Search Documents

By Bern Klein

Motivation for Improved Energy Efficiency in Mining ? Canada potentially adopting Greenhouse Gas Emissions and Intensity Legislation in 2013 ? BC -Climate Action Plan and Energy Conservation Agreement in 2008 ? BC Energy Plan 2007 -BC Hydro is mandated to save 50% of new load growth ? TSM Initiative -Energy Management, Energy Reporting, Setting Energy Targets, GHG Management BC MOU for Energy Conservation Agreement -MEMPR, MABC, BC Hydro

May 1, 2010

By A. Y. Senchenko, Y. V. Kulikov

"Different methods aiming at specific energy calculation and design of AG/SAG circuits are used in mining. They include JK DWT/SMC test, SAGDesign test and CWi/RWi/BWi tests. The simplest methods with no secret equations and giving energy required for grinding in kWh/t were proposed by F.?. Bond and J.H. Starkey. D.J. Barratt proposed to use results of CWi/RWi/BWi tests for AG/SAG mill sizing. The present paper gives an alternative for forecast of specific AG/SAG energy. The principle is similar to the theory proposed earlier and consists in cumulative AG/SAG energy calculation using indices of rod and ball grinding (RWi+BWi) without impact crushing index (CWi). Then total energy is divided between two grinding stages using special formulas based on extensive statistical information. The forecast indices of AG/SAG and ball grinding are similar to the SAGDesign testing results. Hereinafter the predicted indices are used for mill sizing of the whole grinding circuit. The method considered in the paper enables prediction of AG/SAG energy based on the test results according to Bond method. The proposed method version was not widely published earlier. The aim of the work was to elaborate cost-effective, reliable and accessible way to determine specific AG/SAG energy. At this stage of method development, it is recommended to use it only for works at preliminary Geometallurgy stage (Scoping, Pre-Feasibility). At design stage the obtained data should be confirmed by appropriate testing using alternative JK DWT/SMC and SAGDesign methods.INTRODUCTIONAppropriate crushing and grinding testing is required to design efficient comminution circuits. It is obviously important to obtain accurate information about ore hardness properties since the main energy consumption at the plant is associated with comminution processes. Moreover, it is required to apply the processes that make it possible to minimize operating costs and efficiently use capacity of the installed equipment installed.When studying ore hardness properties, it is required to take into account that breakage of the material is performed using different equipment. That is why accurate selection of the equipment and the circuit calculation without relevant testworks is impossible. Ideally, the testworks should provide answers to the following questions: determination of ore hardness properties, determination of specific energy consumption for comminution as well as obtaining of sufficient amount of statistically significant results from the tests. The results from crushability and grindability testworks in the first place provide assessment of ore hardness properties and in addition correlate with throughput of the respective equipment. The data obtained can be used for modeling of comminution circuits at the stage of the technology development"

Jan 1, 2016

By Kenji Koga

In order to derive the population distribution of gold nanoparticle morphologies as a function of size, highresolution electron microscopic (HREM) observations and structural analyses were done for over 4000 particles (3-18 nm) grown by an inert gas aggregation (IGA) source using helium. To obtain structural features threedimensionally and not to skip high-contrast images, twenty photos were taken for each particle by changing tilting angle of a specimen holder in combination with the through-focus procedure. For the reliable structural determinations, HREM images and their tilting sequences were directly compared with multislice-simulation results for icosahedral, decahedral and face-centered cubic morphologies, and finally the population distribution of each morphology was obtained as a function of size. In the present sample, icosahedral particles were dominantly populated over the whole observed size range and decahedral particles with non-spherical truncated bi-pyramid shape were secondly dominant. Even though a large number of sampling has been done, few crystalline particles were observed.

Oct 1, 2003

By J. A. Vallejos

Re-entry protocols are a tactical approach for controlling risk after blasts or large events in seismically active mines. Based on the results of a survey on 18 seismically active mines, mostly in Ontario, current re-entry practices are summarized. Over half of the mines in Ontario use event decay rate analysis as their primary re-entry decision making parameter. We study in detail the applicability of the Omori?s law as an equation for describing the event decay rate for more than 250 mining-induced aftershock sequences in seven different environments. Practical guidelines for the use of the Omori equation as a re-entry criterion are proposed.

