Search Documents

By R. L. Bailey

"The Acheson D-3 Pool was discovered in August 1950, and contains 88 producing oil wells on 40 acre spacing. Initial oil-in-place was 118 million stock tank barrels and initial well potentials averaged 2,000 barrels per day.In early 1956 studies of hydraulic interference between the Acheson and Leduc D-3 Pools were conducted on the Carter Petroleum Reservoir Analyzer. These studies indicated that the natural water drive to Acheson would be incapable of replacing reasonable withdrawal rates over the life of the pool. To avoid shrinkage losses a scheme of pressure maintenance by water• injection was therefore instituted in March 1957.This pressure maintenance scheme is notable because pressure is being effectively maintained by high volume injection through one well located on the flank of the pool. Close control on reservoir behaviour is maintained by regular bottom-hole pres-sure surveys and observation of water cuts on producing wells. No evidence of pressure gradients or channelling of the injected water has been observed to date, and the water-oil contact has remained level over the whole field. It is possible to control the average reservoir pressure within very close limits by varying the rate of fresh water injection.Ultimate recovery estimated from the rise of the oil-water contact and calculated water influx to December 31, 1958, is 335 barrels per acre foot, or a total of 91.4 million barrels from the pool. This compares to 217 barrels Per acre foot or a total of 59.4 million barrels indicated from laboratory test data."

Jan 1, 1961

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By K. Shen, A. J. Sinclair, N. Champigny

"Fluid inclusion studies from the Cinola deposit indicate low salinities and low C01 contents of the ore fluid. This supports a suggestion that the mineralizing fluids originated from pore water in the fluviatile host rock (mid-Miocene Skonun Formation). Bimodal distribution of filling temperatures suggests the existence of at least two temperature regimes centred on 160°C and 270°C during mineral deposition. Independent age and stratigraphic evidence indicates that depth of mineralization is between 1.1 and 1. 8 km, corresponding to a hydrostatic load of between 110 and 170 bars.RESUMELes donnees sur les inclusions fluides du gisement Cinola indiquent de basses salinites et basses teneurs en C01 . Ceci confirme que les fluides mineralisants ont ete derives de l'eau interstitielle prise dans les sedimentsfluviatiles hates. La distribution bimodale des temperatures d'homogenisation implique !'existence de deux regimes de temperature concentrees vers 160°C et 270°C pendant Ia mineralisation. La profondeur alaquelle le gisement s'est forme est evaluee d'etre entre 1.1 et 1.8 km a partir d'informations stratigraphiques independantes: ceci correspond a des pressions hydrostatiques de 110 a 170 bars."

Jan 1, 1982

By Dean L. Millar

Measures taken by mining companies around the world to reduce their carbon footprints are becoming increasingly important in the sector securing its social licence to operate. The options for measures reduce to three categories of activity: i) demand reduction by avoiding unnecessary waste of supplied energy, ii) improving the utilization of energy that does have to be consumed and iii) adopting low carbon energy production options?including renewable energy. As well as the environmental imperative, as the prices of electricity, gas and liquid fuels increase, so the economic case for activities i) to iii) gains higher priority, especially in such an energy intensive industry. The specific energy consumption for certain upstream minerals industry operations in Canada is reported to be as follows: underground mining: 99.5 kWh/tonne mined; surface mining: 11.7 kWh/tonne mined; base metal processing: 81.4 kWh/tonne milled; gold processing: 99.6 kWh/tonne milled. Around 508 kWh/tonne (slag) of heat is reported to be available in cooling slag from 1500°C to 25°C; an amount that is simply indicative of the energy intensity of downstream smelting and refining operations. Low carbon, energy saving technology options that are available to mining industry companies lead to projects with return rates that must compete alongside other capital intensive projects considered by mining company boards. Energy projects frequently involve longer payback periods and lower rates of return than those of competing bids for capital, such as those for development of new mineral properties. For energy services companies (ESCOs) that specialize in the financing, construction, and the efficient operation and maintenance of energy projects, the same returns and payback periods may be considered acceptable or even attractive. For the ESCO, the key commercial risk mitigating factor is a securing a long term contract for the supply of energy.

