Search Documents

By J. E. Gill

Discovered in 1952, the deposits have been explored by diamond drilling on and near a group of islands in lake Nipissing and from under-ground workings. The ore mineral is a uranian pyrochlore. It occurs in breccia zones in association with calcite, apatite, a?cmite, feldsiiars, biotite, magnetite, sulphides, and fluorite in varying amounts. The pyrochlore concentrations occur in a steeply-dipping gneiss series with some crystalline limestone. Trends indicate a ring structure 114 miles in diameter. The main ore zone shows evidence of repeated brecciation and a succession of replacements .giving rise to a complex of rock types. Pegmatite and lamprophyre dykes cut the ore as do calcite-fluorite veins and later faults with small displacements. Columbium and uranium occur al-most exclusively in pyrochlore, but the proportions vary. There is no tantalum and only small amounts of titanium.

Jan 1, 1957

By Graham Sim

Agenda ?The Water Challenge ?Examples from Three Case Studies ?Mine Drainage, 99% recovery ?Mine Drainage, 80% recovery ?Road Dust Control ?Technology Development ? Conclusion Global water challenges Assuring sustainable quantity Improving water quality Reducing energy consumption

May 1, 2011

By W. B. Boggs

Part 1 Originally, the copper produced at the Noranda ?smelter was shipped in the form of blister bars to the Laurel Hill refinery of the Nichols Copper Co., New York. In 1930 a refinery was built at Montreal East for the purpose of refining Noranda copper and copper from the Hudson Bay Mining and Smelting Co., at Flin Flon. After investigation of the probable costs of making anodes at Noranda and at Montreal, it was decided to make them at Noranda rather than to continue to make blister bars there. Fuel is a major item of expense in making anodes: and since less fuel would be required in making anodes from molten copper than in making them from blister bars, a lower anode furnace cost could be expected at Noranda than at Montreal. Further, the expense connected with making blister bars at Noranda would be eliminated. The cost of treating anode and wire bar furnace slags is a serious item in a refinery, and it was found that the cheapest method would be to ship such slags back to Noranda. With the anode furnace at Noranda, much less anode furnace slag would be made at the refinery. Against these savings which would be effected by making anodes at Noranda must be set the high operating cost of an anode furnace at Montreal, using only tank-room scrap and the Flin Flon copper. This furnace would be handling a comparatively small tonnage and would have a high cost per ton. The usual equipment for making anodes from. liquid copper consists of either a stationary reverberatory furnace or a tilting Tacoma-type furnace together with an anode wheel of the Clark or Walker type. The reverberatory type of furnace has been developed from the furnace used in the old Welsh process of smelting and refining copper, while the tilting furnace is a development of the holding furnace, which is essentially a Peirce Smith converter without tuyeres and provided with burners.

Jan 1, 1932

By M. E. D. Raymont

"During the history of the sulphur industry there have been three distinct phases of production. Factors controlling supplies during these periods have shifted from demand for sulphur to demand for energy and a cleaner environment. The pattern of brimstone production is t raced through these phases and includes estimates of future supply; these indicate an involuntary excess production of some 20 million plus tons per year by 1980 unless some large-scale new uses are found. Traditional uses for sulphur, including fertilizer, chemicals, fibers, etc., are generally expanding slowly; how• ever, supply in ""by-product"" form alone will soon outstrip demand. The predicted oversupply situation can be corrected by the development of novel potential markets. Promising areas include construction materials, insulation and plastics, among others."

Jan 1, 1972

By J. van Deventer

Volatile gold prices in the face of rising costs for mining and refining is causing the mines to look for new ways to reduce costs and increase recoveries. This task is complicated by the fact that the gold in hereto unexploited reserves is associated with increasingly complex ores - either preg-robbing, refractory, associated with high concentrations of copper, or all of the above. Ion exchange resins can play a significant role in this quest for improvement. Although ion exchange resins have been used in Former Soviet Union (FSU) countries for the recovery of gold for many decades, it is still not widely used in the Western World. Synthetically manufactured ion exchange resins can be tailor-made to suit the chemical and mechanical characteristics of a specific application. As such, ion exchange resins can be used in a variety of solution matrices (e.g. cyanide, thiosulphate and acid), and process designs (recovery from clear liquor after solid-liquid separation or directly from the leached pulp). In this paper, a number of applications are discussed along with a review of recent developments in ion exchange technology.

