Search Documents

By Harrison J

The correct selection of equipment to use in a mine is a problem which constantly faces the mining engineer. In some cases a wide choice of equipment with different operating characteristics is available. If this equipment is to be used to assist in moving the ore it may be possible to build a computer simulation model to predict how it will perform. Typical problems that lend themselves to this type of analysis are presented. The computer models are constructed using a recent form of the GPSS computer language, namely GPSS/PC for the personal computer. This language allows the programmer to construct models in a very short time and at a low cost. Of great importance is the easy way in which it is possible to change the models to answer any of the "what if?" questions the engineer may pose.

Jan 1, 1987

By Warren R

Croesus Shaft is one of two operating shafts on North Kalgurli Mines Limited's Fimiston lease.At the cessation of gold mining in 1974, the workings at Croesus were allowed to flood. Large quantities of deslimed mill tailings used in filled stopes were washed into the shaft and surrounding drives, making re-access very difficult. The shaft has been desludged from the 9 level to the 15 level, and a loading pocket installed below the 14 level. A vacuum lift unit was installed underground to facilitate the removal of the slime and spillage.Stoping at Croesus was hampered by poor drainage, pumping, and shaft availability. These difficulties have been overcome by utilising an open stoping system for the relatively steep, narrow, high grade stopes. Open stoping has proved to be effective and economic.

Jan 1, 1985

By Moore R. F, Macias L. F

The Filbara region of northwestern Western Australia contains several known occurrences of mafic/ultramafic rock assemblages which may host platinum group element (POE) mineralisation. This paper deals with occurrences at Munni Munni and Andover. The Munni Munni complex is of particular interest because it is known to contain PGE mineralisation and is currently undergoing active exploration. The US/Australia Joint Scanner Project of October 1985 collected airborne scanner data for the BMR over Munni Munni. Such an ultramafic-mafic complex had not been previously researched with advanced remote sensing instrumentation. Extensive investigation of data from the NSOO1 (Thematic Mapper Simulator) scanner resulted in successful differentiation of gabbroic and ultramafic rocks, and also subdivision within the ultramafies. Similar differentiation could not be achieved using conventional Landsat MSS imagery and aerial photography. Encouraged by those results and in support of BMR field research into the mafic-ultramafic suites of the region, data from the Landsat Thematic Mapper (TM) instrument were investigated to attempt differentiation of the ultramafic and mafic rocks in the Andover complex some 50 km to the northeast of Munni Munni.

Jan 1, 1988

By M Reisi, H Waterer, M Savelsbergh, F Engineer

The Hunter Valley Coal Chain Coordinator (HVCCC) Limited is the primary planning organisation responsible for the export of coal through the Port of Newcastle, Australia. HVCCC stakeholders include producers (mining companies), rail track owners, above rail operators, and terminal operators. The HVCCC is tasked with coordinating the activities of all the corresponding parts of the coal export supply chain so as to maximise the system efficiency. The HVCCC also has a forward looking planning role: with demand for coal expected to double in the next decade, strategic capacity planning is a core activity for the HVCCC. Optimisation and simulation models are key aids in such activity. They are used to suggest and evaluate infrastructure expansions and operating policy changes. These models require input data in the form of shipping stems, which are arrival streams of ships at the port, together with their cargo types and composition, and date and time of arrival.Although everyone is familiar with the expression ægarbage in equals garbage outÆ, relatively little research is dedicated to the issues surrounding input data generation. In this research we seek to redress this, and have developed a method for generating high quality shipping data. Shipping stems used as input should be realistic, reflecting key characteristics of historical patterns. They should accurately represent future demand scenarios. Yet they should also have controllable parameters that can be used to test what-if scenarios, such as are required by the HVCCC to answer questions about future infrastructure or operational plans.Here we review our process for achieving this, and give a case study analysing the effects of different shipping stems on the performance of the coal chain, as measured by a capacity assessment tool. The latter is an optimisation model that takes shipping stem and infrastructure data as input, and calculates key supply chain performance metrics. The potential benefits of alternative demand management strategies are analysed by measuring the performance of the coal chain given different shipping stems obtained via the stem generatorÆs controllable parameters.

