Search Documents

By Kousuke Takahata, Hirofumi Yoshimura, Jun Nakahigashi

Studies of a protium treatment for grain refinement of a + ß type titanium alloy are reviewed and recent experimental results are introduced. Protium treatment consists of the following three processes: (1) protium absorption, (2) martensitic transformation and hot working, and (3) final treatment for protium desorption and recrystallization. A combination of these processes results in the ultra-fine grains of 0.3 to 0.5 µm in diameter with high angle boundaries. The ultra-fine-grained material exhibits superplastic elongation of over 9000%. Superplastic forming was successfully used to fabricate a denture base. These materials may be widely applicable as biomaterials in various medical industries.

Jan 1, 2004

By Y. Dong, L. Li, L. Yu

Converter slag has become an important secondary raw material. Consequently, vanadium bearing converter slag is of great interest for the recovery of vanadium. Solidified converter slags are made up of three main mineral components: dicalcium silicate, calcium ferrite and wustite. Vanadium in modified slow cooling down converter slag of Magang is found mainly concentrated in a separate mineral phase. The mineral phase with high content of vanadium (24%, wt, V205), concentrating 83% of vanadium, can be separated from the slag for economical vanadium recovery. Some characters of the mineral phase were discussed comparing with dicalcium silicate, one of the typical mineral phases in converter slag studied well.

Jan 1, 2004

By A. Yoshida, H. Miura, S. Yamaguchi, Y. Oyama

A discussion is given on the ionic equilibria and precipitation reactions in seawater based on thermodynamic analysis, in order to understand the solubility of nutrient salts from dephosphorization slag for marine phytoplankton. Solubility of constituent ions in aqueous solution in equilibrium with solid phases are determined using thermodynamic data. It is proposed that CO2 potential defined as log Pco2 should be considered as an additional parameter to the Eh- pH diagram for the ionic equilibrium of slag components in seawater, since magnesium and calcium carbonate precipitation reactions determine the solubility of ligand ions in nutrient salts, such as phosphates, silicate, and sulfate.

Jan 1, 2004

By J. Aguilar-Santillan, H. Balmori-Ramirez, R. C. Bradt, I. Vernet-Patiño, F. Cunha

Kyanite is an alumino-silicate mineral that has been widely used for the production of refractory products for industrial applications. Kyanite provides a high alumina content, it readily produces mullite during firing, good hot strength of products and can be adapted to produce dimensional stability of products during firing. This research addresses the application of kyanite in mixes to produce (0 dense mullite aggregates with the addition of alumina, (ii) dense composite refractory aggregates of forsterite / spinel with additions of magnesia, and (iii) dense cordierite aggregates with the addition of talc. Effects of attrition milling and conventional ceramic processing are addressed as they affect the properties of these unique aggregates.

Jan 1, 2004

By G. Tozsin

A six-stage sequential leaching procedure was used to assess the leachability of heavy metals from waste rock in Antamina Mine. Sequential extractions procedure is well established for fine and small (? 1g) samples. However procedures for coarse and large test samples are lacking. This study presents results of the sequential leaches tests conducted on relatively coarse and large representative samples in terms of the availability and mobility of metals. Selective chemical reagents were used to extract metals from six different fractions where metals released with each subsequent extraction are believed to be bound tighter than those released in prior steps and therefore less likely to be leached.

Aug 1, 2013

By A. L. Williamson

Bio-mining is a cost-effective, energy efficient and potentially environmentally protective method of exploiting a variety of ore deposits, from high-grade base metal deposits of nickel to lower-grade uranium and rare earth deposits such as are found in the uraniferous quartz-pebble conglomerate beds of the Quirke Syncline, Elliot Lake, Ontario. The effectiveness of bio-mining in Elliot Lake depends on the success of bacterially-influenced dissolution of metals of economic importance. The determination of both the dissolution efficiency and rate controls for uranium and rare earth elements from bio-extraction processes is critical to assess the potential for success of bio-mining along the Quirke Syncline. This poster provides an overview of proton-mediated biogeochemical dissolution of more than 50 elements, including uranium and rare earth elements from samples of the low grade uraniferous ore collected as drill core from the Elliot Lake area. The elemental data is quantified using advanced spectroscopic tools (ICP-MS and ICP-AES) to analyze solutions obtained from a series of environmentally controlled biologically-mediated uranium ore extraction experiments. The findings are being to guide design of larger scale bio-leaching experiments to further assess the potential for success of bio-mining along the Quirke Syncline.