May 1, 2009

By L. R. Plitt, A. J. Neale, B. C. Flintoff

"INTRODUCTIONThis is not a technical paper in the normal sense. It is an informal document which is intended to share the results of some recent cyclone research with our colleagues both in operations and in research.PILOT PLANT FACILITIESFigure 1 is a schematic of the closed circuit hydrocyclone pilot plant testing facility at the University of Alberta. In this figure the system is configured for some experimental work on wide angle cyclones which was recently completed. The rig is designed to study cyclones in the approximate range of 10 cm to 20 cm diameter. Notable features include the variable speed feed pump, the magnetic flowmeter and pressure sensors on the cyclone feed line and the travelling launder which permits simultaneous sampling of both product streams.ORGANIZATIONFor organizational convenience the subject matter has been divided into three parts:(1) Peculiar Partition Curves(2) Wide Angle Cyclones(3) Rope DischargePECULIAR PARTITION CURVESMuch of the initial empirical mathematical modelling work on cyclone classifiers dealt with homogeneous ores. A homogeneous ore is one in which all particles have substantially the same apparent density, or where one phase is very clearly predominant. In contrast, a heterogeneous ore is one in which there are at least two different density classes, each making a significant contribution to the ore composition. (Particle shape similarity is always assumed.)One of the problems which can arise when analysing the overall solids partition (selectivity, Tromp, etc ... ) curve for a heterogeneous ore is the peculiar shape which may be observed, when compared to partition curves for homogeneous ores. This is not an unusual occurrence and it has been documented by Lynch and Rao, Finch and Laplante and Larsen and Spring. The purpose of this section is to identify those operating conditions which may give rise to peculiar partition curves."

Jan 1, 1986

By Denis Thibodeau

his paper describes a study of an altered mining extraction and the resulting Rockmass response at VALE?s Creighton Mine. Typically, the deep mining zones have strict stope extraction guidelines to ensure safety and productivity; however, these guidelines offer low flexibility or few options for stope sequencing. The 402 O. B. being in a good rock mass, at moderate depth and stress regime at Creighton, offered an opportunity to drive a more flexible mining sequence with stopes and a pillar. A three-phased approach was used to mitigate risk of the mining plan: 1- Numerical modelling to fully anticipate rock mass response to the proposed mining sequences. 2- In situ seismic monitoring to collect stress and seismic activity data. 3- Analysis of the in situ data to correlate to the modelling results. The creation and the extraction of a pillar in the 402 O. B. was successfully completed. The recorded seismic activity agrees well with the numerical modelling since most of the seismic activity is localised in the hangingwall where the deviatoric stress corresponds to an early damage process. The moderate levels of deviatoric stress cause localised failure with low level of seismic activity.

May 1, 2013

By Emilie S. Williams

The Doyon Mine?s Zone 1 (Altered Zone), found along the southern boundary of the mine, encompasses approximately 20% of the mining reserves. The mineralisation is found in a series of steeply dipping narrow veinlets, which are contained in an extremely weak host rock: a sericitic schist with RQD values ranging from 0 to 20. Longhole mining methods are used, with either longitudinal or transverse approaches, depending on the width of the ore zone. Dilution is of critical importance in the mining of this zone, particularly in longitudinal stopes, where dilution levels have averaged 55% since 2000. Major factors influencing dilution in this zone include the stope geometry and standup time. A two-phase approach has been developed to mine and backfill longitudinal stopes: the top of the stope is pastefilled after approximately half of the broken ore has been extracted; the remainder of the ore is extracted once the plug has cured; and the remaining void is filled. This method has been used in six stopes to date, resulting in an average dilution of 17%. This paper details the application of this technique and its effect on dilution.

Oct 1, 2004

By Ralph Johnson, Philippe Gaultier, Loui Fauteux, Andrew Dasys

"This paper outlines the implementation of the Mechanic's Stethoscope from the earliest stages of development to the implementation at Brunswick Mining and Smelting. It details the cooperative efforts of personnel at Noranda Technology Centre (NTC) and Brunswick Mining & Smelting (BMS) during the technology transfer of the Mechanic's Stethoscope. It demonstrates how everyone worked toward a goal of developing a product that is accepted as a useful addition to the work environment.The Mechanic's Stethoscope is an underground vehicle diagnostic system consisting of computer hardware and software intended to assist mechanics in daily tasks. Its tools facilitate quick and easy access to any information required during the maintenance of an underground vehicle. Each tool presents vehicle condition data in a simplified manner. The additional information improves the mechanics understanding of the vehicle condition. The result is a healthier fleet of vehicles and faster diagnosis times.When introducing a computer based system into a traditionally non-computer oriented environment a concern is the acceptance of the system. This concern exists on many levels."

