Search Documents

By Ali Bouafia

Five full-scale horizontal loading tests of piles carried out by the LCPC in France are interpreted in order to analyse P-Y load-transfer curves. The experimental piles are either bored or jacked into quite homogenous sandy soils and instrumented by strain gauges for measuring bending moments along the pile. Successive differentiation and integration of bending moment profiles have led to derive respectively lateral soil reaction and displacements then to construct the load-transfer P-Y curves. The initial horizontal lateral reaction modulus was derived from these curves and shows linear variation with depth in accordance with Gibson soils profiles. P-Y curves are validated by back-computation of the pile on the basis de these curves and the horizontal reaction modulus was compared to the recommendations frequently used in pile design practice.

Jan 1, 2002

By Subhash B. Bhide

Deep foundations are affected by the presence of sulphates, chlorides, organic contents and water currents present in the soil. The sulphates in soil and ground water interfere first with setting of concrete. In long term, growing of sulphate crystals in concrete, crevices can spall the concrete. The chlorides mainly affect the steel. The organic content does not allow the concrete to set. It also reduces the compressive strength of concrete. The frequency and methods of sampling and testing for above corrosive elements are discussed. Presently available methods to avoid attack due to these corrosive elements are discussed. The stipulations by various codes are summarised. A method to assess the short term impact is elaborated with results of field studies. A tool developed to study the presence and effects of underground water currents on concrete is also discussed.

Jan 1, 1996

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By Nathan Iverson, Allie Brady

Located on rolling bluffs on the Zumbro River's south fork in Southeast Minnesota, Rochester is the state's third largest city and is the home and birthplace of the renowned Mayo Clinic, a nonprofit academic medical center focused on integrated health care, education and research. Mayo Clinic employs more than 4,500 physicians and scientists with another 58,000 administrative and allied health staff across three major campuses: Rochester, Minnesota; Jacksonville, Florida; and Phoenix/Scottsdale, Arizona. Originally developed as a stagecoach stop, Rochester has become a national destination for medical care, drawing more than two million visitors annually to Mayo's Minnesota location. Since January 2022, Veit & Company has been working on the construction of the Mayo 1st Ave Tunnel, which comprises three tunnels (pedestrian, utility and services), and the RMC Loading Dock projects in Rochester. These adjacent projects are on the Mayo Clinic's ever-expanding campus and represent its continued dedication to improvement and advancement as a leading medical service provider in the industry.

Jan 1, 2023

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By Anne Lemnitzer

When a major storm system stalled over Western Europe last summer, it pro- duced the deadliest flood on European territory in the last two decades. Beyond record-setting rainfall over countries such as Luxembourg, Switzerland, France and the Netherlands from the storm's "Bernd" low pressure system, more than 230 people were killed in Germany and Belgium. The storm system also caused over an estimated $20 billion (€17.7 billion) of damage. A team from the Geotechnical Extreme Events Reconnaissance (GEER) Association, supported by the National Science Foundation, was mobilized to investigate the potential impacts of the widespread flooding in Germany, Belgium and the Netherlands. Members of the DFI Europe regional chapter closely collaborated with the U.S.-based GEER team and many other engineers and scientists in Europe to collect perishable data and study flooding effects and the event's resulting impacts on geostructures, such as bridges, retaining walls, dikes and embankments. This article features some of the vast information collected by the team, which has recently been published in a comprehensive reconnaissance report and made available for free at geerassociation.org. All data will also be accessible at the NEHRI DesignSafe Cl data repository.

Feb 1, 2022

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By Makarand G. Khare

Though the phenomenon of dragload is known for many decades, there is a lack of clear guidelines to evaluate the amount of dragload. The development of dragload depends on relative movement between pile and surrounding soil which is a complex phenomenon and requires a detailed numerical analysis. Bitumen layer has been used in the past with varying degree of success in reducing the dragload but the reduction appears to depend on number of parameters. No procedure is available in literature to estimate the dragload when a slip layer is applied on pile surface. This paper investigates performance of two commercially available bituminous coats to reduce the negative skin friction on pile. Direct shear test apparatus was used to model the interface friction between soil and coated pile surface. The lower half of direct shear box was replaced with either a concrete block or a mild steel block representing pile surface. Two types of bituminous coats namely Shalikote and bitumen having penetration value of 30-40 were evaluated in this study. Shearing resistance of pile material-coat-soil is found to be influenced by normal stress, coat thickness, and rate of shear. Laboratory results are compared with published field data where coated and uncoated piles have been load tested.

