Search Documents

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

By S. Stefanizzi

In the present paper, numerical simulations based on a finite/discrete element approach are used to study deformation and failure process during standard rock mechanics. FEM/DEM modeling has been used as available with the ELFEN code, which explicitly model the transition from continuum to discontinuum. The transition is simulated through a crack nucleation and propagation that obeys to the Griffith?s failure criterion. If the fracture criterion within the intact rock (represented by FEM) is met, a new crack (represented by DEM) is initiated. Remeshing allows the fracture process through the FEM mesh to be tracked and visualized, thus contact properties can be assigned to pre-existing fractures and newly generated fractures. In this study, compressive tests of rock samples are simulated. The applicability of ELFEN to properly and efficiently simulate typical laboratory rock mechanics tests, with reference to the rock fracture process, is described in detail. In addition, an indirect validation of the extensional strain criterion proposed by Stacey (1981) is given.

May 1, 2009

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015

By Richard C. Banting

Excessive vibration is known to have an adverse affect on soft body tissue and operators of heavy mining equipment can be exposed to vibration that exceeds levels recommended in international guidelines (ISO 2631-1, for example). Research has found that many of the seat and suspension systems currently used in mine haul trucks and load haul dump vehicles are actually amplifying the vibration. This overview presentation will outline the current research being conducted at Laurentian University and the University of Western Ontario, and the roles of partners in rating the ability of a number of commonly used mine vehicle seats to isolate harmful vibration.

Oct 1, 2010

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

This paper details a brief history of the Australian gold industry from the 1980s gold boom to the present day, highlighting an industry characterised by innovation in plant design and junior companies prepared to "have a go", in contrast to the conservatism of many larger mining companies. Design flexibility, the innovation of new processes, the preparedness to exchange "process know how" and technology singularly differentiated the gold industry from other sectors during the 1980s to the present. The introduction of two stage crushing, semi autogenous (SAG) milling, and pebble crushing, mill innovations, carbon in pulp (CIP) and carbon in leach (CIL) and the North Kalgoorlie screen etc were all exciting changes in the industry.

Jan 1, 2011

By B. K. Gorain, A. W. Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimization of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimization, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterize cell hydrodynamics, gas dispersion properties, froth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimization of the Red Dog flotation circuit. IntroductionThe traditional methodology for flotation scale-up and plant design is based on the ruleof- thumb with safety factors and dimensionless hydrodynamic group similitude considerations. With the recent trend toward larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-ofthumb and trial-and-error, the probability of failure would then increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimization of the circuit to meet its metallurgical target. This results in a plant design, which may be incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2003

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By A. Desbiens, A. Pomerleau

During the summer of 1994, a new PID-based control strategy was installed on line B of the grinding circuit at the Kidd Creek Division of Falconbridge Ltd. Part I of this paper described the methodology used to select the appropriate control strategy using a phenomenological dynamic simulator. Part II presents the implementation of the control strategy. Prior to the controller installation, it was necessary to solve various problems related to the process, such as a cyclic behaviour of the rod mill feed tonnage, a problem related to the mill water source and the calibration of the flowmeters. Once these problems were solved, the control strategy was accomplished in two steps. Step 1 corresponds to the installation of control loops to regulate the pump box level and the cyclone overflow density. Step 2 describes the implementation of a loop to control the cyclone feed density. According to Part I, a loop to control the circulating load is also part of the original design. However, reasons are given to explain the rejection of this loop. For both steps, technical procedures such as filtering, process identification and controller tuning are detailed. Finally, the operator’s interface is briefly described.

