Search Documents

By Duran A, Eggers M. J

It is standard practice in geotechnical studies for mine design to drill a series of inclined oriented boreholes into the proposed pit walls. However, this investigation tool is often used without an adequate understanding of the inherent shortcomings in the method and the many potential sources of error. Of the more commonly used orientation methods in Australia the clay imprint technique is probably the most reliable. Contoured stereographic plots of oriented core data are frequently characterised by diverse pole distributions and low concentration maximums compared with line mapping data. Common sources of error producing these poor results are misinterpretation of orientation marks or imprints, inaccurate marking of the reference line, errors in the structural measurement of the defects, lack of continuity information and blind zones sub-parallel to the borehole direction which correction methods frequently do not fix. Line mapping is the preferred method of structural data collection due to the lower overall cost, availability of continuity information and higher accuracy. The projectability of field mapping data to final wall positions can be assessed with a good understanding of the regional geology and local structural patterns. Where field mapping is not possible due to a thick regolith cover, core orientation should be carried out by experienced personnel to minimise the many potential errors.A series of case studies are presented which compare oriented core with mapping and highlight the inherent problems with the technique.

Jan 1, 1992

By A Califice, E Pirard, M Benzaazoua, R Mermillod-Blondin

Image analysis is more and more considered as a powerful tool for quantitative analysis of ores and concentrates. Apart from being very much dependent upon the quality of the imaging principle and the adequacy of the imaging sensor, quantitative image analysis is also the result of a long chain of material, image and pixel sampling strategies. The most reliable way to demonstrate the accuracy and the precision of modal analysis obtained from images is probably to use a blended material with known proportions of pure minerals and confront the results obtained from different analytical tools. This operation has been performed on a series of mineral blends mimicking the tailings of a flotation operation in a plant operating on massive sulfide mineralisation. The intention was to be able to better predict acid mine drainage potential from direct mineralogical observations. Selected sulfide minerals: pyrite (Py), pyrrhotite (Po), chalcopyrite (Cp) and sphalerite (Sp) were mixed as variable amounts within gangue minerals (quartz, calcite, dolomite and siderite). Typical blends contained six to ten per cent (Py); one to three per cent (Po); 0.5 to one per cent (Cp, Sp); 15 to 40 per cent carbonates and 40 to 75 per cent quartz by mass. The 1000 gram blends were carefully sampled and prepared for X-ray diffraction, chemical analysis by ICP-AES and optical microscopy image analysis (OMIA). Results obtained for the different analytical techniques are compared and discussed revealing the limits and strength of each method in the accurate quantification of sulfide and gangue minerals.

Jan 1, 2008

By Fisher WJ

The'treatment of the South Alligator valley uranium ores passed through three phases dictated by economic circumstances during the years 1956- 640 In the first phase high grade ores were treated by hand sorting and wet gravity separation for recovery of high grade concentrate to meet a United States Atomic Energy Commission (U.S.A.E.C.) contract for plus 50 per cent pitchblende concentrates. Secondly tailings from the gravity plant and some high grade ores were trucked to Rum Jungle and sold to the Australian Atomic Energy Comm- ission (A.A.E.C.). Thirdly solvent extraction plants were built at Moline (previously Northern Hercules) by United Uranium N.L. (UOU.N.L.) and at the South Alligator River by South Alligator Uranium N.L. (SOA.U.N.L.). These were the first solvent extraction plants designed in Australia, as earlier plants used the ion exchange process for recovery of uranium oxide. The plants were small, indeed the S.A.U.N.L. 15 ton per day plant was possibly the smallest commercial plant known, but they operated efficiently with good recoveries, and were placed on a care and maintenance'òbasis when contracts were filled. Sulphuric acid was supplied in bulk to both plants by the A.A.E.C. from the 30 ton a day acid plant at Rum Jungle. Gold was recovered as a by product of uranium ore from the Moline plant.