Jan 1, 1995

By W. E. Armstrong

Gypsum was first exploited as ?a commercial proposition in this province by the Union Mining Company which, in 1900 opened quarries on the east shore of Lake Manitoba, near the present site of Gypsumville. This company established a mill at the head of Portage Bay on the lake, and the manufactured plaster was carried by the companies boats to McArthur's siding on the Whitemouth river near Westbourne, Man., from which point it was distributed. In 1904 a reorganization took place and the Manitoba Gypsum Company Limited bought out the original company, and operated the original mill for about one year when it was destroyed by fire. There were many factors which rendered the operation of a mill at the quarries very difficult; lack of rail transportation for bringing in supplies, and the impossibility of local power development made manufacturing costs very high. Satisfactory distribution could not be affected because of water transportation and poor terminal facilities at McArthur's siding. For these reasons the new mill was built at Winnipeg, where cheaper power and better distributing facilities permitted the industry being placed in a better position. The company continued to bring the gypsum rock by steamer to Totogan, from which point it was transported by rail to Winnipeg. This period was one of steady expansion as the product became better known and more universally accepted as a wall finishing material. Unfortunately, in 1909, this new mill was destroyed by fire, causing a serious set-back to the company, at a time when the steady growth of the western market gave every promise of the industry being placed on a profitable basis.

Jan 1, 1925

By P. N. Saavedra, E. A. Salamanca

"The maintenance strategies in the mining industry are changing from operative and periodic inspection strategies to a condition-based, predictive maintenance strategy centred in vibration analysis plus complementary techniques. Condition monitoring can also help to improve availability by being able to pinpoint and diagnose problems on operating machinery at an early stage. This reduces unscheduled downtime and production losses.However, in mining, for shovels operating in transient modes, with variable load and/or speed, the FFT (Fast Fourier Transform) standard approach is not directly applicable for analysis. This work illustrates how spectral order analysis and new transforms, called time-frequency transforms (TFT), allow us to monitor the shovel when it is working. Some practical examples showing the application of these analysis techniques to occasional vibrations measured on hoist and crowd transmission of a shovel are also presented. It is shown that at present, it is possible to carry out the vibration monitoring in the mining shovel while it is working, therefore avoiding the high cost of a loss of production which can occurr in traditional monitoring, where the measurement is taken while the shovel is out of production."

Jan 1, 2002

By A. Ouchi

This paper presents ground control best practices in weak rock environments including the "Unsupported" Weak Rock Updated Span Design Curve and awareness pertaining to the potentially detrimental effects of using resin grouted rebar in weak rock masses and the false sense of security that the use of resin grouted rebar may instill. Ground support is almost always used in weak rock environments, though the type of support used can vary widely. The development of the Weak Rock Updated Span Design Curve by the addition of 463 case histories of RMR76 values ranging from 25 to 60, has also been calibrated to four different support categories; Category A: Pattern Friction Sets, Category B: Pattern Friction Sets with Spot Bolting of Rebar, Category C: Pattern Friction Sets with Pattern Rebar Bolts and Category D: Cablebolting, Shotcrete, Spiling, Timber Sets or Underhand Cut and Fill. Design of underground man-entry type excavations in North America relies heavily upon empirical analysis. This design requires a higher Factor of Safety than other non-man entry type excavations. A comparison of the calculated ½ span failure Factor of Safety between all the categories is also presented.

