Search Documents

By H. Tetu, F. Pells

"The copper-molybdenum property of Brenda Mines Limited is located in the Okanagan district of British Columbia, approximately 25 miles west of Kelowna. The Okanagan Valley is a resort and fruit-growing area, and therefore pollution control measures are more stringent than in some remote areas.The Brenda plant began production in April 1970 and is operated at a rate of 24,000 tons per day. The plant site is located at an elevation of 4,800 feet, which is approximately 3,600 feet above the level of Okanagan Lake. The site is in the Okanagan drainage basin.The major consideration in the design of the system was the prohibition of any downstream discharge. It was therefore necessary to redaim as much water as possible and to minimize the addition of fresh water to the system. The maintenance of a water balance is of critical importance.This paper will outline the major design criteria for the systems and the site investigations which were carried out. The design and construction of the facilities will be de-scribed and current operating experience will be outlined."

Jan 1, 1971

By A. P. Sasmito

It is well known that underground miners are exposed to one of the most dangerous working environments on earth. As mine delve deeper, the geological factor, mine position and climate condition as well as heat generation from mining machine give rise to the mine operating temperature. This, in turn, has an adverse effect on the environment and thus leads to higher operating costs. Careful estimation and design of air flow rate, spray system, cooling load and additional ventilation auxiliary equipment are of importance to ensure safety, comfort and productivity whilst maintaining low operating cost. A computational fluid dynamics simulation approach is employed to examine underground mine ventilation in a 36 m cul-de-sac of tunnel of coal mine. The model predictions in the turbulent range were validated by comparison with published data. Different turbulence models were tested to select one that yields adequate accuracy and is computationally efficient. Effects of the following parameters are evaluated: tunnel geometry, air flow rate and inlet air temperature. The objective of the simulation is to arrive at an optimal strategy for ventilation and thermal comfort at low cost.

Aug 1, 2013

By Alfred Guenkel, Kyle Marte, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985 (Borbely, Devuyst, Ettel, Mosoiu & Schitka, 1985). Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. Though it is possible to supply sulphur dioxide (SO2) in either gas or liquid form, the majority of these SO2/air operations use sulphite-based salts as the ‘SO2’ equivalent reducing agent. This is probably due to the lower capital cost, safety concerns with, and availability of liquid SO2. Sodium metabisulphite (SMBS) is commonly employed, and its cost is an order of magnitude higher than that of sulphur. The increased capital expenditures (CAPEX) for a sulphur-burning SO2 gas plant could have a pay-back of less than two years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas inventory. Furthermore, a SO2 gas plant will not trigger the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and Boleo).This paper discusses the different processes which require SO2 as a reducing agent and compares the capital and operational costs of a SO2 gas plant to conventional process alternatives using sulphite-based salts or liquid SO2.The heart of the SO2 gas plant is the sulphur furnace. The most economical way to produce SO2 is by combustion of sulphur in air producing up to 19.5 vol% SO2. Examples of large and small sulphur furnaces are discussed in terms of design, operation, and impacts on operational costs.The SO2 gas produced in a sulphur-burning plant has to be contacted with the liquor to be reduced. The choice of gas-liquid contacting device is important, and two contacting devices are discussed: 1) Gas sparging into the bottom of leach tanks (high, nearly constant, back pressure due to liquid head) and 2) absorption columns (low gas-side pressure drop)."

Jan 1, 2014

By P. D. R. Maltby

This paper describes the background and markets for calcium carbonate and silica sand in Canada, as well as the results of recent test work carried out at the Ontario Research Foundation. Tests on sericite, tremolite, vermiculite, barite and graphite are also mentioned.

