Search Documents

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By J. G. Kelly, C. P. Brown

"In June 1983 a new borehole hoisting system was commissioned at Sherritt Gordon's Fox Mine. Twelve hundred tons-per-day of ore from the 2600 and 2800 levels are being hoisted to the 2000 level through an 8-jt diameter bored winze. This new method replaces the diesel truck haulage system which had been in operation at the mine since 1975.A study was initiated in 1980to determine the most effective method of achieving the required production. The study examined several hoisting alternatives including: expanding the existing trucking system; converting to electrically -powered truck haulage; and deepening the skip compartments of the existing main shaft. The alternative selected as the hoisting method most suited to the requirements was borehole hoisting.Development of the new system commenced in April 1982. Underground excavations included 700 feet of 8-ft diameter borehole, a hoistroom and headframe, storage bins, and a grizzly and rockbreaker station. Equipment installations included: a 5-ft diameter double-drum Nordberg hoist; a counterweighted Kimberley-type skip; two rockbreakers; and the steel sets in the winze. These installations were completed in June 1983. Some problems were encountered after the initial commissioning but these were solved, and since August 1983, the system has proven that the designed capacity is achievable within expected costs."

Jan 1, 1985

By L. D. van Dyk, G. S. Tshofu

Iron ore fines are by-products of iron ore mining operations. Unlike iron ore lumps, fines cannot directly be used in conventional iron making processes, and consequently large quantities accumulate around the world. Pelletizing and sintering can be used to convert iron ore fines into agglomerates or briquettes for processing with lump ore, but these techniques are energy intensive and produce greenhouse gases. This research investigated the extraction of iron from iron ore fines using acetylacetone (a ß-diketone) as an environmentally friendly alternative process for fines utilization. A 2k factorial experiment design was used to identify the significant extraction variables. It was found that the reaction temperature and solid to liquid ratio had significant effects on the extraction process. The extraction kinetics were studied at different temperatures and the highest iron extraction (97 %) was obtained after 48 hours at 413 K and 0.025:1 (g:mL) solid to liquid ratio for a particle size range of +106 to -150 µm. The extraction products were easily separated from the unreacted acetylacetone by flash distillation and iron(III) acetylacetonate crystals were recovered. An economic evaluation showed that selling the crystals was profitable. Alternatively, the crystals can be reduced with hydrogen to iron particles and acetylacetone (for reuse).

Jan 1, 2015

By Åke C. Rasmuson, Mahmood Alemrajabi, Kerstin M. Forsberg, Kivanc Korkmaz

"In the present study the recovery of a Panasonic Prismatic Module 6.5 Ah NiMH 7.2 V plastic casing hybrid electric vehicle (HEV) battery was investigated, separately processing the anode and cathode electrodes. The composition of the electrode materials was determined by total dissolution and analysis using ICP-OES. Nickel is the dominant metal in the active materials (65% by mass in the anode and 70% by mass in the cathode). Most of the rare earth elements (La, Ce, Nd, Pr and Y) are located in the anode active material, whereas only a small amount of Y is found in the cathode material. The electrode materials were further characterized by SEM-EDS and powder XRD. The electrodes were leached in sulfuric acid and in hydrochloric acid under different conditions. The dissolution was followed by taking out samples and analyzing the concentration of REE, Co, and Ni using ICP-OES. The results indicate that the dissolution of nickel could be limited by slow dissolution kinetics of nickel oxide. Further, it was found that light rare earths are lost through precipitation during sulfuric acid leaching with increasing extent as the temperature and sulfuric acid concentration increases. The separation of REE from the sulfuric acid leach liquor by precipitation as NaREE(SO4)2.H2O and from the hydrochloric acid leach solution as REE2(C2O4)3.xH2O have been studied by performing experiments using battery leach liquors. INTRODUCTIONIt is well known that the Hybrid Electric Vehicle (HEV) is becoming more common due to economic and environmental reasons. Batteries are widely used in HEVs’ such as automobiles or larger trucks for transportation purposes. The most common type of battery in these vehicles is nickel metal hydride (NiMH), largely due to Toyota's decision to use them in their popular Prius. More than two million hybrid cars worldwide are running with NiMH batteries, such as the Prius, Lexus (Toyota), Civic, Insight (Honda), and Fusion (Ford). Panasonic manufactures HEV prismatic NiMH batteries that have been used by Toyota and GM (among others), while Sanyo manufactures HEV cylindrical cell NiMH batteries, which have been used by Honda and Ford."

