Search Documents

By Ferri P. Hassani, Riadh Bouzaïene

"Selected methods of pressure loss predictions in horizontal slurry flow in pipelines are presented. For a given combination of flow velocity, solids concentration and particle size, the slurry and its flow conditions are described, and an appropriate method of pressure loss prediction is outlined. The wide range of conditions treated in this paper may be found in practice in areas varying from the hydraulic transport of low concentration slurries to dense-phase conveying of paste backfill in underground mines.IntroductionThe hydraulic conveying of solid particles in pipelines is a major component of the mining and mineral processing industry. Whether the objective is to transport ore to the processing plant or to make use of mill tailing as backfill material; the need for well designed, economical hydraulic conveying systems is recognized.The contribution of this paper is part of an on-going research program at McGill University involved in optimizing and developing techniques for total mine waste disposal. One of the main concerns in the conveying of solid-liquid mixtures is the prior knowledge of the pumping power input required. This energy requirement is directly proportional to the pressure losses incurred in the pipeline system. Understanding the sources of such pressure losses and predicting their magnitudes should enable the system designer to make informed decisions regarding the optimum mode of hydraulic transportation commensurate with the over-all requirements of the operation.This paper is an attempt to classify pressure loss prediction methods encountered in the literature for solid-liquid mixtures. In spite of the large number of publications spanning thirty years of research in the field of slurry transportation, it is sometimes difficult to correctly identify the appropriate methods applicable to a given situation. This is partly due to the inherent complexity of the mechanics of slurry flow and the ensuing uncertainty about the nature of the flow regime under investigation.Our approach is to use three fundamental parameters, namely: flow velocity, solids concentration and particle size (for solid particles with a given density) to characterize the slurry and the flow conditions, and to match them with an adequate pressure loss prediction method. For each combination of flow velocity, solids concentration and particle size, a description of the most likely prevalent flow conditions and some known methods of dealing with them will be presented. Qualitative definitions of ""high"" and ""low"" magnitudes of the aforementioned parameters will be given as a general guide to the classification scheme presented in this paper."

Jan 1, 1992

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By L. C. Bird, A. I. A. Salama, M. W. Mikhail

"A program of sampling in Canadian washeries was carried out by the Coal Research Laboratory (CRL) over a period of two years to evaluate the performance of various density separators in these operations(1). Operating data on quality and recovery of products, separation efficiencies and cutpoints for each separator type are compared with data predicted using computer models developed from previously existing data.The Heavy Medium Cyclone (HMC), Heavy Medium Bath (HMB) and jig models give predictions of recoveries and qualities of products for sizes coarser than 10mm with absolute value of error mean less than 7 per cent, whereas predictions of the Water Only Cyclone (WOC) model for -10mmfine coal are with absolute value of error mean less than 8 per cent. Although less accurate for -10 mm fine coal, the HMC and jig models produce predictions of recoveries with absolute value of error mean less than 2 per cent and quality of products predictions with absolute value of error mean less than 28per cent which are generally acceptable because more liberation in the fine fractions appears to compensate for any difference in the accuracy of separation, resulting in good prediction of the clean product. However, ash content of the actual fine refuse was lower than predicted. The difference is attributed to the highly friable nature of Canadian coals which tends to cause an excessive loss of coal fines to the fine refuse.A comparison study based on quality and recovery of products is made between the Dutch State Mines (DSM) models and the recently modified models, both produced comparable predictions."

