Search Documents

ALTHOUGH the mineral Stannite (Cu2S, FeS, SnS2 , also known as "bell 'metal" ore, tin pyrites, etc.) is found in various parts of the world, in only three iocalities has development proved it to exist in sufficient quantity to warrant the erection of treatment plants. Two of those mines are in New South Wales and one is an Tasmania. The writer will deal with the latter-the Conah mine, Zeehan, Tasmania, it being the most important and extensive occurrence so far worked. The Conah mine was first worked by a Tasmanian company for silver-Iead, and was fairly remunerative until the zone of secondary enrichment was passed through, when the lodes became too poor for further exploitation. During the time that the line was thus operated the stannite lode was discovered. It occurs in a graphitic slate, which, in common with the slates and spilites of the Zeehan field, is probably underlain by the stanniferous granite which outcrops two miles to the west. The Conah stannite lode is older than the galena lodes of the district, being faulted by one of the latter. Near the surface the lode was very rich.Shipments were sent out assaying 150 oz. of silver per ton, 20% copper, and 18% tin. An .apparently homogeneous sample of stannite, analyzed by the writer for the Tasmanian Geological survey, gave the following results:

Jan 1, 1915

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

By D Alexander

For nearly 100 years, the flotation plant metallurgist has often wondered what is happening æbeneath the frothÆ. To assist in unravelling this mystery, new technology has been developed as part of the Australian Mineral Industries Research Association (AMIRA) P9 project, to measure gas dispersion characteristics (such as gas hold-up, superficial gas velocity and bubble size) in industrial flotation cells. These measurements have been conducted in a large number of cells of different types and sizes by researchers from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. A large database has been developed and the contents of this database are described in this paper. Typical cell characterisation measurements show a wide spread in values, even in the same cell types and sizes performing similar duties. In conventional flotation cells, the typical gas hold-up values range from 3 - 20 per cent, bubble sizes range between 1 and 2 mm, and superficial gas velocity ranges from 1 to 2.5 cm/s. The ranges of cell characterisation measurements given in this paper will enable plant personnel to compare their operation to other similar types of operations from around Australia and the rest of the world, giving opportunities for further improvement to flotation plant operations.

Jan 1, 2005

AustraliaÆs record-breaking drought, efforts towards environmental best practice and the current commodities boom is demanding water use and reuse as never before. Mining practices, processing, the remote communities and support industries require vast amounts of specific quality water. Sustainability of water use has been a key factor in mine development, expansion of existing operations and increasing profitability of processes involving water. Developments in water treatment technology have enabled the use of a range of processes to produce this water reliably at ever decreasing costs. This increasing acceptance of new technologies has seen seawater desalination, recycling of plant wastewater streams, municipal wastewater reuse and others to become commonplace. Processes including seawater and groundwater reverse osmosis (RO), low pH RO, thermal desalination, high rate clarification, brine water treatment, ion exchange and other advanced treatment technologies are now used as part of mining operations. This paper surveys the trends in water treatment for the mining industry both in Australia and internationally with a review of technologies and case studies of operating plants. The key technologies are explained with an emphasis on the specific requirements for mining operations û unusual raw water, process and operations limitations, environmental concerns, as well as harsh climate. Case study information from several mining operations is included.

Jan 1, 2006

This paper provides a brief fundamental insight regarding the fabric media concept for liquor filtration. The subject matter will be of interest to metallurgists and engineers with professional responsibility for world class design of solid liquid separation processes and efficient lowest cost operation of existing mineral process plant. Avocet Mining commissioned the worldÆs first mineral liquor clarification process incorporating a fabric media liquor filter at their Lanut gold mine in Sulawesi, in 2004 with design consulting provided by the Australian company SLS Technology Pty Ltd. Development of the technology continues with applied research focused on selecting textile parameters to apply filtration to a wider range of particle and contaminant types, higher solids concentrations, and different process liquors. Liquor filtration with the Fabric Media technology offers an array of attractive benefits. For Avocet Mining, filtration of pregnant liquor directly from the heap leach pad has enabled removal of the sediment pond and sand filters from the traditional process flow sheet, thus providing significant cost and installation time savings. Avocet Mining has recently expressed confidence in the technology indicating selection preference of the technology for the expansion at Lanut and for a new project. The application design window for the Fabric Media concept is extremely flexible with the technology now successfully applied to many different liquor chemistries and application objectives around the world. Potential cost savings for solid liquid separation process plant, such as counter current decantation circuits, clarifier vessels and thickener tanks can be calculated from laboratory measurements or pilot plant demonstrations.