Jan 1, 1997

By Andy Cole

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual-alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

May 1, 2002

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By Trevor Harris, Martin Harris

"This paper evaluates the effect of grind size on the flotation performance of a platinum ore from the UG2 reef of the Bushveld Igneous Complex, in South Africa. The study was conducted on the Mintek Flotation Pilot Plant Facility, located in Johannesburg, and represented a thorough evaluation of the application of the flotation modelling methodology developed jointly by the University of Cape Town and the Julius Kruttschnitt Mineral Research Centre at the University of Queensland through the AMIRA P9 Project. A simulation model of the pilot plant data was successfully implemented, providing a set of circuit modelling parameters that appeared to be both consistent and well correlated to measurable characteristics of the ore and the pilot circuit operating conditions. The findings indicate that the methodology that was used could well provide a useful framework for developing optimisation criteria for industrial flotation circuits in combination with appropriate feed grind size and regrind size targets.INTRODUCTIONIt has long been recognised that the size distribution of an ore is one of the most important factors in the determination of the performance of a flotation process. It therefore follows that the optimisation of a flotation plant cannot be considered without due recognition of the interdependence of this process with the process of comminution. There are numerous qualitative guidelines for the selection of an optimum grind target for a particular operation. Mineralogical analysis can readily provide information on liberation as a function of grind, and the desirable particle size range for optimum mineral flotation is well established in both theory and practice (see for example Trahar, 198 1). For some operations, meeting these two criteria simultaneously is relatively simple. For the majority of operations, such mineralogically “easy” deposits, if they ever existed, have long been exhausted, and the optimum grind represents a highly complex compromise between liberation and overgrinding of both desirable minerals and gangue. This is particularly true for circuits that include regrind stages, where both primary and secondary (and sometime even tertiary) grind targets must be specified. As has been pointed out in a recent paper by Bazin and Hodouin (2001), there is little or no information in the literature to assist plant engineers in the selection of optimum grind targets for complex ore deposits, so current practice is primarily based on rules-of-thumb and experience. This problem is further compounded by the fact that once grind targets have been selected for a particular operation, the assessment and adjustment of these targets based on plant surveys is extremely difficult, time consuming and expensive, and is often not attempted unless the plant significantly underperforms relative to expectation. It is therefore clear that the development of a practical quantitative approach to this problem is a high priority for flotation research and development studies."

Jan 1, 2002

By W. L. Murphy

The Star Lake property, located 115 km northeast of La Ronge, Saskatchewan is underlain by metamorphosed andesitic tuffs and flows which have been intruded by the dioritic to granitic Star Lake Pluton. Gold mineralization on the Star Lake property was first discovered at Ru h Lake by E. Beveridge in 1959 and by M. and E. Hird in 1961. In 1960 E. Partridge discovered Kahn 18 and Kahn 28. In 1982 the SMDC-Starrex joint venture completed geophysical and geochemical urveys including magnetics, VLF, IP/Resistivity, vegetation, bulk till and oil sampling, followed by drill testing of pecific targets. To date the most ignificant depo it is the 21 Zone which contain drill indicated reserves of 230,000 tons grading 0.5 oz/ton Au . The 21 Zone con ists of quartz with 5-10% (locally > 30%) drusy pyrite, minor chalcopyrite and trace amounts of scheelite, chalcocite and arsenopyrite. The 21 Zone is enclosed by a 25-50 m wide band of mylonitized monzonite. The mylonite occurs in the central portion of a 300 m wide northeasterly trending zone of brittle deformation .

Jan 1, 1986

By William M. Luff

This paper outlines the regional geology and history of the area, and summarizes the stratigraphy, structure and geology of the Brunswick No. 12 mine area. The Brunswick No. 12 deposit is a stratiform massive sulphide body. It occurs in rocks of the Tetagouche Group, which is believed to range in age from Lower to Middle Ordovician. The stratigraphic sequence, including the stratiform orebody, in ascending order consists of older metasedimentary rocks, augen schist, metasediments, augen. schist, footwall metasediments, the -massive sulphide body, iron formation, hanging-wall metasediments, siliceous tuff, basic volcanic rocks , basic iron formation and a porphyry dyke. This sequence is similar to that at some other deposits in the area. Four phases of structural deformation are known to be present in the Brunswick No. 12 mine area. The first deformation folds (F1 ) and associated faulting are the most important factors in determining the distribution of the massive sulphides. This deformation has resulted in the massive sulphides being separated into four zones: the Main Zone, the West Zone, the East Zone and the V-2 Zone. Brunswick Mining and Smelting Corporation Limited is actively mining, developing and exploring the deposit.