Jan 1, 1979

By Frédéric Bélanger, George P. Demopoulos, Pascal Coursol, Thomas Feldmann

"The use of scandium in industrial applications is expected to rise in the coming years, in large part due to the expected adoption of new, clean energy technologies such as solid oxide fuel cells or Sccontaining high strength aluminium alloys. Given that the supply of Sc is currently dominated by only a few countries (Russia and China) other sources for scandium extraction need to be investigated. This paper looks at different options for the recovery of scandium from waste solutions generated during the production of TiO2 pigments via the chloride process route. In particular, a direct solvent extraction (SX) approach and possible options for concentrating scandium before the SX step were investigated. It was found that the presence of Ti during solvent extraction causes severe formation of stable emulsions, which can complicate the successful application. This was particularly a problem after multiple contacts of the organic phase with fresh aqueous phase. On the other hand it was noticed that the presence of certain elements in the solution, e.g., iron, could possibly be utilized to concentrate scandium in a solid precipitate.INTRODUCTIONMany newly developed high-tech products depend on the use of chemical elements that are only produced in very small quantities. This can result in high and fluctuating prices, as can be seen from Figure 1, which may cause substitution with inferior alternatives, if possible at all (Reck & Rotter, 2012; US Dept. of Defense, 2013; Whittaker, 2011). One example is scandium (Sc) a member of the extended rare earth element family. There are only a few scandium ore deposits, but most Sc is produced from the processing of by-products of other metallurgical processes (Melcher & Wilken, 2013). Increasing demand for scandium metal and oxide (Sc2O3, scandia) is coming from its increased use in applications such as ceramic lasers (Li, Ikegami, & Mori, 2005; Rainer et al., 1982), high strength aluminium alloys (Lathabai & Lloyd, 2002) as well as solid oxide fuel cells (SOFC) (Thijssen, 2011). Especially, the spread of climate friendly SOFC’s, which are a commercial product today (Bloom Energy, 2014), is expected to be a main driver for future Sc2O3 demand. However, the rate of market penetration of this green technology depends on the availability of high purity Sc2O3 (>99.999%), since it specifically contributes to longer life-time and better safety of the SOFC’s (Bloom Energy, 2014; Irvine, Politova, & Kruth, 2005)."

Jan 1, 2016

By W. E. Hale

An area of about 7,000 square miles within the eastern part of the Grenville Sub-province is underlain chiefly by granitic gneisses. There are, however, some exposures of mafic rocks which warrant further investigation, and some attractive structures, particularly basins, which deserve additional economic consideration. T HIS paper describes in a very general fashion the economic and geological features of an area of about 7,000 square miles on the north shore of the Gulf of St. Lawrence in the eastern part of the Grenville Sub-province (Figure 1). The scarcity of published geological data on this part of the Cana-dian Shield (DePuyjalon, 1899 and Longley, 1944) justifies the presentation of these tentative results. It should be appreciated, however, that the information which follows was acquired in a rapid reconnaissance designed specifically to out-line what might be interpreted as favourable geological environments for the occurrence of economic minerals, rather than to produce an authoritative analysis of the geological history of the region.

Jan 1, 1962

By R. Bainbridge

THE cinnabar deposits of the Consolidated Mining and Smelting Company's Pinchi Lake property, situated near Fort St. James, B.C., were discovered and reported on by a Dominion Government geological party in 1937. Claims were staked by a group of local prospectors and, later, the Consolidated Mining and Smelting Company of Canada, Limited, took an option on the property. By the fall of 1939, exploration work had indicated ore of commercial quantity and grade, and laboratory tests had shown that standard methods of reduction, namely, roasting of the ore, followed by condensation of the mercury vapour produced, would result in satisfactory recovery. In June, 1940, construction of a 50-ton unit arranged for wood firing was completed and operation commenced. The installation consisted of a 46 in. by 60 ft. rotary kiln (see Figure 1) followed by a 14-in. Sirocco cyclone, a cast-iron condenser unit, and a 1,700 c.f.m. fan, exhausting to a stack. Other equipment included a 9 in. by 18 in. Denver jaw crusher with the necessary bins and feeders. As the need for mercury was urgent, because of war requirements, construction of a duplicate unit was begun almost immediately. This first extension started operation in January, 1941, and the plant was then capable of treating about 150 tons of ore daily.

