Search Documents

By Joseph J. Larry

In hard siliceous sandstone strata overlying coal seams, roof bolting is often the bottleneck in the coal production cycle. In the past, these strata have been drilled by pneumatically operated stopers. Although slow drilling is cumbersome and uncomfortably noisy, the stoper was the most effective drill in these harder strata. However, because of the (U.S.) Coal Mining Safety Act, which limits noise levels for operating drills, FMC Mining Equipment developed the water-through-the-drill-steel method of drilling high-compressive-strength strata. Although water-through-the-drill steel had been developed earlier, the real impact of wet drilling techniques surfaced when the dual-boom roof drilling machines were installed at the Virginia-Pocahontas Division, Keen Mountain, Virginia, in 1974. This paper covers some of the technical details of the water-through- the-drill-steel design and its application.

Jan 1, 1979

By Y. Serres

In the past, conventional reflection seismic techniques were not very successful when applied to typical mining exploration: they lacked resolution in the shallow range or were not cost effective. By combining a light earth tamper source, special geophones and field procedures, a stacking process of the returning seismic events using a microprocessor system, and a sophisticated sequence of adapted digital data processing, Mini-Sosie achieves high resolution in the 100-ft to 4000-ft range. Additional advantages result from the very quiet nature of the source and flexibility of the system. Although Mini-Sosie might be used in the refraction mode, or for well velocity logging, it has found its main applications with the reflection technique.

Jan 1, 1978

By L. P. Connolly, M. J. Fraser

"Hydraulic transport of solids has long been an important technique in mining and beneficiation. More recently, slurry pipelines have proved to be economic for longdistance overland transport of many commoditieis, including iron ore concentrates and coal. Now, the Marconaflo system brings the many advantages of hydraulic transport to bulk storage, loading, transportation and unloading of ships and other carrying equipment, thus providing important new means for delivering mineral commodities to market. In this paper, the authors describe the Marconaflo system and the potential economies which can be realized when applying it for loading, transporting, storing, reclaiming and blending a variety of mineral commodities, using several commercial installations as examples."

Jan 1, 1972

By Suman Giri

Non-Intrusive Load Monitoring (NILM) is a method of extracting appliance-level power consumption information from aggregate circuit-level data with the goal of giving users feedback regarding their energy consumption so they can take control of their consumption habits. In this paper, we present a novel algorithm for classification of on and off states of appliances. We compare the performance of our algorithm in on state detection with a pervious paper that evaluated the same dataset and show that it performs up to 13% better. We also present the results of a case study where we collected data for different modes of a cooktop, microwave and dishwasher and used our algorithms to perform power estimation. The error on ten different setups in the test bed ranges from 1% to 32%. We discuss our results and lay out ideas for future work.

Aug 1, 2013

By Blair Hrabi

Introduction; ?Risks Associated with the Resource Estimation Process; ?Limitations of Available Data; ?Geological and Structural Control of Mineralization Trends; ?Recognizing Multiple Mineralization Controls and Complex Trends; ?Accurate Geodomaining; ?Conclusions.

May 1, 2013

By Dharmendr Kumar, Pradip, Beena Rai, Venugopal Tammishetti

"Due to rapid depletion of high grade Indian iron ores, there is a need to utilize low grade fines and slimes. However, these fines and slimes, in their current form, cannot be utilized in steel making due to their high alumina (6-10%) contents. Several beneficiation strategies such as gravity separation, magnetic separation, flotation and selective flocculation are currently being explored for the upgradation of low grade fines and slimes. In our previous work density functional theory simulations were employed to come up with selective flocculants for beneficiation of iron ore slimes. Our simulation results suggested that starch and guar gum are more selective towards iron minerals than other minerals present in the sample. Grinding of iron ore fines becomes necessary in some cases to achieve adequate liberation for removing alumina impurities in Indian iron ores. We have thus investigated effect of grinding of iron ore fines on its selective flocculation-separation.In the present work, we have taken natural iron ore fines from one of the Indian iron ore mines and ground it to -400 mesh (<37 microns) in dry and wet conditions. X-ray diffraction study confirmed the presence of minerals hematite, goethite, gibbsite and kaolinite in the sample. The fine ground samples were used in selective dispersion-flocculation study with corn starch and guar gum flocculants. It is interesting to note that even though the dry and wet ground samples possess almost similar particle size distributions, significant differences were observed in yield and grades of the concentrates thus produced. These differences may be arising due to the coating of alumina containing minerals on iron minerals. We have also studied the effect of addition of dispersant while grinding. Our study suggests that grinding conditions determine the efficiency of the separation process."

