from a variety of manufacturers. Initially, classification tests were performed to verify the manufacturers' specifications. Additional tests were then developed and performed to determine the bitumens behavior under the various conditions that they may be exposed to in the field. The test results were analyzed and their usefulness for design purposes were determined. The test results are presented in either graphical or tabular form. The second part describes the field testing program which was designed to test the effectiveness of various bitumens under a wide range of soil, temperature, and construction conditions. The first site was in Edmonton, Alberta, Canada, where a construction project was to take place in the winter of 1989-90. This was ideal for the cold temperature extreme that was needed. The soil conditions were conducive to downdrag problems: an embankment placed over soft clay underlain by dense sand resulting in end-bearing piles. The other site was in New Orleans, Louisiana. The part of the project involving this downdrag study was to be carried out in the summer of 1990. The hot summer temperatures and extremely soft soil conditions (resulting in friction piles) gave the other extreme needed for this study. Each site is discussed in

Jan 1, 1991

By S. T. Kok

This paper presents a case study in West Malaysia for passive piles failure in very soft marine clay in open excavation. In this particular case, the thickness of the very soft marine clay ranges from 5 m to 7 m (16 ft to 23 ft) from the ground surface. Preliminary site investigation reported SPT ?N? value of zero for the very soft marine clay. The design was based on a deep foundation utilizing driven piles to support the superstructure. During pile cap construction, the piles were subjected to uncontrolled open excavation, inducing bending moment in the piles, resulting in some cracked and broken piles. Analyses were carried out using an existing three-dimensional finite element code with a non-linear soil model to predict the response of these piles during excavation. Finally, the predictions of pile responses during excavation were compared satisfactorily with the observed results.

Jan 1, 2009

By Robert W. Bergwall

The $58,000,000.00 Columbia Heights Metro Station project (Section E3-a) forms a part of the Washington Metropolitan Area Transit Authority's (WMATA) Greenbelt Route - Green Line subway system. The Greenbelt route is one often segments that make up WMATA's subway system. Construction of the "cut and cover" reinforced concrete station includes 600 linear feet of an underground center platform, two ancillary service areas totaling 466 linear feet, two surface entrances, and vent shafts (See Figure No. 1). Station subgrade is approximately 60 feet below existing grade. The project can be divided into five main areas: 1. North Service Rooms and Passageway; 2. West Entrance and West Passageway; 3. East Entrance; 4. Center Platform; 5. South Service Rooms. Station dimensions are approximately 1068 feet long by 64 feet wide. Construction commenced at the site in January of 1995 and is expected to be completed by December of 1999. Franki Northwest Company, Crofton, Maryland, was awarded a subcontract by general contractor Blake Construction Company, Washington, D.C, to install the support of excavation and temporary decking systems. Franki's scope of work included the installation of 490 drilled soldier piles plus two elevator shafts totaling 29,700 linear feet of drilling; 1,150 tons of steel decking covered by 37,000. square feet of precast concrete deck planks; 120,000. square feet of timber lagging; 2,500. tons of struts and wales; and temporary support of underground utilities. In conjunction with Franki's work, Bencor Corporation of America, Dallas, Texas, constructed parallel, 600 foot long slurry walls which serve as permanent walls for the center platform portion of the station.

Jan 1, 1997

By Dan A. Brown

This paper describes a method of conducting rapid lateral loading tests of deep foundations in which the load is applied to the foundation with a time duration of less than one second. For purposes of this paper the loading is applied using a pyrotechnic loading system commonly referred to as Statnamic. However, the method should apply to any lateral loading system which produces a force time history with a loading duration of 20 msec to 1 second. The test provides a measure of the dynamic and static response of the soil/foundation system and must be evaluated as a dynamic loading. Interpretation of the test includes a simple single degree of freedom (SDOF) model which can account for the inertial effects of foundation mass, system damping, and static foundation stiffness. The results of the test measurements are compared with four case histories in which comparative static load test data are available, including pile group foundations and large diameter drilled shaft foundations.

Jan 1, 2007

By Walter E. Vanderpool

Full scale load tests are frequently performed immediately prior to deep foundation construction to verify the design assumptions. Occasionally, load tests are performed during design development and applied to the final design for critical and non-redundant structures. We believe that full scale load tests can be very valuable and economical for projects, especially in a geologic environment where the record of full scale load testing is very limited or non-existent. The load testing for the Utah Transit Authority?s Airport Light Rail Trax project provides an example of the advantages of a load test in design development. The savings realized by the owner was in excess of $800 thousand dollars.

