Search Documents

By S. Malkin, Z. Shi, H. Attia, D. Chellan

An experimental investigation is reported on creep-feed grinding of a nickelbased alloy (IN718) using conventional aluminum oxide grinding wheels. Straight surface grinding expe.riments were conducted on nickel-based alloy blocks over a wide range of grinding conditions with straight oil as- grinding fluid applied at high pressure. Grinding power, forces, workpiece surface roughness, and radial wheel wear were measured. Specific material removal rate as high as 64 mm2/s was Used without burning the workpiece, which can be attributed to the extremely low specific energy of 12.6 J/mm3. It was found that the grinding wheel under the present test conditions had a strong capability of self-sharpening as indicated by the stabilized power, forces, and surface roughness after an initial short transient.

Jan 1, 2006

By W. P. Corking

"The purpose of this paper is to describe the relationship of the goldbearing ore to structure at the Pickle Crow mfoe. Information beyond this scope may be found in the reports and papers of Hurst( l), Bothwell(2), Thomson(3) , and Monette( 4).The property lies on Crow river, in Patricia district, 80 miles northeast of Allanwater, and about 125 miles northeast of Sioux Lookout on the Canadian National railway. From April of 1935, when the mill began operation, to the end of 1944, a total of 564,890 oz. gold and 49,275 oz. silver were recovered from 958,416 tons of ore.Mining on the property is at present carried on in two separate orebodies, the Howell and the No. 2 vein. Stoping has been carried on from every level on the Howell vein to a depth ot 2,450 feet below the surface and from several levels on the No. 2 vein through a mile long cross-cut on the 750-foot level to the Howell vein workings. A steadily increasing volume of ore is being obtained from the No. 2 vein.Each of the two orebodies consists of vein quartz with small amounts of other gangue minerals either in a single vein or a stockwork of veins. Both lie within sheared walls and carry gold in the free state. Fig. 1 shows the position of the veins with respect to the surrounding rocks. It will be noted that the delineation of the beds of iron formation shows that the lava flows and minor, interbedded sediments that make up most of the country rocks are areally folded and contorted.STRUCTURENearly all gold found to date in sufficient quantity and concentration to make ore in the Pickle Crow area is confined to these major quartz veins . Both strike a little north of east and dip north, and in both cases the attitude of the enclosing rocks is somewhat more north of east in strike and more steeply north in dip than that of the veins. As a result of this disposition both veins migrate across their enclosing rocks at a moderate angle in both dip and strike. (In this connection it should be noted that No. 2 vein dips at a considerably flatter angle than its host rock, but has a very pronounced rake to the northeast, effecting the same result as in the Howell vein.)"

Jan 1, 1954

By John S. Stevenson

The Twin ''J' mine is on mount Sicker; 8 miles by road northwest from Duncan; on Vancouver island. It includes the old Lenora; Tyee; and Richard III mines; formerly under separate ownership but now under the single ownership of Twin "J' Mines; Limited.

Jan 1, 1954

By N. Maleki

Magnesium matrix composites are widely used in automotive and aerospace industries for achieving higher performance due to their light weight. The Mg2Si intermetallics compound in Mg/Mg2Si composite exhibits many excellent properties such as high melting temperature, high hardness, and low thermal expansion coefficient. However, under normal cast conditions, the primary Mg2Si phase exhibits coarse Chinese script or dendritic morphologies and the eutectic structures is very brittle resulting in the low ductility and strength of the alloys. Modification treatment is a very effective method to obtain fine microstructure and improve the mechanical properties of the alloys due to low production cost. In this investigation various amount of bismuth addition have been carried out on Mg?5wt %Si alloy to refine and modify the morphology of coarse Mg2Si in order to improve the corrosion resistance of the composite product. The effect of Bi content on microstructure of Mg2Si/Mg composite was investigated by optical and scanning electron microscopy followed by EDX analysis and X-Ray diffraction. In order to compare corrosion resistance of unmodified and modified specimens, Immersion test and potentiodynamic polarization (PD) were used. The results showed that by Bi addition, the size of primary phase Mg2Si was considerably reduced and the morphology was modified from a coarse dendritic shape to a polyhedral shape. The results also indicated that the corrosion resistance of Mg?Si alloys was improved by the addition of 1%wt of Bi due to the reduction, refinement and evenly distribution of Mg2Si phase. Indeed, both the morphology and distribution of Mg2Si intermetallic had a great influence on the corrosion behavior of Mg/Mg2Si composite.

