Search Documents

Vast quantities of cosmic material, ranging in size from fine dust to large meteorites and planetoids, have been colliding with and accumulating on the earth since its origin 4.5 billion years ago. There are less than twenty well preserved meteorite craters and Jess than thirty fossil craters or astroblemes on the present face of the earth. On the moon, there are approximately 200,000 craters on the visible face alone -the largest crater being 132 miles in diameter and attaining a depth of 16,000 feet. Making allowances for the different physical conditions on the moon and assuming that these lunar features are of impact origin, the indifference is that, since primeval time, large numbers of celestial objects have also encountered the earth, but that both the topographic expression of the impact and the objects themselves have been destroyed by weathering and erosion. It may be reasonable to suggest that additions of cos-mic bodies have materially altered the chemistry of the earth's crust from place to place and that the impact of large meteorites and asteroids has created zones of weak-ness in the crust that could be the center of magmatic intrusion and mineralization.

Jan 1, 1965

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By F. J. Gauthier, R. G. Gray

"The possibilities of expanding the production rate from the Copper Mountain Mine have been examined using computer programs for analysing a complete range of data, beginning with the diamond drill assays and embracing all steps up to the final rates of return.Programs have been developed to calculate the mineralization inventory file, a matrix of blocks containing the grade and the type of mineralization estimated for each block. Given the topography, prices of metals and costs, the pit limits are optimized using a three-dimensional technique. Within the pit, ore reserves at any cutoff can be calculated. Mining of the pit is then simulated using an interactive production scheduling program on a timesharing computer. The annual tonnage and grade figures from the production schedule are input to a financial analysis program, where the present value and the rate of return are calculated at various metal prices. The expansion possibilities can be run through the programs with their respective costs, and evaluated using the rate of return on the marginal cash flow compared to the additional capital expenditure."

Jan 1, 1971

By G. M. Brownell

Introduction The Flin Flon mine is located on the boundary line between the provinces of Manitoba and Saskatchewan at a point about four hundred miles northwest of Winnipeg. A branch of the Canadian National railway provides the town of Flin Flon with direct transportation facilities. The property was staked in 1914 and, after a considerable amount of exploration; the Hudson Bay Mining & Smelting Company was organized and brought the property into production in November, 1930 (1). Mining is carried on by open pit and underground methods at the rate of about 4,400 tons per day. Production for the year 1934 was: 99,334 ounces of gold; 1,335,319 ounces of silver; 37,486,054~pounds of copper; and 49,427,280 pounds of zinc; in addition to small amounts of cadmium and selenium. The Flin Flon deposit is one of the largest low-grade ore deposits in Canada with complete hydro-electric and metallurgical plants for the production of blister copper and electrolytic zinc. Previous Work The development of the Flin Flon mine into one of the major mining operations in Canada has created a need for a more detailed geological study of the area. Practically all of the information published to date concerns the general surface features. It is the purpose of this paper to deal more specifically with the ore-body and its relationship to the enclosing rock as revealed by studies made possible through recent underground development. The earliest published report on the area is by E. L. Bruce (2), who made a reconnaissance geological investigation of the region for the Geo-logical Survey of Canada in 1914 and established the main. petrological units. Several years later the area immediately around Flm Flon was mapped in greater detail by F. J. Alcock (3). In the summer of 1934, the area of Missi sediments to the north and east of the mine was studied by J. W. Ambrose. His report has not yet appeared in print but his findings are of importance.

Jan 1, 1935

By Lex L. Udy

External-detonation-generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. The explosives tested include aluminum-sensitized and explosive-sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1979

By Hooman Askari-Nasab

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. The objective of the mine plan is to maximize the future cash flows within the technical and physical constraints. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. In the MILP formulation the slope constraints guarantee that all the overlying blocks are mined prior to mining a given block. Traditionally, the slope constraints have been modeled with cone templates representing the required wall slopes of the open pit mine. The overall pit slopes constructed by these templates are a function of the width and height of the geological block model. Therefore, the overall slopes are fixed in one bearing. This paper presents a general MILP model for open pit mine scheduling with variable slopes constraints. The methodology utilizes a directed graph to capture the precedence of extraction of blocks and pit slopes in different bearings. Depth-first-search algorithm was used to traverse the graph for constructing the slope constraints in the MILP problem. TOMLAB/CPLEX was used as the implementation platform to efficiently integrate the mathematical solver package CPLEX with MATLAB. A case study on intermediate scheduling of an iron ore mine over twelve periods was carried out to validate the models.

