Search Documents

By T. L. Carpenter

"The presence of excessive water in the Gibraltar East Stage 1 pit initiated studies into the ground-water conditions that might be expected in mining the Granite Lake and Pollyanna pits. Hydrologic information obtained from a pump test program in 1974 indicated that deep-well dewatering could be successfully achieved. In 1976, a deep-well dewatering system consisting of eight wells was installed on the periphery of the Pollyanna pit . it has been responsible for a significant decrease in mining costs.This paper presents a brief summary of the engineering principles involved in the design of the Gibraltar dewatering system and the problems encountered in the installation and operation of deep-well pumps. IntroductionGibraltar Mines is an open-pit copper-molybdenite mine located approximately 230 air miles north of Vancouver in the central interior of British Columbia (Fig. I). The property consists of three separate major orebodies; Gibraltar East, Granite Lake and Pollyanna (Fig. 2). Mining commenced during the summer of 1971, in the Gibraltar East Stage 1 pit. The Granite Lake Stage 1 pit was mined from mid 1974 to mid 1976. The Pollyanna Stage 1 pit is currently being mined and the Gibraltar East Stage 2 is being developed for production. This report is intended as an outline of the studies and tests leading up to and including the installation of the Pollyanna pit dewatering system, the problems encountered and the results obtained.GeneralIn the summer of 1973, mining in the Gibraltar East pit progressed below ""daylight"" on the down-hill side and ground water very quickly became a costly nuisance in the day-to-day mining operations. Mining, maintenance and blasting costs reflected these problems. Concern was also voiced about adverse effects of ground water on pit wall stability. This concern later became a reality in the Gibraltar East and Granite Lake pits. A study was initiated to investigate various methods and costs of dewatering the pit areas. The study included in-pit sumps, deep peripheral wells and a drainage gallery system located below the pits."

Jan 1, 1980

By A. Bauer

The correct application of large crater blasts in unfrozen tar sand is an effective means of resisting frost penetration during winter. This results in much higher productivity and considerably less down time with excavators during winter operations. The resulting flatter angle of repose of the highwall has readily been accommodated with slight modification to bucket-wheel excavator operating procedure. Other mining schemes call for large draglines to be located on top of the highwall, which can be as high as J80 feet. The question now arises as to the effect that blasting might have on the stability of such a situation in which the highwall includes potential planes of weakness. This paper applies blast vibration data from large-scale blasting in tar sand to the stability analysis for typical production situations likely to be encountered and indicates safe scaled distances to be employed between dragline and blast.

Jan 1, 1979

By R. G. L. McCready, Marco Zentilli

"Brogan coal containing mean averages of 6,93% w/w total sulphur (1.1% sulphate sulphur, 1.6% organic sulphur and 4.24% pyritic sulphur) and 16.34% mineral ash was used as the test coal in these studies.Shake-culture leaching studies on seven size fractions of the coal, ranging in size from 0.045 mm to 1.7 mm, showed that the rate of pyrite leaching was inversely proportional to the particle size. As the use of continuous stirred tank reactors would be uneconomical for the reclamation of waste coal, column leaching studies were initiated on coal sieved to >6.35 mm to < 12.7 mm, The leachate was monitored for all metal ions and the release of iron was used to monitor the rate of pyrite oxidation . Measurable amounts of Zn, Co, Ni, Mn, and V, all of which can replace iron in the pyrite crystal structure, were released during the initial stages of leaching. Further, high concentrations of AI, Ca and Sr and trace amounts of Sn, As. Se, B, Ca, Cr, Si, and Ti were detected in the column effluents.These studies suggest that bacterial leaching will remove the pyrite and qualitative amounts of environmentally undesirable trace metals from the coal if such a process is developed for waste coal reclamation.IntroductionIn 1947, Colmer and Hinkle showed that acid mine drainage was the result of an oxidative attack of the iron-mineral sulphides by Thiobacillus ferrooxidans to produce sulphuric acid . Ashmead (1955) proposed the use of these organisms to desulphurize coal , but the subsequent research effort was concentrated on the metabolism and physiology of these extreme acidophiles.A limited number of studies have been reported on the bacterial leaching of pyrite from coal (Silverman et al., 1963; Dugan, 1977). However, the bacterial oxidation of pyrite is a self-limiting first-order reaction, probably due to the precipitation of Fe(OH)J and elemental sulphur , which progressively inhibits intimate contact between the bacterial cells and the sulphide-mineral surface. Consequently, the best pyrite oxidation experiments with coal reported to date required five days to remove 97070 of the pyrite (Dugan &Apel , 1978) using mixed cultures of T. ferrooxidans and T. thiooxidans."