Oct 1, 2011

By E. Marcotte

"Technology developments and improvements are imperative to maintain a viable mineral processing industry. In order to achieve optimum implementation of technology in processing plants, safety conscious and efficient work forces are required. Effective management methods are required to prevent employee injuries, equipment or environmental damage and process losses. Good leadership also provides for employees to perform their work in the safest and most efficient manners to attain optimum recoveries of the valuable minerals and produce high quality mill products. Equipment and processes must be designed, operated and maintained as required to assure safe and efficient mineral processing.INTRODUCTIONThe Canadian mining industry must contend with many challenges to attain and maintain a competitive position in today's global market. Canadian Mineral Processors play a vital role in meeting the challenges and achieving optimum mineral productivity.Ongoing technology developments and improvements continue to be imperative to maintain a viable mineral processing industry. The efficient implementation of technology developments requires a safety conscious, skillful and productive work force.In addition to technical and human resources, challenges may also include governments, labour unions or environmental advocates who at times may appear to be misguided or unrealistic. Canadian Mineral Processors must not allow themselves to be overwhelmed by these apparent obstacles but must use their demonstrated ingenuity to achieve successful solutions.It should be recognized that the majority of the Canadian work force are, in fact, a potentially talented and skillful people with ambitions to excel. As leaders of people, we must provide the methodology, incentive and direction that will allow our work forces to realize their ambitions. If the potentials of our work forces are not recognized and leadership is not properly exercised much loss will occur. That is, safe effective and efficient work will not be achieved."

Jan 1, 1993

By Angeles Mendoza Sammet

Based on the analysis of issues associated to conflicts between communities and mining companies in Mexico, this paper suggests actions to make mining more sustainable in Mexico. Interviews with key informants and a revision of documental information available on the internet provided information on 15 cases of conflicts in various parts of the country. The issues varied from incompliance with environmental law to assassination of community members opposing mining. The analysis concludes that mining is not sustainable in Mexico. Both mining companies and the Government of Mexico can make changes to improve sustainability. Mining companies could take a proactive approach and engage in consultation with communities before starting operations. Sharing information with communities on environmental management programs and monitoring results can be a way to start building trust and demonstrate environmental commitments. Companies can implement and evaluate CSR policies to ensure that all staff and contractors are trained on them to reduce and/or prevent corruption and violations of human and indigenous rights. Only 3 of the 15 companies had clear social responsibility policies or sustainability targets, but no reports evaluating them. Complying with the law does not make a project sustainable because of corruption, deficient enforcement, and gaps in legislation. The Government of Mexico should address the following points to make mining more consistent with sustainable development. Update the mining legislation to introduce sustainable development principles and consultation. Incorporate the notion of Free, Prior, Informed Consent (FPIC) for Indigenous People (IP) on all applicable Mexican laws or regulations. The government should not grant concessions on protected areas or indigenous lands without extensive meaningful consultation with the public, IP and land owners. Finally, it is vital to increase SEMARNAT?s capacity to review impact assessment reports and inspect and monitor environmental compliance along the life cycle of projects.