Jan 1, 1968

By Tyson G. R

A novel system has been developed using computer imaging techniques to make on-line measurements of material on a moving conveyor. Meas- urements of the mass or volume of conveyor materials are important in large open pit mining operations such as those operated by the State Elec- tricity Commission of Victoria (SECV). Such on-line measurements can be used for monitoring and controlling the production and transport of coal or overburden, and to assist in maintaining production levels. This paper describes a conveyor burden volume measurement system which is currently under development at the Research and Development Department of the SECV and although targeted initially for use in the Commission's open cut mines, the system is suitable for use on any open conveyor system. A basic developmental system has been built to demon- strate the viability of the technique used and further work on the system is planned. The measurement technique and the major components which have been developed as part of the system are described, some comparisons are drawn with other existing measurement systems and potential errors and future development are discussed.

Jan 1, 1989

In general, modern mining companies all over the world have to face the same economic circumstances as any other part of the industry: considering the tough competition, production and haulage costs must be reduced permanently whereas productivity has to increase substantially in order to remain price-competitive. However, the imposed pressure also offers the chance for consideration of alternative mining concepts, the application of which can result in substantial cost savings and improvements in the quality of the mined material. As one of these alternative mining concepts, surface mining technology offers substantial improvements in productivity. It also influences aspects of haulage, such as safety and speed, in a positive way. The capability of selective mining ties in nicely with the production of small-sized crushed material, the granulometry of which allows the elimination of the primary crusher. Mine operators profit from reduced costs for the maintenance of their haulage vehicles due to reduced wear, a decreased likelihood of accidents and higher average transport speeds. Surface Miners can also be used to cut haul roads into virgin rocks and leave a clean and level surface behind, improving the quality of these created roads. Thus, it is even possible to use ordinary road trucks for transport in mines. The current paper outlines in detail the effects of the surface mining technology on mining and haulage aspects and reports on applications where substantial cost savings could be achieved due to the application of what is also referred to as æsimple mining processÆ.

Jan 1, 2003

By A. W. CAMERON

Over a 4 hr period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc, and gangue minerals, size by size throughout the whole circuit.Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had some reserve capacity.In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one-third of the lead losses in the final tails.All sizes of zinc values between 100 mesh and 7 microns floated well and the performance of the zinc flotation circuit was mainly limited by the relatively poor flotation of the very fine zinc values. Approximately 60 per cent of the zinc lost to the final tails lay within the minus 7 micron fraction.The overall flotation conditions were conducive to very good selective flotation of the major proportion of the values and limitations in metallurgical performance were mainly due to the properties of the ultra-fines.

Jan 1, 1971

In the past ten years or so there has been a renewed interest worldwide in the processing of refractory gold ores. The Archean province of Western Australia contains both numerous and major gold deposits, and has a long history in the development and practise of treating refractory ores (eg Blaskett and Woodcock, 1953). Depletion of shallow oxidised ores in recent years has re-focused attention on deeper sulphidic ores, and as a consequence has renewed interest in treatment methods for those ores which are refractory. Mineralogical factors he at the heart of reasons as to why these ores are refractory, and are the key to designing and improving treatment options in the longer term. This paper presents an overview of mineralogical factors that are relevant to the processing of refractory gold ores in the Archean of Western Australia. It is based on a number of research projects and other work on a variety of gold deposits, mainly in the Eastern Goldfields region, carried out over the past five years or so.

Jan 1, 1991

By Wright S

Single pellets of mixed lead-zinc concentrate containing up to 20 % lead were roasted in the temperature range of 800-1100¦C. Variables studied included pellet size (from 9-8 to 3-2 mm diameter), gas flowrate past the pellet (from 0.05 to 5 ms t), composition of the atmosphere and the effect of additives such as zinc oxide and silica. After defined periods of time, the pellets were removed from the furnace, quenched and submitted for chemical, XRD, SEM and microprobe analysis. The oxidation of the zinc sulphide followed a shrinking core model. Temperature measurements showed that very high pellet temperatures were experienced at the start of an experiment but after 5-10 minutes these approached a constant temperature. The lead loss from the pellets was then constant with time. Thermodynamics predicted the presence of two bands of lead material in the reacted layer of the pellet. These were found in practice. The lead loss from the pellet occurred from the outer oxysulphate layer via the vaporization of lead oxide polymers. The vapour pressure of PbO, and the loss of lead, was dependent on temperature and bulk gas concentrations of SO2 and 02. At 1100¦C the addition of silica greatly reduced the loss of lead from the pellet. Physical factors such as pellet diameter and gas flowrate past the pellet affected the particle dynamics. These results were found to vary in accordance with the predictions of the Froessling equation.