Jan 1, 2016

By Imre Gombköto, Barnabás Csoke

"Raw material management means not only mining and processing of primary raw materials like ores, but means also collecting and processing secondary sources of raw materials. Recycling is one of the most developing field of raw material management in Europe, and its solutions are derived from mineral processing roots and principals. Complexity and challenges of the field of recycling results innovative solutions of material processing- Since European Union identified 20 raw materials as critical (CRM) due to lack of primary sources within the border of the EU, recycling become more recognised as source of different raw materials. WEEE is the waste streams contains many of the critical elements and along them at least 15 different species of plastics of which recycling is delayed by a lack of effective separation technique. Most paper deals with separation methods based on different specific gravity, triboelectric charge or surface properties of plastic species. Plastics however have differences of thermal properties and thermoplastics, duroplasts and elastomers can be recognised. The experiments described in the paper aimed to determine thermo adhesive behaviour of plastic species often identified in WEEE streams for separation purposes. According to the results, some plastic types as PS, PP. PC or PVC and PET pairs are possible to easily separate from each other, however different additives are changing thermo adhesive properties of most of the plastics that makes industrial process difficult to develop. Along thermo adhesive behaviour, combination of physical interaction can be used to enhance separation selectivity.INTRODUCTIONPlastics has a relatively long term of history as a light, multi-functional material in construction, packaging, automotive industry and electric and electronic products. There are a numerous types of plastic species can be used for various applications therefore they amount are growing from year to year. This quantity however become part of the waste stream and while metal recycling has been done for decades due to its economic value - cheap plastic parts are less desirable as secondary products. In 2013 an annual 5% of plastic production growth has been estimated with a base data of 265 million tonnes at 2010 (Guiqing & Zhenming, 2013). Since landfill requirements are increasing while—especially in Europe where actual regulations are trying to deflect waste from landfills - landfill capacities are decreasing, costs are become more and more expensive, Applications like energy production based on plastics as a fuel or recycling are some of the options can be applied. Direct incineration of plastics are applied at many plants - in most cases where waste consist of dangerous substances are incinerated because plastics high calorific value helps correct average mixture composition enable operators reaching high enough temperature for combined power and heat generation while most of substances—like PAH, PCB or dioxins—are destroyed. Another path is using low temperature reductive cracking due to pyrolysis process, however the chance having higher concentrate of carcinogen substances in the products are higher since it applies around 400°C during the process."

Jan 1, 2016

By J. K. Shaw

The science of low temperature engineering is well entrenched in mining. Uses for common cryogens, including liquid oxygen (LOX), liquid nitrogen (LN2), and liquefied natural gas (LNG) in the gas and minerals industries are reviewed. Potential future applications are discussed within the scope of mining, particularly in refrigeration and ventilation. The second part of this paper focuses on the Linde cycle, which is at the heart of most liquefaction plants. Steady state equations describing the mass and energy flows are presented. The paper concludes by explaining the concept of a wind powered Linde- Hampson cryogenic cycle and assessing, with scoping calculations, the technological feasibility of producing cryogens with an intermittent source of (renewable) energy.

Aug 1, 2013

The integration of mining and mineral processing technologies into new advanced mining systems is considered to offer several benefits, including selective mining, reduction in waste, increased productivity, flexibility, and improved resource utilization. This paper focuses on underground hardrock mining and the integration of pre-concentration technologies into future mining systems as representing realistic, shorter-term integration options. Control of fragmentation to optimize grinding, pre-concentration of ores, in situ leaching, and modular mining/mineral processing systems are possible with existing technology. Current research is directed toward development of integrated underground systems that minimize surface activity and minimize or eliminate surface waste disposal. Results from a simulation model of an integrated underground pre-concentration system are presented.

Jan 1, 2002

By Terence M. Gordon, Mati Raudsepp, Gregory M. Dipple

Four methods of measuring mineral abundance in a rock are examined for their potential in assaying for high-tech industrial minerals. One method uses X-ray powder-diffraction data and the other three rely on whole rock chemical data and information on mineral assemblages and mineral compositions. All four methods were employed to estimate wollastonite content in diamond drill core of skarn collected as part of an exploration program and are compared to visual estimates of wollastonite content from core logs. These techniques for assaying wollastonite span a considerable range ofaccuracy and expense, and combined, define a non-linear relationship between these variables. Accuracy increases rapidly relative lo expense up to total costs of about $50 per analysis. Assay methods in the $50-100 per analysis range have associated errors of 5-10% relative and probably suffice for most exploration programs. Improvements in accuracy above this level require a much larger investment. The most expensive assay technique (-$300 per analysis) yields the most accurate measurement of grade (relative error -1%). Its application may best be limited to periodic checks on other assay techniques and for fine-tuning ofmineral separation procedures.

Jan 1, 2001

By Xiaoguang Zhao

The coal mining area in Northern Shaanxi, China, has been taken as the study area, and the damage mechanism of the ecological environment is discussed on the basis of analyzing the characteristics of natural eco-environment and resource development in this area. Mining subsidence is taken as an example, and by using the Gray Correlation Analysis method, the key impact factors have been selected. An assessment model with fuzzy comprehensive evaluation has been constructed, and 12 coal mines have been quantitatively assessed. This paper also constructs an ecosystem health assessment method and index system in the coal mine area on the basis of ecosystem health theory, and assesses the ecosystem health status in the Shenfu coal mining area from 2000?2006. The research results are expected to help the eco-environment protection process in the designated coal mining area.