Jan 1, 2011

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By P. M. Wiltcher

The construction of a deep structural slurry wall in a restricted city centre location is always a challenging prospect. However, when the city is London and the site is bounded on two sides by high level canals and a main traffic highway on the third, the challenges are greater than usual. The paper discusses the design considerations required by the principal contractor to accommodate a single high level lateral support, value-engineered, bottom-up construction technique and the impact this had on the design detailing and construction of the slurry wall panels. This paper discusses the logistical challenges successfully overcome during the construction of 65,000sq ft of 40inch thick, 80ft deep structural slurry wall in the City of London. The paper reviews the benefits gained from using the state-of-the-art hydraulic grab and rotator system. Technological advances in computer instrumentation and real time monitoring were utilised to assist the grab operators in consistently delivering deviational control during excavation better than 1:200. With working space always at a premium on construction sites, the need for high quality, pre-fabricated reinforcement cages has never been greater. This paper reviews the argument for off-site fabrication of reinforcement members.

Jan 1, 2006

By Sudhir Kumar Das

"The exorbitant price of the land in the metropolis has restricted the horizontal expansion and compelled the owners, the developers and the engineers to opt for vertical expansion. This has resulted in the construction of high rises by extending floors of the existing buildings and developing the new ones for which deep excavation is a must. The multistoried buildings up to a certain height can be founded on shallow depth if the soil beneath can withstand the load. If not, the soil can be stabilized by the latest improvement technology to change the properties of soil to cater the desired load of the superstructures. By such practice the cost and time of completion of the substructures can be reduced in comparison to the substructures needed for deep excavation.The necessity of deep excavation cannot be ignored to create housings, underground parking lots and the other public amenities for the urban migrants in the metropolis.Although most of the metropolis have underground mapping the developers, before starting excavation should be hundred percent sure about the alignment and depth of the utilities so that the excavators do not snap the same to bring cut in water supply, power lines, telephone lines etc, resulting in hue and cry in the neighborhoods of the metropolis due to no availability of the essential services The building/structures coming on the influence zones of the deep excavation should be monitored in all sequences of excavations. In case of building underground corridors for rail or road through open deep excavation under a traffic road the developers, before commencing excavation should shift/divert the dry and wet utilities coming on the way of excavation to suitable locations. The surface traffic need to be diverted either temporarily to an adjacent alternative road or allowed to pass over a decking built over the trench of excavation for the affected length of construction. The soil support system is necessary longitudinally on the two sides covering the width of trench for building corridors. In case of building substructures of flyovers built at different plots along the alignment of the flyover or a multistoried complex built at an isolated plot, the soil support system would be necessary on all the sides covering the plot of construction.The material of construction of soil support depends on the depth, type of soil and the type of permanent structure to be developed. Probable geo-hazards inviting casualties in the deep excavation projects occur due to caving of soil, leakage of wet utilities, seepage through honey comb concrete surfaces, failure of pump used for dewatering etc. A detailed comprehensive planning, management and determination of the project authority is essential for marginalizing the casualties. These prevent unforeseen expenditure in mitigation and help to control the time and the cost over run of overall project. The engineer at site should be more a professional manager than an engineer at site. He should be conversant with the safety and environment rules and regulations applicable to deep underground projects."

Jan 1, 2015

By Peter Chou

A total of 117 slope stabilization drilled piers were installed as part of a major hillside revitalization project. The 110-million dollar development, known as Stratford at Kenwood, included an 18-story upscale senior residential tower, a 3-story healthcare building, and 4-story condominium buildings, offering approximately 580,000 square feet of living space with panoramic views of Downtown Cincinnati, Ohio. In an effort to establish a flatter hillside plateau for the new 4-story condominium and to create a cut and fill balanced jobsite environment, an 800-foot long row of drilled piers and a 600-foot long multi-tiered shear key system was used to terrace existing 1.5H to 3H: 1V steep slopes and support the new fill. These slope stabilization features reduced the amount of spoils needed to be wasted off-site and mitigated the risk of slope instability. An ODOT/FHWA research indicated that spacing of stabilization piers and necessity of top-connecting elements are highly dependent on pier diameter, spacing, soil type, depth to potential failure surface, surcharge loads, and pier deflection. Due to pre-existing deep buried swales, various load combinations, and the complex mechanism of soil arching effects between adjacent piers, both analytical and numerical computer modeling was performed to estimate the loading on each pier. New generation multiplexed, 3-Dimensional, Micro-Electro-Mechanical-System based inclinometers were installed between selected piers to confirm the pier design, and monitor the fill placement, as well as long-term slope stability.