Aug 1, 2010

By P. R. Stephenson

Mining projects depend on the amount and quality of the mineral reserves, which in turn depend on the amount and quality of the mineral resources. Only Measured and Indicated Resources may be converted to mineral reserves and Inferred Resources may not, with certain exceptions, be used in economic studies. Responsibility for the estimation of mineral resources rests with the Qualified Person (QP) and there is a wealth of literature, text books and case studies to guide the QP. Responsibility for the classification of the mineral resources also rests with the QP. While there is some industry guidance and common practice on approaches to resource classification on which the QP can draw, the process is (or should be) heavily dependent on the exercise of judgement by the QP. However, this inevitably leads to situations where, for example, one QP?s Inferred Resource is another QP?s Indicated Resource. If the QP?s judgement is poorly reasoned or illogical (as is sometimes the case), it can have a major impact on the project, often with substantial cost or value implications. Project managers and company executives should not unquestioningly accept QP?s classification decisions and should apply the same intensity of due diligence that they apply to other critical elements of the project.

May 1, 2011

By E. You

Kennecott Utah Copper Refinery and Outokumpu Technology have developed a wireless Electrolytic Cell Monitor (CellSensor) system to monitor cell voltage and temperature. The system is based on a robust self-organizing and self-healing wireless network with a very reliable redundant structure. The microprocessor controlled CellSensor device operates off a small amount of energy harvested from the cell bus and requires no external power source. The radio works in the 2.4 GHz international ISM band using robust Spread Spectrum technology. The CellSensor does not require end user calibration of either the voltage or temperature sensors and accuracy is superior to previous systems. The on-board computation power allows digital filtering of the cell voltage signal which results in very high quality data. The system requires much less maintenance than conventional hardwired systems and is intrinsically safer since no high voltage isolation is required. The advanced diagnostic functions allow the device to determine if the bus tap contact is degrading. The CellSensor can also be used for monitoring electrowinning (EW) cells for a variety of metals. CellSensor have been tested for over two years at the Kennecott Utah Copper and Boliden Harjavalta Pori refineries. The CellSensor system is now commercially available through Outokumpu Technology.

Jan 1, 2007

By Muhammad Zaka Emad

Cemented rockfill (CRF) plays a vital role in pillar-less mining. Many factors are associated with optimum design of a CRF material. Factors like strength, placement method, mixing, curing time, water content, binder contents, binder composition and additives require to be studied for appropriate rockfill design. The most important factor is strength of a CRF. The design engineer considers fill strength requirements (FSR) for the estimation of CRF strength requirements. Inappropriate CRF strength can cause excessive ore dilution. The recent studies on CRF practices at some of the Canadian mines revealed the most common flaws. Comparison of different types of fill determined that most of the failures occur in cemented rockfill, and the compressive strength can be improved by small addition of sand and mine tailings. This work discusses the studies on determination of unconfined compressive strength, Young?s modulus, density and water contents of CRF being placed in the excavated stopes. It was found that the CRF properties were largely influenced by the variation in gradation and curing time. The 7% binder content improved compressive strength of rockfill significantly but it has an influence on the economics, whereas 4% and 5% binder contents are better choices. The maximum Young?s modulus values were obtained at 28 days curing time for most of the samples.