May 1, 2011

By Pingchao Ke, Zhihong Liu

"To overcome the problem that scoroditeis not stable in neutral and alkaline solutions, we proposed and investigated a synthesis method of scorodite coated in-situ with hydrated ferric oxide in the Fe(II)-As(V)-H2O system at the initial Fe(III)/As(V) molar ratios larger than 1.0.The synthesis was carried out at 90?,pH 1.5 under atmospheric pressure. During the synthesis, oxygen gas was conducted and bubbled into the system to oxidize Fe(II) ions into Fe(III)ions, and Na2CO3aqueous solution as neutralizing agent was added controllably into the system for keeping the pH constant at 1.5. In this study, three samples of scorodite were synthesized at the controlled initial Fe(II)/As(V) molar ratios of 1.0, 2.0 and 3.0, respectively. The characterizations of the samples by HRTEM, TEM/EDX, and chemical composition indicated that the particle surfaces of scorodite synthesized at the initial Fe(II)/As(V) molar ratio of 2.0 and 3.0 were coated in situ by a film of hydrated ferric oxide with the thickness of several nanometers, while the sample synthesized at the initial Fe(II)/As(V) molar ratio of 1.0 was uncoated scorodite. The TCLP and long-term leaching for the toxicity characteristic of the samples showed that scorodite coated in situ with hydrated ferric oxide was stable in a wide pH range from 3.0 to 10.0, with the arsenic concentrations in the leaching solutions less than 1.0mg/L. Nevertheless, uncoated scorodite was unstable under the conditions from weak acidity to alkalinity, with the arsenic concentrations in the leaching solutions larger than 5.0 mg/L.INTRODUCTIONArsenic pollution is a challenge for environment and health and has been an important issue for scientists (Hopkin, 1989).Arsenicis commonly associated with ores or concentrates of nonferrous metals, mainly as independent arsenic bearing minerals such as arsenopyrite (FeAsS), tennantite(Cu12As4S13), enargite (Cu3AsS4), cobaltite (CoAsS), and gersdorffite (NiAsS), realgar (As2S2), orpiment(As2S3), etc.(Matschullat, 2000; Mandal & Suzuki, 2002; Long & Peng, 2012). In the nonferrous metallurgical processes, arsenic is enriched mainly in such arsenic bearing materials as various flue dusts, residues, and anode slimes, which results in the accumulation of arsenic in the system owing to the circulation of those arsenic-bearing materials back to the system and the pollution to the environment (Harris, et al, 2003).In addition, the utilization of arsenic is limited and has been decreasing owing to its toxicity and carcinogenicity. Therefore, arsenic has to be removed from those arsenic-bearing materials and discarded safely (Dutrizac & Jambor, 1988; Monhemius & Swash, 1999; Drahota & Fillippi, 2009).In this case, how to immobilize arsenic has become a difficult problem which must be solved. Among the methods of immobilizing arsenic which have been proposed and investigated, immobilizing arsenic into a stable mineral to fix it, has been realized as a promising method and becomes a research focus(Dutrizac et al, 1987; Dutrizac & Jambor, 1988; Demopoulos et al, 1995; Fujita et al, 2008a; 2008b).Scorodite has been known as one of the best minerals for immobilizing arsenic, owing to its high stability under weak acidic condition, the arsenic content as high as 32wt%,and good crystallinity benefiting the separation of solid to liquid(Daivid et al, 1999; Zhu & Merkel, 2001). Scorodite can be synthesized from arsenic containing solutions under both hydrothermal and atmospheric conditions, and a lot of work has been done on the synthesis of scorodite and its leaching stability characterization (Filippou & Demopoulos, 1999; Gomez et al, 2011).Two plants for the immobilization of arsenic as scorodite have been putin to operation in Chile and Japan, respectively (Filippou & Demopoulos, 1999; Amir et al, 2016)."