Aug 1, 2013

By T. T. Chen, J. E. Dutrizac, G. Poirier

In the Waelz kiln process, EAF dust is converted to an Fe-rich slag, a (Zn, Fe)-rich dust that is recycled to the kiln and the Zn-rich Waelz oxide which is subsequently up-graded for the recovery of zinc. To clarify the reactions occurring, the Waelz kiln products from a European Waelz plant were characterized mineralogically to determine the mineral species present, their micro-textures and the metal carriers. The EAF dust contains 27 % Zn, and consists mainly of ZnFe2O4 and ZnO, together with minor to trace amounts of NaCl, PbCl2, KCl, CaO, Ca2Fe2O5, Fe203, FRO, Pb oxide and various Ca-Fe-Al-Mn silicates. The KCI and NaCI sometimes agglomerate the other particles. The slag consists of nodules which often exhibit colloform structures. The slag contains of variable amounts of Fe, FeO(OH), FeO, gypsum, Ca(OH)2, Ca2SiO4 and various Ca-Fe¬Al-Mg-Mn silicates as well as minor to trace amounts of ZnFe2O4, Cr-Fe oxide, Mn-Fe oxide and other species. The Waelz oxide contains 57-61 % Zn, and consists predominantly of ZnO, with minor to trace amounts of KCI NaCl, Pb(OH)Cl, Pb20(SO4), Pb chloride, ZnSO4, ZnFe2O4, Ca2SiO4, Ca2Fe2O5, Ca-Fe silicate and NaZn4(SO4)(OH)6Cl.6H2O. The KCI agglomerates the other particles in the Waelz oxide. The recycled dust appears to be a mixture of EAF dust and Waelz oxide, but it contains relatively more coarser-grained metallic Pb and Pb oxide particles.

Jan 1, 2004

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By M. Takebayashi, K. Takenaka, S. Matsubara, T. Yoneyama

The cathode production of Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. reached 450,000 tons per year in 2016 with three tank houses. Niihama tank house commenced operations in 1919 with conventional sheet cathode technology. Approximately 100 years of operation experience and the technical development enabled that the current density of Niihama tank house and the Toyo tank house #1 increased to 320 A/m2. These operation techniques were utilized at the Toyo tank house #2 which started in 2005, and its current density reached up to 350 A/m2 with permanent cathode technology. In order to achieve high current efficiency under condition of 350 A/m2 operation at Toyo tank house #2, continued efforts had been made to verticality of anodes and permanent cathodes. To improve verticality of anodes and cathodes, reduction of short circuit ratio by changing the shape of the anode, optimizing the anode pressing machine and off-line process for rectifying the distortion of permanent cathodes was carried out. In addition, concentration control of electrolyte and expansion of Ni removing ability from the electrolyte prevented passivation. Finally, more than 96% of the current efficiency was stably confirmed. INTRODUCTION Today, Toyo Smelter and Refinery of Sumitomo Metal Mining operates three tank houses in Japan, namely, Toyo tank house #1, Toyo tank house #2, and Niihama tank house with a total capacity of 450,000 metric tons of copper cathodes. Figure 1 shows the trend of cathode copper production and the current density at three tank houses over the last 10 years. Cathode production by Toyo Smelter and Refinery reached 450,000 tons per year in 2016 with three tank houses.

Jan 1, 2019

By G. A. Sutton

This paper, describes a case example from San Manuel mine, where in situ copper leaching of the supergene zone was done over a 14 year period (1986–1999) in conjunction with underground and open-pit mining operations of a copper porphyry deposit. In 1993–1994, testing of well fields was done to determine the amount of copper that would be recovered from in situ leaching of the supergene zone, which was composed primarily of chrysocolla and copper-clay minerals. It was determined that the leach fluid would reach 70% (‘sweep efficiency’) of the copper minerals and that 75% of them would be leached for a recovery of 52% of the acid soluble copper. However, the final results from Zone 6, which had the longest leach history, showed that approximately 42% of the acid soluble copper was recovered, indicating that the `sweep efficiency’ was closer to 55%. Comparison of drill-core assay data from two holes, one drilled before (ARM158) and the other after (SMO9607) leaching, also indicate that approximately 42% of the acid soluble copper was recovered. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to a combination of factors, including difficulty in maintaining fluid saturation, channeling effects and gypsum precipitation. INTRODUCTION In situ copper leaching at the San Manuel mine, Arizona, was initiated in 1986. It was recognized that some of the copper oxide resource was not going to be economically recoverable by conventional open pit and heap leach methods using solvent extraction and electrowinning (SXEW). A high stripping ratio would be required to access part of the resource. At the time, in situ leaching was becoming popular in the uranium industry but the approach was virtually unknown in the copper industry, especially not at a large scale.

