Search Documents

By R G Warren

Sparse geochronological data have been combined with data on felsic suites and depositional facies of rocks to provide an overview of the development of the Arunta Block. The study provides a basis for construction of a map showing the distribution of granites and associated felsic extrusive rocks in the Anmta Block. The tectonic evolution can be subdivided into a series of significant time intervals. Only in the initial stage, to about 1880 Ma, was there any subduction-related magmatism. All later felsic magmas were crustal-derived melts. The early, pre-1880 Ma arc-related units in the SE contain small showings of Cu, probably including the small Cu deposit in the Casey Bore Inlier at the edge of the Simpson Desert. The most significant time-interval for formation of mineral deposits was 1820-1760 Ma, when volcanogenic Cu-Pb-Zn deposits formed in the Strangways Metamorphic Complex and also in the Jervois district. Stratabound tungsten lodes in the hanging wall of

Jan 1, 1994

Low-grade manganese ore from Sandur, India containing 28.2 per cent manganese and 20.9 per cent iron was roasted with sulphating agents, viz ammonium sulphate and sulphuric acid. The effects of temperature of roasting (300 - 800°C), time (15 - 120 minutes) and amount of sulphating agent (0.5 to 2.5 times stoichiometric amount) were studied. Under optimum conditions, it was possible to extract 92 per cent manganese with 0.5 per cent iron at a temperature of 700°C for 90 minutes duration with stoichiometric ammonium sulphate. Further increase in quantity of ammonium sulphate has marginal effect on manganese extraction.Similar studies were carried out with sulphuric acid, and an extraction of about 87 per cent manganese with similar iron contamination was achieved at a temperature of 700°C for 60 minutes duration with stoichiometric quantity of the reagent. Selective extraction of manganese with respect to iron is discussed.

Jan 1, 1996

By A E. C Peres, J D. Donda

With the aim of producing a concentrate with silica content lower than 1.0 per cent SiO2, laboratory experiments were conducted using a sample of the final concentrate from the Samarco iron ore flotation plant (mechanical cells circuit). The sample contained 3.08 per cent SiO2. This sample was split in two size ranges: >105 ¦m and 2. The >105 ¦m fraction, representing 23.3 per cent of the initial mass, was re-ground to 100 per cent 2 content were obtained. Considering the mass proportions of the two size fractions, the calculated silica content of the combined concentrate was 0.68 per cent, which is considered satisfactory for the objective of this investigation. The major reasons for the higher (0.90 per cent) silica content of the concentrate from the coarse fraction are the presence of silicon in the lattice of goethite and the presence of residual silicious slimes in the pores of porous hematite.

Jan 1, 2005

The Century zinc-lead orebody was discovered in 1990 and contains sufficient reserves to sustain open cut mining at 5 Mtpa of ore for approximately 20 years. It is proposed to pipe mineral concentrate in slurry form 300 km from the mine to the port of Karumba on the Gulf of Carpentaria. The concentrate will be dewatered at Karumba before being transported off-shore to deeper water in a self-unloading shuttle vessel for transfer to export bulk carriers. The four main environmental issues that attracted attention during the impact assessment phase of the project were: the selection of Karumba as the export port, the use of a pipeline to transport concentrate, the risk of concentrate spillage in the marine environment, and aquifer drawdown in the vicinity of the mine. This paper discusses these issues with emphasis on the context of the relationship between the Pasminco Century Project and Gulf communities. Environmental safeguards are discussed, including those that arose out of the negotiations regarding Aboriginal native title.

Jan 1, 1998

By P Wollants, B Blanpain, R Ding

Vacuum oxygen decarburisation (VOD) is the refining process used by ALZ (Genk, Belgium) for their production of stainless steels. The process consists of three stages: oxygen blowing at a pressure of 100 mbar, degassing, and reduction of the slag with ferrosilicon at 5 mbar. The magnesia-chromite bricks used in the slag zone of the ladles suffer from acute wear. In this paper results obtained from a program to improve the refractory life span are presented. The dominant wear phenomena were identified with an electron microscopy study of bricks taken from different locations in the ladle. Concurrently a dynamic model for the vacuum oxygen decarburisation (VOD) refining process was developed. The model calculates the elementsÆ oxidation rate during the blowing oxygen stage and allows the continuous calculation of the change of the metal, slag and gas composition throughout the VOD process. From these activities a general scheme of the refractory wear was worked out and measures to improve the refractory life were proposed and implemented.