Jan 1, 1985

By M. A. T. Cocquerel, J. G. Eacott

"Simulation techniques may be used to optimize existing processes and plant operations, and in plant design at the engineering study stage of a project . This paper describes the latter application, using a computer, to optimize the concentrate stockpile requirements of a modern copper smelter.A large open-pit mining operation is envisaged and it is assumed that copper concentrate is smelted in two flash furnaces. The proposed mining plan gives rise to metaffurgical considerations in smelting which dictate that concentrate blending is carried out in the early years of operation in order to eliminate wide variations in the grade of concentrate charged to the furnaces . Stockpiling facilities are therefore necessary for blending purposes and also to provide a strategic reserve of concentrate to ensure continuity of concentrator and smelting operations.The objective of the study is to determine the optimum size of concentrate stockpile required to take account of both metaffurgical and strategic considerations. Two separate simulation models are developed to achieve this objective. The first model is used to determine the minimum size of stockpile necessary for blending purposes to smooth out variations in concentrate grade between 15 - 60% Cu, with associated 34 6% Fe, respectively, and ensure that the concentrate fed to the furnaces does not faff below 12% Fe, which is considered a minimum for good smeltability.The second simulation model covers a projected three-year operating period and indicates the maximum size of stockpile which is likely to develop during scheduled and unscheduled shutdown periods in the concentrator and smelter.Covered storage volume and conveying facilities for the optimum size of concentrate stockpile can be designed based on the results generated by the simulation models."

Jan 1, 1980

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

By P. MacPhail, G. S. Dobby, I. M. Flint

"The objective of the laboratory work described in this paper has been to develop a method f or producing small gas bubbles at moderate to high gas rates in a flotation column. Small bubbles are particularly important for attaining reasonable flotation rates of fine particles. An ultrasonic aerosol generator has been employed to add frother solution directly to the gas stream. Using porous glass and filter cloth spargers, aerosol frother addition has produced bubbles at 1/2 to 2/3 the diameter of those produced by conventional frother addition to the liquid, at a lower frother consumption.IntroductionGas bubbles are generated in a flotation column most commonly by forcing gas through a porous medium called a sparger. Typical sparger material includes rubber (pierced with small holes) , fabric (such as filter cloth), fritted glass, or porous metal (steel or bronze) . Solid sparger material is suitable for laboratory use; however, for industrial applications a flexible sparger such as rubber or fabric is necessary to prevent the eventual plugging of orfices with solid particles and/ or precipitates. An exception to this is the use of a gas liquid contactor external to the column in combination with pressure release of gas in water, a method that has been demonstrated to produce very small gas bubbles. The typical objective of bubble generation for flotation column purposes is to produce bubbles with diameter of about 0.1 cm (and less) at a gas superficial velocity of 1 cm/s to 3 cm/s. In general, the smaller the bubble, the better. In man y cases, though, there is little , or nothing, gained by generating bubbles less than about 0.05 ern in diameter.Several factors affect bubble size when generated by a sparger: gas rate, orifice diameter, sparger surface area, surfactant type, surfactant dosage, and static head. At very low gas rates bubble diameter is independent of flow rate and is proportional to orifice diameter. At the moderate gas rates encountered in flotation columns bubble diameter, db' is related to gas flow by: db oc vg n, where vg is superficial gas velocity (rate of gas flow per unit column area). For porous steel and filter cloth, n has a value of about 0.25 for vg between 0.2 cm/s and 2 cm/s(2). The magnitude of the effect of orifice diameter at these gas rates is unclear. The effects of frother type and concentration on bubble size issuing from a single orifice have been measur ed by Miagkovaru , shown here in Figure I(IS). The reduction in bubble diameter upon surfactant addition is due to the lowering of interfacial tension created by adsorption of surfactant at the gas liquid interface."