May 1, 2011

By Laurier Juteau

"NOT TOO LONG AGO, the CIM Education Committee saw the need for an information campaign to promote interest in mineral industry careers among young people. Today, times have changed and the Committee has now placed emphasis on the definition and function of the mining engineer. This situation, we believe, is entirely normal and the change of emphasis is not due to a change in the needs of the industry but more to a diversification of these needs. In years past, the Canadian mineral industry, although a very important part of our economy, was looked upon as a specialized craft and, because of the richness of our resources, did not suffer too much from competition. Now, times have changed and we are increasingly at the mercy of the competition and damaging inroads of price fluctuations, etc. We will therefore answer the questions raised in this discussion in the light of the role played in the past and the role to be played in the future by the Canadian mining engineer. We will begin with the following premises : (a) If mining engineers are to be involved in the massive problems of society, their traditional background is not sufficient. (b) Councils for professional development are working on criteria for the accreditation of advanced degree programs in the United States as well as in Canada, and, simultaneously, three-year technology programs are being developed along with professional engineering degree programs. (c) The difference between European and American industries regarding philosophy of life is that in Europe they appreciate wisdom more than HPs while in America the HP seems to be more important. The Engineering Digest of February 1972 reported that in the United States, during June and July of 1971, the second highest rate of unemployment was for the 55 to 64 age group ( 4.1 per cent). This survey certainly applies to Canadian industry as well. (d) Degrees to be awarded in Canadian universities and technical schools in 1972 will be:"

Jan 1, 1972

By Angela L. Paveley

Economic viability of base metal mining is complicated by a volatile market that can cause fluctuations in the growth and stability of the mining industry. Nickel is mined primarily for use in manufacturing industrial stainless steel and plating materials. It is essential that nickel production be sufficient to respond to current and future market demand. A Post-Pillar cut and fill mining complex is currently producing nickel sulfide in Northern Manitoba. From 2006 this area has shown a steady increase in the annual production, rising from 11 million pounds to 25 million pounds in 2010, and accounting for 33% of the total production for the Manitoba Operations. It is expected that fine-tuning the mining process can safely enhance ore recovery, improve production consistency, and increase economic viability of the deposit. The Post-Pillar Optimization study was initiated by the local technical and operational departments at the mine and analyzed from July 2010 to March 2011. The purpose of this study was to determine if portions of non-recoverable pillars can be slashed without jeopardizing pillar strength. This ideal case would optimize ore recovery and reduce variability in the ore mining rate. Numerical modeling and geo-mechanical material properties analyses, completed by the rock mechanics group, define the maximum drift width at 32 feet and the minimum pillar width at 18 feet. Thus, it was suggested that up to 3 feet could be slashed from two sides of the standard 24 foot pillars without damaging ground integrity. The field data collected indicates that additional ore could be recovered without compromising the safety of the workplace and the integrity of the complex. Consequently, technical and operational groups work jointly to achieve pillar optimization. Approximately 500,000 pounds of nickel was extracted from the complex via pillar optimization from July 2010 to March 2011. Economic analyses show the pillar optimization method developed for the mining complex is a proven, value-added opportunity. The mining complex remains a safe workplace and has retained ground integrity.

Nov 1, 2011

Unplanned open stope hanging wall dilution is a significant cost for many open stope mining operations. Significant advances in empirical and analytical approaches for estimating stope dilution have been made, however, many important factors are still either ignored or assessed in purely subjective terms. There are many hard to quantify factors that simultaneously influence opening stability and dilution. This creates a significant difficulty for determining the influence of a single variable, such as exposure time, on opening stability. Open stope exposure time has been found to be one of the important factors that influences overall stope stability and dilution. A study is currently being conducted to quantify many of the factors influencing open stope dilution. The assessment of a large comprehensive case history database of Hudson Bay Mining and Smelting Co. Ltd. (HBMS) operations forms the basis of this study. This paper presents the findings of a study on the influence of stope exposure time on open stope dilution. The study is based on applying existing empirical stope dilution prediction methods to the extensive HBMS database. Minimising stope mucking time has been recognised as a method to significantly reduce stope dilution. Factors which influence hanging wall dilution, such as drill and blasting methods as well as undercutting the hanging wall, have been applied to reduce the scatter in the database. Empirical design techniques based on rock classification attempt to relate opening stability to ?stand-up time?, however, these approaches have not frequently been applied to the mining industry. Data from a ?stand-up time? graph have been interpreted in terms of an equivalent average depth of hanging wall slough and compared to the HBMS database findings. To add to the existing HBMS database, several stope case histories have been taken from Geco mine. These cases include data from very large open stopes with long exposure times. Data from all three sources suggest that hanging wall slough increases between .14 and 0.3 metres per month for a rock mass Q? value between about 4 and 13.