Aug 1, 2013

By J. E. Hawley

Abstract Spectrographic methods for the analysis of minor constituents such as platinum-group metals, gold, silver, and silica in palladium and platinum refinery sponge are described. These involve the conversion of the sponge metals to the black form by reduction with high purity aluminum filings in either acid or alkaline media. Standards of known composition are prepared in the same manner from either refinery or spectrographically standardized sponge metals. Samples of the black metals are mounted in pellet form and a multisource spark discharge used for excitation. The range of concentrations of impurities studied are those common to refinery samples. Excellent reproducibility of intensity ratios using major constituents as internal standards, is demonstrated and two methods have noted by which the accuracy of the procedures are shown to be of the order of 3 per cent, on the basis of synthetic preparations. Introduction During the past two years an investigation has been carried out in the Spectrographic Laboratory, Queen's University, to determine the suitability of modern spectrographic techniques for the precise analysis of the platinum-group metals palladium, platinum, rhodium, iridium, and ruthenium in the form of refinery sponge analyzing about 99 per cent of the major constituent.

Jan 1, 1951

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By J. Clark

Erosion control during the mining cycle can be more effectively planned using Erosion and Sedimentation Control Plans (ESCPs). This raises the issue of who should develop an Erosion and Sedimentation Control Plan Guidance document (ESCPG) to standardize the content of ESCPs. A search for ESCPG documents in Canada revealed no examples for mine sites. In the U.S. there are a number of regulatory authorities who developed such documents for mine sites, including EPA. An ESCPG is expected to result in: (a) plans will be more standardized (b) more clarity and efficiency for those generating ESCPs; (c) assisting regulators tasked with reviewing/approving ESCPs; (d) providing guidance for the mine effluent permitting process relative to sediment control; (e) providing a basis for developing and including ESCPs in the Environmental Assessment (EA) phase and the mine economic assessment; (f) applying and optimizing ESCPs above the ?watersheds? of sediment ponds; (g) utilizing the ESCPG document for ?exploration? sites; (h) lowering the risk of adversely impacting water quality downstream of mining activities; (i) providing a methodology for determining the need for sedimentation pond(s) during the construction and production phases; and (j) providing a clear environmental sustainability message relative to sediment control if the mining industry takes the lead in developing an ESCPG. ESCPs will proactively create increased administrative (regulatory) efficiency in the EA and sub-EA reviews relative to erosion control and sediment release from mine sites. This also assists the new initiative in BC, One Project, One Process (OPOP) and synchronous permitting (a variation of concurrent permitting): as an example, enhanced erosion control planning at the EA phase then allows the synchronous permitting initiative to proceed efficiently, particularly for the mine permit (Ministry of Energy, Mines and Natural Gas) and effluent permit (Ministry of Environment). Approximately twenty more management plans (e.g. ARD/ML, explosive management, emergency response, hazardous waste, sediment pond operation, environmental effects, environmental sampling, etc.) may also be entered into the EA process to create increased efficiency, and then feed into the synchronous permitting effort. The BC OPOP initiative also adds support to the Canadian Federal ?One Project, One Review Process? approach. The ESCP and a sediment pond management plan will also address the Canadian Metal Mining Effluent Regulations requirement for all discharges from mine sites to meet a grab sample of 30 mg/L Total Suspended Solids.

Aug 1, 2013

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996

By D G. Boxall

As an alternative to heavy water cooling, reactors cooled by organic liquids are being actively developed in Canada under the sponsorship of Atomic Energy of Canada Limited. One of the areas in which development has been required is that of core materials. The factors affecting the selection of fuel canning and coolant tube materials are discussed. It is shown that S.A.P. is a potentially attractive material for these applications. The fabrication of fuel sheathing is discussed. Difficulties met due to large inclusions and blistering due to high hydrogen contents have been overcome by magnetic separation and vacuum sintering of the powders. High-quality tubes can now be produced by extrusion to finished size. A study has been made of the mechanical properties of fuel-sheathing tubes and bar stock. The stress rupture properties of the tubes subjected to uniaxial and biaxial stress have been determined. The biaxial stress tests were performed by internal pressurization. For times in excess of about 200 hours, the curve of stress against time to rupture is extremely flat. The secondary creep rates of

