Search Documents

By R. L. Alexander

"Madawaska Mines Limited, incorporated in 1975 is the successor to Faraday Uranium Mines Limited. The history of the latter's mine development and corporate changes are outlined. This paper describes the geology of the Bancroft area and the rock types found in the mine, particularly the pegmatite which is the host rock for the uranium. The structure, mineralogy and distribution of the ore shoots are described with the method of grade control and mine development. The paper concludes with a summary of the production and mineral reserves.Location, Access, and PropertyMadawaska Mines Limited is located in Faraday Township, Hastings County, Ontario. The mine is in the N.T.S. quadrant 31 F/ 4, Bancroft sheet and near 46 degrees 01 minute latitude, 77 degrees 46 minutes longitude. The mine is one-half mile north of Highway 28, five miles (8 km) west of Bancroft, and is accessible by various highways from Toronto, Ottawa, Peterborough, and Belleville. (Fig. 1). A landing strip for small aircraft is located at the northwestern edge of Bancroft. Bancroft is a modern community with a population of 2,400. The company has the mineral rights to 2982 acres (1207 hectares) surrounding the mine workings and plant which are situated in the north parts of Lots 16 and 17, Concession XI, Faraday Township."

Jan 1, 1986

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015

By A. Glover

As the demand for natural gas as a prime global energy source continues to grow, the search for new sources of the fuel spreads into geographical areas that are more remote from the marketplace. Along with this comes the need for longer and ever more efficient pipelines. This requirement for higher value in natural gas transportation is satisfied to a large extent through the application of high strength technology and innovative design approaches that support increased design and operating pressures. This paper reviews the latest accomplishments and successes in these technologies for use in gas transmission. It also explores some of the technologies which are targeted for the future to allow the industry to achieve even higher benchmarks in reliability and cost-effectiveness. The central element in the theme of high strength technology for gas pipelines is that of high strength steel. From tensile strengths of Grade 359 a few decades ago, more and more operators are now specifying Grade 550 linepipe for their large diameter projects. As well, Grade 690 steel is operating successfully in limited transmission applications and Grade 825 has recently been installed. With the introduction of the latest high strength pipe comes the need for high strength fittings. The industry's first Grade 550 fittings were recently specified and installed on a project with Grade 825 line pipe. High strength materials can only be implemented successfully if compatible design and construction processes are in place. The latest developments in strain- and reliability based design will be described as well as the corresponding advancements in welding and inspection technology.

Jan 1, 2005

By Nicola Robjohns, Kenneth A. Grace, Jane Spooner

"The important volume end use sectors for the rare earth elements and yttrium continue to be in steelmaking, petroleum cracking catalysts and glass polishing. The market sectors which may provide future high volume demand, to replace the older sectors where demand has declined over the past decade, include magnets, automobile catalysts, ceramics and superconductors. Increases in production capacity in all major rare earth producing countries are expected to restrain large price increases for high purity rare earth oxides over the short term. A sharp increase in demand for yttrium in advanced ceramics and superconductors would lead to a shortage in separation capacity, however, and to a corresponding rise in prices for separated rare earths.IntroductionWhile visiting the Geology Department of the University of Toronto in 1981, Professor Lu from the Institute of Geochemistry of Academia Sinica at Gweiyang in China introduced one of his seminars with the observation that in China, rare earths are not rare at all.Indeed, while being rare in terms of abundance as measured by, say, the Clarke scale, the rare earth elements, like many other low abundance elements, are subject to geological, geochemical and mineralogical concentration.The rare earth elements comprise the fifteen inner transition elements of Group IIIB, Period 6, of the periodic table, from lanthanum to lutetium (the lanthanides), as set out in Table 1. The rare earths constitute a distinct group as they have extremely similar chemical characteristics due to the uniformity of their outer electron shells. The element yttrium is usually, by convention, included in the rare earth group as it occurs with the rare earths in nature and has properties very similar to them.The rare earths are divided into two subgroups, the ""light"" rare earths, made up of the first seven elements of the series, lanthanum to europium, and the ""heavy"" rare earths, comprising the remaining eight elements, gadolinium to lutetium, plus yttrium. These two subgroups are also referred to as the cerium subgroup and the yttrium subgroup, respectively. The subdivision is based on differences in the atomic radii resulting in somewhat different properties for the two subgroups."