Jan 1, 1988

By E. M. De Souza, A. M. Coode

"Since potash was discovered substantial rock mechanics research has been done to develop the technology needed to cope with the unique conditions in Saskatchewan mines, to assure general mine safety and to assess the problems associated with mining potash at depth.The practical result of this research was the development of multiple entry systems incorporating yielding pillars for access ways and the chevron type layouts for production panels. These developments proved the viability of extracting potash from between 950 m and 1100 m depth using a high degree of mechanization. High extraction ratios could not, however, be achieved using the developed technology.The presence of a competent salt back is critical to mining the potash, and underground practice is governed by the presence of anomalous geological zones. These factors may be associated with the occurrence of brine inflows. One potash mine in Saskatchewan ceased its underground operations and was closed due to flooding of the entire mine. Two other potash mines in Saskatchewan had significant brine inflows. The costs involved in brine pumping, equipment relocation, bulkhead construction, grouting, and in auxiliary operations can run into the tens of millions of dollars.At Central Canada Potash, the use of stress relief and yielding pillars in the design of the mining layouts has resulted in over-all stable underground excavations and safe mining practices. There are two types of production room s, the chevron and the hybrid, which result in a planned block average extraction ratio of 35010. Mining activity has resulted in brine ingresses in two areas, and additional operating costs have been incurred over the years. These mining areas have demonstrated abnormally high closure rates, and rapid back deterioration. A program was established in those two areas to ensure the practice of safe mining procedures.The short-term perspectives inherent in the program included the elimination of all uncertainties associated with the possibility of an increase in brine inflow leading to flooding, the elimination of the abnormal ground behaviour and ground deterioration in the inflow areas, and the reduction of the long-term adverse effects of mining on regional mine stability. The program was also designed to provide means for developing alternative safe mine layouts which would improve the exploitation of potash resources. Details of the extensive work performed during the program are found elsewhere (E. De Souza, 1988).Grouting and salt backfilling are viable techniques to control brine inflows in underground excavations in potash mines. Detailed instrumentation of the backfilled test areas provides information on the long-term behaviour and effectiveness of the grout/backfill system, allowing for rational decisions on the complete abandonment of these mined out areas, thus resulting in considerable operational cost savings.This paper is presented in two parts: the first addressed the problems of diamond drilling , grouting and backfilling in Panel 209 and the second, addresses the problems of instrumentation and rock mechanics."

Jan 1, 1990

By M. H. Moys, J. A. Engelbrecht

"Large-diameter flotation columns are subject to severe axial mixing which has reduced column recovery and has generally limited it to cleaner applications. It has been assumed that columns with diameter greater than 1 m should be baffled to reduce axial mixing, but little work has been reported quantifying the effectiveness of baffling. Tests were done on a 0.2 m by 2 m column fitted with baffles of different geometry. It was generally found that the inclusion of baffles in the column worsened rather than improved mixing conditions in the column. This is explained in terms of a model for the effect of poor gas distribution on the behaviour of the column; this showed that under typical conditions a 16% excess of gas flux in the one compartment of a two-compartment column could result in one of the compartments being ""dead"" (i.e. with no net flow of slurry through it), resulting in a substantial loss of performance. The quality of mixing in the laboratory column was only reliably improved when the baffle was raised so that its top was positioned above the froth-slurry interface level. It should be possible to increase column recovery substantially with this configuration. The improved residence time distribution also means that columns can be used more effectively in roughing and scavenging applications. IntroductionFlotation columns have generally been used in cleaner applications, starting with their dramatic success at Mines Gaspe(1). Their lack of applications as roughers and scavengers is probably due to their poor residence time distribution (RID) when compared to the conventional cells they would replace. Espinosa-Gomez et al,(2) recently used them in rougher applications but installed three columns in series, presumably to cope with this disadvantage.Dobby and Finch in their seminal papersl(3,4) on the scale-up of flotation columns were the first to quantify the impact of axial mixing on the performance of industrial flotation columns. Laplante et al.(5) collected further data from the literature for column diameter D, ranging between 5 cm and 183 cm, gas superficial velocity Jg ranging between 0.7 cm/s and 2.8 cm/s and per cent solids in the feed S ranging between 3% and 52%. These data were analyzed with reference to the axial mixing model using the boundary conditions for closed vessels (the latter are more appropriate for flotation columns but the model is more difficult to use because analytical solutions for the RID are not available). The data were correlated by:"

