Search Documents

By S. J. van Rensburg

Competition for resources, including water and arable land, refocused attention on water and gold tailings management with respect to quantity and quality. MINTEK established and validated an "Advanced Leach Facility" to record kinetic leach information aimed at gold refractory sulphide ores. This facility was developed because of the need for additional leach process information to enable proactive decision making. Instead of focussing on optimised gold recovery only, the impacts of pre-oxidation methodologies were evaluated by considering key parameters, including cyanide speciation, reagent consumption, thiocyanate, arsenic, heavy metals, salt loads, water quality and residue stability. Results from oxidative leaching of a refractory gold ore employing oxygen, ozone, ultra-fine grinding, high shear and pressure oxidation are discussed. The relative cyanide and lime costs and environmental and sustainability effects associated with these technologies are briefly outlined.

Jan 1, 2011

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016

By P. C. Sui

Numerical investigation and parametric simulations of the coupled electrical conduction and mass diffusion in the GDL of a PEMFC are reported. The coupled transport is solved using a 2D, "under-the-rib" computational domain for the cathode GDL. The current density on the GDL/catalyst layer interface, which constitutes one of the boundary conditions for the GDL domain and reflects the activation overpotential in the catalyst layer and the ohmic loss in the membrane, is solved iteratively using a novel numerical algorithm. A parametric study is performed to investigate the effects on current density distribution of various operating conditions such as oxygen concentration and membrane resistance, and of design factors such as GDL geometry, anisotropic transport properties, and deformation under the land area. The results show that the current density distribution under the land area can be dominated by either electron transport or mass transport, depending on the operating regime.

Jan 1, 2005

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By A. Bendada, P. Servais, X. P. Maldague, C. Ibarra-Castanedo, C. Mohr

Infrared (IR) thermography is a nondestructive, non-contact and non-intrusive technique that allows the fast inspection of large and complex structures with limited accessibility. Pulsed thermography is particularly interesting for the inspection of aerospace materials such as composites given that, after submitting the specimen surface to a thermal front, the most common types of subsurface discontinuities (e.g. porosity, de laminations, dis bonds, fiber breakage and inclusions) can be detected with an IR camera as regions showing abnormal temperature patterns. We present first the case of an aircraft door with water ingress and surface repairs on its honey comb structure. We also highlight the advantages and limitations of thermography for the inspection of aircraft composite parts, such as edge flaps, rotor blades and speed breaks. Finally, we expose some results from a Kevlar® non-planar specimen with Teflon® inclusions at different depths and locations.

Jan 1, 2006

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By I. Silin, M. Stapelmann, H. Wotruba, K. M. Hahn, C. Gerold, J. Katzmarzyk

New deposits are often characterized as low-grade and complex ore bodies. To date, processing of fine grained ore deposits implies complex processing routes with high energy consumption. For that reason, the investigation of dry grinding, e.g. with vertical roller mills (VRM), is an approach to save energy reserves. It is already proven that dry grinding can influence subsequent processing steps. In terms of flotation, the surface characteristics of the minerals are crucial for a successful flotation process, e.g. the sufficient adhesion of mineral particles and air bubbles. Wet grinding results in different surface properties of the product entering the conditioning stage than dry grinding, which has direct influences on the subsequent flotation process. To investigate the consequences for flotation, processing of a copper sulfide ore containing chalcopyrite and bornite was investigated, including grinding and rougher flotation. The effects of wet tumbling mill and dry VRM grinding on the degree of liberation of valuable minerals are characterized using mineral liberation analysis by scanning electron microscopy. The obtained flotation results, as well as the recorded flotation parameters such as dissolved oxygen, oxidation reduction potential and conductivity are presented and discussed. INTRODUCTION Copper production is mainly connected to porphyry copper deposits as main source for copper sulfides such as chalcopyrite and bornite. State-of-the-art processing of these deposits is already established worldwide for decades, combining crushing, fine grinding and subsequent flotation with rougher, cleaner and scavenger stages (del Villar, Desbiens, & Maldonado, Bouchard, 2010). While the demand for copper is increasing, copper grades of the deposits are decreasing and the remaining ore bodies have more complex mineralogy and finer particle size distribution. This implies processing routes with high water and – due to the liberation of fine grained valuable minerals – high energy consumption by fine grinding. One of the main energy consumers in processing plants is the grinding section, which accounts for more than 50% of the energy consumption in processing plants and even 4% of the worldwide energy consumption (Jeswiet, & Szekeres, 2016). Therefore, dry fine grinding alternatives are applied to enhance the overall energy consumption of mineral processing plants: high pressure grinding rolls (HPGR) and vertical roller mills (VRM).