Jan 1, 2008

By L Richards, R L. Brathwaite, C Mazenga

Underground mining of gold-silver bearing quartz lodes was carried out in the great mines at Martha Hill, Waihi over 70 years from 1882 until 1952. Shafts and stopes reached a total depth of 600 m on 16 levels, with workings extending laterally some 1.6 km, and as new reefs were discovered the workings extended beneath parts of the township. Over their long life the mines produced 1217 tonnes of gold-silver bullion from processing 12.2 million tonnes of mined ore. In the early-1980s drilling proved large reserves of gold and silver ore remaining in stock-work zones between the previously mined lodes. This led to a new era of mining at Waihi with the opening of the Martha Hill open pit in 1988. A series of three sink holes have formed above unfilled stopes of the Royal lode. In 1999 a sudden collapse crater 40 m in diameter occurred near an occupied part of Waihi, placing in danger several houses and a busy street. This crater formed close to a similar crater that occurred in 1961. The 1999 collapse resulted in subsurface investigations and risk assessment studies being commissioned by the local Hauraki District Council. However, a further 50 m diameter collapse crater in December 2001 formed in a residential area, swallowing and wrecking an occupied house, fortunately without injuring its five occupants. Two other houses were perched on the crater rim. The 2001 collapse led to an acceleration of the work being carried out by the Institute of Geological and Nuclear Sciences Ltd. (GNS) to identify the extent of the old underground workings at Waihi. For the risk assessment detailed rock mechanics analyses were made to consider the stability of the underground mine stopes, in terms of the stope back, hangingwall, footwall and crown pillar failure mechanisms, as well as void migration. The collapse crater areas were analysed using using several methods, including analysis to simulate the probability of void migration from unfilled stopes to the surface using the @Risk program. The analyses show that in the cases of the actual collapse craters, the voids have a high probability of migrating to the surface, thus providing a method of testing the void migration modelling. Modelling analysis applied to the remaining stopes of the old underground mines show there are further areas where void migration from unfilled stopes has a high, medium and low probability of reaching the surface as a collapse crater. The locations of these probabilistic hazard zones were outlined using the @Risk modelling and deterministically by using the dimensions of the historical collapses applied along the length of the stopes. Consideration of the æincubation periodÆ (the time interval between the cessation of mining and the occurrence of collapse) and comparisons with mine subsidence histories overseas, indicates that further collapses are likely to occur over the next 50 years. Risk assessment estimates made using property values and occupancy levels within the three hazard zones, were compared with Societal and Individual Risk criteria. Results indicate that safety within the high and medium zones may be unacceptable.

Jan 1, 2003

By Mendeckl A. J

Anglo American Corporation has always viewed technological development as vital and as such has placed research and the implementation of new technological practices high on its priority list. Support is given to a number of research institutes but a significant degree of reliance is placed on in-house research carried out at individual companies and at the Group's main laboratory complexes. The Corporation's interests are diverse with advanced practices and innovative technology ranging from new battery technology with wide application to deep level shaft technology with very specific application. In this paper, we aim to concentrate on a particular system developed primarily for use in seismically active deep mines. The system has proved to have far wider application and has the potential to be further enhanced to meet the needs of users across a broad range within the industry and even beyond. As the nature of this conference is to inform delegates of advanced mining practices, we should simply mention that we could have talked on subjects relating to the advances made in deep level winding technology including winder drive and brake control to alleviate dynamic rope loads, shaft steel design for high pay load high speed winding and shaft safety systems such as slack rope devices and moving lip loading facilities to cater for rope stretch. Other areas of interest relating to refrigeration using ice technology or non-explosive rock cutting using diamond wire or saw technology could also have been of interest. As the South African gold mines become deeper and the problems associated with depth become more acute, answers had to be found and systems developed to cope with very high rock stress and the related seismicity. The fundamental understanding of the behaviour of the rock mass has always been important but became critical on our mines to ensure the safe extraction of the orebody. Basic research into and the application of physics, applied mathematics, seismology, rock mechanics, electronics and computer technology have helped us to develop the Integrated Seismic System - Integrated because of the system's abilty to monitor seismic and non-seismic sensors simultaneously and because it encompasses data acquisition, processing and interpretation into one system. The system which is in use at all our gold mines has found application not only in South Africa but also in such locations as Australia, Chile, Canada, Europe and Japan. A highly motivated team of scientists under the leadership of Aleksander Mendecki developed the majority of the hardware and software needed for the system. In essence, the system allows us real time monitoring of energy release and stress transfer data that with the aid of modern computers is turned into useful information. The information so obtained has allowed us to improve our mine and extraction designs to minimise the inherent hazards. The system has proved to be an extremely useful management tool as substantiated by the demand for the product. The paper is intended to convey to the reader the technical concepts and the presentation is intended to demonstrate the usefulness of the system.