Oct 1, 2009

By A. Rahmati

Geological and geo-statistical modeling of the ore deposits play a prominent role in resource and reserve estimation for geo-statistical evaluations. Sheytoor iron deposit is located in the Bafq iron ore district (Central Iran) and in the south-east of the Esfordi 1:100000 sheet. According to the geological data, limestones and dolomitic limestones are situated in the north and central parts of the area, on the other hand, iron ore outcrops are observable in the center, south-west and south-east of the studied area. Meanwhile this ore deposit represents a sulfide one. Based on the boreholes data, geological and geostatistical models of the high and low grade iron mineralization zones were generated by Rockworks v.15 software. The IDW method was selected and employed for processing the collected data and a good adaptation between the results was revealed. The distribution model of Fe concentration displayed a relatively high grade Fe in the center, south and south-east parts of the area. Furthermore, this model illustrated a relatively high grade S and P in some parts of the center, north and south-east of the area. The Fe concentration, in the high grade mineralization zone, was between 45 and 61.5%. In addition, in the low grade mineralization zone, it was between 3.64 and 57.64%. Moreover, in the intrusive granites, the Fe concentration was between 30 and 48.73%. Due to the significant amount of the sulfur in the deposit model, most of Fe-bearing minerals are pyrite, so it is recommended an evaluation on Cu-bearing minerals and their related elements in the area to get done. Additionally, there are too much Fe values in granitic zones which could be caused by possible measurement errors and the geological classification of the area. Therefore, it should be done more carefully.

Aug 1, 2013

By Neil Campbell

"The Pine Point area is on the south shore of Great Slave Lake, 510 air miles north of Edmonton and J JO miles south of Yellowknife, N.W.T. The occurrence there of lead and zinc was reported in J 899 by R. Bell (5) of the Geological Survey of Canada, and in the following years several claims were staked and some prospecting was done. In 1928 Atlas Exploration Co. took over the property containing the discovery occurrences. In 1929 The Consolidated Mining and Smelting Company of Canada Ltd. (""Cominco"") and Ventures Ltd. participated with Atlas in forming the Northern Lead-Zinc Co., which, under the direction of J. M. Bell, carried out 24,499 feet of drilling in the discovery and surrounding areas. Two shafts and many surface pits were also sunk. This work showed that the discovery deposits contain about 500,000 tons of lead-zinc ore, but no new orebody was found.In 1936 D. F. Kidd (11) drew attention to the highly significant space relations between the base-metal discoveries at Pine Point and the projections of certain major Precambrian faults mapped earlier by C. H. Stockwell. Geological work by Cominco in 1940 and subsequent years suggested the presence of mineable deposits within a belt of land including part of the area of earlier field work and extending far beyond it. Between 1946 and 1954 exploration financed by Cominco and Ventures Ltd. included 182,950 feet of diamond drilling, 383 feet of sinking, and 240 feet of drifting, raising, and crosscutting. This work was successful in finding substantial quantities of new ore in places where bedrock is completely concealed.The topography is one of low relief, characterized in many places by swampy muskeg and shallow, marl-bottomed ponds. The area where ore has been found is generally higher ground which, though not well drained, is comparatively dry. It is also marked by raised beaches and a few sand dunes overgrown by small spruce and pine. Bedrock is generally overlain by a variable thickness of hard, glacial boulder clay. This in turn is covered by silt, sand, and gravel, probably deposited from the waters of Great Slave Lake, which formerly extended many miles beyond its present southern shore."