Jan 1, 2014

By A. Aftabi

Abstract-To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2 at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1 ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples are anomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb (>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2 in the southern part of the area. The strong Cu- Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry copper mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sulfide mineralization is present.

Jan 1, 1997

By A. Aftabi

To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples areanomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb(>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2in the southern part of the area. The strong Cu-Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry cop-per mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sul?de mineralization is present.

Jan 1, 1997

By J. D. Aitken

"DEFINITION OF THE REGIONTHE REGION considered in this paper is bounded on the south by the 60th parallel, on the north by the Beau-fort Sea and Amundsen Gulf, on the east by Archean rocks or by highly deformed Proterozoic rocks of the Canadian Shield (certain weakly deformed Proterozoic strata being regarded as belonging to the Great Plains), and on the west mainly by the Mackenzie and Richardson Mountains.Only the unmetamorphosed strata of the region are considered; that is, the geology of the crystalline basement is ignored.SIGNIFICANCE OF THE REGIONThe region is significant from three points of view -namely, the economic, the scientific and the social. It constitutes 46 per cent of the area of the Western Canada Sedimentary Basin."

Jan 1, 1970

By G. H. Hope, A. R. Maycock

"La Mine Doyon is a gold mining operation located in northwestern Quebec, approximately 35 km east of Rouyn-Noranda and 85 km west of Val d&apos;Or. The mine is jointly owned by Lac Minerals Ltd. and Cambior Inc. with Lac Minerals as the manager. Production statistics as of February 1987 are 6.4 million tonnes milled at an average grade of5.8 g/t Au. Current reserves of9.9 million tonnes at 5. 7 g/ t Au to a depth of400m have been outlined. Indicated reserves below this horizon could considerably increase this reserve.The mine currently consists of two open pit and two underground mine operations, producing approximately 3600 tonnes per day of ore at an average grade of6 g/t. The ore is currently processed at the La Mine Doyon mill at a rate of1400tid and at Lac&apos;s East Malartic mill at 1950 t/d. Ore is also processed intermittently at Lac&apos;s Les Terrains Auriferes mill and at Noranda&apos;s Horne Division.La Mine Doyon is currently in the midst of a program to expand and upgrade the mill at La Mine Doyon. The expansion to 3000 t/day includes the conversion of the existing crushing and grinding circuits to a SAG (semi-autogenous grinding) mill circuit and the existing filter wash plant to a CIP (carbon-in-pulp) recovery plant. The economics of this project are based on reduced operating costs (milling and trucking) and improved recovery due to updated technology. HistoryThe area between Noranda and Val d&apos;Or has a long history of mining activity in both base metals and gold, dating back to the early 1930s. More recently, several new orebodies have been discovered and exploited in the area including La Mine Doyon, Lac&apos;s Mine de Bousquet, Dumagami, and the Kiena operation.La Mine Doyon was discovered in the early 1970s, and brought into limited production in late 1979. The mine was started on are reserves of 2.75 million tonnes at 6.2 g/t and was, thus, considered a small, short-term operation. Mining started at an initial rate of 550 tI d with all the ore being shipped to Noranda&apos;s Horne smelter as flux. When Lac&apos;s East Malartic mill became available for custom milling, Doyon commenced shipping to that facility at a rate of 650 t/d. As a result of some equipment additions and an improved understanding of the ore, the East Malartic mill throughput was gradually increased from 650 t/d to the current rate of 1950 t/d."