Jan 1, 1945

By Ernest A. Hodgson

A SERIOUS hazard which must be faced in some mines, though quite absent in others, is that of rockbursts. Bursts cannot be wholly avoided in such mines, but the hazard would largely disappear if they could be predicted. The problem of prediction resolves itself into that of measuring pressure in the mine and determining when that pressure nears a critical value. The geophysical approach to the problem lies in discovering some physical property of the rock, which varies with pressure, which can be measured for rock in place, and for which the indication of critical conditions is sufficiently definite and open scale. A physical property, suggested first in connection with earthquake pre-diction, is that of sub-audible snapping. It was argued that, as the pressure grows, the rock probably yields microscopically and that minute snapping occurs which is so faint as to be inaudible to the unaided ear. Experience has proved this to be the case. Following other earlier work begun early in 1939, experiments with this method were initiated at Lake Shore Mines in 1941, and equipment was slowly being developed in practice when, fortunately, it was found possible to by-pass this tedious development programme. Experiments with sub-audible snapping in mine rocks had been carried out by Dr. L. A. Obert of the U.S. Bureau of Mines and his associates over a period of about four years. An amplifier and a recorder were developed, each reasonably satisfactory in practice. Lake Shore Mines offers a tempting field for rockburst research. Dr. Obert was invited to test his equipment in this and other mines in Ontario and did so. As a result, he and the administrative personnel of the Bureau became interested in the Lake Shore experiments co the extent of most generously arranging for the manufacture of sets of their own designed equipment for use in this programme. The first three sets of recorders were ordered at once and were delivered in May, 1942. A second group of three sets, incorporating various improvements indicated by experience both in the United States and in Canada, reached Kirkland Lake in April, 1943. The pick-up devices, known as geophones, were made in the electronics laboratory at Lake Shore by Mr. Zack Gibbs, who has had charge of all the instrument development in this re-search.

Jan 1, 1943

By J. Grignon, C. Fleming

It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch kinetic tests, coupled with mathematical models that translate kinetic data into predicted steady state gold profiles across multi-stage adsorption circuits. Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the step wise change can be determined. In this way it is possible to inexpensively optimize the operating conditions of an existing plant, with no disruption to plant operations and no economic risk to the mining company. This approach had been adopted by IAMGOLD to optimize the performance of their Rosebel CIL plant following several major expansions in mill capacity since 2004.

Jan 1, 2011

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018

By S. A. R. Keneti

Predicting the geomechanical response of the shale gas material during hydraulic fracturing operation in the field needs better understanding of their geomechanical behaviour under laboratory testing. Anisotropy is considered as a critical factor during investigation and analysis of deviated boreholes, borehole stability, stress-strain and strength behaviour, generation and propagation of fracture and fluid flow. In this study, compressive elastic modulus (Ec) of the Montney shale has been investigated in two perpendicular directions: unconfined compressive strengths test was conducted on the Montney sample to measure its Ec in the vertical direction. This value then was compared to the Ec value in the horizontal plane (i.e. foliation plane) which was previously measured throughout a Brazilian test by Keneti and Wong (2011). From the results, the representative values of Ec in the vertical and in the horizontal directions were found as 25 GPa and 40 GPa, respectively. Computer tomography technique was also employed for the experimental data interpretation.

Jun 1, 2012

By A. A. Ruitenberg, G. Ruitenberg, J. Chandra

"The Caledonian Belt is mainly underlain by Late Precambrian and possibly Early Palaeozoic rocks, which are in part overlain by younger strata. Most of these rocks are weakly deformed, except for those in some linear . zones, which have been intensely deformed by cataclasis. Mineral deposits related to two distinct metallization episodes have been recognized. The earliest are zinccopper- lead sulphide deposits, which have been concentrated in the axial regions of late-stage cross-folds within the main cataclastic zone. The host rocks are andesitic and dacitic tuffs which show effects of intense talcose alteration, silicification and chloritization. Deposits related to the second episode are mainly composed of copper sulphides with locally abundant tennantite and tetrahedrite, which occur in brecciated and fractured carbonate-quartz veins. These veins postdate the late-stage cross-folds. VLF-EM and high-sensitivity magnetics proved to be very effective in delineating the geology of these deposits."

Jan 1, 1972

By G. Forté, R. Girard

The Alcan Bayer Process Experimental Centre (BEC) is an essential development tool for the Bauxite & Alumina researchers at the Alcan Arvida Research and Development Centre in Jonquiere, Quebec. Between the laboratory tests and the industrial prototypes or the industrial applications, the BEC is a key element for technology transfers. The Bayer process is the extraction of aluminium oxide (or alumina) from the bauxite ore. The Bayer Experimental Centre's history and flowsheet are presented. The major pieces of equipment are described. Safety and design considerations are presented. Finally, examples of applications, double digestion and pressure decantation, are briefly described.