May 1, 2009

By J. Lapointe, S. Leger, D. Proulx

"Une méthode non-électrolytique est utilisée pour plaquer au cuivre la fibre d'amiante chrysotite. En variant les paramètres de placage du bain, on détermine les conditions optimales du taux de deposition du cuivre . Une analyse par diffraction aux rayons-X permet une comp araison relative des résultats de placage et de précipitation d'oxyde cuivreux dans Ie bain. Le traitement de placage a pour but d'assurer une adhésion suffisante de la fibre dans une matrice métallique Iors de la fabrication éventuelle de materiaux composites.IntroductionCette communication se veut un compte-rendu de nos travaux sur Ie placage au cuivre de la fibre d'amiante chrysotile, en vue de I'incorporer éventuellernent dans une matrice métallique. La fibre d'amiante est constituée de fib rilles élementaires d'un diamètre d'environ 0.02 um qui ont une résistance en tension de I'ordre de celie de la fibre de verre ou de carbone(1). Pour être efficace, la fibre de renf'ort d'un matériau composite doit d'une part, avo ir des propriétés mécaniques intrinsèques élevées, et d'autre part, adhérer solidement â la matrice pour que Ie transfert de charge s'effectue sans qu'il y ait décohésion entre les composantes du matériau.La fibre d'amiante étant naturellement soyeuse, il faut la traiter superficiellement pour que l'adhésion avec la matrice soit suffisante. Ainsi, on recouvre la fibre de phénol-formaldéhyde(2) ou de silane(3) lorsqu'elle est employée avec une matrice polymere. Dans Ie cas d'une matrice métallique, ces dépôts organiques ne peuvent resister aux températures de mise en oeuvre, d'où l'intérêt de plaquer les fibres par un dépôt métallique.Dans cette étude, nous rapportons les résultats relatifs à la methode utilisée pour plaquer au cuivre la fibre d'amiante chrysotile. Une analyse par diffraction aux rayons-X permet de comparer les différentes conditions de placage non-électrolytique."

Jan 1, 1985

By Jacques Deraisme

The technology of percussion drilling is well mastered. The lower cost of percussion drilling allows more holes to be drilled for the same budget. However significant differences are often observed between percussion and diamond drill assay data. This is due to the increased level of contamination associated with the percussion drilling process. Statistical studies on twinned drillholes show that diamond and percussion assays cannot simply be merged in a traditional kriging approach. The question then arises on how to use both types of data to produce reliable resource estimates. To take into account the lower reliability of the percussion assays, a noise characterized by a variance is added to these data. The methodology consists of two steps: 1. Cokriging of the equivalent diamond value at the percussion assay locations. 2. Block kriging using diamond assays and equivalent diamond values, calculated previously, adding to these data a noise, whose variance is the cokriging variance of step 1. This particular way of achieving kriging is called kriging with variance of measurement error. The paper illustrates this innovative methodology with an application on an iron deposit. The results of this method is compared to block kriging using only diamond assays and the gain in precision is quantified. An extension of that approach to multi-element cokriging is also presented.

Oct 1, 2009

By S. Espley, G. Tan

"Inco's Little Stobie Mine is a low-grade nickel operation producing approximately 4()()() tons per day. Backfill has never been an economical option at the mine; therefore, the only viable type of mining in the upper zones has been by sub-level cave. This mining method allows for the draw-down of a rock cover into the empty stopes to provide stability to the over-all rock mass. In the lower areas of the mine, bulk blasthole mining methods have taken place, without rock fill, resulting in extremely large open stopes. As the mine reaches its final stage of recovery, it is inevitable that the hangingwall of the large voids will undergo tensile failure via spoiling.This paper deals with the collaborating efforts of Inco's Rock Mechanics group and the Little Stobie mining operations toward the successful recovery of the ore zone remnants such that the inevitable failure, and time of failure, of the rock mass is ""controlled"". Within the mining scheme, several key requirements had to be met to satisfy the operations: (1) production rates; (2) good blast fragmentation; and (3) secure pulling-horizons. A full-scale rock mechanics study was carried out involving: numerical modelling studies; pulling ellipse analyses; blast design, monitoring and analyses; laser profiling; and time domain rej7ectometry (TDR) instrumentation. The final recovery scheme, employing a controlled failure, involves recommendations on: (1) blasting techniques; (2) support systems; (3) mining sequences and scenarios; and (4) monitoring systems."

Jan 1, 1994

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texas Gulf Incorporated operates the Kidd Creek Mine, a 10,000 tons per day base metal producer, near Timmins, Ontario. Two different ore types are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall Concentrator the ores are processed by selective flotation in threes individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream x-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8%, zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.INTRODUCTIONSEcstall Mining Limited, a wholly owned subsidiary of the Texas Gulf Incorporated operates the Kidd Creek Mine, one of the world's major base metal producers, near the old gold mining centre of Timmins, Ontario. Discovered in 1964, the property was brought into production in November, 1966. Originally designed for 9,000 tons per day, the operation now treats 10,000 tons per day of two different ore types mined from a single open pit. In the near future, open pit ore will be supplemented by ore from an underground operation now being readied for productionAt the Ecstall Concentrator the ores are processed by selective flotation in three individual circuits. The whole plant is highly automated and control is coordinated from a central control room. The treatment process follows conventional practices although fine grinding is required for optimum flotation recoveries. Normally, two circuits treat copper-zinc ore at a combined rate of 6,500 tons per day while the third circuit treats 3,500 tons per day of silver-lead-zinc ore. Special production averages 2,400 tons per day."