May 1, 2003

By Abdurrahman Tosun

It is very important for after blasting processes that muck pile fragmentation is predicted and controlled during blasting. Therefore, a significant research effort has been devoted to the development of mathematical equations that predict the value of average muck pile fragmentation. The specific charge parameter used in all of these equations is determined as the ratio of the total mass of explosives used to break a volume of rock. The length of blast surface and the row number of the blasthole are ignored in the calculation of the specific charge. However, in a blasting operation, blasthole geometry may result in additional material being impacted by a blasthole. This is due to effect shares of in both end sides of blastholes and the back region of blasting surface. In this study, a total of 14 blast tests, 8 at the first quarry and 6 at the second quarry of the Bati Anadolu (Western Anatolia) Cement Factory, were performed. In each study area blast tests were designed in the same direction continuously to provide stable structural properties of the rock. Therefore muck pile fragmentation depended on only specific charge values for each blast tests. Specific charge values were calculated according to both an average blasthole and also the total volume of material occurred as a result of blasting for each blast tests. During loading until the end of blasted material the front, the back, the arm off and the bucket off pump hydraulic pressure values occurred in hydraulic pistons of the loader were determined with a lot of data received for each blast tests. After that the relationships between specific charges values obtained according to two different methods and hydraulic pressure values of the loader were established with two correlations. The relationships between specific charges values obtained according to the total volume of material occurred as a result of blasting and hydraulic pressure values of the loader occurred as the best results especially the blasting operations that have the total length of blasting surfaces are short.

Aug 1, 2013

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A 'timber car' that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By R. H. Duval

"In May 1936, Pamour started producing gold by cyanidation of flotation concentrates, and in 1939 was milling about 1, 600 tons per day.Refining records dating from 1939 show two oil-fired furnaces in use, (Rockwell type 46 11 x 29 11 inside oval shell).Refining time averaged 7. 83 hours during the year 1939, indicating a complete refining shift of about 9. 33 hours. That year appears to be characteristic of the period with regard to time required and results obtained.For that year total fineness (gold + silver) of the bars averaged 940 (approx.), but it frequently dropped below this figure, sometimes far below.Furnace lining life varied widely from three to seven or more months. Sillimanite was the standard lining but Mullfrax 41 was frequently used.For many years refining practice remained practically unchanged, and in 1960 procedure still consisted essentially of mixing a flux(% Composition Borax 41, Silica 11, Soda-Ash 11, Nitre 15, Mn02 22) with cyanidation precipitate in the ratio of l. 2 to l and heating to a medium heat (yellowishred, 2000° F) with a low flame for a long time. Time required was about 10. 5 hours per refining. Results were still much as detailed above.At this time it was decided to revise refining procedure, in an effort to shorten refining time and obtain consistently good bullion fineness."

Jan 1, 1965

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By H. Dundar, C. Dzomeku

An extensive testwork was performed around the HPGR plant at GoldFields Ghana Limited Tarkwa Gold Mine. The HPGR was used to prepare the feed for heap leaching. The circuit was configured in such a way that the edge material from the HPGR discharge was recycled for further crushing while the product from the centre reported to the heap leach section. The set-up of the Polysius HPGR provided an opportunity to study the effect of different design and operating variables. This paper will discuss the results from the tests performed to assess the effect of rolls’ speed and applied pressure on the capacity and the grinding efficiency of the HPGR. Applying different pressure values appeared to have an influence on the amount of edge material recycled.

Jan 1, 2012

By Renaud Cousin

Supported gold catalysts were prepared by Direct Anionic Exchange on an alumina support and tested during the reaction of CO oxidation and of saturated and unsaturated hydrocarbons (C1 to C3). The catalysts showed high activies over a range of concentrations and temperatures compatible with an application to automotive exhaust cleaning. Furthermore, a complete resistance to thermal ageing at 600°C in the absence or presence of water was observed due to the obtention of strongly anchored nanosized gold particles during the preparation step.

Oct 1, 2003

By Michael Sudbury

Introduction The essence of a good presentation is said to be: Outline what you are going to say Say it Summarize what you said This is perhaps especially good advice at 8.30 a.m. So here goes: This is an attempt to put numbers on three inextricably linked subjects: People and the Future Irrigation and Agriculture Mine Water and Mine Waste

May 1, 2013

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008