Jan 1, 2000

Due to geographical location, AustraliaÆs economy and trading are closely related to Asia. With ChinaÆs increasing demand on resources and energy and Japan and KoreaÆs steady imports in these fields, AustraliaÆs mining industry is experiencing a so called æboomÆ period. Traditionally, engineers or skilled workers from South Africa, Britian or other parts of Europe moved to Australia for its mining industry. Now, more students from Asia are starting to choose mining engineering (similar choices include mining geology, metallurgy, geotechnical engineering and mining surveying) and expect to work in these fields. How does AustraliaÆs mining industry face such a situation? What kinds of challenges and opportunities do the mining industry and universities face? How do mining companies utilise these human resources? This paper concludes with an analysis of all these questions at an industrial level and some personal deduction as to the preferred course for international students.

Jan 1, 2005

By Yamakita T, Yoneoka Y

The Chigirishima Smelter of Toho,Zinc Co., Ltd. is the largest independent custom lead smelter in Japan and produces about 60,000 tonnes/yr of electrolytic lead. The quantity of slag produced by blast furnace is approximately 65,000 tonnes/yr, 30,000 tonnes/yr of which is sent back to the sintering plant for mixing with lead concentrates. The remaining slag used to be piled up at the yard until the operation of the fuming plant started in July 1977. We examined the slag fuming process with the purpose of achieving: 1) Improvement of the operating results by recovering zinc and lead from blast furnace slag. The lead content in slag at Chigirishima is slightly high, because the height of blast furnace shaft is low and consequently the quantity of sinter smelted per area at tuyere level is rather large. 2) Production of a salable slag as raw material for cement by lowering zinc and lead content in slag.

Jan 1, 1980

Separation in magnetic fluids is one of the modern techniques that offer a unique approach to material manipulation in a broad spectrum of industries. Its wide-scale application has been restricted so far for a variety of reasons, including limited throughput, inefficient recovery of magnetic fluids and the cost of commercially available magnetic fluids. This situation has changed recently. Very selective separators, with automated density control, capable of treating a variety of materials in a wide spectrum of densities and particle sizes have been built by DebTech and applied in the diamond industry. Technology for the recovery of magnetic fluids has been developed and low-cost magnetic fluids, with high magnetisation and low viscosity are being produced on a production scale. Scale-up of the technology has been addressed and units capable of treating large tonnages of material have been designed. Such a development thus offers the minerals industry a technology that surpasses the existing technologies in selectivity, efficiency and versatility

Jan 1, 2000

By Gee C. E

Ore reserves at the Kambalda Nickel Operations of Western Mining Corporation are estimated using the polygonal method for calculating areas of influence of drillholes. All raw assay and survey data are stored on one disk pack on the Company's CYBER 73 computer located in Perth, about 600 km from Kambalda. The initial step involving the computer is to search all assay data and calculate all potential ore-grade intersections. As the orebodies are thin, structurally complex and many are in close stratigraphic proximity, the selection of intersections which have the best grade over at least a minimum mining width involves complex logic. The orientation of an ore surface at each drill intersection point and a zone code are added to each intersection by the geologist from geological plans prepared for each ore surface. The orientation data together with downhole surveys enables the calculation of inter- section true widths and the zone code links each recalculated intersection to the appropriate ore surface.

Jan 1, 1977

During conventional eddy current separation, a repulsive force is applied to metallic particles by placing them in a rapidly changing magnetic field generated by a spinning magnetic rotor carrying an arrangement of alternate magnetic poles. This method works effectively for larger non-ferrous metallic objects, such as aluminium cans, but as the metallic particles become smaller, the bulk repulsive force on the particles is increasingly replaced by a rotational torque. Therefore, for small metallic particles it makes sense to use particle rotation, rather than particle repulsion, to effect a separation. Eddy current separators using particle rotation are similar in construction to present separators, but are designed to produce a rotating field of essentially constant angular velocity and field strength. Practical and economic particle rotation eddy current separations are possible down to particle sizes of about 200 ¦m, but separations, at probably uneconomic rates, can be carried out on particles as small as 50 ¦m.