Jan 1, 1985

By D. Perednis

Fuel cells with thin samaria-doped ceria (SDC) electrolyte films deposited onto an anode support using spray pyrolysis were fabricated. The SDC films were deposited onto porous NiO-YSZ substrates at deposition temperatures between 400°C and 450°C. The influence of process parameters such as deposition temperature, flow rate, type of salt and salt concentration on the quality of the film was studied. A smooth dense film was successfully deposited using the precursor cerium ammonium nitrate and samarium nitrate dissolved in butyl carbitol (33.3 vol.%), 2-methoxy-l-propanol (33.3 vol.%), and ethanol (33.3 vol.%) solvent mixture. A deposition rate of 125 nm/h was achieved.

Jan 1, 2005

By Lionel C. Kilburn

"This geological engineering method is based on jour main characteristics of mineral properties, viz; location: inclusion of valuable mineralization; inclusion of geophysical and/or geochemical targets; and inclusion of geological targets. These are subdivided into a total of 19 subcategories, which are used to determine the value of the property.The nineteen subcategories are prioritized and assigned relative value factors from 1.3 to 10. Value of each mineral claim unit is determined by applying the appropriate subcategory factors to a base value of $400per 16.2 hectare unit. Property value is calculated by totalling the values of such individual claim-units.The boundary between ore grade and sub-ore grade must be estimated for each property under valuation, thereby making the method sensitive to mineral commodity prices.A clear and disciplined sequence of decisions based on personal experience forms the basis of this method. The method utilizes all factors normally used to value a mineral property.IntroductionIt is generally accepted in the exploration industry that valuation of exploration properties is a subjective rather than objective process (Roscoe, 1986; Lawrence, 1988; Lawrence, 1989; Woodcock, 1985), and that it is greatly influenced by the experience and qualifications of the person who is doing the valuation. However, the significantly low degree of objectivity in mineral property valuation at this point in time invites effort to achieve a more quantitative engineering basis.Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand , and political-economic conditions, all of which vary with time. Therefore, any valuation is valid for only that point in time when it is made. Mineral deposits can decrease as well as increase in technical value with time."

Jan 1, 1990

By M. K. Gangal, A. E. Hall, S. B. V. Stewart

"An investigation into the problem of atmospheric fog in Canadian mines is described. Fog occurs in several mines and the reduced visibility can result in the closure of workings for safety reasons. Information on the mechanisms of fog formation are discussed and the methods for improving conditions are reviewed with their relative costs.INTRODUCTIONAtmospheric fog occurs in several Canadian mines during spring and summer. The fog which reduces visibility, contributes to loss of production and increased accident risk . Closure of ramps in mechanized mines causes mining to be stopped or rescheduled, and stoping and grade control may be affected . Increased corrosion of equipment may result from acidic fog .Fog is commonly caused by saturated air being compressed and heated by an inlet fan and then being circulated in an ascensional system with heat transfer to the walls of wet airways. This causes supersaturation and water droplets condense to create fog, with liquid water contents of 0.5 g/kg to 3 g/kg of air. These concentrations reduce visibility to less than 10m and prevent mining. Less severe fog is usually tolerated as a nuisance, about which little can be done."

