Search Documents

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By W. G. Hubler

History The Aldermac mine is situated on the Nipissing Central railway near the ' centre of the township of Boischatel, Quebec, and is about ten miles west of Noranda. Aldermac Mines, Limited, is a subsidiary company of Towagamac Exploration Company. The property was staked by Messrs. Alderson and MacKay and McMartin, during the winter of 1922-23. During October, 1925, a copper discovery was made by K. W. Fritzsche, who was in charge of exploration work at that time, the first trench on this discovery averaging 8 per cent copper over a width of ten feet. This led to the discovery of another body 200 feet to the north, with an average of 3 per cent copper over fifteen feet in width. A magnetic survey was then carried out which led to the location of the large pyrite ore-bodies which have been developed in the past few years. Development work was carried on to a depth of 1,125 feet, and approximately three million tons of massive pyrite ore was indicated. Extensive metallurgical tests were conducted in the laboratories of the Mines Branch of the Department of Mines at Ottawa to determine the proper metallurgical treatment and the economic possibilities of the ore. Owing to the comparatively low copper content, and the uncertainty of the copper market, it was doubtful if the mine could be profitably operated for the production of copper alone. Messrs. Alderson & MacKay, however, realized the possibility of utilizing the large tonnage of pyrite as a substitute for native sulphur, 'which in past years has been imported into .Canada for the manufacture of acid and sulphate pulp in paper mills. They therefore organized the Sulphite Research Corporation with the object of developing an economical process of utilizing the pyrite.

Jan 1, 1932

By Walter I. Nelson

THE geology of the Copper Mountain mine has been ably described by Dr. Victor Dolmage in Memoir 171 of the Geological Survey. Reference is invited to that paper for a more extended description of the geology of the ore deposits than will be given here. The important orebodies of the mine occur in fragmencal volcanic rocks, parallel with and adjacent to the gabbro of the Copper Mountain stock. In the mine area, the contact strikes N.45°W. and dips either vertical or steeply co the southwest. For a distance of 500 feet or more from the contact, the fragmental rocks have been intensely metamorphosed both dynamically and hydrothermally. The dynamic effects are reflected in the foliation and fracturing parallel with the contact, which occurs throughout the mine, and the volcanic rocks within this foliated zone are, in places, highly schistose. Superimposed upon thi.s structure is a system of fine, straight, parallel frac-tures that strike nearly normal to the foliation (and contact) and dip between 65° and 75° to the north; it is with this last-described fracture system that the ore minerals are structurally associated. The fractures are mineralized with bornite and, to a considerably less extent, with chalcopyrite and some pyrite. A notable characteristic is the extreme fineness of the fractures; even in high-grade ore they are rarely larger than pencil lines. The tenor of the ore, therefore, varies directly with the fracture spacing. Replacemcnr of the host-rock between two or more fractures, varying in degree from finely disseminated sulphides to masses of nearly solid bornite up to 18 inches wide and 2 to 3 feet long, is not uncommon in the higher-grade portions of the orebodies. Two structural types of orebody are recognized in local nomenclature: the 'contact' orebodies, so-called because they occur along the contact; and 'outlying' orebodics, which are enclosed in the volcanics. The former arc tabular or lenticular bodies elongated along the strike and dip of the contact. The 'outlying' orebodies are coniform, chimney-like masses roughly elliptical in plan; with depth, their roots plunge at steep angles toward the contact. All of the orebodies are cut by a number of light-coloured granophyre and felsite porphyry dykes. These dykes-the so-called 'mine' dykes -enter the mine area from the north, curve gently southeasterly across the orebodies, and then cross the contact into the gabbro at the south end of the mine. All the dykes dip vertical to steeply east.