Jan 1, 2019

By Jianzhong Liu

Based on the characteristics of overburden rock strata movement, surface ground subsidence and casing deformation and failure, a tension-shear combination failure model of surface borehole was set up. The main controlling factors of the mining-induced deformation and failure of surface borehole were researched with this failure model and the limit analysis method. The mining methods and geology conditions mechanics action mechanism to surface borehole and its time ?space evaluation rule was found. The surface borehole deformation and fracture rule were advanced. It provides theoretical support to optimizing layout, structure type, security measure and local casing protection of surface borehole.

Aug 1, 2013

By Z. D. Hora

Brick shales and refractory clays are mined at Sumas Mountain near Abbotsford. Sholes and stoneware clays elsewhere in the province have not been developed. THE SUMAS MOUNTAIN deposit near Abbotsford, 80 km east of Vancouver, has been in continuous production since 1905. The deposit is exposed in a small outlier and comprises a sequence of alternating beds of clay and sand. Beds are of Eocene age. Within the 400 m thick ness of sediments are seven distinctive conglomerate members, some up to 20 m thick, interbedded with fine grained sediments including claystones and siltstone , or "shales". Shale is quarried to produce a variety of bricks, sewer pipes and similar products; it is also used for cement. Several different shale beds have been mined over the years and exhibit a variety of fired colours ranging from buff-pink grey to deep red; pyrometric cone equivalents (PCE) range from 3 to 20. A layer of fireclay 3 to 4 m thick that occurs at the base of the sequence has pinkish white to light buff fired colour and PCE of 30 to 33. It is used as a 266 primary component to produce refractory bricks. The shale is quarried and processed by Clayburn Industries Limited of Abbotsford. Another similar but smaller outlier of the same geological formation is known from Blue Mountain, about 20 km northwest of Mission. Other ceramic clays in British Columbia are reported from Quesnel (7 m bed of white stoneware clay, PCE 17 to 19), Giscome Rapids (25 km north of Prince George, 10 m bed of stoneware clay to PCE 31) and anaimo-Comox area (buff to red firing "shales", PCE 8 to 10-1 12) . From 1959 to 1974 Cretaceous shale from Saturna Island in the Strait of Georgia was used to produce lightweight aggregate. Similar deposits of expanding shale are known from the vicinity of Duncan on Vancouver Island.

Jan 1, 1984

By Steven Dempsey

Overview What is Tubbing? A look at Cigar Lake Tubbing Design The Tubbing Installation Backwall Grouting

May 1, 2013

By Z. D. Hora

Several deposits of crystalline magnesite are known in southeast British Columbia. Deposits at Cross River and Marysville have been thoroughly explored, but as yet there has been no commercial production.

Jan 1, 1984

By R. O. Burt, R. W. Bruce

"IntroductionGravity concentration, the separation of two or more minerals due to the difference in their relative specific gravity and usually in a fluid medium, is the oldest recorded form of mineral processing.The principles of gravity concentration were known to, and practiced by, the ancients and Hoover's commentary to De Re Meta/lied'' notes many early references.Over the centuries, as direct smelting ores became more and more uncommon, the mineral processing industry developed and along with it many varied methods of concentration. Gravity concentration declined rapidly in importance in the early twentieth century, and it is only in the last decade that its advantages are being re-evaluated.A significant proportion of ores are processed by gravity; a large proportion being in the iron and coal industries<'>, or in the treatment at very high volume of relatively coarse alluvial deposits. The tin dredges of South East Asia and Beach sand plants of Australia are prime examples.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive.Principle of Gravity ConcentrationGravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air.The relative movement of minerals to one another is achieved by a variety of methods. These are: separation in a fluid of intermediate density (heavy media separation); by stratification (such as in jigging); in a flowing fluid (cones, spirals, sluices etc.) and with a horizontal shear (shaking tables etc.)."