Jan 1, 1989

By W. G. Brown

"Review of prototype testing of two types of three-phase, argon stabilized reactor/furnace indicates specialized advantages for both, as compared with existing metallurgical furnace technology. They are: the direct-arc, plasma-torch furnace (Knipp); and the indirect, plasma extended-arc reactor (PEAR), developed at the University of Toronto.IntroductionA unique type of three-phase AC, plasma extended-arc reactor, (PEAR), shown in Figure la with gravity feed, has been undergoing development at the University of Toronto, during the past fifteen years: argon gas, introduced axially through drilled-holes in ordinary graphite electrodes, increases the length of indirect arcing and improves electrical stability while decreasing electrode consumption as compared with the performance of AC electric arc furnaces (EAF &apos;s). Meanwhile and independently, a three-phase, transferred arc plasma furnace (Fig. 1b) has been developed by the Krupp Research Institute in Germany, using argon-stabilized, water- cooled plasma-torches with thoriated tungsten electrodes.Accordingly, the two types of furnace are similar as to both three phase and stabilized operation, but otherwise they differ in several respects, ranging from indirect versus direct-arcing to principal intended application and current state of practical development. Between them they raise questions: (I) of their present or fore seeable economics in comparison with existing processes they are intended to replace , (see Heinke and Neuschutz, 1986, for a review of the merit s of AC and DC plasma-torch furnaces); and (2) of the state of development and accessibility of their plasma theory-in-common."

Jan 1, 1991

By J. H. Nantel, J. F. Archibald

"The presence of radon from uranium-bearing ores, waste and from backfill material introduced underground to provide ground support, work platform and waste disposal functions, requires that ventilation controls be established to maintain safe working level concentrations. One approach has been developed at Queen&apos;s University to quantify radon and radon daughter source level s and to estimate ventilation requirements necessary to maintain these safe levels.Knowledge concerning the sources of radioactive contaminants and their production quantities is of value for planning and design stages of ventilation control systems. For any given mine layout, radiation level estimates may be forecast and modified by ventilation network design where excessive production quantities may exist.Behaviour of Radon Gas in MinesRadon gas, produced from the decay of Ra-226 in a host medium, will diffuse through porous media. In areas adjacent to mine workings, radon will be liberated into the mine atmosphere. The rate of radon emanation is proportional to the rate at which radon is produced within the host material (a function of the ore grade of U308) , to the radon concentration gradient in the host pores and to the diffusion properties of the material.The radon source concentration is determined by the rate at which Rn-222 is produced by the decay of Ra-226, and by the emanating coefficient (E), or fraction of the radon which escapes from the source matrix and is free to diffuse through the pore spaces."

Jan 1, 1984

By J. -P. Tshibangu, M. Ramos da Silva, F. Descamps, C. Schroeder, J. -C. Verbrugge

"The mechanical behaviour of rock materials is largely influenced by the stress state and pore pressure; this needs to be considered in many applications, such as petroleum engineering, tunnelling or stability of underground excavations.Conventional triaxial tests (d2 = d 3) are generally used to assess the influence of confining and pore pressure. In this work, those tests are performed on a porous rock named Sorcy limestone, along with more advanced stress paths like triaxial extension (d 2 = d 1) and purely deviatoric tests with independent pore pressure control. Those tests are combined to a true triaxial study on the dry rock in order to investigate the effect of true triaxial stresses and, hence, build three-dimensional limiting envelopes accounting for the influence of pore pressure.Three-dimensional limiting envelopes of dry Sorcy limestone are built in meridian and octahedral planes. The shape of the octahedral sections changes with the mean stress from triangular to hexagonal and then quasi circular. At even higher mean stresses, the evolution continues towards a triangle with apexes oriented in the direction of triaxial extension stress states. In meridian sections, the deviatoric stress first increases with the mean stress. The transition between this deviatoric mechanism and the cap surface occurs at different mean pressures depending on the Lode angle.Terzaghi’s effective stress is found to govern the yield and plastic behaviour of saturated Sorcy limestone. Triaxial tests show that the limiting envelope does not depend on the loading path (conventional compression and purely deviatoric stress paths). In triaxial extension, the brittle-ductile transition is observed for a higher mean pressure than in triaxial compression, as previously found for true triaxial tests on the dry rock.Finally, it is shown that upon appropriate normalisation, the dry and saturated yield envelopes come very close one to each other. This suggests that only the size of the yield envelope changes between dry and saturated state (pore pressure = 5 MPa); its shape does not seem to evolve."