Jan 1, 1989

By M Fimeri, R Williamson

Sample sizing in the iron ore industry requires significant manual effort to collect, transport, and sieve the samples as well as record, process and report the data. Efforts have been made to automate this process, which essentially emulate the manual process, except that a person is replaced by a robot. Even in these cells, the sieving and sizing operation consumes a significant proportion of robot time. The proposed doubling of production from AustraliaÆs iron ore mines over the next five years will place increasing pressure on sample sizing and interest is increasing in alternative automated methods. One such method is the adaptation of computer vision technology which has been successfully introduced into the mining industry in a range of applications including feed size distribution to SAG mills and oversize detection from screening stations. The limitation of this technology is that only the top surface is visible and this is used as an indicator of total size distribution. Obviously in a sample plant, where 100 per cent of the sample must be measured for acceptable quality assurance, this approach is unacceptable. In order to capture 100 per cent of the sample using computer vision technology a monolayer must be formed either by spreading the sample across a moving surface, such as a conveyor or vibrating platform, and passing this under a camera. This will become a æsurgingÆ load which presents specific problems for some types of computer vision systems, namely those relying on a 2D approach. In this paper a 3D computer vision technology will be described which overcomes the problems associated with measuring particle size in a monolayer and experimental results will be presented which demonstrate its effectiveness for lump and fine iron ore sample size measurement.

Jan 1, 2008

By O V. Vasyukova

Formation of porphyry-style ore deposits starts with the metal extraction from magmas at so-called magmatic-hydrothermal transition (MHT). The processes and compositions at MHT are difficult to study as the record of them is poorly preserved. As the MHT is characterised by massive crystallisation of quartz, including quartz æeyesÆ and veins, their study can elucidate questions related to metal transport and deposition. Quartz grains from the porphyry deposits all over the world (Antapaccay, Peru; Batu Hijao, Indonesia; Climax, USA; Panguna, PNG; Far Southeast porphyry, Philippines; Rio Blanco, Chile; Omsukchan, Russia) were studied by optical, SEM-CL and BSE microscopy, electron microprobe and LA ICPMS. Quartz grains, even within each sample, have different shapes (rounded, egg-shaped, amoeboid or euhedral) and cathodoluminesence (CL) patterns (shape, number and width of bands in CL images). The outer layers of quartz are markedly different, which is unexpected if the grains had formed in the same conditions. Inflections and blurring of CL bands are often structurally associated with fractures that are commonly healed with secondary quartz and associated fluid inclusions. Our results show that quartz æeyesÆ could not crystallise from a silicate melt as normal phenocrysts. It is likely that in situ segregation of residual SiO2- and H2O-rich liquid and its solidification followed by coagulation (eg formation of silica-gel globules) took place in the magma (crystal mush) during MHT. Such globules could remain in a plastic state for a long time even at rather low temperatures. The solidification of globules occurred after bands of different composition had formed and led to fracturing of solidified and inflection of unconsolidated layers. All fluids (liquid and vapour) released from the original silicagel during solidification were trapped as inclusions (aqueous, salt-rich and sulfide). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Lauha E. A

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike subdistrict, there are seven major deposits; Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the subdistrict are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Bamck Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post, and Deep Star occur both on Barrick and Newmont Property.