Jan 1, 2017

By C. McLachlan, J. R. Donald

"Positioned at the forefront of the seafloor minerals industry, DeepGreen Resources is on track to becoming a leading producer of base and strategic metals obtained from vast high-grade seafloor polymetallic nodule deposits. DeepGreen believes the seafloor minerals industry is an opportunity for developing a more environmentally and societally attractive way to produce cleaner base and strategic metals. Polymetallic nodules contain nickel, manganese, copper, cobalt and other base and strategic metals. Polymetallic nodules represent an exceptional multi-metal-bearing resource, and no current metallurgical operation or flowsheet exists that can recover the primary metallic values while managing the distinct mineralogy. DeepGreen Resources is developing a new process to maximize the business outcomes consistent with the highest environmental standards, including targeting a near zero waste facility. The present paper discusses the history, context and driving forces of polymetallic nodule project development. An overview of DeepGreen?s Nauru Ocean Resources Inc. (NORI) project is presented along with a literature review of polymetallic nodule processing and the on-shore project development scope and plan at DeepGreen Resources is outlined.INTRODUCTION AND CONTEXT Polymetallic Nodules in the Clarion-Clipperton Zone Containing nickel, cobalt, copper and manganese, polymetallic nodules occur in most oceans of the world. The nodules lie on the seafloor sediment. The largest deposit in terms of nodule abundance and metal concentration occurs in the Clarion-Clipperton Zone (CCZ) on vast abyssal plains at a depth of 4,000 to 6,000 metres. The CCZ is located almost entirely in international waters as presented in Figure 1. It has been estimated that the CCZ contains (International Seabed Authority, 2010): •,>21 billion tonnes of nodules; •,>270 million tonnes of nickel; •,>6 billion tonnes of manganese; •,>234 million tonnes of copper; •,>46 million tonnes of cobalt. There are several active hypotheses for the mechanism of formation of the nodules including precipitation, hydrothermal decomposition of basaltic debris, and involvement of microorganisms. Nodules require a nucleus to start forming, which could be a piece of pumice, a shark tooth, old nodule piece, basalt debris or even microfossils like radiolaria and foraminifera. Nodules form concentrically with layers of iron and manganese hydroxides around a core. Although composed mainly of Mn, Fe, silicates and hydroxides, it is the significant content of Ni, Cu, Co, Zn and Rare Earth Elements (REE) that is generating the economic interest in harvesting these deposits. Nodules vary in size from micro-nodules to about 20 cm, the common size being two to eight centimeters. A typical polymetallic nodule and polished cross-section is presented in Figure 2."

Jan 1, 2017

By X. Zhou

"Hydrogen induced failure and degradation in structural metals, namely hydrogen embrittlement, has been a long-standing industrial problem for more than one century and remains unsolved. Despite the proposal of numerous models, no consensus has been reached, and considerable discrepancies in experimental observations and theoretical calculations exist. One aspect that is central to the understanding of hydrogen embrittlement is the interaction between hydrogen and grain boundaries. In this study, we investigated the influence of several solute elements (i.e., Cr, Mo and Nb) on hydrogen segregation at the representative 9 grain boundary using first-principles calculations. Our results showed that the presence of Mo and Nb can reduce the tendency of hydrogen segregation at grain boundaries, while meanwhile enhance the grain boundary strength. This indicates that Mo and Nb are salutary elements that can be used to increase the material’s resistance to hydrogen embrittlement, providing new insights in designing hydrogen embrittlement resistant Ni alloys. INTRODUCTION Hydrogen embrittlement (HE), a phenomenon of hydrogen triggering premature failures in structural metals, has been a headache for industries ever since its first discovery one century ago (Johnson, 1874; Zhou, Marchand, McDowell, Zhu, & Song, 2016; Zhou, Ouyang, Curtin, & Song, 2016). It is well accepted that the segregation of hydrogen at microstructures such as grain boundaries (GBs) plays a key role in determining the occurrence and severity of HE. GBs are two-dimensional defects where significant local lattice distortion exist, which leads to large free volume and thus locations for hydrogen trapping and segregation. Numerous works have clarified GBs as the energetically preferable places for hydrogen segregation. For instance, Geng et al. demonstrated the preferential segregation of hydrogen at the S5(120) GB in several metals, and suggested a decohesion-type of HE in light of Rice-Wang thermodynamic theory (Geng, Freeman, & Olson, 2001). Birnbaum et al. illustrated that complete intergranular crack of Ni GBs can be induced by hydrogen segregation when the hydrogen concentration is sufficiently high, evidencing the significant role of hydrogen accumulation on GB weakening (Lassila & Birnbaum, 1987). Yamaguchi et al. demonstrated strong segregation hydrogen also occurs at S3 GBs in alpha-iron, showing that local hydrogen clustering (i.e., multiple hydrogen atoms, up to six, per unit cell) can be trapped at the S3 GB (Yamaguchi, Kameda, Ebihara, Itakura, & Kaburaki, 2012)."