Jan 1, 1973

By W. J. Dick

THE purpose of this paper is to point out, briefly, the importance of the coal mining industry of Alberta and to stress the economic factors that hinder its development; also to offer suggestions relating to the major problems of the industry. The minor problems will not be dealt with in detail, because, if the major problems are taken care of, it is felt that the industry itself can take care of ,he remainder. COAL MINING NO LESS IMPORTANT THAN GOLO MINING The large increase in metal mining development in all provinces of Canada, excepting Saskatchewan, Alberta, and the Maritimes, has had the effect of focussing public attention on this branch of the industry. The fact, also, that this development came at a time of depression has been of immense benefit to Canada as a whole. On account of the necessity and consequent demand for gold, with its attendant increase in price, through government action, from $20.67 per ounce to $35.00 per ounce, it is safe to say that the public of Canada have become, today, gold mining conscious. While everyone admits the great value. of the gold mrn111g industry, nevertheless, the equal value to Canada of certain other industries must not be lost sight of. The coal mining industry, in particular, is worthy of greater public and government support than has been accorded it in the past. It would seem unnecessary to stress this matter to a meeting of the Canadian Institute of Mining and Metallurgy, but unless certain facts are brought to your attention, there is danger that the coal mining industry will not be developed to the extent its national importance deserves. Too many public men and men in authority are unaware of the value of coal mining.

Jan 1, 1936

By W. A. Lang

Introduction That the coal industry has entered a new phase in its development is now evident. Coal, besides being the chief source of heat and power, has become a potential raw material for many industries. Rapid progress has been made in the methods used in the mining and preparation of coal, and in the equipment for the burning of coal. Data of a fundamental nature relating to the composition of coal and to its transformations? during combustion and processing have also been revealed. Research, the key which has opened this new era, has already accomplished much, but it has only begun to show what it may and should be able to do. New developments of coal burning equipment, super-power plants, carbonizing and briquetting plants, hydrogenation and synthetic chemical processes, will undoubtedly have a marked influence in the post-war years on the economic welfare of many coal producing countries. Until comparatively recently, however, there has been in many branches of the coal industry a tendency to regard research as something abstruse and something which had little or no value to those managing such branches. But the fact that coal has suffered as a source of heat and energy through inroads of oil, natural gas, and water power, has made it plain to the industry that, if it is to maintain its present markets in this competitive world, much less increase them, the whole industry must be willing to follow the example of other industries and plan for the future.

Jan 1, 1946

By C. R. Edwards

"Equity Silver Mines Limited, Canada's largest silver mine, has designed, built and operated a leach plant to reduce the levels of antimony and arsenic in its silver-gold-copper flotation concentrate. The orebody contained deleterious antimony and arsenic minerals in such proportions that the economic long-term sales contracts necessary to obtain project financing could not be procured. Construction of the leach plant therefore allowed development of the mine to proceed. Although the plant took some time to reach design throughput and product specifications, due to the complex and unique nature of the operation, these goals were successfully met and surpassed. This paper describes the physical plant and/or process technology modifications made to mold the main processes-concentrate leaching and filtering, autoclaving and filtration of by-products, and crystallization of salt cake-into an effective, economic operation.IntroductionEquity Silver Mines Limited, a member of the Placer Development Group, owns and operates an open-pit silver mine and related facilities located 37 kilometres southeast of Houston in north-central British Columbia. The mine occupies a 44 I-hectare (1089 acre) site at an elevation of 1300 metres (4265 feet) on the Nechako Plateau. Producing a copper concentrate containing high values of silver and gold, it is the largest silver mine in Canada and one of the largest in the western world. Equity stresses open communications, positive motivation, and production with safety, and achieved the best mine safety record in western Canada in 1984."

Jan 1, 1985

By K. Wood, R. McIvor, P. Blythe, M. Lavallee

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented.Total mill x Classification x Test specific x Grinding power draw system efficiency grinding rate rate ratio= Production rate of new product size materialExamples from industrial plants and applications in the research and development field are discussed.

Jan 1, 1990