Jan 1, 2016

By Frank Arthur Forward

FRANK ARTHUR FORWARD was born in Ottawa and attended the University of Toronto, where he received a B.A.Sc. in chemical engineering in 1924. From 1924 to 1929, he was a smelter operator and research metallurgist with the Consolidated Mining and Smelting Company of Canada Ltd. (Cominco) at Trail, B.C. Moving to Australia in 1929, he was assistant smelter superintendent, Mount Isa Mines Ltd., Queensland, until 1934, when he returned to Canada, spend-ing one year as metallurgist with B.C.

Jan 1, 1970

By John F. Dougherty

Recently, there has been much debate as to the relevance of reporting financial results using the conventional accounting systems, which is based on historical costs, during a period of rapid inflation. In the following paragraphs , the symptoms, if not the causes, of inflation, its detrimental effect on the financial soundness of business in general and the financial reporting changes being advocated to overcome perceived weaknesses in the present financial reporting system in accounting for the effects of inflation will be reviewed. Finally, a course of action as a sound approach to the financial reporting problem will be recommended.

Jan 1, 1978

By Isabel F. Barton, Matthew J. Gabriel, Mark D. Barton

Process control, mine-to-mill optimization, and other mining operations depend on having robust, comprehensive mineralogical and chemical characterization. However, current characterization methods rely primarily on analyzing samples from trenches, channels, blast holes, and drill holes and interpolating between them, and are not always sensitive to some minerals (such as clays) that cause major problems for mining and mineral processing. Continuous characterization is possible with techniques such as hyperspectral remote sensing, which measures reflectance or absorption of light in the visible to near infrared (VNIR) and short-wave infrared (SWIR) regions of the electromagnetic spectrum. Absorption and reflectance features are characteristic of different chemical bond types, so each spectrum corresponds to a different mineral or material. In remote sensing, each pixel in the scanned area has both a location and a spectrum. This makes hyperspectral remote sensing potentially useful for characterizing mine site materials. In this study, we tested a hyperspectral remote sensing system as a method of characterizing the mineralogy and material types at mine and metallurgical sites. Our test site was a small open-pit copper mine and leach operation in the southwestern U.S. We scanned mine highwalls, dump piles, leach pads, and nearby rock outcrops with drone- and tripod-mounted VNIR-SWIR spectrometers. We collected ground-truth data through geologic mapping, sampling, and spot analyses with a portable short-wave SWIR instrument. The results show that the hyperspectral remote sensing system that we tested is capable of distinguishing the types and distribution of spectrally active minerals and other materials in diverse mining settings, including showing wet and dry areas of leach pads; clay and carbonate type and distribution on mine highwalls, leach pads, dumps, and rock outcrops; plant type and distribution; fault zones, bedding planes, and other geological features; and qualitative spectral matches between dump piles and areas of the mine highwalls. Hyperspectral sensing proved particularly sensitive to the presence and type of clay and carbonate minerals, which cause geotechnical and metallurgical problems such as highwall failure, gangue acid consumption, and flotation sliming. Examples will be presented and discussed at the conference. Areas of continuing research include automating and streamlining the data reduction process, integrating hyperspectral data with block modeling and mine planning software, and testing the results of hyperspectral sensing in different geological environments.

Jan 1, 2019

By K. Dinh

The Ground Penetrating Radar (GPR) has been studied for a long time as a non-destructive evaluation (NDE) technology for inspection of concrete structures. Currently, the most widely used technique for interpreting GPR data of concrete bridge decks is the one that based on the amplitudes measured at various interfaces such as asphalt-concrete, top rebar, or slab bottom. The assumption behind this technique is that a sound concrete deck should have the same reflection amplitude at these interfaces while any low number would indicate some sign of deterioration. Unfortunately, this assumption is not completely valid in most cases. As a consequence, the reported test results usually do not reflect real condition of concrete bridge decks in question. The main goal of this paper is therefore twofold: (1) to discuss the limitations of the amplitude analysis method, and (2) to propose a new model that interprets GPR data of concrete bridge decks. The model methodology is based on the comparison of GPR A-scans between two inspections, using the so-called correlation analysis. The results, indicated by the correlation coefficients, are then employed to develop a contour map that estimates different levels of deterioration. The model is then implemented to a case study in order to illustrate its methodology.