Jan 1, 1949

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks, R. L. Sachdeva

"A combined shaft-electric furnace for the smelting of ores and the melting of metallized iron pellets is being developed. The materials are preheated, and in some cases pre-reduced, in the shaft before being transferred to the electric furnace, where melting or smelting is completed. It has been demonstrated that this combination of equipment will enable much of the relatively expensive electrical energy to be replaced by cheaper energy in the form of oil or natural gas, and preliminary experiments indicate that the total energy requirements for a melting or smelting operation are significantly reduced. Projections based on results obtained from the preliminary experiments indicate that further improvements will be possible when certain modifications to the equipment are completed."

Jan 1, 1968

By Jean-François Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

May 1, 2011

By D. W. R. George, J. L. Stewart

Developments in the last decade, which have contributed to increased productivity and decreased coke rates in the iron blast furnace, are reviewed. Future progress in blast-furnace practice is also considered.

Jan 1, 1966

By L. J. Friedman

The recovery of sulfur dioxide from metallurgical gases for the production of sulfuric acid has been the primary means of reducing sulfur dioxide emissions from nonferrous smelters. Sulfuric acid has been produced from gas originating from fluid bed roasters, electric furnaces, reverberatory furnaces, flash smelting furnaces, Pierce Smith and flash converters, sinter machines, etc. The gas from each of these sources has a unique set of variables that affect the design and operation of the sulfuric acid plant. In addition, the sulfuric acid plant itself has been evolving, with new equipment designs and materials. This paper will review each of the unit operations in the gas cleaning and contact sections of the metallurgical sulfuric acid plant, discussing various equipment designs, materials and the handling of gas stream variables and impurities. The paper updates to 2007 previous works on metallurgical sulfuric acid plants by the authors, and analyzes new equipment and systems, including: FRP or alloy quench systems, alloy converters, towers and pump tanks, heat recovery systems, high efficiency mist eliminators, tower packing, etc.

Jan 1, 2007

By H. C. Gunnings, C. O. Swanson

"The Sullivan mine; at Kimberley in southeastern British Columbia; is the largest silver-lead-zinc mine in the Empire and one of the largest in the world.The original discovery was made in 1892 by four prospectors. Until 1899, when the branch line of the Canadian Pacific railway from Cranbrook to Kimberley was completed, little work was done on the property. In 1900, systematic development was started, and during the next 3 years 5,000 tons of ore was shipped to the smelters at Nelson and Trail. By 1903, some 300,000 tons of ore was developed, and a smelter was started at Marysville, about 5 miles from the mine. However, this smelter closed down in 1907 because of metallurgical difficulties after treating 75,000 tons, and the property came under the control of the American Smelting and Refining Company. An option on the property was taken in 1909 by the Consolidated Mining and Smelting Company of Canada, who exercised their option in the following year. During the next 5 years by selective mining and sorting 188,000 tons of high-grade ore was produced and shipped to Trail. This tonnage came from the upper levels, about 4,600 to 4,800 feet in elevation. At the same time, deep drilling down to the 3,900-foot level showed the presence of an immense body of complex ore. In 1915, the main adit-the 3,900-foot level-was started, and by 1919 this had been driven a distance of 2 miles to develop the ore above this level. Meanwhile, progress was being made in overcoming the milling problems. An interesting account of this work was written by the staff ( 4). In 1923, the first unit of the present concentrator was erected, with a capacity of 2,500 tons a day, and thereafter the rate of production increased rapidly. In 1934 it was around 8,000 tons a day, and to date a total of about 30,000,000 tons of ore has been sent to the mill. In recent years, a considerable part of the production has come from levels between the 3,900-and 3,350-foot, which were opened by an internal incline shaft started in, 1930. In 1942, tin was added to the products separated at the concentrator."

