Search Documents

By O. Hyvärinen

Outokumpu has developed a new chloride leaching process called HydroCopper®. In this process copper sulfide concentrates are leached at atmospheric pressure in concentrated sodium chloride solution using cupric ions as the oxidant. Copper is recovered from the purified leach solution by precipitating cuprous oxide, which is then reduced to pure copper and further melted and cast directly into copper products. The key reactants: sodium hydroxide, hydrogen and chlorine are generated from the spent sodium chloride using chlor-alkali technology. An important feature in the HydroCopperTM process is that the gold contained in copper concentrates is leached as chloride complexes and recovered from solution by activated carbon. Conditions for the leaching of gold-bearing pyrite can also be achieved in the chloride system by optimizing the redox conditions. This paper deals with the basic factors affecting gold leaching from copper sulfide concentrates. Opportunities for the recovery of refractory gold associated with arsenopyrite and pyrite will also be discussed.

Jan 1, 2005

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By S. E. Wolfe

AKNOWLEDGE of the density of a pulp or suspension is frequently required by the millman, to whom fluctuations in density, which occur in all mill circuits, are of importance and interest. There ,are many w.ays currently in use to determine density and probably the most common method is to take samples of the pulp. The proper sampling of the material is no easy matter, particularly when the pulp contains a sand fraction which settles rapidly. For example, when filling a liter container from the overflow of a classifier, it is al-most impossible to fill the can completely and yet prevent overflow. If there is an overflow, the pulp remaining in the can invariably has an excess of sand and the indicated density will be too high. To surmount such difficulties, and to obtain a continuous indication of the density of a pulp at any desired depth, the simple indicator shown diagrammatically in Figure l was designed by the writer in 1951. Its component parts, numbered as in Figure 1, are as follows.

Jan 1, 1958

By F. L. Pellet, S. Maiolino

"The determination of rock bolt contribution to reinforced joint shear strength is still a challenge, especially for assessing reinforced rock mass stability. For this purpose, several experimental studies have been performed during the last decades, mostly on small scale rock joint and bolt specimens. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for. For this reason full scale lab tests are required as an alternative to in situ tests for which boundary conditions are more difficult to control.In this paper the results of an experimental program carried out with a large shear box, dedicated to test bolts in full scale conditions is presented. Different rock bolt diameters and different rock bolts inclination with respect to the shear plane were tested Experimental results were satisfactorily compared with an analytical model which is able to compute the contribution of the rock bolt to the shear strength of the joint as well the associated displacement of the joint. These conclusions allows us to validate the model in order to help the designer of reinforced rock engineering structures, such as slope or underground openings, to precise the optimum installation of rock bolts. INTRODUCTIONFully grouted rock bolts are commonly used for rock masses reinforcement to ensure the stability of rock slopes and underground cavities. For this purpose, the determination of rock bolt contribution to reinforced joint shear strength is of the utmost importance. During the last decades, several experimental studies have been performed to investigate the behavior of bolted rock joint. For obvious reasons, almost all the experiments were achieved on small scale bolted rock joint specimens (Bjurström, 1974; Azuar, 1977; Dight, 1983; Egger & Fernandes, 1983; Schubert, 1984; Spang & Egger, 1990; Egger & Zabuski, 1991). These studies made it possible to assess the influence of different parameters such as the bolt’s diameter, the number of bolts, the angle between the bolt and the joint, the nature of the rock, the friction and the dilatation angle of the joint. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for (Vallier et al., 2010). For this reason full scale lab tests have been performed as an alternative to in situ test for which boundary conditions are more difficult to control."

Jan 1, 2015

By George Kellock

In presenting this paper for discussion at the Western Annual Meeting to be held in Edmonton, it is with the idea of creating a full and general discussion by the mining men in the Province as to the best way to eliminate, or at least hold down to a minimum, the dangerous coal-dust which is made in mining pitching seams in our Alberta mines by the chute method. Also, an alternative method is outlined, whereby the percentage of lump-coal mined can be increased, and the mining costs reduced-although the paper does not go into any detailed consideration of costs. The general trend of mining practice and lay-outs is at present towards mechanization, and the results being accomplished by the substitution of machines for manual labour are fully justifying the changes. In the technical mining journals, there are published from time to time papers dealing with a variety of methods of mining, which are descriptions of actual operations, and a great deal of interesting and valuable data is given as to the comparative values of the different methods, insofar as the percentage of grades of coal produced, the cost of production, etc., are concerned; but the mechanical methods described in these papers are nearly always suitable only for flat seams, or seams with a very low inclination.