Jan 1, 1941

By Maurice Morton

THE use of organic and inorganic stains has found wide application as a means of detection and estimation of organic fibres. Such stains have enabled the analyst to distinguish between organic fibres of different type and even between wood fibres produced by different processes. Among these stains, aqueous iodine solutions have figured prominently, as in the case of the well-known Sutermeister and Herzberg stains. At the Johns-Manville laboratories, the idea of applying a stain to asbestos fibres was first considered solely as a visual aid in the microscopic examination of such fibres. The staining medium used in this work consisted of a 1 per cent solution of iodine in C.P. glycerine, the latter being used extensively here as a dispersing and mounting liquid for asbestos fibre. This iodine solution was found to have distinct staining properties when used on the local chrysotile fibres, and to improve greatly their visibility under the microscope. It was soon revealed, however, that this staining is apparently limited to the chrysotile variety of asbestos, as against other varieties. It can be readily seen that, if such were the case, the staining test would become a very useful tool in differentiating between chrysotile fibre and the other mineral fibres, without recourse to a lengthy chemical analysis. Hence this investigation was launched, with the purpose of obtaining more information as to the selectivity of this stain as well as its mechanism. The only previous work of this nature that could be found in the literature was that of Van Winsen and Graham (1, 2, 3) on the adsorption of erioviolet dye by serpentine and related magnesia minerals. However, these authors did not refer to any specific behaviour of chrysotile as against other types of asbestos fibre.

Jan 1, 1941

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By R. Grau

"After commissioning and start-up of the first 500m3 TankCell® flotation cell in 2014, the over 300m3 mechanical flotation cells have earned their place in large-scale flotation operations. These 500 to 630m3 cells, designed for projects with large throughputs, are proven to provide savings in project capital and operational expenditure through savings in foot print, energy consumption, and less equipment to install and maintain. Addition to savings in different phases of a project, these cells provides operational flexibility and has shown improvements in metallurgical performance. In this paper a case study from Kevitsa TankCell® e500 installation and Buenavista del Cobre TankCell® e630 installations will be given.INTRODUCTION After development (Grönstrand and Bourke, 2008), characterization (Morales et al. 2009; Yanez et al. 2009; Grönstrand at al. 2009), validation (Elgueta et al. 2009; Coleman and Dixon, 2010), and more than 350 industrial installations of the Outotec TankCell® e300 flotation cell, the well proven energy efficient TankCell® product family introduced the TankCell® e500 forced-air flotation cell late June 2012 (Outotec.com, 2012). The introduction of the 500 m3 flotation cell followed by introduction of a 630 m3 flotation cell, TankCell® e630, in October 2014 (Outotec.com, 2014). These large flotation cells are designed for projects with high throughputs where the number of cells needed for operation with smaller equipment would become large. The benefits of this size of flotation cells comes from the lower capital expenditures due to lower equipment costs, savings in plant footprint, less installation work with less auxiliary equipment, lower energy consumption, and less units per installation resulting in less components, spare parts and maintenance.The first TankCell® e500 was commissioned and taken into operation in October 2014 at FQML Kevitsa Cu-Ni-PGE concentrator, nowadays owned by New Boliden. The first TankCell e630 was taken into operation in January 2018 at GrupoMexico’s Buenavista del Cobre Cu-Mo concentrator. The start-ups of the first TankCell® e500 and TankCell® e630 followed with test work where the hydrodynamic performances of the cells were characterized and metallurgical performance studied. The results of the TankCell® e500 test work were presented in detail by Mattsson et al (2015a; 2015b) and TankCell® e630 by Grau et al. 2018. In this paper the metallurgical improvements achieved with the large cell installations will be presented."

Jan 1, 2019

By M. J. A. Ruszala

Aggregates production is a huge global industry which uses an enormous amount of energy and produces a massive amount of unsalable fines. Reducing the amount of energy used per tonne of product and/or the amount of fines produced, would make a quarry more efficient. This reduction would make the quarry more environmentally friendly and profitable. This research looks at modelling Mountsorrel Quarry, a granite quarry in the United Kingdom (UK), using JKSimMet and Split-Desktop software packages in conjunction with the European Union (EU) project, EE-Quarry. Samples submitted to drop weight tests confirmed Mountsorrel Quarry granite as an extremely hard granite. Rock fracture data (t10) and energy of comminution (ECS) data were obtained from analysing the results. Split-Desktop image analysis software was utilized to determine the particle size distribution (PSD) of the primary crusher feed, as it contains particles too large to screen manually. It was also found that <1% of the feed is fines, which at Mountsorrel Quarry are classed as particles smaller than 5 mm, and that no particles were larger than 3,810 mm. JKSimMet was used to create a flowsheet of Mountsorrel Quarry. The crusher product PSDs were simulated and found to have strong correlations with experimental data, calculated by screening samples from conveyor belts, especially in the fines region, with a mean difference of 1%. The simulated primary crusher product PSD showed that it contains ~6% fines. A simulation over the entire quarry showed the product to be within the size range produced at Mountsorrel Quarry, and with a simulated fines content of 13%. When the CSS on the primary crusher was altered from 165.1 mm (the operating size on site) to 100.0 mm, it increased the overall percentage of fines produced by 3%, increased the power draw by 140.6 kW, but reduced the overall plant production percentage of fines by 2%. Two blasts were analysed on adjacent rock faces. They had identical blast designs, but the order of deck detonation varied; the first blast detonated the bottom deck before the top and vice versa in the second blast. For each blast, measurements of the feed PSD to the primary crusher, the number of particles that required secondary breakage on the quarry floor, acoustic levels and vibration readings were measured. No significant difference was identified between the two blasts in any of the parameters measured. In conclusion, a working model of Mountsorrel Quarry has been made in JKSimMet that has been validated against data from site and Split-Desktop has been used to simulate the primary crusher feed PSD, something that was previously unknown. The effect of reversing the order of deck detonation in a two deck blast was also analysed but with no significant difference between the two blasts found.