Jan 1, 1965

By Tim Watson

Andacollo Hypogene Project ?Overview Project description: Sulphide copper concentrator Throughput:55,000 tpd Location: Approximately 50 km from La Serena Elevation: Approximately 1,000 m ASL Start feasibility study: July 2005 Start of construction: May 2007 Construction completion: December 2009 Final cost(1,2,3):435 Million US $ (1) Excludes third party costs, 220 kV power line (2) Cost is based on a Chilean Peso to US Dollar foreign exchange rate of 535 to 1 (3) Does not include US$40.3 million for the Elqui River Pipeline Project or US$8.0 million for the stock pile cover

May 1, 2010

By H. Lazreg

This paper presents an evaluation of surface resistivity techniques as a tool for delineating salt-water intrusion in Shippegan, N.B. The study consisted of resistivity profiling, resistivity soundings and a limited number of induced polarization soundings in selected areas in the Province of New Brunwick. The results from resistivity profiling indicate that when seawater intrusion occurs in a sandstone formation the resistivity contrast is sufficiently large to allow a precise delineation of the intrusion. A formula is then derived to convert resistivity values to chloride concentration in the "cone of intrusion". The results from resistivity soundings showed that shaly formations may have resistivities as low as seawater-contaminated sandstone. An indeterminacy has resulted from this resistivity overlap. A limited number of IP soundings were performed in an effort to resolve it. The results showed that IP can be of appreciable help in resistivity interpretation.

Jan 1, 1972

The Nak?azdli First Nation and the municipality of Fort St. James are located in the Stuart Lake/Nak?al Bun area and are not unfamiliar to mining. These northern British Columbian communities have been associated with the historic Pinchi Lake Mercury mine and today are closely linked with British Columbia?s newest mine, the Mt. Milligan mine. Prior to the construction of Mt. Milligan, community health and social service providers were concerned about potential impacts that would occur from new mineral development activities. This concern has led to a partnership between the above communities and researchers with expertise in the area of mining and health. This paper describes: the current mining and health environment with a focus on British Columbia; mining trends in the Stuart Lake/Nak?al Bun area; the current community-based health research project funded by the Vancouver Foundation and the Canadian Institutes of Health Research, and; a suite of community-based health recommendations to mining companies on key issues to consider when developing projects near municipalities and Aboriginal communities in Canada, based upon one of the newest mines under development in Canada.

Aug 1, 2013

By D. M. Richards

"IntroductionThe Highland Valley Copper partnership was formed in July 1986 as a logical result of a mine with a large ore reserve but a small mill, and a mine with a large, modern mill but dwindling ore reserves. The original partnership of Cominco and Rio Algom was expanded in January 1988 to include Highmont Mining Company. During 1988/89 the Highmont mill was moved 7.5 km to adjoin the Lornex mill, becoming the Highland mill in the process, with a nominal capacity of 130 000 tonnes per day.The mine is located near the town of Logan Lake, 220 km northeast of Vancouver, British Columbia and 55 km southwest of Kamloops. The map in Figure 1 shows the general area. Kamloops is a major service centre and is served by two railways, two major roads and a regional airport. The mine site is situated between 1200 m and 1600 m above sea level on the Thompson Plateau. Principle activities in the area, in addition to mining, are cattle ranching and forestry. Ore reserves at the beginning of 1996 totaled 533 million tonnes at a grade of 0.42% copper and 0.008% molybdenum. Ore is mined from two pits — Valley, 3 km northwest of the mill; and Lornex, 1 km southwest of the mill. With 78% of the reserves, the Valley pit is the focus of activity.In order for Highland Valley Copper to remain competitive with a very low grade ore reserve, it has been necessary throughout the mine’s life for new technologies to be embraced as they become available. These have included such diverse technologies as in-pit crushing and conveying, large mechanical drive trucks, computerized truck dispatch and oneman survey instruments. During the next few years, it is planned to introduce two further technologies that are relatively new to both the world at large and the mining industry in particular. These are namely Global Positioning Systems (GPS) and Geographical Information Systems (GIS), both of which are expected to have a major impact on the way mining is carried out in the years to come."

Jan 1, 1997

By L. Tikasz

The primary purpose of ore hauling model studies is to capture the variability of the ore delivery ? stockpiling process in order to improve the estimation of equipment capacities and achievable throughputs. The operation of a mine-to-site ore delivery system is the subject of a number of challenges. Typically, ore is hauled by a given combination of trucks, conveyors and trains. In addition, ore loading, ore transferring to another means of delivery, stockpiling, reclaiming, and further deliveries involve many other types of equipment. The concurrent operation of all these units is scheduled; nevertheless, they are subject to planned maintenance and random breakdowns. To support our engineering design work on ore hauling operation, discrete event type models were built for each specific task. Then, due to recurring demands, an ore hauling library was gradually compiled. The now available model library allows fast and efficient simulation of various mine-to-site hauling arrangement, adaptable to various mining and mine construction operations (e.g. bauxite, iron ore, copper ore and coal).

Aug 1, 2013

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015