Aug 1, 2013

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By Michael Arriagada, Ivan Arriagada

"As mines return to shafts to economically exploit deeper reserves, two methods mine owners use to minimize short term costs are: sinking shafts in phases and refurbishing old, existing shafts. While there may appear to be benefits to utilizing existing infrastructure, often this is not the case, resulting in missed deadlines and added costs. Similarly, if proper long term planning is not executed when sinking a shaft in phases, additional costs and downtime will be accrued. This paper will take an in depth look at both of these options with an eye towards optimizing costs, minimizing downtime, and facilitating construction. INTRODUCTION With the onset of mechanized mining and large capacity trucks, many mines turned away from shafts and began to use ramps to haul ore to surface. However, continual exploitation of mineral reserves located closer to surface, combined with the subsequent unearthing of additional resources at greater depths, forced mines to go deeper and deeper to extend the life and keep the operation running. In shallow mines, hauling ore by truck was an economical option. However, as mines get deeper, driving ramps takes additional time, and hauling over longer and longer distances becomes less economic, both in terms of cost and time. For this reason Mexico, in particular, has seen a jump in the number of shafts which have been put into production, as well as having a number of shafts in different stages of development and still more in the conceptual stages. Many of the shaft projects in Mexico are being designed in phases, with the hoist and equipment purchased capable of reaching the ultimate planned depth of the shaft, but with sinking operations stopping short at an intermediate depth. A loading pocket is then installed to start exploiting mineral at this depth sooner, with subsequent phases planned for a later date using either a rock pentice or bulkhead to separate the sinking operations from the active shaft above. Currently, we are directly involved in two such projects which are actively being deepened, as well as having seen various others already reach completion. If done properly with the long-term plan in mind, sinking in phases can be a very viable option, allowing for faster production while fully utilizing the equipment at various depths. However, there are many issues which can arise when sinking a shaft in phases that if not properly examined and planned for from the outset, have the potential to eliminate the gains hoped for when it was decided to sink in this manner."

Jan 1, 2019

By M. Matthias

A study, part of a doctoral dissertation (Matthias, 1991), was conducted during 1987 and 1988 to establish the means by which professionals assess and maintain their competence during the various stages of their careers. The study elicited responses from fifty-nine subjects representing engineering, pharmacy and medicine (twenty subjects from engineering, nineteen from pharmacy and twenty from medicine) on their perception and assessment of continuing competence. The findings revealed a wide variation of how professionals perceived their continuing competence and the means they adopted to keep current. The implications of the study are significant for adult education practice and theory building. The author strongly believes that now, more than ever, engineers must take ownership of their careers and professional development activities. While management and supervision have a key role to play, it is the engineer, who is ultimately responsible for the scope, planning and implementation of her/ his professional development needs. An example from one high technology company will illustrate these points.

Jan 1, 1999

By K. Mirkhani, P. Gebski, W. Ying

The campaign life of an industrial metallurgical vessels strongly relies on the quality and quantity of the refractory lining. An operating furnace or converter refractory lining can be assessed either by thermal modeling or by acousto ultrasonic-echo (AU-E) technique or a combination. AU-E is a Non-Destructive Testing (NDT) stress wave propagation technique that has been utilized on a wide variety of smelting vessels for over 12 years with good success. AU-E can determine the thickness of remaining refractory lining, estimate the thickness of build-up or accretion, detect and locate metal penetration and impregnation into the lining, and identify hydrated or cracked areas of refractory. This paper details the AU-E principles, equipment and recent improvements to the data analysis to further improve speed and accuracy. In addition, the paper discusses the AU-E accuracy and limitations through a diverse and vast array of practical examples including a comparison with thermal modeling and physical measurements.

Jan 1, 2011

By Gorrell. H. A.

Subsurface water data can be very valuable in .petroleum exploration and research. For the discussion of problems related to subsurface waters uniform nomenclature and classifications are required. The term &apos;connate water&apos; has frequently been incorrectly used. It should .only be used in its original sense in which it is analagous to &apos;fossil water&apos;. Classifications .based on origin and on sodium-chloride content are proposed. Present and possible uses of formation water analyses are briefly discussed. Since the potential uses of formation water data are not fully understood, complete analyses of selected samples should be made to insure against future requirements. The subsurface waters of Alberta show considerable regional variation in amount and proportion of dissolved salts.

Jan 1, 1958

By R. W. Bruce, K. W. Downes

"IntroductionSULPHUR production in Canada from all sources for the year 1953 amounted to about 375,000 tons. Except for 16,000 tons of elemental sulphur derived from natural gas, this production was in the form of by-product pyrites, liquid sulphur dioxide, and sulphuric acid. In the same year, Canadian industry imported 359,000 tons of elemental sulphur from the United States. The cost, including transportation charges, to Canadian consuming plants ranged from $35.00 to $45.00 per long ton, depending upon location.Although most of the sulphur consumed is used in the oxidized form it is often most convenient to buy sulphur in the elemental form, and convert it to sulphur dioxide or sulphuric acid in situ as required. This is because elemental sulphur is easily shipped and stored, weighs only half as much as an equivalent quantity of sulphur dioxide and one-third as much as the corresponding quantity of sulphuric acid, and is readily converted to these forms in a sulphur burner. A process, therefore, which could economically recover elemental sulphur from sulphide ores would be most attractive.Since the turn of the century, notable improvements have been made in extractive metallurgy, but until recently only limited attention has been paid to the possibilities of elemental sulphur recovery. This has been due to the plentiful supplies of cheaply mined Frasch sulphur which have been available on the world markets."