Jan 1, 1954

By Robert B. Parsons

"As the 1981 annual reports of Canadian mining companies one by one see the light of day, it becomes clear that softer metal prices and rising costs are the main problems which beset the industry today. These problems are certainly not lightened by that familiar monster lurking in the shadows-taxation! Recent taxation trends in Canada, and the existing tax regimes for the mining industry, continue to be a major bugaboo.This examination by ""Tax Notes"" of the impact of current taxation trends on the mining industry is based on a speech delivered recently by Robert D. Brown, senior tax partner of Price Waterhouse, Canada, to the annual meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers in Dallas.IntroductionThe purpose of this paper is to tell a story-and it is a story with a moral. The first thing to recognize is that, with depressed metal prices and weakening western economies, high taxes, in and of themselves, are not really the cause of the Canadian mining industry&apos;s present doldrums. However, the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what the future holds for mining men in Canada will equally play an important role in the future development of the Canadian industry. Our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high marginal tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself."

Jan 1, 1982

By Jim Richard

Introduction Electric Vehicle Controllers (EVC) and the Northern Centre for Advanced Technology (NORCAT) have created two generations of Lunar Highland Simulant ?Simulant preparation techniques and equipment resulted from drilling activities in support of Regolith and Environment Science and Oxygen and Lunar Volatiles Extraction (RESOLVE ) ?The purpose of defining the compaction process was to minimize the effect of density on drill testing This allowed other variables including drill bit geometry, auger, RPM, and thrust to be evaluated independent of density ?Density of Highland Regolith falls within a range of 1.40 to 2.29 g/cm3 (p484 Lunar Source Book)

May 1, 2013

By Eric Johnson

"IntroductionHistoricalCyanidation is a leaching process, in world-wide use, to extract gold (and silver) from ores and concentrates. The process has many inherent advantages on account of its adaptability:a. to any scale of operation;b. to a wide range of ore types and mineral associations;c. to a wide range of physical characteristics of the gold particle size, alloy (electrum) or mineral (telluride);d. to relatively simple plant controls and operating procedures;e. to simple marketing procedures and quick cash return.The basic idea for cyanidation was first described and patented by a German chemist, L. Elsner, in 1846. Some forty years later, J.S. McArthur, a metallurgical chemist and R.W. and W. Forrest, medical doctors, all of Glasgow, Scotland, came to realize the import of the discovery and accordingly, registered patents in Great Britain in 1887 and in the United States in 1889. The keystone of the McArthur-Forrest patent registration was the use of weak (0.05o/o) instead of strong (1.0%) solution.The years 1890-1910 saw much progress in equipment design and the advance from batch to continuous processing to increase efficiency and reduce operating costs.In later years, technological progress followed advances in materials of construction and control systems. Current innovations include large-scale equipment, high-capacity thickeners, belt type filters and Steller, candle-type filters for plants using zinc dust precipitation. As well, environmental protection is increasingly a major concern.The technology of gold adsorption from cyanide solution onto activated carbon has made rapid strides in recent years. This has followed the initial efforts of Potter, Salisbury, Zadra and their colleagues of the U.S. Bureau of Mines Research Station in Salt Lake City, Utah, and the field work of Homestake Mining Company personnel, in Lead, South Dakota."

Jan 1, 1989

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By Erik Richer La Fleche

LEGAL RISKS LEGAL RISKS ARE COUNTRY RATHER THAN PROJECT RISKS OTHER COUNTRY RISKS ARE POLITICAL AND MACRO-ECONOMIC RISKS COUNTRY RISKS ARE EXAMINED AFTER PROJECT RISKS COUNTRY RISKS COUNTRY RISKS INCLUDE: WAR AND ARMED CONFLICT TERRORISM AND SABOTAGE CURRENCY INCONVERTIBILTY AND TRANSFER NATIONALIZATION AND CREEPING EXPROPRIATION GOVERNMENTAL BREACH AND REPUDIATION OF CONTRACT CHANGE OF GOVERNMENT CORRUPTION COUNTRY RISKS FIRST NATIONS AND LANDOWNER CLAIMS LABOUR UNREST SINGLE CAUSE ACTIVISTS REGULATORY AND BUREAUCRATIC DELAYS CONFLICT BETWEEN GOVERNMENT LEVELS ETHIC AND RELIGIOUS TENSIONS INTERNATIONAL SANCTIONS TAXATION CHANGES CHANGES IN LAW

May 1, 2013