Jan 1, 1991

By Jarret Thomson

An understanding of groundwater flow is essential for many aspects of mining. This is especially true for the process of shaft sinking through the sandstones of the Manitou Falls Group in the Athabasca Basin of northern Saskatchewan. Experience has shown that the hydraulic conductivities of these sandstones can be relatively high, especially in zones containing natural fractures. To develop a better understanding of the inflow potential into a shaft, a laboratory testing program was undertaken to investigate the hydraulic conductivity of fracture core samples from the Manitou Falls Group. This program involved the measurement of hydraulic conductivities under steady-state flow conditions, while cycling the effective confining pressure across a span that is representative of in-situ conditions. The change in fracture aperture was simultaneously recorded at each confining stress level. It was found that existing relationships relating aperture and flow did not accurately capture the behavior of the samples tested. The effects of fracture staining and infilling were also investigated, and were found to have a notable impact on the hydraulic conductivity.

Jun 1, 2012

By J. R. Morris

"A hoisting plant design should satisfy two basic requirements:1. to provide the necessary materials handling capacity, including ventilation where applicable, while meeting the requirements of good practice and, as a minimum, government regulation; and2. to optimize the economics of the project. Selection of hoisting equipment to meet the first objective is a complex but logical engineering process. The necessary calculations of payloads, accelerations, speeds, rope strength, hoist size, and power requirements are very readily carried out on computers or programmable calculators. A variety of hoist options can be quickly examined to assess the effects of changes in design parameters.Meeting the second requirement involves balancing the costs of various hoist arrangements and shaft designs, together with the time cost effects of differing shaft sinking rates and potential advances to be gained by concurrent level development. The proposed mine layout is significant here, as is the possibility of future shaft deepening and/or production increase. The availability of used equipment may be significant, both as regards first cost and delivery time. The factors are interactive, with their relative effects .varying from project to project. This paper sets out the primary factors to be considered."

Jan 1, 1990

By D. Karpoff

"IntroductionUNTIL the recent discovery and development of deposits at Allard Lake, on the Lower Romaine river, practically the whole of Quebec's - and indeed of Canada's - production of ilmenite had come from deposits in the vicinity of St. Urbain, Charlevoix •county, a village about eight miles north of Bay St. Paul on the north shore of the St. Lawrence, some sixty miles below the city of Quebec (see Figure l) . Although these deposits were known nearly three hundred years ago and were worked in a small way during the years 1872-74, when a charcoal blast furnace was operated by the Canadian Titanic Iron Company for making white pig iron, it was not until 1908 that more or less continuous production commenced and has •continued to the present by the American Titanic Iron Company. The whole of the output has been exported to the United States.The ilmenite occurs in lenses •and dyke-like bodies within anorthosite. Production has come chiefly from three deposits: General Electric, Furnace, and East and West Coulombe. During 1951 -52, an extensive diamond drilling programme was carded out under the direction of the writer to test the Furnace and the East and West Coulombe deposits (Figures 2 and 3), which form part of the property of St. Lawrence Iron and Titanium Mines, Limited. The average tenor of the orebodies encountered in the course of the drilling was 38.60 per cent TiO2 and, in addition to these high-grade •bodies, there was found a very considerable tonnage of lower grade ore."

Jan 1, 1953

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By B. Ignasiak

Laboratory studies suggest that improvements of coke strength brought about by pre-heating caking coals before carbonization accrue from inadvertent oxidation rather than from other low-temperature changes in the coal mass. Controlled oxidation of highly caking coal, followed by laboratory carbonization, produces cokes which, in terms of a laboratory scale tumble test index, are equivalent to those obtained from prime metallurgical blends. Appropriately formulated blends of exhaustively oxidized and fresh caking coal similarly yield cokes with strength indices comparable to those of cokes made from the same coal after oxidation under optimum conditions.

Jan 1, 1979

By H. P. Pew

THE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by T HE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by 85 miles wide, is the largest in Canada in areal extent, in the amount of oil in place and in the current producing rate. The discovery well was completed in the middle of 1953. The field has grown until its present area is 369,820 acres. There are 74 working interest owners in the field. Early in the producing history of the Pembina field a committee of operators was formed on a permanent basis. The Pembina Operators' Committee has established a permanent staff, which compiles and distributes pertinent field information on a regular basis to all participants. The Alberta Oil and Gas Conservation Board has dealt with field-wide problems primarily through this committee. Expansion of the field was rapid as shown by the number of wells completed -from 135

Jan 1, 1961

By Marcin Ziemski

This paper reports on an energy efficiency analysis completed as part of a research project looking at energy reduction opportunities in minerals processing operations. The plant discussed is a gold production facility owned by Newmont Gold in the Tanami region of central Australia. Due to its remote location, lack of nearby gas pipeline or power grid, the operation has been completely dependent on diesel fuel for its electricity generation and transport needs. The mine and processing plant use electrical power at a rate of 12MW to 18MW, resulting in a monthly electricity cost of over US$1.5M. The high cost of diesel combined with an impending power generation capacity shortage drove Newmont to undertake the energy efficiency study. An energy audit of the plant showed opportunities for significant energy savings through the strategic use of waste heat, fuel replacement alternatives and renewable energy sources.