Jan 1, 1988

By V. S. Sastri, M. Elboujdaïni

"Corrosion rates of silicon brasses, highzinc yellow brass, low-zinc yellow brass, leadedtin bronze and silicon bronzes in both permanent-mold and sand-cast conditions were determined in soft water of pH 3, 5 and 8, and hard water of pH 8 at 70°C by electrochemical polarization technique. The alloys in permanent- mold condition showed greater corrosion resistance than sand-cast condition. Corrosion rates obtained from weight loss measurements showed no observable trend of a difference between permanent-mold and sand-cast alloys.The corrosion rates decreased with increasing pH of the medium. Silicon bronze and silicon brass showed high corrosion resistance while leaded-tin bronze showed the least resistance. Addition of small amounts of aluminum improved the corrosion resistance of silicon bronzes and silicon brasses. Alloys in permanent- mold condition showed greater resistance to dezincification than sand-cast alloys when average pit depth parameter is considered."

Jan 1, 1997

By Viraj Parekh, Kinnor Chattopadhyay, Sina Mostaghel, Xiao Zhang

Electric arc furnace steelmaking is a dominant approach in North America and controlling EAF emissions is a key issue today because of stringent permit limits imposed by various regulatory bodies. In the present study, an attempt has been made to mathematically model EAF emissions, and use the models as a predictive tool for fine tuning the process. CFD modelling has been used to model various fume release scenarios, and optimize the exhaust conditions for maximum capture. Thermodynamic calculations have been used to analyze various chemical reactions which lead to the emissions of hazardous air pollutants with special emphasis on Zinc, Lead and Manganese.

Jan 1, 2015

By J. Bakos

Solar Hydrogen Energy Corporation (SHEC Labs) recently constructed a pilot-plant to demonstrate a Dry Fuel Hydrogen Generation System that is powered primarily by sunlight focusing-mirrors. The pilot-plant consists of: A Solar Mirror Array and Advanced Solar Concentrator and Shutter System; and two thermo-catalytic reactors to convert Methane, Carbon Dioxide, and Water into Hydrogen. Results from the pilot study show that Solar Hydrogen generation is feasible and cost-competitive with traditional Hydrogen production. More than 95% of Hydrogen commercially produced today is by the Steam Methane Reformation (SMR) of natural gas, a process that liberates Carbon Dioxide to the atmosphere. The SMR process provides a net energy loss of 30 to 35% when converting from Methane to Hydrogen. Solar Hydrogen production provides a 14% net energy gain when converting Methane into Hydrogen since the energy used to drive the process is from the sun. The environmental benefits of generating Hydrogen using renewable energy include significant greenhouse gas and criteria air contaminant reductions.

Jan 1, 2005

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By M. P. Davies

"Risk, the product of probability and consequence, is an integral part of mining. Whether evaluating exploration priorities, determining property acquisition potential, reviewing the components of an operating mine or assessing environmental/closure issues, the concept of minimizing risk is central to economic and technically appropriate decision making.Until recently, risk evaluations have tended toward a strongly mathematical basis. With this previous trend, it was essential to establish precise probability density functions to all assessed components or issues where often little information was available. The combined effect of the seemingly complex analyses with corresponding insufficient data often resulted in either a poorly executed risk evaluation or no evaluation whatsoever; either result not acceptable for optimal decision making. This paper presents a simple and practical procedure to carry out risk assessments for the mining industry. Although simplistic in nature, the power and usefulness of the technique is immense. The basis for the procedure involves combining deterministic assessments (often “gut feel”) with appropriate probabilistic descriptors. The resulting procedure, termed Potential Problem Analyses, or PPA, can be used anywhere an evaluation of risk will assist in optimizing technical and/or economic decisions. As will be shown, a key element of the PPA procedure is the multi-disciplinary input the framework allows which makes the method ideal for a teamwork approach to decision making."