Jan 1, 2019

By S. Avalos, J. M. Ortiz, W. Kracht

Semi-autogenous grinding mills are intensive energy consumers. Current models base their energy consumption inference on operational variables and feeding ore characterization. While they provide adequate design guidelines, they are not suitable for real-time energy forecasting dealing with gaps in operational dataset and up/downstream process bottlenecks. This work explores the capability of Gated Recurrent Units to learn the semi-autogenous grinding mill consumption behaviour. Gated Recurrent Units are trained to forecast different time-support consumptions under a time-series operational dataset. The results show high performance on small supports (30 minutes) to capture local variability and long-trends while larger time supports (8 hours) can only capture time-trends but not local variability. The proposed technique seems promising for further research and implementation on real mine cases since the input variables are low-cost and easy to obtain. INTRODUCTION Current changes in the Chilean energy matrix (Román-Collado, Ordoñez, & Mundaca, 2018), from fossil fuels to renewable energies, have impacted different industries and particularly the mining sector. Solar energy incorporation into greenfield/brownfield projects will help reducing costs and will lead to rethink foundational paradigms (production and processing strategies) (Pamparana et al., 2017). Also, integration of new space-time predicting tools together with automated real-time updating models are some of the main challenges in the geometallurgical framework (Ortiz et al., 2015; van den Boogaart & Tolosana-Delgado, 2018). Those contexts encourage and demand the development of tools capable of predicting the energy consumed by mining systems, being comminution the greatest energy consumer with an average close to 50% of the entire mine consumption (Cochilco, 2013). In comminution, the semi-autogenous grinding mill (SAG) represents the largest energy consumer (~10 nominal each SAG). Theoretical and empirical energy consumption models (Jnr & Morrell, 1995; Morrell, 2004; Silva & Casali, 2015) base their inferences mainly on feed/product size distributions, SAG sizing, bearing pressure, feed hardness, water addition and grinding charge level, and commonly assume steady-state and work isolated from up and downstream processes. While those techniques provide adequate design guidelines, they are not suitable to predict hourly, daily or even weekly energy consumptions on interconnected comminution circuits where upstream/downstream bottlenecks lead SAGs to operate below designed regimes. Forecasting energy consumption is required by short-term energy management, medium and long-term planning energy consumption, designing the nominal capacity of renewable energy sources, among other. Also, when models are input-sensitive and some of those input measurements are expensive and/or time consuming, model robustness suffers when real-time predictions are required.

Jan 1, 2019

By J. T. Birkholzer, M. Rutenberg, K. -H. Lux, R. Wolters, J. Rutqvist, L. Blanco Martin