Aug 1, 2013

By G. A. Moruzi

Two sulphide dust secondacy explosions have occurred in the mines of the SUdbury operations of Falconbridge Ltd. during the past 18 months. 'Ihe main similarity between the occurrences is that they both happened in vertical crater retreat blasthole stopes. A relatively high p:,v.tier factor was noted in both instances. other details are enumerated and examined, as well as some results of tests done by Noranda Research on company ore samples.

May 11, 1988

By Ernest Becker

Golder Associates provided overall radiological direction and assistance to the client in their interactions with the Canadian Nuclear Safety Commission and operational radiation protection services for the remediation of a calciner that had been used to process uranium. The project was somewhat unusual in that the radioactivity from within the calciner room was removed from the site and the cleaned steel recycled. The presence of yellowcake within the process equipment required stringent radiation protection measures. This project was completed successfully with minimal radiation exposures to the workers and the effective protection of the environment.

Aug 1, 2010

"Since the publication of a literature review on this topic (McIvor and Finch. 1986), the author has been involved in more than thirty rod milling efficiency tests at seven different milling operations. There have also been several interesting additional articles on rod milling found in the literature. This update describes the most important findings from investigations carried out since the previous review, as well as developments in the techniques used to evaluate the grinding efficiency of rod mills.Rod Mill Power DrawA series of power draw versus charge level measurements were taken on the rod mills at Leg Mines Selbaie and Kidd Creek Mines Limited (McIvor. 1989). These revealed a significant (about 10070) loss in power draw with the installation of new liners, a common observation among rod mill operators. This loss in power draw depends on the liner design, particularly the average thickness and lifting face profile of the new liner. The theoretical power usage of both mills was approximately 5070 lower than that given by the Allis-Chalmers power draw formula (Rowland. 1982).The shape of the power draw versus charge level curve suggested an opportunity for reducing media consumption. By increasing mill speed, power draw could be maintained with a smaller mill load, most significantly for mills operating with high charge levels. Analysis of data from 62 installations confirmed this (McIvor, 1989). On average, a 10 percentage point increase in critical speed results in a 15070 in specific media consumption (Le. kg of steel consumed per kWh of energy consumed). Table 1 lists a number of relatively high speed rod milling installations. No negative effects on the drive train, liner life, or the tendency for rods to tangle have been reported. A reduced lifting angle of the new liner leading face (e.g. 45 versus 90 degrees from the mill perimeter) is recommended for higher speed rod mills (Leclerq, 1990)."

Jan 1, 1995

By C. A. Pickles

Microwaves are being applied industrially in a number of fields and possess a number of potential advantages that could be applied in extractive metallurgy. Microwave heating has a number of unique characteristics, which distinguish it from the conventional heating methods. In microwave heating, the absorption of energy occurs at the molecular or atomic level and therefore the heat is generated within the material itself. In conventional heating, the exterior temperature is usually higher than the interior, but with microwave heating, the temperature gradient is inverted and thus the interior temperature can be much higher than that of the surface. The energy densities in microwave systems can be relatively high and this in combination with the low thermal conductivities of oxide ores, can lead to very high internal heating rates. In this research, the application of microwave energy for the reduction of a nickeliferous silicate laterite ore has been investigated. The real and imaginary permittivities are the two fundamental properties which determine the microwave absorption characteristics of a material and these were measured for the ore, both with and without carbon additions using the cavity perturbation technique. The microwave heating and reduction experiments were performed in a 0 to 2 kW CTC microwave system. The effects of power input, processing time, sample mass and charcoal additions on the microwave absorption were investigated. Then reduction experiments were performed and the nickel grade of the magnetic concentrate and the nickel recovery in the concentrate were determined.