Jan 1, 2015

By Wenbin Zhang, George W. Poling

"Prior or simultaneous addition of ammonium sulphate can, not only enhance the activating effect of hydrosulphide ions on xanthate flotation of malachite but it can also eliminate possible detrimental or depressing effects of excess residual hydrosulphide . Use of relatively inexpensive ammonium sulphate appears to reduce the consumption of the much more expensive sulphidizing agent for optimal flotation recovery INTRODUCTIONOxidized copper minerals float poorly with conventional thiol-type collectors. This is believed to be due to the nonadherent character of the collector coating, which is readily re- moved by particle abrasion. Rosas and Polingr reported emulsion flotation seemed capable of resisting abrasion during the flotation of non-sulphide copper ores. It appears that the most common flotation technique for oxidized copper minerals comprises sulphidization with Na .S and subsequent treatment by sulphydryl collector. The principles of this method are available . Malghan recently reviewed the studies on the role of sodium sulphide in the flotation of oxidized copper, lead and zinc minerals.It is well known that in the sulphidized flotation of malachite, the activation process depends strongly on the concentration of the sulphidizing agent, i.e., insufficient sulphide gives poor recoveries because of inadequate sulphidization; excessive sulphide also causes poor recoveries due to the depressive effect of the residual hydro-sulphide ions in solution. A major difficulty in sulphidization, especially with a varying feed nature, is to establish and maintain the optimum sulphide concentration in solution. In plant practice, vigorous control of sodium sulphide is required and stepwise addition of the reagent is recommended to improve the efficiency of the process. Soto and Laskowskim have found that malachite, depressed by an excess of sulphide ions, can restore its floatability if air or oxygen is introduced to the pulp. They attributed this to the oxidation of the HS - ions on the surface of the mineral. Jones and Woodcockuvi showed that a sulphide ion selective electrode could be used to optimize the conditions (e.g . amount of hydrosulphide, sulphidization time, flotation time) more readily and precisely than existing methods in the flotation of oxidized copper ores."

Jan 1, 1989

By Ajit K. Sinha

"Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentaryhosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3070 to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By Mike Anderson

The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd is in excess of 450 million dollars. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trails where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trails will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work.

May 1, 2003

By G. Simard, D. Boudeville, A. Leclerc, A. Boivin

"The objective of this work is to study the various parameters that affect the overflow clarity of gravity settlers used in the precipitation circuit of alumina hydrate from the Bayer process. A mathematical model incorporating the size distribution of the feed suspension (Multi Size Group model), its diphasic nature (Schiller Naumann model) and the presence of turbulence (Shear Stress Transport model) has been solved numerically using ANSYS-CFX software. Preliminary results indicate that the overflow clarity is mainly controlled by lateral diffusion of fine particles (~20µm) from the exit of the feed well and by their upward transport from the sediment bed interface. Also the turbulence pattern in the settling zone seems to play a significant role in this vertical transportation. The validity of the model has been verified by comparing the measured solid concentrations from a pilot classifier with the calculated ones. This model could provide mineral processing plant operators and designers with a tool to optimize the configuration of classifiers with respect to the overflow clarity.INTRODUCTIONProblemIn the Bayer process, alumina hydrate precipitation from the saturated liquor is initiated in settler by adding crystallization seeds. Most of the precipitated alumina settles to the bottom of the tank while the liquor and the remaining alumina rise to the top, where they are removed at the overflow. Ideally the overflow clarity, which depends on the operational mode of the classifier, should be controlled within targeted limits."

Jan 1, 2016

By X. Cao, X. -G. Chen, K. Liu

As is well known, the standard Al-Cu 206 cast alloys have extremely low iron contents, usually less than 0.15 wt. %. Recently it is found that the iron contents of the 206 cast alloys can be extended up to 0.5 wt. % through the precise control of the iron-rich intermetallic phases. In the present work, the tensile fracture surfaces of the 206 cast alloys with various iron contents are systematically analyzed to understand the failure mechanisms. Results show that higher iron contents can reduce the tensile properties (especially the ductility) of the alloys mainly due to the increasing volume percent and size of the iron-rich intermetallics. Tensile failure mainly occurs at the iron-rich intermetallics/matrix interfaces for the platelet ß-Fe, but by the self-disassociation for the Chinese script a-Fe and Alm(FeMn). Cracking is easier to initiate and propagate along the longitudinal axis of the platelet intermetallics, but it can be deflected along the branches/arms of the Chinese script iron-rich phases, making the alloy more resistant to the propagation of the cracks, and thus the Chinese script iron-rich intermetallics are less harmful than platelet ß-Fe. In addition, it was also found that the Chinese script a-Fe has even a less damaging effect compared to the Chinese script Alm(FeMn) due to the relatively small size and compact morphology.