Jan 1, 2000

By Barnes E. L S

With the introduction of diesel powered loading and hauling equipment, a number of Australian mines producing less than one million tonnes per year from shallow orebodies have been dev- eloped by decline. This method of entry has the advantage of providing both flexible access and early prod uction. However, as the depth of mining increases so does the operating cost of haulage, due to the need for more trucks. This cost, together with increased capital requirements for both equipment and infrastructure, leads to the point where the alternat- ive of shaft hoisting must be con- sidered. With an established decline it is possible to provide an ore hoisting shaft using a drilled raise with subsequent stripping to a suitable size. Using DCF techniques and known equipment operating and capital costs, an economic comparison of the two systems is made to determine the limit- ing depth to which truck haulage can be used.

Jan 1, 1973

By Chappell BW

A zone of northwest trending dykes extends for over 600 km in the hinterland from Cairns to Mackay. In sate regions the zone is up to 120 km wide. Figure 1 shows their approximate extent, compiled from published regional maps and from specific studies in more limited areas : Palm Islands, Cardwell Ranges, Jourama Falls, Townsville area and Burdekin Delta. The context of the dyke swarm is the Tasman Orogenic Zone, the region of Eastern Australia conprised of Palaeozoic metamorphic, sedimentary, volcanic and plutonic rocks which has experienced a complex history and evolution. In the Whitsunday region, the Tam-an Zone also involves Cretaceous volcanism and plutonism. Geological relationships indicated a wide span of ages for the intrusions in the dyke, swarm zone. They intrude a range of volcanic and sedimentary rocks, and in some areas plutonic rocks. Older dykes, apparently part of the same regional swarm are intruded by sate of the granites.

Jan 1, 1987

By Proffett JM

Batu Hijau is a calc-alkaline, island arc porphyry copper-gold deposit located in the southwest corner of Sumbawa Island in the Banda archipelago of southern Indonesia. Proven and probable reserves are 913 million tonnes at an average grade of 0.53 per cent copper (10.631 billion pounds Cu) and 0.41 g/t gold (389 tonnes Au). Construction of the deposit infrastructure began in October 1996, and formal approval for the project mobilisation was granted by the Indonesian government in May 1997. Preoperational testing and start-up of the first grinding line is scheduled for mid-year 1999.Copper and gold mineralisation are genetically related to at least three tonalite porphyry dykes and small plugs which intrude a quartz diorite stock that was emplaced into andesitic to dacitic pyroclastic rocks and lava flows. Faults are uncommon, and where they occur they do not significantly displace hydrothermal alteration and mineralisation zones.

Jan 1, 1997

The seam gas content at Westcliff Colliery is 12-15m3/tonne of coal.Composition ranges from 99% CH4 to 52% C02 in one area. Desorption rates are proportional to gas contents and CH4 is preferentially desorbed. A crushed zone of reduced permeability advances with the face - at Westcliff ribside crushed zones are 2.5 to 6.5m wide. Poor strata control widens crushed zones. 12 months of pre-drainage allowed 2 heading development and longer pillars to be used in a virgin area instead of 3 or more headings without drainage. Machined coal may lose as much as 1.6m3/tonne being conveyed out of Westcliff Colliery. Experience differs from mine to mine. Permeation is affected by time, strata movements, changing water content, and changing stress. Permeabilities vary from lOmd for Pittsburgh Seam to less than 1 and for the Bulli Seam. All these data and differences await further investigation.

Jan 1, 1982

Drilling and blasting operations have historically been viewed as a necessary 'evil' part of mining, whose costs should be minimised by whatever means possible. In the past, when operations depended primarily on crushing and milling for ore re

Jan 1, 1998

Incremental sampling is defined as a solution to fight segregation, the theory is demonstrated and theoretical and practical aspects are discussed. The number of increments necessary for successful sampling is discussed. As an application, riffle splitter division is reviewed.

Mar 1, 2010

The degree of ionicity-covalency of complex compounds is discussed here as a prospective criterion for selection and purposeful synthesis of sulfhydril and oxhydril collectors. Theoretical predictions of flotation behaviour were confirmed by flotation of a number of ores.