Jan 1, 1995

By Burman B. C

This paper describes studies into two particular aspects of the Lochiel deposit which formed part of feasibility level geot2chnical and hydrogeological investigations for proposed open cut mine development. The two aspects were depressurisation of thick beds of silt located through the profile and the determination of characteristics and origins of soil structure and their effect on pit stability. The studies were very detailed and multi disciplinary and highlight the integration of geology, geotechnics, hydrogeology and mining that is required for mine development studies. It is considered that as more marginal deposits are developed throughout the world the demands for efficient economic mining together with in- creasing scales of operation will require simi- lar types of studies. As such the studies pre- sented herein are likely to be a forerunner to a,emerging trend for development of open pit mines in difficult ground and water conditions.

Jan 1, 1986

By Grobler H. P, Chitombo G. R

Production blasting of Dc Beers Consolidated Mines Limited, Koffiefontein and Finsch Mines involves both uphole trough rings of 9 to I I holes and near vertical 360 degree compound rings of 42-54 holes. The rate of production from these stages is dependent upon being able to achieve a specified fragmentation size range and this has driven the derivation of blasting practices to consistently achieve this target fragmentation. At the Dutoitspan Mine, in Kimberley, where mining of the kimberlite pipe is by block caving, 100 per cent extraction of the undercut level by ring blasting is essential. If this is not achieved, pillars are formed which not only inhibit the efficient initiation of the caving process, but also concentrates load onto the extraction level, causing damage to draw points and pillars. These two case studies demonstrate the importance of achieving optimum blasting performance for downstream mining efficiency; ie fragmentation for increased productivity at Koffiefontein Mine and 100 per cent undercut extraction for efficient initiation of the caving process at the Dutoitspan Mine. The case studies also serve to highlight the long road towards blast optimisation taken by De Beers Consolidated Mines Ltd (Koffiefontein. Finsch, Premier and Kimberley Mines) since 1989.

Jan 1, 1995

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance determined using an under-belt capacitance sensor in which a fringing electric field Interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal.A plant trial of the technique was conducted at Stockton Borehole Colliery, SW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7 - 14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the onbelt gauge.

Jan 1, 1989

By R K. W Merkle, E Whiteman

The anorthosite complexes and related rock types of the Indian Precambrian shield are primarily associated with either cratons or mobile belts. They were metamorphosed under amphibolite to granulite facies conditions. The major rock types are chromite-bearing meta-anorthosites, amphibolites, basic granulites, pink granites and gneisses. This study was carried out on chromitite bearing samples from Sittampundi Anorthosite Complex (SAC), Tamil Nadu, to evaluate the nature and textural settings of platinum-group minerals (PGM), using state-of-the-art technology. The structure and petrology of SAC were well studied by earlier workers (Subramanian, 1956), but only scanty data on geochemical, petrology and mineralogy of PGM are available. The mineralogy of the samples is dominated by chromite (>70 mass per cent), plagioclase (An90) and chlorite-actinolite with orthopyroxene (En85). Details of the petrological evolution of the Sittampundi complex will still have to be studied further, but indications of magma replenishment at the level of chromite formation and the elevated PGE values associated with the chromitite samples make the Sittampundi complex a promising target for future exploration activity.