Sep 26, 2011

A metallurgical balance drawn around a mineral processing plant or smelter must involve all process streams crossing the plant boundary. Modern sampling theory, as formulated by Gy, and sound statistical method can be used to determine the uncertainties in the observed assays for the set of balance analytes and in the mass flow rates of the process streams for the balance period. These uncertainties can then be used together with the material balance equations to arrive at adjusted component mass flows that satisfy the material balances exactly. To determine whether or not the data is consistent with the level of uncertainty in the data and with the material balance equations, a goodness of fit test is applied. This goodness of fit criterion is the principal tool to quantify the quality of the material balances. The mathematical structure of the statistical material balance problem poses a number of challenges. For example, while the variances of the adjusted component mass flows do not vanish, the variances of the sums of the adjusted component mass flows about each balance node do vanish, simply because the balancing computation demands that the balances close exactly. Even though it can be shown that the variances of the adjusted component mass flows are always lower than the estimates for the corresponding unadjusted component flows, it is still not possible to construct a confidence interval on the component mass flow into (and out of) a balance node using the adjusted component flows. On the face of it, such a confidence interval is exactly what is most desired from the balance calculations. The problem arises because the balance problem is a data adjustment rather than a parameter estimation problem. It is possible, however, to calculate the recovery of a component to a product stream and determine a confidence interval for the recovery value. It is also possible to calculate an uncertainty in the mass flow of any balance species in any process stream, before and after balancing.

Jan 1, 2005

Using a Jarrell-Ash "Compact" direct reading spectrometer, analyses were made of a wide variety of rocks ranging from acidic to ultrabasic types. Statistical evaluation suggests that accuracies comparable with the values obtained by the rapid chemical methods used by the United States Geological Survey will be obtained.The spectrographic method involves fusion of the rock with lithium tetraborate, strontium being incorporated in the flux as the internal standard. The resulting bead is ground with graphite and pressed into a pellet. The counts obtained on two standard pellets are used to correct for instrumental drift.Background readings are made at 4109 Å and corrections for background are made to all lines. Corrections for matrix interferences, both by chemical suppression and optical enhancement, are made. The three corrections of drift, background, and matrix are incorporated into one general expression which has been programmed on magnetic cards, each element requiring a separate card. The cards are placed individually into a desk top computer (an Olivetti Programma 101), which enables true counts to be calculated from the "readout" counts, and the element concentration is then obtained from computer-printed tables by referring to the appropriate value of true counts versus concentration. These tables were prepared by making a polynomial regression analysis of the spectrographic results from 50 standard and analysed samples, a curve of best fit being chosen for each element.The regression coefficients, usually of a fourth or fifth degree equation, together with other relevant data, were fed into a large computer, programmed to print out tables of concentration versus true counts. This technique enables the results obtained to be based on mathematically-derived values rather than on hand-drawn calibration graphs, giving greater inherent accuracy. The technique has been shown to give results of good accuracy and acceptable precision suitable for many geological and geochemical exploration programmes involving the analysis of many rock samples of different types.

Jan 1, 1969

By P Cundall

Three-dimensional DEM (Distinct Element Method) simulations were conducted in order to examine the performance of screw conveyors, which are installed to transport bulk materials as parts of many industrial machines, including mining and construction machinery. To apply the DEM to the analysis of screw conveyors, we added a spiral object and cylinder objects, which correspond to the helical screw, the casing pipe, and the driving shaft of a screw conveyor. These objects are represented analytically to enhance the precision and efficiency when calculating the interaction between objects and particles. Simulations were conducted for some real applications: inclined and other types of screws, as well as the basic types (horizontal and vertical). Results were compared with previous work and empirical equations. It is concluded that this method is sufficiently well-developed and useful to analyse various kinds of screw conveyors.