May 1, 2007

By A. Ignatow

"A review is made of some of the principal factors and conditions that are, and will be, important to the over-all market climate for asbestos fibre and for the future of Canada's asbestos industry: - health hazard associated with asbestos exposure;- uncertain international regulatory environment for continued asbestos use;- adverse public reaction to asbestos;- product liability/litigation costs (U.S.A. primarily);- promotion of substitution by governments and asbestos user industries; and- minimal product and market development efforts by asbestos producing and consuming industries.In addition, Canadian producers, who export some 95 per cent of their production, face additional constraints:- dramatically reduced integration with asbestos-consuming industries;- 60 per cent of exports to most rapidly declining markets (U.S.A., Europe);- increased competition from offshore producers favourably located to growth markets in developing countries;- increasing production costs;- a strong dollar;- disadvantageous freight rates; and- loss of price leadership and price erosion.Future market trends, as well as prospects for Canada's asbestos industry, will be projected in this paper.Economic FactorsTable 1 presents asbestos fibre production in all countries for the period 1980-82. In certain instances, e.g. U.S.S.R. and China, these are capacity estimates as production statistics are not officially published. The U.S.S.R, by far, is the world's largest producer accounting for some 50 per cent of world production, though most production is consumed internally or by COMECON countries. It is estimated that some 700 plants produce asbestos-containing products within the U.S.S.R.Canada accounts for some 25 per cent of world production though it ranks first in world trade. Other important producers are South Africa Zimbabwe, Brazil and Italy. Since 1979, Canada's asbestos mining industry has experienced a dramatic drop in production and exports of asbestos fibre, as demonstrated in Table 2."

Jan 1, 1985

By Rick Valenta

Is the Labrador Central Mineral Belt part of the IOCGU Club? ?I sent the club a wire stating, PLEASE ACCEPT MY RESIGNATION. I DON'T WANT TO BELONG TO ANY CLUB THAT WILL ACCEPT ME AS A MEMBER.? GrouchoMarx Acknowledgements ?Ian Dunlop, Matt Lennox-King, Mark O?Dea, Dave Barbour, Derek Wilton, Lucas Marshall, Roland Butler, Mark King, Sally Howson,

May 1, 2006

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By J. W. Spyker, D. H. Filson, W. H. W. Husband

"Large deposits of sodium sulphate exist in southern Saskatchewan in the brines or muddy crystal beds of alkali Jakes. Currently, more than 300,000 tons per year of sodium sulphate are produced from these lakes and sold as salt cake to the paper industry. Most of the production is obtained from the brines of a limited number of Jakes.The Saskatchewan Research Council was requested to develop a process for recovering sodium sulphate from the muddy crystal beds so that this type of deposit could be exploited in the future. A flowsheet was developed with the aid of phase diagram data and the process was studied on a pilot-plant scale using raw material from three different lakes. Satisfactory yields and product purities were obtained in all cases, and an economic analysis indicated that a 100,000-ton-per-year sodium sulphate plant could produce salt cake at a cost of $12.26 per ton for a rate of return upon investment of 16 per cent at current market prices."