Jan 1, 2005

By Churchill J

A suite of software programs has been written to provide the field engineer or geologist with the capability to collect and store data directly into small, portable handheld computers. This allows the engineer and geologist to collect data in a more efficient manner as the data is collected in sequence and is verified at the time. Typical applications for this software include geological and geophysical logging, trucking surveys, mine surveying, condition monitoring, ventilation surveys and maintenance systems. The software allows the user to construct his own electronic notebook by structuring data input to the computer in a similar manner as is now done on pre-printed forms. The user can store all valid entry codes or numeric ranges in a dictionary and all data inputs made are validated against this dictionary. Once constructed the user may call the electronic data sheet into the unit and collect data which will be stored into the unit which has the memory capacity to record data for up to periods of 60 hours. The data can then be automatically transferred to mini/microcomputers for immediate analysis and report generation. The software may be used on a variety of handheld computers.However the generally rugged environments found in the mining industry limit the choices. In particular the authors have selected a unit weighing a little over one kilogram, which is rugged enough to fall off an underground survey vehicle, and survive when accidentally immersed in water,without losing data. This paper describes the software developments in detail. The project development work to produce this system has been funded by a grant from the Australian Mineral Industries Research Association and is supported by a number of large Australian mining companies.

Jan 1, 1986

The GDR has extensive lignite deposits at its disposal, which formed the basis for the development of an independent energy source after 1945 and which will retain their significance well beyond the year 2000 (see fig. 1). In 1946 lignite output was about 110 x 106 t. In 1985 312x 106 t was produced and in 1988 the planned output will be ca. 315 x 106 t. Thus, the domestic produc- tion of lignite covers ca. 75% of the GDR's primary energy requirements. More than 80% of the electrical energy is gener- ated by the use of lignite and about 12% by nuclear energy. In addition to this, about 18 x 106 t/a mineral oil and about 6 x 109, m3/a natural gas are imported, predominantly from the Soviet Union. The lignite deposits of the GDR are of Tertiary origin and are recovered exclusively by opencast mining. There are two large regions (fig. 2): - in the region east of the river Elbe (Cottbus/Senftenberg- "Niederlausitz") and - in the region west of the river Elbe (Halle/Leip- zig/Magdeburg). These deposits differ in geological age and conditions of depo- sition, consequently there are differences in their chemical and physical composition and, thus, in their uses. The younger Mio- cene coals of the main region in the East of the river Elbe belong to the epirogenetic type and have a low content of ash and sul- phur. Among other things, they are suitable for the production of brown coal high-temperature coke (Lauchhammer and Schwarze Pumpe). The older Oligocene coals of the Halle/Leip- zig region are bitumenous in certain areas. Therefore, they form the basis for production in low-temperature carbonizing and chemical plants. In the Halle-Magdeburg region, where the lig- nite is in contact with the underlying Zechstein subdivision, so- called "salt coals" are found.

Jan 1, 1989

IN preparing a sample of refined lead for analysis, it is necessary to exercise great care to avoid contaminatien, as the amounts of the various impurities present in market lead are very small. The lead is cut into convenient-sized pieces, which are flattened out with a hammer, so that, on putting tbe lead through the rolls, strips of about one inch in width and Ij32iu. in thickness are obtained. The hammer, anvil, and rolls should be carefully cleaned before use. The strips oflead are cut up into pieces of about one inch square. If the lead is roIled out very thin and cut up into small pieces there is considerable risk of the acid acting too violently and causing loss through frothing over. A blank assay on all the reagents used should becarried right through, along with the actual analysis of the lead. This is of the greatest importance, particularly with regard to the determination of such impurities as iron, sulphur, arsenic, and antimony.METHOD OF ANALYSISThe method of analysis is as follows: Take two lots of 600 gIm. each, place in a large beaker, add 2000 cc. distilled water and 750 cc. concentrated HNOs. Cover with a clock glass and warm on a hot asbestos plate until all action ceases. (If any white precipitate forms, filter off and examine for Sn and Sb.) Add 420 cc. H2S04 (1-1), and stir well while adding the acid: Allow PbS04 to settle, pour off the clear liquid into a 12-in. porcelain evaporating dish, and start evaporating down, the dish being placed directly on an 8-in. ring gas burner. Wash the precipitate three times by decantation using approximately 1200 cc. hot water for each washing, and stir well...

Jan 1, 1922