Jan 1, 2008

By C McIntosh, M Carder, P M. J Durance

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Disseminated, gold-bearing sulfide minerals hosted in sheared, wall rock metasediments and clay alteration zones comprise one of the dominant styles of Palaeozoic orogenic gold mineralisation within the Reefton Goldfield, and is exemplified by OceanaGold’s Globe Mine. This study begins the exploration and characterisation of the gold-arsenic-antimony mineralisation hosted within the dominant lithologies of the Globe-Progress shear zone. The main gold-bearing sulfides are pyrite, arsenopyrite and stibnite. Pyrite and arsenopyrite are not compositionally uniform across the Globe-Progress shear zone. Pyrite from the mineralised greywacke and argillite has higher As contents than pyrite in the host rock and pug breccia. Furthermore, the mineralised greywacke and argillite pyrite are enriched in As from core to rim. The 3D models based on bulk assays reveal a significant correlation in the distribution of Au, As and Sb. The interpolant for Sb envelops those for Au and As, which in turn are very similar to each other in their vertical and lateral extents across the shear zone. This result is consistent with earlier findings that the occurrence of stibnite represents a separate and likely later phase of mineralisation relative to that represented by the formation of disseminated pyrite and arsenopyrite both of which exert a stronger control on the distribution of As.CITATION:Durance, P M J, Christie, A B, McIntosh, C and Carder, M, 2015. The composition of disseminated, gold-bearing sulfides within the three-dimensional framework of bulk Au, As and Sb in the Globe-Progress orogenic gold deposit, Reefton Goldfield, New Zealand, in Proceedings PACRIM 2015 Congress, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The discovery of gold mineralization at the Manhattan mercury mine, Napa and Yolo counties, California in 1978 was the result of applying a new exploration ore deposit model in a region previously unprospected for gold. This discovery, the McLaughlin gold mine, owned and operated by Home-stake Mining Company, is a classic epithermal mercury-hot springs-gold deposit currently producing approximately 7,776,000 grams of gold annually.The exploration program that led to this discovery was based on a mercury-hot springs-gold genetic model. The model was developed using basic knowledge of ore-forming processes plus careful field observations made during examination of many known precious metal districts in. the Western U.S.A. Theoretically, hot spring systems could host gold deposits and, indeed, gold in these environments had been recognized for years. However, at the time of the McLaughlin discovery, it was not known to occur in sufficient quantities to inspire geologists to explore hot spring systems specifically for gold. Field observations recognized the presence of hot spring deposits and mercury mineralization asso-ciated with precious metal districts, (Bodie, California being a type example), and this associ-ation prompted the development of a hypothetical model. Subsequent exploration activities were directed towards the examination of mercury mines and prospects as potential targets for gold deposits. The model envisioned hot spring deposits (sinter) containing mercury mineralization at the surface with anomalous gold values grading downward into significant ore grade gold values.

Jan 1, 1990

Epithermal deposits have been defined as the lower temperature end of a spectrum of hydrothermal mineral deposits and are inferred to have formed near the EarthÆs surface. The preservation of an epithermal gold deposit in an Archaean craton is rather problematic, especially when such deposits form clusters or groups as reported for the Pilbara and Yilgarn cratons. For two of the better studied examples of epithermal gold deposits in these cratons, Becher and Wiluna, the evidence that they formed near the Earth surface is non-diagnostic, and the epithermal origin appears uncertain. Despite the simplicity of the original definition, there have been numerous errors in classifying epithermal gold deposits. It is suggested that these errors are primarily due to poor criteria defining the group as there is limited evidence of poor observational science being the cause. The criteria being used to recognise epithermal gold deposits include tectonic setting, ore element suite and quartz vein textures. None of these are diagnostic of epithermal deposits and their link back to the original low pressure-temperature definition of the class is tenuous. There has been definition creep over time as new observations on potential epithermal gold deposits become accommodated within a flexible definition. There is some urgency establishing and then using criteria to reliably identify epithermal deposits. Distinction of epithermal gold from weathered gold deposits is an important step. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By McKendry J. B

Gretley Colliery is situated at Wallsend, a suburb of Newcastle in New South Wales and is owned and operated by the Newcastle Wallsend Coal Ccnpany, a wholly owned subsidiary of Peko Wallsend Limited. The mine has been an efficient bord and pillar producer by industry standards. However, its continued economic viability was threatened because the bulk of remaining reserves lie in more difficult mining conditions and are of poorer quality. Alternatives were examined to improve productivity and allow Gretley to become more competitive in the current difficult market Environment.