Jan 1, 1993

By R. D. Clark, Heinz Althoff

"The advantages and disadvantages of a mobile crushing plant with a belt conveyor system compared to a stationary crushing plant with haulage by heavy trucks are described. The capital expenditure and operational expenses are compared and the individual cost factors are explained.Every open-pit mine or quarry, however, is different and has to be assessed and analyzed individually in order to find the optimum and most economical solution. Due to the high truck haulage costs, many open-pit mines tend to the more economical solution with mobile crushing plants and continuous belt conveyor operation. IntroductionFor the material haulage within an open-pit mine the heavy truck is the most flexible means of transportation. However, due to the high fuel consumption, wear and labour costs, it is also the most expensive one. Therefore, many open-pit mines are looking for alternative solutions for the material transport A mobile belt conveyor system is most likely to meet the requirements because it is efficient and economical with regard to the power consumption. The material , however, has to be crushed at the mining face to lumps which are suitable for conveyor operation. For this purpose a mobile crushing plant is required.In some open-pit mines the crusher is also used to crush the material to lumps of smaller particle sizes in order to save crushing costs in the preparation plant.Although a cost comparison between a system with stationary crusher and truck haulage and a system with mobile crusher and belt conveyors favours in most cases the belt conveyor system, up till now only a few open-pit mines and quarries benefit world-wide from the advantages of the mobile crushing plant with continuous belt conveyor operation."

Jan 1, 1986

By R. Kamguem

The surface of a mechanical part plays an important role in determining performance in service. The presence of scratches left by the cutting or tearing of the material on the surface of the workpiece supports the concentration of stress and strain. This article presents the experimental study for high speed milling of the aluminum alloy 7075-T6, using cutting tools different by the nose radius and coatings (TiCN, TiAIN, TiCN + A12O3 + TiN). A multi levels factorial design of experiment (DOE) and statistical analysis was used. The roughness parameters investigated are Ra, Ra, Rv, Rc, Rsm, and Rk. The results show that the feed rate, the types of coatings and the geometry of the cutting tools have the most significant impact on the surface roughness profil. Surface finish charts according to feeds and cutting speeds were established for each tool tested.

Jan 1, 2011

By N. Dahata

B206 aluminum?copper alloy has a potential for wider use in the automotive industry due to its light weight and relatively superior mechanical properties as compared to aluminum-silicon alloys. The possibility of casting this alloy via Lost Foam Casting (LFC) has not been investigated in detail. Therefore, the effects of foam types (T170B standard untreated EPS and T175-brominated EPS), coating types (Styro Shield 5553 and Styro Shield 5554), copper level (4.5 wt % and 5.0 wt %) and titanium levels (0.5 wt % and 0.25 wt %) were related to fillability, microstructure and microporosity. The metal velocity in T175 EPS pattern was higher than that in T170B EPS pattern. For T175 EPS pattern, the total solidification time was 3% higher and the loss of temperature for decomposition of EPS was lower than those in the case of T170B EPS pattern. The grain size, porosity level and maximum pore size were quantified using Light Optical Microscopy (LOM) and image analysis. The casting with T175 EPS pattern showed larger grain size relative to that with T170B EPS pattern. The porosity level and the maximum pore size decreased significantly when the titanium level was increased from 0.05 wt % to 0.25 wt %.

Jan 1, 2007

By Robert M. Hopkins, Craig C. Monahan

A corrosion survey was performed on ten selected H-piles which support a reinforced concrete wharf located at Trepassey, Newfoundland. Approximately 900 thickness measurements were taken at twelve different locations in each off our zones on the steel piles: the splash (atmospheric) zone, the intertidal zone, the low tide zone and the submerged zone. Results show that over the 2o-year life of the wharf, corrosion has been most severe in the splash, low tide and submerged zones with average corrosion rates for the flanges of 6.95, 9.45 and 6.86 mils per year (mpy}, respectively, and average corrosion rates for the webs of 5.13, 4.12 and 3.45 mpy, respectively. Minimal attack was found in the intertidal zone where the average corrosion rate was only 1.66 mpy on the flanges and 1.37 mpy on the webs. Such a pattern of attack is frequently observed f or steel piles partly submerged in seawater. The abnormally low corrosion rate associated with the intertidal zone is generally explained as being due to cathodic protection induced by the high corrosion rate in the adjacent low tide zone. Analysis of the corrosion data obtained for the Trepassey wharf would suggest that this explanation might be incorrect. An alternate hypothesis has been brought forward which better accounts for the extremely low corrosion rate observed in the intertidal zones of these piles.