Jan 1, 1955

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By Janet S. Springer

Anomalous gold concentrations in carbonaceous material have given rise to misconceptions about the role of carbon in gold depo its. Some hydrocarbon and carbon-rich black muds may how gold contents raised to 100 time above background by mechanical entrapment. urface effect in fine ediments. and metabolic fixing of gold by micro-organisms. Such concentrates, however, are 10 times too low to be economic. Studie in the Archean of Ontario show that graphite schi t are not the protore to an economically workable gold deposit. A later event of gold introduction ha been uperimposed on the initial low concentrations. Gold enrichment i localized by reduction at vein margins where hear plane . the conduits of mineralization, cut carbonaceou horizons.

Jan 1, 1986

By Sepulvedam Jaime E., Levi Guzmán Rivera

"Grinding media consumption rates and their dependence on key operating conditions in semiautogenous grinding mills is analyzed on the basis of a detailed mathematical model recently developed by Moly-Cop´s specialists which describes and takes into account the three primary media consumption mechanisms, namely: abrasion/corrosion, surface spalling and impact ball breakage. The influence of key mill operating conditions – such as ball filling, discharge grate opening, mill speed, lifter profile, and ball quality – on their corresponding grinding media consumption rates is explored via a variety of model simulations, discussing in every case the independent contribution of each of the indicated consumption mechanisms to the estimated total ball consumption rate.INTRODUCTIONA thorough understanding of the independent contribution of each grinding media wear mechanism is extremely important, especially in semi-autogenous grinding (SAG) operations where macrowear (spalling) and ball breakage cannot be ignored or neglected. The high impact conditions imposed in modern SAG milling environments has created serious challenges for grinding media manufacturers since their products must be able to perform with minimal breakage and surface spalling.GRINDING MEDIA WEAR MECHANISMFor SAG milling operations, at least 3 different mechanisms have been identified as the main contributors to the observed overall grinding media consumption, here referred to as: abrasion / corrosion, ball breakage and surface spalling.Wear by Abrasion/CorrosionThe abrasive/corrosive wear mechanism has been discussed in depth in previous publications (Benavente Hector, 2007; Guzman Levi, 2014; Sepulveda and Morrow, 2014). The most widely accepted approach to mathematically characterize the consumption (wear) kinetics of grinding media in rotary tumbling mills is known as the Linear Wear Theory (Prentice, 1943; Norquist, 1950; Sepulveda, 2004) which claims that—at each instant 't' after a grinding body enters the mill load—the rate at which the body loses weight is directly proportional to its surface area exposed."

Jan 1, 2016

By M. Wittke

"In the course of the extension of the railway network in Israel, currently the two 4.6 km long tubes of the Gilon Tunnels on the line from Akko to Carmiel are being constructed. The tunnels run through the limestones of the Bina- and Yirka-formations, which locally are karstified. The maximum overburden amounts to 160 m.The limestones are mostly horizontally bedded and vertically jointed. Occasionally also inclined joints exist. The tunnels cross various fault zones, which mostly strike at an acute angle to the tunnel axis and are steeply inclined. The karstic cavities which were encountered during tunneling have partially been filled by clay. In the vicinity of the fault zones, the rock has often been strongly jointed and weathered respectively. The two single-track tubes have a cross section with vertical walls and an open invert. The tubes are connected by cross cuts with a spacing of approx. 250 m.During the tender phase, WBI has elaborated the tender design for a joint venture of a Chinese and an Israeli construction company. After the joint venture had been awarded the contract, the preliminary and the detailed design have been elaborated by WBI and the construction works have been guided. On the basis of the geological description, rock mechanical models have been elaborated, followed by stability analyses on the basis of the Finite Element method. The tunnels have been excavated according to the shotcrete method. The support in most areas only consisted of a very thin shotcrete lining and radial bolts in the area of the roof. Depending on the degree of jointing and weathering, locally advancing support by means of spiles has been applied.The internal lining of reinforced concrete has been constructed in parallel to the heading of the tubes. Mucking and delivery of materials was carried out through the cross cuts.The breakthrough was achieved in April 2014 and thus within schedule. The predicted distribution of the excavation and support classes along the tunnel has been in good agreement with reality."

Jan 1, 2015