Jan 1, 2000

By Hayes K. M, Ostwald J

Compacted tablets of hematite ore (containing clay and quartz gangue) and limestone were heated in air in an ULVAC-RIKO rapid heating furnace to maximum temperatures in the range 1200-1350°C.The resulting sintered products were examined in terms of mineralogy, texture, strength and reducibility. The sintered tablets are a good analogue of normal plant sinters. These investigations have shown that sinters of optimum reducibility are produced in the narrow temperature range 1250-l275°C. Conditions for the production of such highly reducible sinters under plant conditions are discussed.

Jan 1, 1984

By A S. Ray, P S. Thomas

The characterisation of the surface area and porosity of opals derived from Tintenbar, a volcanic environment, and Lightning Ridge, a sedimentary environment, using nitrogen gas adsorption at -196¦C is reported. Both opal types were found to have relatively low surface areas and displayed little porosity. The low surface areas observed is indicative of the ability of silica to infill voids and interstices. Thermogravimetric analysis of the samples before and after degassing was carried out to determine the amount of water removed by the degassing process. Negligible difference was found in the water content before and after degassing in the case of the Lightning Ridge sedimentary opal, while the Tintenbar volcanic opal was found to have lost more that 60 per cent of its water during the degassing process. These differences were ascribed to the differences in the silica structure of the opals with the Lightning Ridge opal having a denser cage structure, which traps the molecular water, while a more open structure is postulated for the Tintenbar opal, allowing the water to be relatively easily removed.

Jan 1, 2008

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

Proper technical appraisal of a coal deposit and the determination of optimum open- pit mine design can only be made after detailed examination of a number of interrelated geographical and geological factors. Initial evaluation of the geography and the overall attitude of the coal measures can often determine the most likely coal mining technique. Conclusions reached in the early stage of the investigations frequently dictate the quality and quantity of particular types of data required from further drilling of the deposit. In many cases, insufficient information relating to the overall engineering aspects of a coal deposit is derived from drilling. Little or no attention is paid in the exploratory phase to such things as the specific gravity of selected overburden samples, floor conditions, clay content of the overburden and selected strength tests on cores. This is a direct result of geologists treating coal deposits purely in geological terms without sufficient consideration being given to the engineering parameters required for a proper evaluation of the deposit.

Jan 1, 1977

By Moelle KHR

The successful operation of a longwall face depends significantly on the efficient actions by support systems and on the ability to form a supported beam for a limited time span.The mechanical action of the supports can set up complex stresses in the immediate roofstrata.The cyclic application of supporting loads to the immediate roofstrata of a longwall face creates a special type of fabric disintegration in the rocks -affected. The mode of application and the distribution of the supporting forces is thus severely modified in a number of cases.The occurrence of true fatigue damage in brittle sandstones has been identified by studying the subcritical crack growth and microcrack development in the fracture-tip region. Several mechanical effects peculiar to the cyclic fatigue process have been identified. These effects had not previously been widely recognized. Damage in brittle rocks subjected to cyclic loads is shown to be distinctly different from any other damage processes under either monotonic or sustained (creep) loading conditions. The face support systems will frequently support rockmasses with mechanical properties not identified in conventional monotonic or sustained load tests.

Jan 1, 1991

By M Warren

The professional geologist or engineer on a mining operation has a particular view of their operation. This is based on the factors of the operation that have a direct impact on the daily work program of the professional, such as production rates and grades. The view that would be taken by a financier who is called upon to support the project may be somewhat different. The value of the operation to the financier is in its ability to generate surplus cash for its owners and thus repay the debts to the financiers, with as low risks profile as possible. A number of tools are used to test the sensitivity of the project to variations in the key cost/revenue drivers. The Financier may call on a team of technical specialists to assist with the assessment of the cash flow and risk profile and to monitor the development of the project. The ability to offset this risk, as all projects have some degree of risk, may be a key factor in determining the level of financial support to be offered.