Jan 1, 1990

By Graham Popplewell

"Modular, predesigned diamond recovery plants have been a feature of the diamond mining industry for more than 20 years. The reasons for the selection of such a design route are contrasted with the alternative option of custom-designed route and the relative merits of the two approaches are discussed. The predesigned, modular plant is shown to be particularly applicable for the smaller operation, whether as part of a diverse alluvial mine, an auditing facility for an adjacent large plant, bulk sampling or a remote installation such as is envisaged in the Canadian diamond industry. The characteristics of the predesigned modular plant are described, as well as the inevitable compromises resulting from the concept. IntroductionThis paper explores the application of predesigned modular plants to the diamond mining industry and contrasts their features with the custom-designed installation .A predesigned modular plant is a self-contained unit, or a number of self-contained units, which, when assembled , make up a treatment facility. This is usually small scale in treatment capacity, although multiple modules may be used to increase over-all throughput.A move toward the use of such plants in the diamond mining industry resulted from the relatively unsophisticated nature of the design , the proven nature of pretested , standard plants and the low cost per tonne of capacity and their specific application in remote locations.The recovery of heavy minerals by dense medium separation (DMS) is intrinsically safe and more efficient than the older methods, such as jigs and rotary pans.All diamond recovery plants feature three distinct sections:• feed preparation• gravity separation, and• final recovery."

Jan 1, 1992

By P. O. Rag, Daniel E. Walsh

"Gravity concentrators are evaluated either in closed or open circuit. The process developed by MIRL employs the use of neutron activated gold (/98Au) and radiation detection circuits which monitor the concentrator's product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. In addition to allowing for a more accurate and detailed recovery analysis, this process significantly reduces the time and cost required for unit evaluation when compared to other gold recovery analysis procedures. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems.IntroductionThe surge in gold prices of the late 1970s and early 1980s was followed closely by a renewed interest in gravity concentration processes, especially in concentrators claiming efficient recovery of fine placer gold. Cones, spirals, spinning bowls, jigs and cyclones are all considered potential fine gold concentrators. Fine gold, in this context, is defined as not only that gold finer than 250 um (60 mesh""), but also coarser gold, whose low shape factor may decrease its recovery by conventional, large-scale sluicing operations.Adoption of fine gold concentrators by the Alaskan placer milling industry was retarded by the lack of reliable, accurate, and reproducible data on concentrator efficiency with respect to fine placer gold recovery. In most cases, concentrator performance was based on a limited number of tests run on placer material, about which only slight knowledge of gold size and shape characteristics existed. In order to be prepared for the resurgence of interest in fine gold concentrators, which will follow the next upturn in gold prices, a detailed study of the fine gold recovery characteristics of gravity concentrators needs to be conducted."