Jan 1, 2014

By Jessica Hurst, Mark Holdsworth, Jeff McKay

"In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart. INTRODUCTIONRio Tinto’s Kennecott Copperton Concentrator produces copper, molybdenum, gold and silver. The mill has 4 SAG mills (SAG 1-3, 34 foot diameter and SAG 4 36 foot diameter), 8 ball mills and copper and molybdenum flotation plants, as seen in Figure 1. The 2010 average data is shown in Table 1.In 2002, a Metso Cisa OCS Expert Control system was installed at Copperton for SAG and Ball mill advanced control. The expert control was first placed on SAG 2; data from the first few weeks compared with operator performance indicated approximately an 11 percent increase in throughput. After full commissioning, the system was gradually refined further by plant personnel to develop key performance indices based on SAG feed size, refinement of the sound setpoint for control of mill speed and throughput, specific rules to help the adjustment of speed based on loss of a feeder, etc. With the addition of the pebble crushing circuit, the expert control began utilizing a model estimation of crushed pebble bin level to help stabilize the impact of returned crushed and uncrushed pebbles on the SAG mills. As the ore and limitations change, it is necessary to evolve the SAG logic to better handle any constraints."

Jan 1, 2012

By Andrew Hickinbotham

"A water well represents not only a significant investment but also is a key to making a living or sustaining a reasonable lifestyle. This naturally makes the water well a precious possession that needsto be protected.This paper describes the challenges that TransAlta Utilities Corporation faced and how it responded to the concern of residents that open pit coal mining would affect their water well supplies.BackgroundWells have a certain mystique. Tum on the silver tap and water flows at your command without you knowing how it got there and whether it will continue to flow.Each well is different and has a story to tell. Some wells have a lot of history and are described fondly and with pride (""Grandad built this place 50 years ago and she hasn&apos;t failed us yet""). Some are passed on from father to son, some are part of the pride of good farming, some wells are famous for tapping that huge underground stream or have been mysteriously witched or have been part of a rip-off by an unscrupulous well driller. Some have to be babied so that the cows can be watered, the children can have showers and the dishes can be done. All wells represent a significant $5,000 to $10,000 investment and is a key to making a living or sustaining a reasonable lifestyle.Most wells continue to provide water faithfully - until there is a problem. For those people living next to a mine, there is the additional concern that mining has or will affect their water well supplies. Water well problems reported to the mining company have to be dealt with promptly and responsibly. The mining company&apos;s groundwater specialist must gain the trust and confidence of well owners living in the area ."

Jan 1, 1992

By R. Mariano

"The ability to optimise a concentrator from mill feed to final products requires a process simulator that integrates comminution, classification and separation stages. A key part of any such integrated process simulator is the inclusion of a model of mineral liberation in comminution to predict the particle composition distribution of the comminution products. This need was recognised by Gaudin (1939) who proposed a model of liberation based on the cubic fracture of a mineral texture composed of cubic grains of two minerals.This paper describes the development of a texture-based model of mineral liberation that builds on the method proposed by Gaudin. The approach described here, termed the JK-Gaudin Random Liberation model (JK-GRLM) uses as its basis the measured, volumetric mineral texture data that can be quantified for a given ore using X-ray micro-tomography. The textural data required as inputs for the JK-GRLM include the mineral grain size distribution. While the Gaudin model (in common with other existing liberation models) is a two-mineral (or two-phase) system, the JK-GRLM extends the approach to multimineral systems of up to 15 individual minerals, making it more widely applicable.An example of the application of the JK-GRLM to a base metal sulphide ore is provided. In the example the JK-GRLM is used to simulate the breakage of the measured ore texture and the particle composition distributions of the simulated progeny particles are compared to the measured particle composition distributions of ore that has been physically broken.The ability to calibrate this mineral liberation model with measured ore texture will allow it to be applied in greenfield situations where geometallurgical programs measure texture and in brownfield applications as a key part of integrated process simulations. The development of this model enhances our ability to simulate mineral processing operations as an integrated system."