Jan 1, 1929

By Gabriel G. Walton

Conventional numerical modelling tools for analyses of underground excavations are well suited for modelling elastic behaviour and yield response of geomaterials with very simple constitutive behaviour. Non-dilatant elastic and perfectly plastic behaviour is most commonly used for preliminary analyses in the absence of the data required to consider more complex behaviours such as strainweakening and dilation. For truly brittle models, this deficiency is more acute. Current state of practice allows only for reliable estimation of the volume of failure, but not for any prediction of displacement. In fact, there is no consensus in rock engineering regarding the most accurate approach or most suitable tool to model the magnitude of the plastic deformation that strain-weakening or brittle rocks experience at tunnel boundaries, particularly when support is incorporated into these models. This problem is largely a function of a poor understanding of how inelastic dilation occurs in different types of rockmasses, the rate controls on strength loss and volume change during yield, and the complexities of rock-support interaction in yielding conditions.

Jun 1, 2012

By Jinsuo Zhang

Investment in coal resource development is affected by a variety of uncertain factors. Investors can make a flexible, strategic decision to achieve the value of risk implicated in those uncertain factors. Therefore, based on real-option theory, we identified key uncertain factors that affect a coal resource investment project, and revealed the formation mechanism of option value in coal resource developing investment project. Then, a multi-factor decision making model was established for a coal resource development investment project with random changes of coal price, interest rate, convenience yield and production cost. Finally, we tested the model and analyzed relevant parameters by applying living data. Our results indicate this model reflects the value of risk implicated in uncertain factors for coal resource development investment, and is able to determine a critical point of decision making change when coal price and production cost varym respectively. By means of parameters analysis, the convenience yield has a positive effect on the project value. The interest rate has a negative effect.

Aug 1, 2013

By Robert B. Parsons

"First down and four to go. In the game Of football, this is not a bad position to be in. However, in this game of political football, it means that there is still a long way to go. The government in Ottawa has concluded an important agreement with one producing province, and now has at least four more provinces to deal with-B. c., Saskatchewan, Nova Scotia and Newfoundland.On September 1, 1981, the federal and Alberta governments took a significant step forward in formulating an oil and gas policy for Alberta and the rest of Canada on signing a comprehensive five-year agreement that covers taxes, prices, incentives and other fiscal matters related to the production and marketing of oil and gas.This month, Tax Notes examines the main features of the agreement, and offers some eye-opening observations of what the new accord could mean for the future of the Canadian petroleum sector in particular and Canadian business in general."

Jan 1, 1981

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By T. Tsutsumi, S. Kukino

"During the diametrical compression test, the tensile stress generated near the loading plate is influenced by the contact area between the loading plates and specimen. However, very few studies have determined the contact area. Theoretical or analytical models have shown that for an orthotropic material (i.e., with material properties that differ along each of three mutually orthogonal twofold axes), the maximum tensile stress is generated at the center of disk when the angle of the principal material direction to the loading direction is close to ?/4. The maximum value is almost constant, regardless of the contact area. Conversely, the maximum tensile stress is generated near the loading plate when the angle between the principal material direction and loading direction is small. The maximum value decreases as the contact area increases. Therefore, in the latter case, the influence of the contact area on tensile strength measurement of is significant.In previous studies, the distribution of stresses applied on the loading plate is assumed to be a uniform load. In reality, the applied stress is highest at the center of loading plate and seems to decrease with distance from center. The applied load disappears at the edge of loading plates. In this study, in order to satisfy this boundary condition on the loading plate, the cosine curve is adopted as the distribution of load applied on the loading plates in a theoretical model of the diametrical compression test. Furthermore, the elastic solution using boundary conditions shown in this study is used to obtain the tensile stress distributions on the loading axis for an orthotropic circular plane. These distributions are compared with empirical results obtained under uniform loading with a loading plate or concentrated loading in previous studies."