Jan 1, 2017

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada's Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988

By Dawei Yu, Kinnor Chattopadhyay

In the nickel industry, molten slags produced from a Pierce-Smith converter contain significant amounts of valuable metals in the forms of oxides and physically entrained matte droplets. A slag cleaning step, which takes places in an electrical slag-cleaning furnace, is therefore required to recover the valuable metals as a common practice. Utilization of a waste material from aluminum industry (i.e. spent potlining) as a flux to improve the slag cleaning in terms of both the metal recovery and the operation efficiency was studied by simulation with FactSage program. Results show that the addition of SPL could substantially reduce the slag viscosity due to its fluoride values, thus accelerating the settling of matte droplets. The carbon value in the SPL could also help increase the metal recovery by reducing the valuable metal oxides followed by settling.

Jan 1, 2015

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

Oct 1, 2010

By Q. Han

A modified cast-on method has been developed to reinforce aluminum castings with steel insert. Defect-free bond between the steel insert and the aluminum casting has been consistently obtained. Data obtained from a push-out experiment indicated that the bond strength was much higher than that obtained using the Al-Fin approach. This paper introduces this modified method in four sections: the coating of the steel pins, the cast-in method, microstructure characterization, and the bond strength. The section on the coating of the steel pins contains coating material selection, electro-plating technique for plating Cu and Ni on steel, and diffusion bonding of the coatings to the steel. The section on cast-in method deals with factors that affecting the quality of the metallurgical bond between the coated steel and the aluminum castings. The results of microstructure characteristics of the bonding are presented in the microstructure characterization section. A push-out experiment and the results obtained using this method is described in the section of bond strength/mechanical property.

Jan 1, 2015

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

The New Zealand opportunity NZ?s only significant phosphate deposit 1 million tonnes imported annually - mostly from Morocco US $180/t + $75/t freight

May 1, 2013

By D. J. Robertson

"THE copper smelting operation of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, generates a gas flow of 350,000 c.f.m. at n.t.p. This gas stream passes to atmosphere through a 20-foot diameter by 250-foot brick stack, carrying with it an appreciable dust burden in the form of metallic oxide fumes. The flow constituents during the period 1952 and 1953 and •before gas filtration was included in the treatment scheme are shown in Table I. This paper describes the gas filtration treatment which was installed in 1957, using glass cloth media to recover this dust burden, and discusses the associated problem as its treatment for recovery of zinc and cadmium.The metallurgical details associated with the problem are illustrated by a description of the material flow sequence of the Company's hydrometallurgical zinc plant and copper smelter. In this ore processing complex, the zinc plant and copper smelter form an integrated unit within which intermediate zincrich products of each operation enter the treatment circuit of the other."

Jan 1, 1960

By R. Q. Honaker

It has been shown that naturally hydrophobic carbonaceous materials such as coal and graphite can be selectively coagulated and separated from hydrophilic impurities without using oily agglomerants, flocculants or electrolytes. The coagulation occurs at C-potentials significantly higher than those predicted by the classical DLVO theory, suggesting that it is driven by the hydrophobic interaction. In the present work, the energy barriers for the coagulation of a hydrophobic coal sample have been calculated using the extended DLVO theory which incorporates the hydrophobic interaction energy in addition to the dispersion and the electrostatic energies. For the coagulation of minerals present in the coal, the classical DLVO theory has been used for the energy barrier calculation. The results of these calculations provide an excellent correlation with the results of a series of Selective Hydrophobic Coagulation (SHC) tests conducted with run-of-mine coal and graphite samples.

Jan 1, 2004

By Wenxue Chen

This paper presents a new type of bolt with full thread and uniform strength, and fabricated with a Glass Fiber Reinforced Polymer (GFRP) bolt-making machine designed by the authors. The mechanical performance of the new bolt is assessed with strength tests conducted with the bolt in acid, alkaline and saline water conditions, with increasing concentration. The purpose is to test the new GFRP bolt?s mechanical performance in harsh conditions, especially metal mines with acid or alkaline environments. Comparison of the color, weight, size and antistatic ability of the GFRP bolt before and after it is immersion in solution is presented. Changes in tensile and shear strength, torsion, and anchoring force were evaluated in the laboratory. The results show that the mechanical properties of the GFRP bolt are more sensitive in alkaline than in acid and saline water. However, the loss ratio of mechanical properties of the GFRP bolt is very small according to the results of tensile and shear strength, torsion and anchoring force. The new bolt can be useful for applications in acid or other harsh mines.

Aug 1, 2013

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952