Jan 1, 1966

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By C. R. Stelck

"AbstractThe Cardium formation of northeastern British •Columbia •contains an erosional unconformity that becomes progressively more severe northward until, •at Liard river, the stratigraphic hiatus eliminates the underlying Lower •Cardium sandstone, the Kaskapau formation, and the upper Dunvegan sandstones. The area of unconformity roughly coincides with the distribution of the continental facies of the earlier Dunvegan formation. Along Wapiti river, the zone fossil Scaphites ventricosus Meek and Hayden is found in the Bad-heart member of the overlying Wapiabi shale; Scaphites :preventricosus. Cobban marks the base of the Wapiabi shale; Scaphites cf. corvensis •Cobban is found in the middle shale member of the •Cardium formation. The log of the Red-Willow No. 1 well shows close similarity to the outcrop sections south of Wapiti river. The Cardium formation is mainly late Turonian in age. Two other pre-Cardium Turonian sands of north-eastern British Columbia are named the Wartenbe and Tuskoola sands.IntroductionTHE Upper Cretaceous Cardium (Bighorn) sandstone formation of the Foothills of northeastern British Columbia carries within its formational limits an erosional unconformity. The unconformity decreases to the southeast, becoming in immediate shoreline regions, now under the plains, a minor diastem. Such diastems, or stratigraphic intervals of non-deposition, occurring in the shallow unda-zone are paralleled in the deeper portions of the unda-zone by the phenomena of sub-aqueous winnowing. '.This winnowing and re-working •at critical depths creates sand areas with porosity."

Jan 1, 1955

By W. F. Giuvlore, E. Mcroberts, T. S. Golosinski

"The rising demand for Canadian coal and depletion of shallow deposits, most suitable for surface mining, result in rapidly increasing volume of waste materials which have to be moved by the coal mining industry. While at present this challenge is being successfully met using conventional mining methods, in the future, innovative methods must be considered if Canadian coal is to remain competitive.The need for more efficient mining methods is also faced by the oil sands industry to assure competitiveness of the synthetic oil price.A look at the world mining practice indicates that large volumes of material can be economically mined and moved by the continuous mining systems comprising bucket-wheel excavators, belt conveyors and stackers. To assess the state of art and applicability of this mining method to Canadian conditions, the field trip was organized by the Department of Mining Engineering o f the University of Alberta, to several typical mining operations in Europe. It is in Europe where the continuous mining methods were developed and are almost exclusively used in large-scale surface mining."

Jan 1, 1984

By R. E. Legg

This paper gives a brief outline of the mining and milling methods which will be used on the Stirling zinc-lead-copper ores by Stirling Mines, Limited, who have for the past two years been developing the Stirling mine in Richmond county, Nova Scotia, and who will bring the mine into production in November, 1929. No attempt has been made to give the paper a detailed technical character, for the main reason chat, since base-metal mining is something new in Nova Scotia, it is felt that a general description would be preferable before this Society, whose membership is mainly made up of chose engaged in the coal mining and associated industries. Furthermore, as both mining and milling operations will be governed to a certain degree by the experience gained after production commences, there are many points which cannot be definitely stated now. GEOLOGY Before discussing the mining methods, it is desirable to present a general picture of the geology and occurrence of the ore-bodies. The surface rocks in the vicinity of the mine consist of rhyolites of .pre-Cambrian age. These volcanic flows outcrop in very few places, usually along&apos; the beds of creeks or on the shores of the numerous small lakes. Consequently, a detailed geological map is not available. The exploration work carried out to date has revealed a sheared zone extending through the volcanic flows for a distance of over 1,000 feet. Along this zone, there has been a replacement of the rhyolites by a carbonate rock for widths varying from 50 to 230 feet, and it is in this carbonate formation chat the mineralization at a later date took place.

Jan 1, 1929

By Marc Arpin

La Bolivie possède tout pour réussir. Son vaste territoire de plus d&apos;un million de km2 et qui occupe une position stratégique au coeur du continent sud-américain recèle des ressources naturelles (forêts, minéraux, gaz naturel, etc) variées et abondantes. Elle a une frontière avec pas moins de 5 pays dont le géant que constitue le Brésil ainsi qu&apos;avec l&apos;Argentine, l&apos;autre puissance régionale. Pourtant, malgré tous ces atouts, la Bolivie demeure l&apos;un des pays les plus pauvres du continent. Ce paradoxe n&apos;est nulle part mieux reflété que dans le secteur minier. Celui-ci fait face à une situation de crise en dépit d&apos;une tradition minière de plus de quatre siècles et d&apos;un potentiel géologique indiscutable ayant conduit à la découverte et à l&apos;exploitation de fabuleux gisements d&apos;argent et d&apos;étain. Les habitants des districts miniers vivent dans des conditions de pauvreté extrême et les indicateurs de développement humain de ces régions sont parmi les plus bas en Amérique du Sud. La Bolivie réussit difficilement à attirer les compagnies minières alors que, chez les voisins, et particulièrement en Argentine, qui n&apos;a pas de tradition minière, les investissements miniers majeurs affluent. Dans cette conférence, nous chercherons à expliquer les causes de cette situation et proposerons des solutions possibles.

May 1, 2001