Jan 1, 2004

By J. Kan

In order to determine the recovery functions in an oil sand circuit it is necessary to have more than a minimal determination the mass flows in the network. This over-determination is essential in order to allow for measurements within the flow matrix "to flex" according to an error function. It is then possible to identify the flows and composition at all points with maximum likelihood. These so-called full mappings are not easily obtained. However, in order to obtain an unequivocal determination of all the unit operations recoveries such a balance is needed. When databases are constructed exclusively with coherently balanced sets of data it is possible to obtain a maximally accurate process model by maximizing the probability of correctly identifying the process causality. Indeed, it is doubtful in cases of normal complexity that any sense can be made of data that is not so balanced. Coherent mass energy balancing is a tool developed by mineral processing scientists and engineers. Its rigorous application to oil sands is the subject of this paper. The additional element associated with hydrocarbon requires special considerations. It is shown that at least one currently available mineral processing tool will solve the full-mapping problem for an oil sand operation. Experimental design constraints are discussed in this paper relating to the development of databases for the development of effective process models.

May 1, 2004

By M. S. King

"A simple method is proposed for determining the long-term deformation behaviour of evaporites. The theory developed can be tested by measuring the change in diameter as a function of time of a vertical mine shaft opposite evaporite strata. Ultimate shaft closures predicted by the theory agree well with those calculated with the very much more complex theory of Serata (1968), provided that sufficiently high octahedral shear strengths are used in the former.An analysis of measurements made in an isolated opening in a Saskatchewan potash mine shows that the octahedral shear strength of the surrounding potash and halite was approximately 500 psi several years after the opening was mined. This value is less than that deter-mined experimentally for halite by Serata. The same data indicate, furthermore, that the in-situ octahedral shear strength is decreasing slowly with time.The current controversy regarding the actual deformation of evaporites will only be resolved by the cooperation of potash producing companies in releasing data on the long-term deformation of their mine shafts."

Jan 1, 1971

"This paper deals with the reconciliation of open stope performance at Olympic Dam, South Australia, with a focus on stope stability, recovery, and operational aspects of stope reconciliation in relation to the expected or planned stope design. The observed stope performance is inconsistent with the equivalent linear overbreak sloughing criteria for assessing the performance of large open stopes. The aim is to investigate new stope performance criteria using quantitative (overbreak, underbreak, maximum depth of wall failure) and qualitative (stope productivity, observed fragmentation) information that correlates with the observed stope behaviour, providing a process for improving future stope designs.RÉSUMÉ Le présent article traite de la réconciliation de la performance des chambres ouvertes à Olympic Dam, Australie du Sud, en ciblant la stabilité des chambres, la récupération et les aspects opérationnels de la réconciliation des chambres par rapport à la conception attendue ou planifiée des chambres. La performance observée des chambres ne concorde pas avec les critères d’épaisseur équivalente du bris hors profil pour évaluer la performance de grandes chambres ouvertes. L’objectif est d’étudier de nouveaux critères de performance des chambres au moyen de données quantitatives (rupture hors profil, rupture à l’intérieur du profil planifié, profondeur maximale d’effondrement du mur) et qualitatives (productivité de la chambre, fragmentation observée) qui concordent avec le comportement observé des chambres, fournissant ainsi un processus pour améliorer les futures conceptions des chambres."

Jan 1, 2015

By Sarah Bélair, Denis Beltrami, Valérie Weigel

"Mabounié is a polymetallic deposit in Gabon containing niobium (1.2%), tantalum (0.03%), rare earth elements (REE) (1.4%) and uranium (0.03%) that are mostly carried by Pyrochlore minerals. Classical route for niobium recovery is a pyrometallurgical process that consists in pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF.ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore. After solubilisation of the valuable elements, niobium / tantalum are precipitated as a concentrate (12% w/w Nb and 0.3% w/w Ta) while REE (2.7 g L-1) and uranium (90 mg L-1) remain in solution. Nearly 90% of REE are recovered from the solution by conventional REE double salt precipitation [NaREE(SO4)2.xH2O) method but some REE still remain in solution as this method does not allow to quantitatively recover medium (Sm, Eu, Gd, Tb, Dy) and heavy (Ho, Er, Tm, Yb, Lu, Y) rare earth elements. From the different process routes studied (solvent extraction, precipitation, ionic exchange etc.), an innovative method has been developed and patented to recover REE residual concentration in solution. This is based on an aluminum removal step followed by precipitation of REE as REE phosphate concentrate (REEPO4) by phosphate addition into solution. The phosphate concentrate is then purified according to the conventional monazite treatment, i.e. caustic conversion and REE solubilisation in acidic media."