Jan 1, 2002

The results of the washing of coal are often presented by using Partition Curves. By analogy, it is possible to express the results of screening by using similar partition curves. As in the coal washing processes, this method determines the accuracy of screening and is also suitable for different separations depending on the difference in size distribu- tion. This method compares the effectiveness of two screening operations and forecasts the performances.

Jan 1, 1984

By Blake W

Based on preliminary computer model simulations and stability analyses, both longi- tudinal and transverse, large dimension, cut- and-fill rooms were designed for the parallel dipping ore layers at Kamoto mine. Full scale testing of the designed rooms showed that the rooms are stable and that the rock behavior is predictable. Ordinary waste rock was selected as the filling material because the fill was found to carry little load.

Jan 1, 1973

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

By S McKnight, S Hall

Much of the research regarding the use of bacteria for the oxidation of sulfide minerals has been conducted using pure bacterial strains or synthetic minerals, often under ideal conditions, which does not reflect the conditions commonly encountered in commercially operating plants. This has also led to much conjecture as to the exact mechanism by which bacteria are able to enhance sulfide oxidation and as to which species of bacterial microflora are the most dominant. Recent advances in 16S rNA sequencing has confirmed that many of the bacterial species once thought to dominate commercial oxidation circuits were simply more willing to grow under the culturing conditions used and may only play a minor role in the oxidation process (Rawlings, 2002). Consequently this research will look at bacterial oxidation under conditions more reflective of commercial operations, focusing on the presence of organic carbonaceous material within a refractory sulfide orebody to be sourced from the Fosterville deposit of Perseverance Corporation Limited.

Jan 1, 2004

Seam gases are the most important atmos- phere contaminants in Australian collieries, their importance increasing with depth; C02 as well as CH4 may be important in intruded envir- onments. The generally high rank of the coal, with low moisture content, makes for abnormal dust production. The other contaminants are introduced and subject to better control, in- cluding products of spontaneous combustion. Due to market situations the generally lower rank and higher sulphur coals more prone to self heating are mined less. Future mining at greater depths should see greater problems with atmosphere contaminants.

Jan 1, 1983

By Palmer DJ, Bain JH, Pullen JB

Over the last ten years at Risdon, zinc production capacity has almost doubled. This has resulted in modifications, many of which have affected zinc deposition operating conditions in the cells. Some of these changes appeared to have affected average current efficiency to such an extent that a special investigation was initiated, using multiple regression analysis to assess historic cell unit operating para- meters. The study highlighted the importance of certain parameters in maintaining maximum current efficiency for zinc deposition from !Risdon purified solutions under conditions of !changing current density, acidity and zinc con- centrations. Maximum current efficiency was obtained only within a zinc to acid ratio in cell electrolyte of 0.45 - 0.55 and a residual zinc concentration greater than 48 g.1-1, irrespective of actual zinc concentration or The investigation also established: ieters giving minimum power consumption at termined current density; the effect of ntration changes in common impurities on nt efficiency; the existence of high s of some impurities in solids precipit- in the cells and pure solution tanks.

Jan 1, 1975

The major heavy industrial consumers of limestone are the cement, lime'and steel ind- ustries. Each of these requires large quantities of cheap raw material. Other ind- ustries such as glass and chemical manufactur- ing are significant consumers and agricultur- al and constructional activities provide additional demand which is usually more local in its occurrence. Limestone is widely dis- tributed throughout Australia but location in relation to major markets, and transport con- siderations render most deposits of no economic value. Among deposits which are sufficiently close to the major metropolitan markets many must be rejected as being unsuitable on grounds of quality, inadequate size for major.develop- ment, or other reasons such as environmental considerations. The major producing locations are sit- uated in a variety of geological environments. Most have limited reserves and require partic- ular attention to quality control. Planned extraction programmes based on detailed geo- logical investigations enable not only satis- factory grade control but also permit, by the adoption of appropriate quarry procedures, the use of sub-grade material, thus optimis- ing utilisation of the available reserves.

Jan 1, 1976