In this paper, we present numerical results corresponding to the Thermal Simulation for Drift Emplacement (TSDE) test, conducted in the Asse salt mine (Germany) between 1990 and 1999 to simulate reference repository conditions for spent nuclear fuel in rock salt. This test is of significant relevance for nuclear waste disposal in salt because extensive research and measurement programs were set up for the experiment. In our numerical study, we use two sequential simulators, TOUGH-FLAC and FLAC-TOUGH, and we investigate two-way coupled processes, focusing on thermo-mechanical analyses due to the main effect of heating. The two simulators used have recently been updated and are able to deal with large strains and creep processes. Moreover, specific constitutive relationships and coupling functions for rock salt and crushed salt under repository conditions are available. Within the framework of a benchmark exercise between Lawrence Berkeley National Laboratory and Clausthal University of Technology, the same scenario has been modeled in three dimensions using the two simulators mentioned. The main objective of the current, first stage of the benchmark is to evaluate the capabilities of these two simulators to predict relevant processes under repository conditions for high-level nuclear waste in saliniferous media. The comparison of the numerical predictions between them is very satisfactory, leading to a successful code-to-code verification. The comparison between measurements and numerical results shows that the most important processes are captured by the codes and constitutive models used. However, some differences exist between measurements and numerical results. These differences will be addressed in the next stage of the benchmark exercise, in which a parameter fitting effort will be undertaken. Overall, from the results obtained it can be concluded that TOUGH-FLAC and FLAC-TOUGH have the necessary capabilities to reproduce relevant processes under repository conditions for high-level nuclear waste in saliniferous formations.

Jan 1, 2015

By J. Yue

The particle breakage kinetics, product size and size distribution, as well as grinding limit for quartz suspensions in a horizontal stirred mill are investigated. Results of grinding studies on quartz suspensions in a horizontal stirred mill confirm "first-order" particle breakage rates. A comparison of equation fits reveal that the product size distribution from stirred mill is best represented by the Rosin-Rammler equation when compared to the Gaudin-Shuhmann equation, but results fit poorly as particle size below five microns. A method of determining breakage rates versus particle size is demonstrated which shows that the 10% top size fraction is most appropriate for the determination of specific breakage rates. The method is used to demonstrate the relationship between particle breakage rate and particle size. As the feed particle size becomes smaller, the size reduction ratio decreases and approaches a grinding limit which depends on the effective stresses created in the mill.

May 1, 2004

Adaptive Processing as proposed in geometallurgy has to rely on spatially interpolated information on geometallurgical parameters like phase composition, size distributions of particles of different phases, grain shape parameters, and portions of value elements in different grains. Using the geostatistically predicted values for adaptive processing, e.g. for the selection of milling diameters, thresholds in physical separation, or choices on using an extra pre-separation step, is typically not optimal. Mathematically this effect is introduced by two forms of nonlinearities: 1) The nonlinear scales of compositions, distributions, and shapes have special properties with respect to geostatistics. Classical geostatistics creates some artefacts for these nonlinear scales. On the other hand, modern geostatistical procedures adapted to these scales do not provide unbiased results with respect to linear transformations of the data (e.g. biased block estimates). 2) Neither economic nor ecological effects (e.g. monetary gain) of processing decisions are linear in the interpolated geometallurgical parameters. These nonlinear transforms are not unbiasedly estimated by the likewise transformed unbiased geostatistical predictions of the geometallurgical parameters. Furthermore, we need to optimize the conditional expectation of the gain, rather than obtain an unbiased estimate. Standard geostatistics as such does not provide the "right sort" of estimates for adaptive processing. A nonlinear kriging procedure is needed to approximate the nonlinearities mentioned before. We propose to solve these problems simultaneously using a nonlinear geostatistical technique for predicting the target function (the monetary gain), rather than to predict the geometallurgical parameters and compute the gain from them. The optimization can then be performed directly on this estimated function. It can be shown that this optimization performed on the conditional expectations, not on unbiased predictions, would yield the best possible processing choice. We propose a procedure choosing the processing parameters on an approximation of the conditional expectation. The difficulties with the classical approach and the effectiveness of this new approach are illustrated by a simplified simulation example with a single processing parameter and a simple dependence on the microstructure.

Aug 1, 2013

By Sammy Bansah, Komla Dzigbodi-Adjimah

Abstract-Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized ("Banka") drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi- Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration programs for use in similar settings.

Jan 1, 1995

By Sammy Bansah, Komla Dzigbodi-Adjimah

Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized (“Banka”) drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi-Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration pro-grams for use in similar settings.

Jan 1, 1995

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016