Jan 1, 1989

By J. S. Scott

"The Quemont property comprises 640 acres lying directly north of and adjoining the Noranda (Horne) mine. During 1926 to 1928, United Verde Extension Mining Corporation sank a shaft 235 feet and did 3,000 feet of development work on the 215-foot level. Between 1929 and 1930, Quemonr Mining Corporation deepened the shaft to 926 feet, and did further lateral work and drilling on the 500- and 900-foot levels. This work was confined to an area close to the south boundary and met with little encouragement.Following a period of idleness a magnetic survey was made in the winter of 1944, followed in the summer of the same year by some 6,000 feet of drilling. The first successful hole was drilled in February, 1945, from the ice of Osisko lake.To the time of writing, 131,000 feet of drilling, surface and underground,have indicated a large tonnage of gold-silver-copper-zinc ore, and although some knowledge of the geology and structure is emerging, it is too early to draw definite conclusions. The following brief description deals only with those structural features that are reasonably well indicated."

Jan 1, 1954

By Victor Dolmage

"The localization of orebodies by geological structures is well demonstrated at the Copper Mountain mine of southwestern British Columbia. These extensive deposits; owned and workd by the Granby Consolidated Mining; Smelting and Power Company; are at Princeton; abo!lt 150 miles east of Vancouver and 40 miles north of the International boundary. The geology of the deposits and the surrounding district is described by the present writer in Memoir 171 of the Geological Survey of Canada; pub1ished in 1934.The main geological feature is a gabbro stock, elliptical in plan, with a major axis about 5 miles in length extending in a northwest-southeast direction. The stock varies in composition from syeno-gabbro (gabbro plus orthoclase) through diorite and syenite to a core of syenite pegmatite. All the members contain orthoclase, which ·increases greatly in amount toward the centre, but all are devoid of quartz. The stock has been injected into a steeply folded series of volcanic flows, breccias, and tuffs that strike more or less parallel with the major axis of the stock. On its northeast side the stock is flanked by a band of fairly coarse volcanic breccia of andesitic composition and ·having fragments up to several inches in length. Where this breccia is tangential to the stock it is both dynamically and chemically metamorphosed to a marked degree, and within the zone of this metamorphism are enclosed the copper deposit~. The ore consists of bornite, chalcopyrite, and a little magnetite occurring as disseminated grains and small veinlets in the metamorphosed breccias. The only gangue minerals are orthoclase, albite, oligoclase, and biotite. The two most common vein minerals, quartz and pyrite, are conspicuously rare or absent. The dynamic metamorphism has produced two well-defined structures, namely, a strong schistosity parallel with the curved vertical contact of the stock and a very striking set of small, straight, nearly parallel open fractures that stand nearly vertical and at right angles to both the schistosity and the stock contact. These are called the ore fractures."

Jan 1, 1954

By H. R. Kempthorne

"The Property of Bevcon Mines Limited, including a recently acquired adjoining south group, occupies an area of 2,625 acres in northeast Louvicourt township, Abitibi county, Quebec. It is situated 17 miles east of Val d'Or at the junction of provincial highways 58 and 59.Gold was first discovered in the area in 1931 by the late S. B. Jowsey on the present property of Buffaddison Gold Mines adjoining to the west. However, it was not until the winter of 1944-45 that diamond drilling encountered encouraging results on the Bevcon claims. During the period 1946-1948 a shaft was sunk to 1,000 feet and considerable development undertaken from the 500-foot to the 1,000-foot levels. Between 1947 and 1950 approximately 24,000 tons of dump ore and 48,000 tons of ore by stoping were milled at Perron Gold Mines. The favourable results of these tests prompted the decision to construct a milling plant at Bevcon. The mill began operating in July 1952, and presently has a capacity of 800 tons per day. In 1953 the shaft was deepened to 1,600 feet and is currently (1955) being driven to 2,225 feet.Total production of gold to the end of 1954 has been 101,024 ounces from the milling of 697,427 tons of ore of an average grade of 0·163 ounces per ton.GeologyThe Bevcon orebodies occur in a granodiorite stock which has an east-west length of approximately 4 miles and a maximum width of 1 1/2 miles. The property covers the central portion of the stock and its contacts with the Keewatin volcanics. Approximately one-third of the northern contact and one-half of the southern contact are contained within the Bevcon claims. The granodiorite has been cut by acid (feldspar porphyry) and basic dykes trending east-west. A younger diabase dyke, 300 feet wide, strikes northeasterly across the property 1,000 feet east of the shaft.The main ore zone, striking east-west, lies between the more northerly porphyry dyke and the north granodiorite-greenstone contact. It has been extensively sheared, fractured, altered, and mineralized by gold-bearing solutions. It is approximately 2,000 feet Jong from the west boundary towards the diabase dyke. The shaft is centrally located and passes through the south contact of the ore zone at the 500-foot level. The zone increases in width and trends northerly with depth, due to the porphyry and greenstone contacts having average dips of 80 degrees and 70 degrees respectively to the north. Thus on the uppermost or 500-foot level the width is 150 to 200 feet, and at the present bottom level at 1,600 feet the width is 400 to 500 feet.Another gold-bearing zone has been indicated 200 to 400 feet south of the main ore zone by limited surface drilling."