Jan 1, 2016

By A. Saigal

A finite element analysis based investigation using DEFORM software was undertaken to model the extrusion of 15% alumina and 15% silicon carbide reinforced aluminum metal matrix composites. The study dealt with predicting the extrusion load as a function of ram displacement and initial billet temperature. The finite element simulation was also used to determine the maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions in the billet during the hot extrusion process. The constitutive equation used was of the type: Z = E exp(Q RT) = A{sinh(ao-)}" where Z is the Zener-Hollman parameter (temperature compensated strain rate), s is the strain rate, Q is the activation energy, R is the gas constant, T is the absolute temperature, a is the flow stress and A, a and n are constants. Based on the work of Davies et al and McQueen and Konopleva, the values of Q (KJ/mol), a (MPa-1), n and A for aluminum 6061 composites reinforced with 15% alumina and 15% silicon carbide used are 181, 0.024, 4.15 and 1.33x10'2 and 233, 0.052, 2.60 and 1.26xl0'4, respectively. Even though the individual parameters are quite different, it was found that the predicted maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions are quite similar and differ by no more than 1-2 percent between the two composites indicating that the deformation behavior is primarily controlled by the matrix material and is not a function of the type of reinforcing ceramic particulates.

Jan 1, 2004

By David Sanscartier, Elizaveta Petelina, Alexey Klyashtorin

This paper provides an overview of the radiological risk mitigation approach applied by the Saskatchewan Research Council (SRC) for the remediation of 35 legacy uranium mine sites in northern Saskatchewan where uranium exploration and extraction took place in the 1950–60s. Mining activities resulted in an irregular increase of the gamma radiation dose rate (up to 18 μSv/h). The radiological objectives for the sites include a gamma dose rate at a spot (<2.5 μSv/h above local background), and the dose rate averaged over a hectare (<1 μSv/h above local background). These objectives are generally achievable at the impacted sites through the installation of shielding soil cover. This method may be impractical for site areas with rough terrain (e.g., steep slopes) and/or difficult access. A risk assessment approach is applied to determine if these areas can be safely left uncovered or if additional mitigation measures should be implemented. The risk assessment approach is based on two factors: (i) the ambient radiation dose rates collected through gamma surveys, and (ii) actual land use data collected through various surveys of activities of local community members at the sites. Exposure scenarios based on four land uses are applied to estimate a potential annual dose load for members of the public. The estimated doses are compared with the criterion of 0.3 mSv/a recommended by the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). If the criteria are not satisfied, a mitigation plan is developed, and post-remediation gamma levels are modelled using GIS tools to evaluate the performance of the proposed mitigations. The proposed approach allows the team to optimize resources for the site remediation so that public exposure to NORM are as low as reasonably achievable after remediation.

Jan 1, 2020

By D. Tao

Froth flotation is widely used in the coal industry to clean -28 mesh or -100 mesh fine coal. A successful recovery of particles by flotation depends on efficient particle-bubble collision and attachment with minimal subsequent particle detachment from bubble. Flotation is effective in a narrow size range outside which the flotation efficiency drops sharply. A fundamental analysis has shown that use of picobubbles can significantly improve the flotation recovery of particles by increasing the probability of collision and attachment and reducing the probability of detachment. A specially designed column with a picobubble generator has been developed for enhanced recovery of fine coal particles. Picobubbles were produced based on the hydrodynamic cavitation principle. Experimental results with one metallurgical coal and one steam coal have shown that the use of picobubbles in a 2" column flotation increased fine coal recovery by 10-30%, depending on the feed rate, collector dosage, and other flotation conditions. Picobubbles also acted as a secondary collector and reduced the collector dosage by one third to one half.

Jan 1, 2006