Jan 1, 1986

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By L. A. Wolff

"Second only to profitability (but not always), productivity is the most sought after measurement for any operation. Whether it is in mining, manufacturing, construction, etc. managers always strive to know how productive various plants are. Even the Federal Government publishes, on a monthly basis, the nation's factory productivity.Just what is productivity and how is it measured? This is an important topic that needs definition. There could be as many definitions as there are people who use it. In the mining industry, the problems of defining productivity would be analogous to the definition of equipment availability. Each mine uses its own definition to suit its needs. Webster's Dictionary primary definition for productivity is ""the quality or state of being productive,"" with productive defined as ""yielding or furnishing results"". This is a definition open to a broad spectrum of interpretation. A discussion of how productivity is currently used in the mining industry and an introduction to a potentially different approach to its measurement and meaning is outlined in this paper.Defining ProductivityTypically, mining companies track several productivity measurements. These are partial measurements and can include the following: tons per specific equipment class per hour, tons per man-hour, and tons per shift. None of these, however, track the over -all performance of an operation, that is, a unit of output per unit of input.For a mining operation, output can be defined as the ore for mill processing. Input includes the required components of production to get to the first step of processing.The Wesbter's Dictionary definition exposes a major fault with the popular conception of productivity. The critical issue of accountability is not addressed. Anyone can produce, but how effectively and efficiently are resources used? Quantifying an inclusive measurement is difficult. Statistics referring to an increase in productivity are often published. For example, the statement, ""gold productivity has increased by 10%"" has many potentially dangerous interpretations. One must ask, what does this statistic really mean? Did gold companies produce 10%” more gold? Were less manpower or equipment required to produce an equivalent amount of gold? Did ore grades increase resulting in more ounces of gold produced, etc. Obviously, production and productivity can have similar implied applications and meanings, but also two different, distinct meanings.To mitigate a problem like this, a standard needs to be developed within the mining industry. Because of varying ore grade, changing waste to ore ratios, different mining methods, etc. all of which have a direct impact on mining, development of a standard is difficult. Kendrick(1) discusses the use of Total Factor Productivity as a productivity measurement. Summarized, the total factor productivity measure is an indication of the change in efficiency in the use of basic labour and capital factors associated with an operation.This measurement has little meaning when calculated at a given point in time. It should be an on-going calculation, tracking an operation over a period of time, to evaluate trends. These trends can be used to determine if an operation's productivity is what it should be, and alert management to potential problems before they become major and adversely affect an operation."

Jan 1, 1990

By T. G. Joseph, R. K. Soni, M. Curley

"Rapid dampening suspension is a proposed suspension design for ultra-class haulers that is intended to avoid metal-to-metal contact inside a strut and under shock loading, thus improving ride quality and ameliorating fatigue loading issues on a hauler structure. Laboratory testing has shown the ability of the proposed design to reduce the opportunity for bottoming out, that is, metal-to-metal contact between the colliding ends of oleo-pneumatic, two-piece suspension struts during the compression cycle. This paper predicts the performance of a full-size rapid dampening suspension strut by applying scaling rules to test the proposed design based on a set of field data from a Caterpillar 797B ultra-class haul truck operating in the oil sands region of the province of Alberta, Canada. The predicted performance of the suspension strut is compared to that of the original equipment manufacturer model, which was monitored on board the truck during field data collection. ¦ KEYWORDS Haul truck, Original equipment manufacturer (OEM), Rapid dampening, Strut, Suspension RÉSUMÉ La suspension à amortissement rapide est une conception de suspension proposée pour des camions de transport de catégorie ultra-class (des engins dont la charge utile dépasse les 320 tonnes métriques), visant à empêcher un contact métal sur métal à l’intérieur d’une jambe de suspension et dans des conditions de choc au chargement. Elle améliore la qualité du roulement et les problèmes de charge de fatigue sur la structure d’un camion de transport. Les essais en laboratoire ont confirmé que la concep¬tion proposée évitera au cylindre interne de heurter le cylindre externe, autrement dit empêchera le contact métal sur métal des jambes de suspension oléopneumatique en deux parties pendant le cycle de compres¬sion. Cet article prévoit la performance d’une jambe de suspension à amortissement rapide à taille réelle en appliquant les lois d’échelle afin de mettre à l’essai la conception proposée, sur la base d’une série de données de terrain relatives à un camion de transport 797B de catégorie ultra-class de Caterpillar (aujourd’hui remplacé par le nouveau modèle 797F) utilisé dans la région des sables bitumineux de la pro¬vince de l’Alberta, Canada. On compare la performance prévue de la jambe de suspension à celle du modèle du fabricant d’équipement d’origine (FEO), qui a été contrôlée à bord du tombereau pendant la collecte des données de terrain. ¦ MOTS CLÉS amortissement rapide, camion de transport, fabricant d’équipement d’origine (FEO), jambe de suspension, suspensionINTRODUCTION Research basis for the paper This paper is based on the unpublished MSc thesis work of El-Sayed (2003), Santos (2007), and Soni (2009) under the direction of Dr. Tim Joseph within the oil sands–equipment interactions program (OsEIP). OsEIP is part of the Alberta equipment–ground interactions syndicate (AEGIS) surface mining research group, School of Mining and Petroleum Engineering, University of Alberta. The aforementioned work spanned a decade of progressive studies into rapid dampening suspension systems, leading to the scale performance indications highlighted here. Although this paper uses a specific Caterpillar 797B suspension strut for field monitoring and as a basis for scale prediction of a modified rapid dampening suspension strut design, the design scaling principles used here could be applicable to any such design change consideration for an oleo-pneumatic suspension system."