Jan 1, 2015

By Y. Chunhua, L. Chunsheng, W. Sheng

"Countercurrent solvent extraction is the dominant industrial rare earth separation method. For the rare earth separation, with low separation factors and multiple components, designing and optimization plays an important role in reaching product quality and reducing separation plant costs. Based on the theory of countercurrent extraction, cost-efficient methods, such as third-outlet separation and hyperlinked extraction processing, have been introduced following computer simulation. The consumption and fixed investment of industrial practice are compared, by which advantages of the optimized rare earth separation process are indicated. INTRODUCTIONThe rare earths (RE) have outstanding optical, magnetic and electric properties in advanced material applications and have therefore received much international attention in recent years. Liquid-liquid extraction is the major industrial RE separation method and is widely used in the industry. Supported by the government and with collaboration from the institutions and enterprises, China has made great progress in RE separation, and has become the dominant supplier of separated RE products. Complicated by multiple elements and low separation factors, careful design of RE separation processes is vital for the quality and cost of production. The theory of separation is the key to basic of flowsheet design and industrial applications.BASIC SEPARATION PROCESS AND THEORYGeneral ProcessAcidic extractants such as P507, P204 and naphthenic acid, are the most popular extractants in modern RE separation industry. In the general separating process, the extractant is saponified with a base, then ion-exchanged with RE solutions, thereby to provide stable and high RE loading in the extractant to fulfill the requirement of production quantity and quality. The RE-loaded extractant is then countercurrently extracted and scrubbed with RE solutions and the RE element thereby is purified. After the countercurrent extraction process, the RE-loaded extractant is stripped with acid to obtain an aqueous RE product, and prepare the extractant for recycling (Xu, 1995)."

Jan 1, 2012

By Timothy W. Ellis

Gold-based materials have been a mainstay of the electronics and semiconductor industry since the physics was just a laboratory curiosity. Gold is the workhorse material in wire bond, flip chip and off wafer interconnections due to its corrosion resistance, ability to form metallurgical bonds by soldering or cold welding, and ease of fabrication. As the electronics and semiconductor industries grew, so did the use, of Gold in spite of the feature size reduction so elegantly demonstrated in Moore?s law. However, several revolutions in the Silicon miracle are threatening Gold?s place as the material of choice. Although cost is always an issue, the limitations are associated with the chemistry of Gold based alloys. Will Gold remain? Emerging requirements of bioelectronics, photonics and power requirements in conventional device represent new opportunities for Gold to shine. Additionally, as the world market demand for electronic, semiconducting, bio-electronic and photonic technology increases, given the right technology, Gold still can provide value proposition.

Oct 1, 2003

By Bradley Stoughton

The magnetic oxide of iron, F eO4 , contains a theoretically larger amount of iron ( 72.4 per cent.) than any other commercial ore. It is probable that it has originated in many cases by the prolonged exposure of the hydrated oxide, ZF e20 a + 3H20 to heat and pressure which converts it first into hematite, F e20 3, and then into magnetite. It would thus appear as if nature had already done part of the work of removing all the oxygen and that magnetite should be relatively easy to reduce. That it is, in fact, less reducible than either limonite or hematite, is due chiefly to its dense and compact physical structure, which makes it less pervious to the furnace gases, and also to its characteristic action in resisting crushing to a uniform size, with consequent irregularity in reducing conditions within the furnace. The net result is that the magnetic oxide requires more fuel and more time for its reduction in the blast-furnace than any other iron ore of similar iron content and physical condition. There is another very important reason why the smelting of magnetite is more costly than that of hematite, and its treatment viewed with a great deal of adverse prejudice by blast furnace operators, namely, that magnetite decreases the proportion of heat developed by the fuel in the stack of the furnace, and increases the already excessive heat requirements of the heart.

Jan 1, 1924

By T. G. Edgeworth

Some of the historical background of the industry is reviewed, with reference to the different types of reduction cells in use for aluminum smelting. Factors to be considered in cell des1gn involve capital, power, and operating costs. The trend is apparently toward larger cells. The industry is studying new construction materials for cell linings, as well as alternate electrolyte compositions and other design changes which will improve productivity and energy efficiency. The aluminum smelting activity in other countries is briefly reviewed. TODA Y'S industrial production of aluminum is still based on the simultaneous discoveries made in 1886 by Charles Martin Hall in Ohio, and Paul Heroult in France. Up to that date, only about 50 tons of aluminum had been produced in the world, and the price at that time was about $5 per pound. Sucl1 figures must be contrasted with the present world aluminum smelting capacity of over five mil-lion tons per year, and a price of about 25 cents per pound.

Jan 1, 1962

By A. Fischersworring-Bunk

The new inline six spark-ignition engine is the realization of BMW's concept of efficient dynamics at high technological level to achieve the attributes of low weight and high efficiency, The paper presents different aspects of the development and manufacturing of BMW's inline six-cylinder engine magnesium-aluminium composite crankcase, Reference will be made on the AJ magnesium alloy optimization approach to balance between mechanical properties and the high pressure die cast ability requirements, Next to this aspect some mechanical design issues will be covered, with CAE methods playing an instrumental role in the early project stage for the assessment of the compound concept, Due to the compound design chosen, the interface posed challenges to both design and productions, A set of novel techniques has been used to cope with these tasks.