Jan 1, 1977

By G. C. Mackenzie

At the last Annual Meeting of the Institute, Dr. C. V. Corless sketched the potential mineral wealth of Canada so clearly, graphically and with-all so entertainingly that one's imagination was fired with the promise held out to future generations for the tremendous expansion of the mining industry in the Dominion. Posterity will undoubtedly witness the fruit of much of the geographical search and survey that is now carried on by our government mining departments. Year after year the work advances, slowly but surely, new areas are . explored, older areas are surveyed in detail, the information being compiled in maps and reports of incalculable value to the prospector, the engineer and the general public. The immensity of the task of exploring, geologically, the outlying portions of the country, with the ultimate view of making valuable mineral discoveries, may be visualized from a study of Dr. Corless' paper and the subsequent discussion which took place and one becomes impressed with the fact that three-quarters or more of the problem can be included under the word "transportation". For instance Dr. Corless said, "The few geological explorers who have penetrated to these remoter regions . . . . . . have as a rule been compelled to stick closely to canoe routes,"; Dr. Goodwin remarked, "This barren Laurentian granite, which is put down on the maps as covering the greater part of this area, is the best guess the geologist could make from travelling along watercourses Within the next few years . . . . . . the Timiskaming and Northern Ontario railway will undoubtedly be extended to James Bay . . . . . . In order that we may be prepared for the probable influx of prospectors when transportation facilities to tidewater are provided, I think all available information on this district should be gathered together in handy form." All three-Corless, Goodwin and Cole-emphasize the well-known fact that explorers, geologists and prospectors working in new country must stick to the watercourses and that transportation by rail, road or water has always been the all-important deciding factor in facilitating the exploration and development of remote districts. Dr. Corless did, however, suggest other means of transportation in stating, "The aeroplane will be of assistance in future study of some parts of these remote areas."

Jan 1, 1924

Material scheduling, sequencing planning and execution are the core tactical mine plan for achieving production targets that maximize the objective function of any mine production entity. This objective function is constrained by several exogenous and endogenous constraints including geological, operating, technological, marketing, financial, political, social and local field constraints. Linear and dynamic programming techniques have been used to formulate algorithms to solve the problems associated with scheduling and sequencing operations. These algorithms possess the mathematical rigor for dealing with the fundamental problems but they fail to provide adequate answers to random and dynamic process problems. Materials scheduling and sequencing are carried out within the bounds of random and dynamic fields. The functional relations between the output and dependent variables are random, and thus, current algorithms are limited in their abilities to address the problems arising from these random field processes. In this study a production simulator is developed to capture the random field process associated with materials scheduling and sequencing in an open pit environment. The algorithm incorporates a geometric pit evolution model, using solid geometry of an ellipsoidal frustum to capture material displacement dynamics. Taylor series expansion about the dimensions of the initial frustum is used to provide numerical solutions to the resulting partial differential equations governing the pushback dynamics. A production simulator, derived from the stochastic and dynamic models, is developed, validated and used to simulate the changes in the pit volume resulting from periodic incremental pushbacks and the random field process. The hybrid stochastic-optimization algorithm provides a powerful tool for addressing the random field and dynamic process problems. Combined with a hybrid stochastic-optimization dispatch system, tactical production planning and execution will be efficient and economic for achieving desired.

May 1, 2004

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By Nicholas C. Williams

This paper presents the development of a demand reduction and responsive strategy capable of reducing the electrical power demand, particularly during peak conditions. The work presented includes a case study of a UK colliery. Areas explained are the equipment installation at the mine; the development of the demand reduction strategy including the load profile database and prediction optimisation model. Some live production data from the power meter installation at the mine is also presented.

Aug 1, 2013

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004