Jan 1, 2019

By Georges Houlachi, Raynald Labrecque, Jean-Noël Cloutier

"Electrodialysis (ED) is an electro-membrane technology based on electrochemical process using electrical energy for the production of chemicals. The process can be used for concentrating, extracting, separating products, modifying molecules, purifying solutions, pH adjustment and regenerating salts into their base and acid. This paper reviews the principle of ED, present some of the different options and discuss applications that are relevant to the hydrometallurgy and mining industries for the treatment of effluents focusing on recovery of chemicals (acid and metals) and recycling of water minimizing the environmental footprint.INTRODUCTIONElectrodialysis (ED) is usually defined as an electrochemical separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution and other uncharged components [1]. ED technology consists of an electro-membrane technology based on an electrochemical process using electrical energy for the production of chemicals. It is a method combining electrolysis and dialysis was proposed for the first time in 1890 by Maigrot and Sabates [2]. In the late 1930s Teorell, Meyer and Sievers discussed membrane phenomena, revealed membrane potential, electric conductivity, transport number [3]. Meyers and Strauss introduced a multi-compartment ED apparatus consisting of two electrodes and a stack of ion-exchange membranes between them [1]. They succeeded to double the concentration of a KCL solution [3- Tarleton]. In general, ED consumes less energy than electrolysis to perform salt splitting. In that regard, one can expect an energy reduction of about 30% [4–5]. ED offers a great versatility in the domain of separation processes. Indeed, it can be used for concentrating, extracting, separating products, purifying by desalination, pH adjustment and regenerating a salt to acid and base components. This paper reviews the principle of ED, presents various options available and discusses potential applications relevant to the mining and metallurgy industries with economics of some successful industrial applications."

Jan 1, 2016

By M. R. Henzinger, G. Lenz, A. Gaich, Pötsch, W. Schubert, P. Wagner

"The better the information on the rock mass and its fracture system, the better is the basis for any rock mechanical decision that is required during the excavation process. While in conventional tunnelling free view to the tunnel face is available, possibilities are limited for mechanised tunnelling using a tunnel boring machine (TBM). An approach, already formulated in 2005, is used that produces digital photographs through openings in the cutting wheel of a TBM and merges them into a circular three-dimensional image. The 3D image is then used for geometric rock mass characterisation purposes including geological mapping, for example to measure spatial orientations or determine joint spacing. In the paper the basic concept is described together with first results from a pilot test.INTRODUCTIONA three-dimensional image unites digital photographs with spatial information on the objects/surfaces it shows. Since they combine geometric and visual information they are a straightforward source for geometric rock mass analysis and geological mapping. Their obvious benefits among others are: (i) they allow spatial measurements even in inaccessible regions, (ii) they provide objective and reproducible records of the rock mass conditions, and (iii) they increase working safety (Gaich et al. 2004).Pre-requisite for the generation of 3D images is the acquisition of at least two photographs from the region of interest. From the photographs the imaged object surfaces are reconstructed by means of image analysis using methods from photogrammetry (Slama, 1980) and computer vision (Hartley & Zisserman, 2001). See also Figure 1."

Jan 1, 2015

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982