Jan 1, 2009

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

By James L. Vinson

Wilbur Smith Associates (WSA) has provided planning, engineering and construction oversight assistance to the Tennessee Department of Transportation (TDOT) for three construction projects intended to widen and improve segments of I-40 and associated interchanges in Knoxville, Tennessee. The projects are within the karst terrain of the Valley and Ridge Province. Subsurface conditions are characterized by an irregular rock surface coupled with differential weathering. Because of the projects? impact to local and interstate motorists, consideration was given to innovative planning, materials and construction practices that could accelerate construction. Two innovative deep foundation measures included rock-socketed pipe piles, which act as both foundations and substructure elements for a bridge?s interior bents, and the first widespread use of rock-socketed drilled shafts as bridge foundations on a TDOT project. The pipe piles were used at a site with significant cavities within the limestone bedrock. This resulted in design verification and constructability difficulties that required delays, but measures were ultimately employed to produce a sound foundation system. Over 110 drilled shafts have been constructed at sites with generally low solution activity. Relative to H-pile footings, which were included as an alternate foundation, they have apparently allowed accelerated construction at a competitive cost.

Jan 1, 2006

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By Tom Szynakiewicz

Micropiles are routinely used in the United States for foundation support and underpinning applications. The high capacities achievable with the use of micropiles, combined with specialty rigs for easy installation in low headroom and difficult access areas makes them a good choice for situations often encountered on existing commercial projects. The bond zone of the pile is typically drilled into a competent stratum such as sands, gravels or bedrock. In this paper, the authors will discuss a project where the lack of a shallow ?competent stratum? led the geotechnical contractor to create their own bond zone for the micropiles using jet grouting. Due to problematic clay (CH) soils, the original foundation of a six story office building in west Houston had experienced up to five inches of differential movement in-between the shallow under-reamed shafts. The owner desired a permanent solution to the problem without disturbing the majority of the tenants. The structure was underpinned with a hybrid system of jet grouted micropiles as well as jet grouting alone and the structure was re-leveled using hydraulic equipment to within a 0.25? tolerance. Design, construction and sequencing of the project are discussed in the paper. QA/QC methods are also discussed, including coring for verification of jet grout column diameter as well as a full-scale micropile compressive load test. The structure was successfully re-leveled and the entire project was completed without disturbing any tenants on the floors two through six.

Jan 1, 2008

By Nuno Cruz, Saúl Rodríguez

"When executing offshore bored piles there are several specific factors and problems to consider in order to guarantee excavation stability. One of the methods employed to carry out this type of work consists in setting up a floating work platform, typically a barge, and implementing a soil stabilization system that combines a partial steel guiding casing with third generation polymeric drilling fluids. The main aspects to take into consideration when performing offshore pile boring works are soil stabilization, project design, work methodology and operational aspects. An example of a work methodology problem arises before any pile boring work takes place as the steel guiding casing contains water, sometimes salt water. What to do with this water in order to replace it by an adequate polymer fluid will determine the stabilization capacity as soon as the shaft advances below the protection of the casing. Another example of operational problem may derive from barge movements while executing boring activities. This study is the result of extensive field data collection and concrete logging analysis from marine projects using polymers in different continents. The bored pile stability target was set ranging between 2% to 15% of concrete overbreak. Values above 15% or below 2% mean that there is a stability problem. Then the off-target pile’s data is collected, analyzed and classified under categories. Thus, a direct correlation is established between the problem category and the final results. Modifying steps in the pre-established construction methods or operational variables guarantees target results without the need to replace the approved construction methods. As a general conclusion, the worldwide experience in large diameter marine works, allows to provide truthful information and solutions for these problems. In knowing how to follow a logical sequence of work and applying adequate work methodology will be the key for success.GENERALBackgroundTo carry out the drilling process of offshore bored piles there are two main options to take into consideration: drilling the pile by using full guiding casing until final depth; or using a combined system of partial steel guiding casing and support drilling fluids.The knowledge and situations described in this paper come from the experience acquired in different projects where the second method was employed. This construction method consists in installing a steel guiding casing by vibration and thus covering the water table and further stabilizing the soil below it with polymeric fluids until reaching the pile’s final depth. The Fig. 1 schematic shows an example of this method where H corresponds to the length of the steel guiding casing whereas the remainder of the shaft’s length is stabilized by polymer fluid. The entire bored length is full of slurry up to top of casing.In most cases this kind of civil works results from the need to build a bridge or executing port structures in places where the creation of temporary artificial peninsulas with fill material is impracticable or not allowed. Hence the need to use floating work platforms, commonly referred to as barges."

Jan 1, 2017

By P. Arz

With a total of five basement levels, ground floor and a further six levels above grade, construction of the Kö-Galerie building, on the Königsallee, in the centre of Düsseldorf, was completed with all the difficulties which accompany property development today in the inner city. To meet the intermediate and final deadlines, ad­vanced building techniques were used. Notable among them are the top/down method for simultaneous construction upwards and downwards from an intermediate level, and the use of pre-fabricated composite columns in drilled shafts for the main load-bearing foundations as well as diaphragm walls designed as permanent structural wall of the basement.

Jan 1, 1989

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987