Jan 1, 1949

By Jean A. Bastien

Cette présentation décrit les étapes de développement et l?exploitation souterraine au puits Penna chez Agnico-Eagle division Laronde. Les sujets suivants sont touchés : le fonçage du puits, le développement des niveaux, la méthode d?exploitation, la manutention de la roche brisée, le méthode de remblayage et la ventilation. En résumé : le fonçage du puits s?est fait sur 2,240 mètres de novembre 1995 à mars 2000. Le développement des niveaux a débuté en octobre 1998. Les opérations de minage ont débutés en août 99 dans le premier horizon situé au dessus du niveau 122. Les chantiers sont exploités par longs-trous d?environ 25 mètres de long avec un diamètre de 10 cm. Les accès à la zone minéralisée sont transverses. Le minerai est soutiré des chantiers et acheminé au passe-minerai a l?aide de chargeuses navettes. Par la suite, le minerai passe sur un marteau, est concassé et transporté sur un convoyeur, jusqu?au silo de 4,500 tonnes au-dessus de la station de chargement automatisée du niveau 152 d?ou les skips sont alimentés. Le remblai en pâte est envoyé de la surface par des trous ayant un revêtement d?acier. Le diamètre intérieur est de 15 cm. Le réseau de ventilation est principalement alimentée par des ventilateurs de surface (système aspirant et souflant) conçus pour acheminer sous-terre un maximum de 640 mètres cubes par minutes (1,350,000 pcm).

May 1, 2001

By C. Barnett

"The mill at Noranda Mines Limited, Geco Division in Manitouwadge, Ontario went into production in 1957 treating 3,500 tons per day of copper, zinc, silver, lead ore. It was not until 1964, however, that the zinc concentrate drying plant was constructed. In 1970, milling capacity was increased from 4,000 to 5,000 tons per day. The zinc content of the ore is quite variable so that the tonnage of zinc concentrate dried varies from 200 to 650 tons per day.The drying plant was designed to dry 25 tons of zinc concentrate, dry basis, per hour from an initial moisture of 8.5% to a final moisture of 2%. Major components were selected so that capacity could be increased to 35 tons per hour with minor modifications.The rotary dryer is a Hardinge type ""XH-12"" with a diameter of 80"" and a length of 50 feet. The all welded construction shell is 1/2 inch thick mild steel plate with 3/4"" thick reinforcing bands under the tires arranged for operation at a slope of 1/2 inch to the foot. The 3/8"" x 12"" radial flights are welded to the shell. There are no flights in the last ten feet of the shell in order to reduce dusting. This unit is driven by a 50 HP motor through a Hamilton type CD250 double reduction helical gear speed reducer. The shell speed is 5.8 RPM.The standard Peabody horizontal air heater has a rated capacity of 10,000,000 B.T.U. 's/Hr. The combustion chamber is lined with high temperature refractory brick and is air cooled. The conical outlet section of the air heater is lined with insulating fire-brick. The burner is a type AT wide range mechanical atomizer fired by a type ""CR"" gas-electric ignitor.The Bunker ""C"" fuel is supplied by a Compower duplex pumping, heating and straining unit, including tank hotwell, Powertronic oil line heating system with a 550/24 volt transformer."

Jan 1, 1972