Jan 1, 1991

This paper describes the application of the Total Productive Management (TPM) technique as a performance improvement initiative for a coal mining operation. It discusses the objectives of TPM, with the driver for improved production performance being the Overall Equipment Effectiveness (OEE) of the equipment or process, and with the development of "ownership" as the behavioral approach to equipment management and continuous improvement through cross-functional and area-based teams. It illustrates the concept of equipment management as defects management.The scope for application of TPM to the coal mining industry is immense. The harshness of the operating environment can be a major generator of equipment defects, and a current paradigm in the industry accepts these defects as an unavoidable outcome defining maintenance costs in this environment. However recent benchmarking studies have highlighted that maintenance costs per operating hour in some mining operations are more than double the vendor's estimate of "best practice". The paper refers to these studies which also compare maintenance costs of fixed and mobile plant and equipment to "best practice" outcomes in comparable process industries.

Jan 1, 1998

By Lyman G. J, Ka

The use of images to determine blast fragmentation is the only feasible technique when one does not want to disturb the production cycle. However, three major problems exist with the use of images. The first is determining real size from a two-dimensional particle, the second is estimating the fines which are missing due to image resolution and particle size range, and the third is proper sampling such that a statistical probability can be calculated for the distribution. Once these problems are resolved, the tedious process of digitizing images by hand may be automated. This paper describes the present techniques used at the JKMRC to "size" blast fragmentation, estimate the missing fines using the Rosin-Rammler equation, determine the sampling error using Gy's sampling equations, and extract the particles from an image using an IBM-AT computer.

Jan 1, 1990

By Fabjanczyk M. W

The design of underground mine roadways (tunnels) requires a detailed understanding of the in situ stressfield, the rock failure modes, the performance characteristics of reinforcement or support members and assessment of the stress state about the roadway. Definition of these factors, together with monitoring of roadway behaviour during both development and extraction operations, allows rational design procedures to be undertaken.The design approach utilised computational techniques to simulate the behaviour of the strata about the opening for a range of anticipated stressfields and various reinforcement options. Field validation studies are conducted to confirm the design expectations.

Jan 1, 1993

By Caivin JS, Freeman CJ

The Fairbanks Mining District in central Alaska was discovered in 1902 and since then approximately 7.5 million troy oz of placer gold, 250,000 troy oz of lode gold, and several thousand short tons of antimony and tungsten hap been produced from an area of about 1000 km . Historic lode production was from high grade gold-quartz veins that averaged 1.3 OPT free milling gold. Five main types of mineral deposits' are recognized in the district. I. Conformable, stratabound volcanogenic zinc, antimony, lead, and copper sulfides in places containing gold, silver and tungsten in bimodal metavoleanics (Cleary Sequence). II. Complex precious metal-bearing lead sulfosalt-quartz veins in Cretaceous granitic intrusives. III. Tungsten skarns adjacent to granitic intrusives. IV. Gold-bearing polymetallic sulfide-quartz veins crosscutting metavolcanics and metasedimentary units of the Cleary Sequence. V. Antimony-bearing gash veins along axial plane shears in various lithologies of the Cleary Sequence. Type I and Type IV mineral occurrences are currently being evaluated as low. grade bulk tonnage (target model 16-20 'million tons of 0.05 to 0.15 OPT)'and high grade moderate tonnage (target model 0.5 to 2.5 million tons of 0.5 OPT) gold deposits. The host rocks for Type I mineralization occur over a 30 km strike length and are at least 300 meters thick. Stratigraphic, structural, fluid inclusion, and isotopic data suggest that the Type IV mineralization is related to remobilization of Type I