Jan 1, 1997

By J. Awmack, M. A. Tomlinson, P. J. Lind

"Peñasquito is a complex polymetallic deposit containing gold, silver, lead, zinc, and copper and is one of the largest producers of gold in Mexico. Mining activity is currently transitioning to a second open pit, Chile Colorado, which will be mined concurrently with the existing open pit, Peñasco. The ore bodies are located within diatreme pipes and into the surrounding sediment formation. In the coming years, mining will be carried out in more sedimentary zones, which are significantly higher in organic carbon content. Organic carbon in the feed influences both flotation and leaching operations. Several changes are being implemented to the Peñasquito flowsheet to mitigate the effects of increased organic carbon in the plant feed. These include the use of alternate reagent schemes, construction of a carbon pre-flotation circuit, implementation of a pre-leach flotation circuit ahead of pyrite leach, and evaluation of a tertiary process for separation of carbon and precious metal minerals.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas in the Mazapil municipality (Figure 1). Peñasquito has been in operation since 2009, with mining carried out by open-pit methods. Oxide ore has been processed in a heap leach facility and sulfide ore is treated in the sulfide processing plant. The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 465,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead in lead concentrate, and 263 million lb of contained zinc in zinc concentrate (Goldcorp Inc., 2017). To recover more of the contained gold and silver and to mitigate the impact of increasing organic carbon content in the ore, a number of significant changes are being made to the operation."

Jan 1, 2018

By J. D. Christian

WHEN mining development began in the Kirkland Lake camp, twenty-five years ago, there was very little information obtainable from surface showings as to the nature of the ore deposits. A length of almost a mile of the main &apos;break&apos; lay under the south arm of the lake, and elsewhere most of the outcrops were covered with glacial drift. Shafts were sunk on ore-bodies of uncertain value, either on the outcrop of the veins or-because of the lake to the north-in the south or hanging-wall. In the second year of the camp&apos;s development, the Great War broke out and retarded progress for its duration. He would have been a real optimist who, in those early years, could have foreseen mining at depths of more than a mile.

Jan 1, 1939

By J. Mizera, J. Zdunek, K. J. Kurzydlowski, A. Dobkowska

This work concerns comparison of corrosion resistance of the aircraft aluminum alloy composed of Al - 2.3%Li - 0.1% Zr. The alloy was hot rolled (HR) from 13 mm to a thickness of 4 mm (e = 2.4) and 1 mm (e = 5.2). Corrosion resistance was investigated by Potentiodynamic Polarization Test. The investigation relied on exposure samples in two different corroding medium: 0.5 M NaCl solution and 0.01 M Na2SO4 solution with added 0.01% of Cl- at room temperature. Furthermore, the microstructure was analyzed using the optical microscope with polarized beam. The hardness was measured on lengthwise profile. It was stated that alloy after the largest deformation (equivalent total strain e = 5.2) is characterized by the best mechanical properties and the best corrosion resistance. The alloys in initial state and after deformation to 4 mm (e = 2.4) are characterized by worse corrosion resistance. It is associated with microstructure and density of dislocation in analyzing material.

Jan 1, 2015

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By M. Djivre, T. Eger, A. Godwin, I. Bhattacherya

Load-haul-dump vehicles (LHDs) are extensively used in underground mining, however, equipment design and operating conditions contribute to restricted operator sight lines. The inability to clearly see people, objects, or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, line-of-sight assessments are traditionally completed in the field. However, field methods are unable to evaluate lineof- sight under dynamic operating conditions, and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height. Results of this research show computer simulation and virtual reality can be successfully used to evaluate line-of-sight during the operation of LHD vehicles. In order to benefit from virtual reality applications, the work environment, LHD vehicle, and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic analysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHDs were developed from manufacturer specifications and pictures taken from LHDs currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle, and the vehicle and human were driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired line-of-sight were successfully identified with this method. The JACK program could also provide real-time feedback on the human’s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHDs evaluated in the JACK software package can also be combined with mine models and imported into other VR software packages (e.g. Blender) in order to enable viewing in Laurentian University’s Virtual Reality Laboratory. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial vision issues.

Jan 1, 2005