Jan 1, 2016

By H. Utsunomiya, Mehdi Sanjari, Abu Kabir, Steve Yue, Jing Su, L. Kestens, In-ho Jung

The microstructure and texture evolution of low temperature rolled AZ31 magnesium alloy during annealing were investigated. The specimens were rolled at the temperature of 100? at a high rolling speed of 1000m/min with a reduction of 30% in one pass. Annealing was conducted at various temperatures ranging from 200? to 500? for different time. To study the effect of fast speed rolling, the same annealing procedures have been applied for the specimens rolled at a significantly lower speed of 15m/min. The microstructure was characterized by optical microscopy and scanning electron microscopy, while the texture was analyzed by X-ray diffraction analysis and electron backscattered diffraction analysis. Texture weakening occurred during annealing at both fast and slow rolling speeds. However, at the same annealing condition, fast rolled specimens always had weaker intensity of basal texture than slow rolled ones.

Jan 1, 2014

By Jaroslaw W. Drelich

Despite the success of DLVO and extended-DLVO models that have been developed for homogeneous and smooth surfaces, a vast majority of practical surfaces encountered in mineral ore beneficiation are typically rough at various scales; they are also typically heterogeneous. The interactions of gas bubbles with particles having rough and heterogeneous surfaces are much more complex than the commonly used DLVO or extended-DLVO models predict. The effects of surface roughness on flotation and colloidal interactions have been reported many times in the past, although a clear understanding of their origins has been lacking. To explain differences in colloidal interactions for spherical hydrophobic particles, a theoretical analysis of the interaction potential was carried out for a model rough particle interacting with a bubble surface in an electrolyte solution in this study. The attractive hydrophobic interaction potential was added to repulsive retarded van der Waals and repulsive electrical double layer interaction potentials. The rough microscopic particles were modeled as spheres decorated with nano-sized asperities. Parameters that reflect common flotation separation systems were selected for testing this theoretical model and computation of the energy barrier applicable to particle – flat bubble surface interactions. It was found that hydrophobic asperities with the height of only several nanometers can reduce the repulsive interaction energy by an order of magnitude. Theoretical analysis also reveals that surface coverage of microscopic particles by nano-sized asperities is important as well. The findings of this research suggest that manipulating and engineering the particle surface topography could lead to better control over flotation separation.

Jan 1, 2016

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Ahmed Mohamed Elmahdy, Hidekazu Matsuoka, Kyushu University, Tsuyoshi Hirajima

"Selective flotation of chalcopyrite and molybdenite was studied using various surface treatment methods such as electrolysis, ozone treatment, and plasma. Oxidation via electrolysis method indicated that only chalcopyrite surface is affected by electrolysis due to conductivity difference with molybdenite. Oxidation treatments and XPS analyses indicated that chalcopyrite became hydrophilic due to deposition of oxidized iron on its surface. Various oxidizing methods also showed that chalcopyrite was selectively oxidized and this can apply selective flotation of chalcopyrite and molybdenite. The possible mechanisms are proposed in this work based on surface analyses and thermodynamic calculations.INTRODUCTIONCopper sulphide minerals often associate molybdenite (MoS2) which is one of the most important by-products (Wills, 2006). It is important to recover molybdenite perfectly not only since molybdenite is valuable mineral, but also contamination of molybdenite into copper concentrate or contamination of copper mineral into molybdenite concentrate indicates penalty for both concentrate values (Wills, 2006). Conventional separation of copper sulphide and molybdenite has been achieved with sulphide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulphide. However, this current process shows imperfect molybdenite recovery and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant. Hirajima et al., (2014) have been studied selective flotation of molybdenite and chalcopyrite (CuFeS2), which is the most important copper mineral, with plasma pre-treatment. They reported that plasma pre-treatment process followed by washing treatment can improve molybdenite floatability and depress chalcopyrite. This result is attributed to surface oxidation and selective conversion of chalcopyrite and molybdenite wettability. It may be hypothesized that another surface oxidation methods could give a similar result as plasma treatment process. To test this hypothesis, in this study, as comprehensive study of oxidation effect, various oxidation methods such as electrolysis, ozone, and plasma were investigated. Electrochemical measurements, thermodynamic calculations to predict the chemical reactions happened during the process, various surface analyses, and flotation experiments were carried out."

Jan 1, 2016