Jan 1, 2005

By A. H. Onur

Spontaneous combustion of coal is a significant hazard in underground coal mines. It causes serious problems for miners for many years after the fact. It threatens workers? lives and causes economic losses for companies. It disrupts coal production and makes it necessary to abandon the main drift where the spontaneous combustion occurred. Coal fires have to be prevented before they occur; otherwise they are very hard to control. Precautions thus have to be taken in potentially risky areas. For coal to spontaneously combust, it needs 3 elements: fuel, oxygen and heat. If one of them is missing, the fire cannot occur. The best way to prevent spontaneous combustion is to prevent contact between coal and air. Coating of the coal surface with an air-proof lining material would be a practical and useful solution to prevent spontaneous combustion of coal. In the scope of this study, a lining material for coating the coal surface was designed at laboratory conditions. Lining material to be used for preventing coal fires should be airproof, cheap, sufficiently strong, have low rebound, be water- and heat-resistant, and easily obtained and applied. It should also be safe for human health when in contact with mine ventilation. By considering these obligations, 3 kinds of gypsum (plaster, satin plaster, molding plaster), as well as lime, cement and fly ash and different mixtures of these materials were applied in laboratory conditions to form a lining material. Samples of lining material were subjected to uniaxial compressive strength tests to determine their behavior against roof loads. Although there is no need to carry any roof load, the lining material has to be sufficiently strong to stay in place on the applied surface. If the lining material is broken, coal and oxygen can react again. Air permeability and curing time of the mixtures were also tested in laboratory conditions. Then the tested mixtures were applied on a wall with a pump to test the applicability of mixtures. After all tests were performed in laboratory, the most suitable mixture was determined as the optimal lining material to prevent coal fires.

Aug 1, 2013

By Osvaldo A. Bascur

Business Challenges ? Many Versions of the Truth ? Lack of Enterprise Visibility (Transparency) ? Limited Communication & Collaboration ? Complex Implementation & Maintenance of software ? End user ease of use of information applications ? Responsive to change ? Access to timely information ? Secure computing ? Maturing Workforce Real time Portal - First of All ? Why Move to a Portal - Portals Recaptures the Business User - Broader Scope - Easy Navigation, World Standard - Features of a Portal - User Profile - Delegation (Secure Delegation of Admin Authority e.g. portal\pat) - Single Sign-On ? HUGE

May 1, 2004

By J. B. Mawdsley

A LITILE north of the geographic centre of the Province of Saskatchewan, 150 miles north of the city of Prince Albert, is a narrow green-stone and sedimentary belt of pronounced structural characteristics. This belt, generally known as the Sulphide Lake belt, is about two and a half miles wide. During the past three years prospecting has uncovered numerous gold-bearing showings occurring chiefly along the centre of the belt for a distance of at least nine miles. The number of these showings, the nature of some of them, and their relationship to strong structural features, make it altogether likely that intensive work will eventually locate ore-bodies that will be of economic importance. The discovery of gold in the fall of 1938 on the south shore of Mackay lake, about five miles northwest of the Sulphide Lake gold-bearing belt, indicates that there are neighbouring zones of interest. This paper, an attempt to outline the present status of the interesting mineralized belt, is based largely on the information gained on a five-day tour of this district, made in August, 1939, on behalf of the Department of Natural Resources of the Province of Saskatchewan. The Sulphide Lake belt is named after a small lake centrally located in it. This lake and others are just north and within short portage distances of some of the long bays along the north shore of Lac La-Ronge, an irregular, island-studded lake, about twenty miles in diameter, in relatively rocky Precambrian country, just north of the Palaeozoic contact. The fur-trading post and settlement of Lac La-Ronge is on the west shore of this lake and a road, now under construction, will shortly link this community with the city of Prince Albert. In the past, the most direct route was an indifferent canoe route, in part following Montreal lake and river; more recently, the aeroplane has made this section easily accessible.