Jan 1, 2006

By Kashyap Chaturvedula, Emad Farouz

The paper presents a discussion on the axial capacity of deep foundation elements bearing in the Yorktown formation in the southeastern region of Virginia. The fossiliferous marine soils of Tertiary age Yorktown formation typically consist of silty/clayey Sand or sandy Silt/Clay with varying amounts of shell fragments. The Yorktown formation is generally divided into Upper and Lower Yorktown layers depending on the shell content and the percent fines. Results of multiple load tests performed by Jacobs Engineering on auger cast piles as part of water and wastewater treatment plant expansion projects in southeastern region of Virginia are presented in this paper. The paper describes the subsurface investigation methods used to study the existing subsurface conditions and the design methodologies followed to estimate the axial capacity of the auger cast piles. The paper provides details regarding installation of test piles, instrumentation, load testing procedure, and interpretation of test results. The paper presents a comparison between the various methods of estimating axial capacity of auger cast piles based on the SPT-N values, the empirical methods for the Yorktown formation and the load test information. The paper distinguishes the side resistance values obtained within the upper and lower Yorktown formations. The paper compares the various design methods to the multiple load test results and recommends a design modification that is closer to the load test results.

By Alan G. MacKinnon

The current piling practices in the U. S. have, to a great degree, been influenced by our founding fathers. When our constitution was written by the delegates from the original thirteen colonies, it was a document of compromise. Generally, the individual states retained their sovereign power over those duties that they had historically performed. The concept of States Rights has been tested throughout our history and has been preserved as of today. An example of the extent of this protection is occurring in the State of Ohio where I currently live. Each of the 50 states receives funds for highway construction from the federal government, approximately in proportion to its population. Congress, when it allocates the funds, quite often attaches amendments to the funding bill to exercise their authority. The major amendment prior to the most recent increase in the speed limit to 65 mph from 55 mph was to increase the legal drinking age to 21 from 18 years old. Embodied within the bill was the provision that the Federal government deduct a percentage from the allocation of any state that did not revise its legal drinking age law from 18 to 21. In the State of Ohio, this change in the law was put to a vote of the people and it was defeated. The federal government now is deducting funds

Jan 1, 1987

By Masaki Kitazume

Five papers were presented orally to the topics of Jet Grouting and Deep Mixing. The session was started with a brief introduction by the moderators. Following the oral presentation, floor discussions were directed by the moderators. A brief introduction of each of the oral presentations is provided before each discussion.

Feb 10, 2003

By Jesus Gomez, Mary Nodine

Rigid inclusions are widely used in the U.S. as a ground improvement tech- nique, particularly for industrial, low- rise and highway applications with poor subsurface conditions, where control of settlement is necessary. Rigid inclu- sions consist of grouted or concrete elements typically 12-24 in (305-610 mm) in diameter that may or may not be reinforced with a center bar. Typical soil conditions where rigid inclusions are feasible might consist of a surface layer of fill and natural, granular soil, followed by a stratum of soft silt or clay overlying a dense or stiff formation. Rigid inclusions are installed from the existing ground surface or suitable work platform, through the surface soils and through the soft, compressible layer, and into the deeper layer, which is less susceptible to compression- induced settlement. Typically, when used to support an extended area surcharge, the inclusions are installed in a rectangular or triangular pattern at regular spacings ranging from 5-12 ft (1.54 m), depending on a variety of factors. The rigid inclusion system is often capped with a load transfer platform (LTP), whose function is to direct a significant portion of the applied load toward the rigid inclu- sions. Additional load is transferred to the rigid inclusions through the upper fill soils above the compressible layer. The rigid inclusions transfer the applied load axially to their tips and into the deeper layer. In the U.S., rigid inclusions are mostly installed using displacement auger systems. The use of a dis- placement auger has significant advantages. It produces zero to near- zero spoils, which is an important environmental consideration. The

May 1, 2023

By Mitsuhiro Shibazki

I can't answer that question but I am looking at Andy, my co-author, and he says we didn't measure it. No movement. If I understand it correctly, how do we handle lateral forces in shear? The main columns were designed as pin connections so there wasn't a moment in the shear between the pile cap and the columns the steel reinforcing was used to resist that. I am not aware of how we would have installed those, it is possible to try and submerge them all if the jet grout is still fluid. They were higher than design. You are correct.

Feb 10, 2003