Jan 1, 2006

By J. W. Cox, W S. Jones, A E. Chase

For a long time the Oil Industry has been looking for a logging tool which can determine the quality of the cement job behind casing. Older methods such as Temperature Surveys and Radioactivity Surveys might detect the presence of cement behind the casing, but short of production tests, it was impossible to tell that the producing zones were adequately sealed off from adjacent zones. A new logging method, which is called the •Cement Bond Log, operates on the principle that a sonic pulse transmitted by the casing is greatly attenuated when the casing is strongly bonded to an outer annulus such as cement. The down-hole tool consists of a source of sonic energy which is detected by a receiver situated a few feet away from the source. The amplitude of the detected energy is measured and the resulting signal transmitted to the surface where it is recorded versus depth. Amplitude is a function of attenuation and thus the log is readily interpreted.

Jan 1, 1961

By T. B. Williams

Most geologists have felt the need of a longer base than is ordinarily available when using a Brunton compass or other convenient instrument for taking strikes and dips in the field. To overcome this difficulty a lath or stick with straight parallel sides is frequently used. This accessory adds to the accuracy of the work, but it is a decidedly inconvenient one for the geologist to carry, especially if he be heavily loaded or is travelling on horse-back or through thick brush on foot. The writer has abandoned its use in favour of a sturdy two-foot carpenter's rule. The rule preferred is manufactured by J. Rabone and Sons, Birmingham, England. It is provided with a good level-bubble set in one of the limbs, and a scale, of the protractor type, graduated to five degrees through 180 degrees, attached to the main joint at the middle of the rule. (See Figure 1). For an instrument of its kind it is very accurate, and, in addition to the uses mentioned below, it 'is a handy thing to have around any camp. It is frequently used when plotting roughly in the field and for a protractor when one is not available. When not in use it may readily be carried in the top of the high-boot or legging. Ordinary strikes are measured as illustrated in Figure 1, the compass being held against the rule, which is in a horizontal position. Dips may be measured in a corresponding way by holding the Brunton compass against the extended rule, which is thus used merely as a straight edge. It is usually much more convenient, however, to ? use the rule only for this purpose, in which case one foot of the length rests as a straight-edge against the rock surface. This adaption is shown in Figure 2.

Jan 1, 1929

By Francisco Tamargo

"This paper refers to a new process for the full recovery (above 98%) of zinc and other valuable metals (Pb, Ag, Au) accompanying zinc in its concentrates while iron is separated as a marketable product free of any harmful impurities and suitable for sale to the cement industry. The process has been especially designed to achieve the following goals: maximizing the recovery of zinc and those valuable metals that are present in most zinc concentrates (lead, silver, gold); allowing the recovery of other valuable metals such as indium or germanium that could be present in some zinc concentrates; avoiding or minimizing the need for residue disposal in safe areas as it is the common practice nowadays in the zinc industry. Finally, the process achieves the previously related goals at a competitive cost, in line with the existing more efficient operations while using conventional equipment working under atmospheric conditions. The new process can be easily implemented in those smelters using the jarosite or goethite processes as well as in those smelters using direct leaching as a part of the processing facilities. A study has already been conducted on the use of jarosite in the cement manufacturing process, in the raw mix preparation as well as for a set controller. It shows that use of clean jarosite in the manufacture of ordinary Portland cement can result in improved quality of the clinker. Jarosite showed compatibility to influence the burning characteristics of the cement raw mixes. The presence of SO3 bearing mineral phases such as natrojarosite showed the suitability of clean jarosite for use as a set controller in cement production.INTRODUCTION Iron is by far the most abundant impurity accompanying zinc in its concentrates, and consequently, iron residue disposal is a major environmental concern for many zinc smelters in the world. This is especially true during the last 30 years when environmental restrictions became more and more strict. Much research work has been carried out during the last 30 years to try to find a solution for this important issue, but with little success. Only the jarofix process represents a partial solution to this problem as jarofix is stored nearby the smelters with certain limitations as a non-contaminant residue. However, it does not avoid the need to dispose of an important amount of residues every year, representing an environmental liability. Meanwhile, the number of countries limiting or banning the disposal of iron residues generated by the zinc smelters is growing, so that the solution to this problem is becoming an urgent matter right now. At the same time, the lack of appropriate available land for iron disposal is also a major concern in many cases."

Jan 1, 2016