Jan 1, 1940

By R. Stratton-Crawley, S. W. Wilson

"Inco's Matte Separation Plant is a unique mineral processing facility having no process tailings stream. Each product is a high-grade concentrate with strict assay specifications which are defined by the downstream refining route. The most recent column application in the flowsheet, copper scavenging in the production of a high quality nickel concentrate, is described in detail. Testwork in pilot-scale columns (0.038 m, 0.051 m and 0.10 m in diameter) was used to develop a model of the copper scavenging system. This data was then used to simulate the performance of plant-scale equipment. The relationships thus established were confirmed by a series of plant tests in a 1.8 m diameter column. Column results consistently exceeded conventional cell performance. The modelling was extended to assess full plant production requirements and, as a result, a 2.1 m diameter column was specified for this application. Engineering design for this column is currently underway and the column is scheduled to be commissioned later in 1991.INTRODUCTIONMatte SeparationINCO's Matte Separation Plant is a part of the Copper Cliff Smelter complex near Sudbury Ontario. The flowsheet and the development of column flotation within it have been described previously (Feeley et al., 1987, Wilson et al., 1989). The plant feed is a synthetic Bessemer Matte from the Nickel smelter. This matte is slow cooled to promote grain growth and typically assays 46-52% Ni, 23-27% Cu. These elements are present primarily in sulphide form (Ni3S2 and Cu2S respectively) with some metallic alloy also precipitating from the sulphur deficient matte. Minor amounts of iron, precious metals, and nuisance elements are also present.The matte separation process is, in concept, relatively simple. Following magnetic removal of the metallic alloy from the feed, the flowsheet is designed to float a high grade copper concentrate from the nickel sulphide matrix. A simplified flowsheet of the process is shown in figure 1."

Jan 1, 1991

By Fathi Habashi, Ahmet Deniz Bas

"The mechanism of leaching of semiconducting minerals such as PbS, ZnS, UO2, etc., has been the subject of intensive speculation by hydrometallurgy researchers in the early 1950s who assumed the formation of intermediate surface complexes that could be neither separated nor identified by physicochemical techniques. The electrochemical theory of leaching introduced in the late 1960s resolved this problem by comparing the leaching process to a corrosion phenomenon similar to the corrosion of metals. Few years later, experimental evidence showed that anodic and cathodic zones are formed on the dissolving mineral although no electric current is imposed on the mineral during dissolution. A discussion of these findings is outlined.INTRODUCTIONIn the early 1950s researchers realized that kinetic studies for leaching ores are as important as thermodynamic calculations. It was also during this period that the concept of species adsorption on mineral surfaces has dominated the interpretation of the mechanisms of most reactions. This may have been due to the fact that many researchers of this period came from the mineral dressing sector and were influenced by flotation theories. However, when the knowledge of lattice defects and the semiconductivity of minerals became known and their importance in extractive metallurgy was realized, there was a need to explain the leaching reactions in light of these modern theories (Habashi, 1969, 1970). Semiconducting minerals of importance in metallurgy are two categories: the sulfides such as those of copper, lead, zinc, and the oxides such as those of uranium."

Jan 1, 2016

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By J. Y. Kim

This paper presents a novel action recognition method for observing human workers using interactions between actions and related objects on an internal construction site. This method can be used to measure work rates for labour productivity monitoring. This monitoring is critical because the performance of a construction project is significantly impacted by labour productivity. However, construction sites are generally crowded with a large number of workers and objects. Such congestion disrupts the accurate, automatic recognition of construction workers? actions. This congestion is one reason that existing automatic action recognition studies of construction areas mainly focus on workers? actions themselves. However, the crowded conditions mean that sites could offer a great deal of clues that could be used for automatic action recognition. According to psychological studies, interactions clearly take place between human actions and related objects, such as between hammering and a hammer. Humans use these interactions to recognize actions or objects more accurately. On the construction site, workers, materials, tools, and equipment are carefully planned out ahead of actual construction. The categories of workers and objects are pre-defined and, as noted, specific interactions define relations between worker actions and objects. In this paper, the interactions are limited to human workers and their hand-held objects. Action recognition results can be combined with hand-held object information to improve recognition accuracy. With the limited interactions, experiments in this paper show a significant improvement in action recognition. This paper describes the utilization of these interactions to improve construction action recognition accuracy based on human skeleton data and 2D color video from Microsoft KINECT sensor.

Aug 1, 2013

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005