Jan 1, 1987

By R Lovel, P Fung, J Manuel, M OÆCo

The iron blast furnace is the most widely used and efficient producer of liquid iron. The integrated steel works is however under environmental pressure largely due to emissions from sintering and coking. The combustion of coke breeze during sintering contributes to greenhouse gases (eg carbon dioxide) and is the source of much of the emissions of SOx and NOx. Coke breeze, the fines produced during coking of coal, is also suffering supply issues as coke demand increases while coking capacity is constrained by environmental concerns.CSIRO Minerals has been investigating the use of wood biomass/char as a substitute for coke during sintering. Wood biomass, or char produced from it, is an attractive carbon source as carbon dioxide can be sequestered into growing biomass prior to combustion. It has great potential to reduce the emissions from integrated steelworks and improve their environmental acceptability. Harvested biomass/char is also a renewable and sustainable resource. Samples of pine wood flour, sawdust and red gum wood char were characterised and used in small-scale granulation and sintering tests. Red gum char granulated as well as coke and could be used to make acceptable sinter. Large-scale sinter pot test were conducted with char to produce sufficient sinter for ISO quality tests and calculate sintering performance parameters. Results showed that coke could be completely substituted by red gum char during sintering without loss of quality and with actual improvements in sintering performance. Furthermore, gas analyses made during sintering showed that there were significant reductions in SOx and NOx when char was substituted for coke. It is anticipated that the results reported here, although preliminary, will stimulate an increased effort into further research on the use of char in iron ore sintering.

Jan 1, 2004

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By E Werner, B R. Leavitt

The chemistry of acidic mine drainage discharging from flooded coal mines is commonly reported to improve with time after flooding. This investigation describes a 18-year dataset of post-flooding water chemistry for a below-drainage underground coal mine within the northern Pittsburgh coal basin (Pennsylvania, USA). The Montour mine is a 5650-hectare below-drainage coal mine of maximum 260 metres depth. Montour was closed in 1980 and flooded to within 38 metres of land surface within 4.8 years. Pumping averaging 210 L/s was then employed to maintain water levels at this elevation. The flooded proportion of the mine (by volume) at full flooding was 56 per cent. The shaft where water was pumped from Montour for water control is located about 70 per cent of the distance between the mine water table and the back of the mine ù that is, it is close to the back of the mine. The residence time (total water volume at flooding divided by pumping rate for control) is estimated at 5.6 years. Time series of chemical analyses show three phases of chemical behavior in post-flooding discharge. In Phase I (zero to two years after flooding), iron concentrations were high and reached their maximum (1100 mg/L). In Phase II (two to four years after flooding), a transition was begun to alkaline conditions, with decline in iron and other solutes. In Phase III (>4 years), net alkaline conditions began, with iron concentrations declining exponentially to 50 per cent of mined volume. This attainment of net alkalinity in this case may have also depended on abundant calcite in overburden extended up to 30 m above the mine floor.

Jan 1, 2003

The occurrence of metallic minerals in Australia to the time of the proclamation of South Australia as a Colony in 1836 was unknown. It is, therefore, perhaps, surprising that British settlers arriving in the Coromandel included among their number a German scientist Johannes Menge who had been appointed by the South Australian Company to the post of Mine and Quarry Agent and Geologist on 1 July 1836. His instructions were to `explore the natural productions of the Colony above and below ground and to superintend the working of quarries of stone and slate, the boring for water, metal, lead, coal and other mines at a salary of ú150 per annum for one year and for as much longer as the Company require your services not however exceeding five years'. In the event, he was to have little influence on those matter.

Jan 1, 1993

By Gallet M, Watsford R. M S

The 1989 feasibility study of the chessy, france, copper, zinc, pyrite and barite orebody was based upon a classical flowsheet. The flowsheet included, three stages of crushing, conventional rod and ball mill grinding in series, and sequential flotation of four products utilising conventional mechanical flotation cells. To improve the profitability of the project the partners commenced a search for ways to reduce the projected capital and operating costs of the proposed development. This paper presents the improvements in the projected capital and operating costs as a result of design and concept changes. The major changes included: ò the simplification of the crushing section with the adoption of semi autogenous grinding (SAG) milling of primary crushed ore. ò the deferral of pyrite and barite flotation circuits until market conditions were positive. ò the simplification of the flotation circuit by the use of column flotation cells for combined rougher/cleaner duty. ò the purchase of second hand equipment. The result of these changes was to reduce the capital cost estimate of the plant from US$ 21 million to US$ 11 million and operating cost estimates from US$ 18.90 to US$ 13.60 per tonne of ore for a decrease of approximately ten per cent in potential revenues.

Jan 1, 1991