Jan 1, 1988

The capabilities of the three 61R and one 81R Robbins Raiseborers currently in use at Mount Isa are defined. Their applications in the development of ventilation and hoisting shafts, orepasses, escape routes, fill passes etc. are described and possible future uses of these and newer raiseborers at Mount Isa are examined. Problems associated with the use of raiseborers, together with ways of overcoming them are discussed. The impact of raiseborers on the mining operation is assessed in terms of new approaches to design and development, safety, cost and manpower efficiencies.

Jan 1, 1974

Wheal Gawler was Australia's first metal mine. This leader was followed by an army of other metalliferous underground mines and surface operations in Australia. As a mine it was not highly significant economically because its small total production of nearly pure galena had low multiplier effects on the economy of South Aus- tralia. Its importance lay in its symbolism: here was a silver-lead mine close to the new town of Adelaide posing the question of what other min- erals lay in the Mount Lofty ranges and in the fields beyond.

Jan 1, 1987

During the last two decades, restrictions on access to land for mineral exploration and development in Australia have intensified. State and Federal legislation relating to Aboriginal land rights, national parks, marine parks, wilderness areas and other conservation areas, the surface rights of farmers in New South Wales and Western Australia, national, State and world heritage, urban developments and acquisition of land by governments for other purposes have all placed limits on mineral exploration and mine development activity. More than 20% of Australia's land area is now either unavailable for mineral exploration or available only under severe constraints. Access to this land is denied at a significant economic cost to the Australian community. There have been few attempts to quantify this cost. More importantly these restrictions have developed on an ad hoc basis promoted by single interest government departments often with little regard for rational land use planning. The mining industry has embraced the community's conservation ethic and accepted that conservation areas should be set aside and that within those areas mineral activity should be restricted. In some cases the restrictions on exploration near areas of outstanding scientific, historical, archeological or scenic importance may amount to an effective prohibition. The industry has vigorously opposed the exclusion of mineral activity in conservation areas on purely emotive grounds, unsupported by scientific evidence and in disregard of land use potential, consideration of multiple use potential or consultation with existing or potential land users likely to be effected.

Jan 1, 1987

Coal mining in the Bulli seam in the Southern Coalfield in New South Wales has experienced the dangers of outbursts of coal and gas. These incidents present a major risk to the safety of mine workers and consequently a threat to the overall viability of the mining operations. Since the occurrence of a major outburst incident in the South Bulli Colliery in 1991 involving three fatalities, the primary contributory factors associated with coal/gas outbursts in the Bulli coal seam have been identified and a strategy for the management of the outburst risk has been formulated by the cooperation of mine operators, mine workers and the Department of Mineral Resources. Utilisation of risk management techniques in combination with modern gas drainage technologies and geological control methods have led to the formation of this effective outburst management plan. Clause 15 of the Coal Mines (Underground) Regulation 1999 in NSW has made it mandatory in an area of outburst to carry out mining in accordance with a code or guidelines developed for mining in outburst prone areas (DMR, 1999). In this paper an outburst management system is discussed which was developed for collieries in the Southern Coalfield that brings together all the available information including past experiences and risk management techniques in a documented form in order to maximise safety of mine workers. It is concluded that since the introduction of the outburst risk management systems in the Southern Coalfield in 1994 considerable reduction in outburst incidences have been experienced.

Jan 1, 2003

A number of gases, such as carbon dioxide, methane, water vapour, nitrous oxide, ozone and chlorofluorocarbons are transparent to incoming short-wave radiation, but are relatively opaque to outgoing longwave radiation. Variations in the concentration of these gases in the troposphere can alter the thermal balance of the earth's atmosphere. Outgoing terrestrial radiation which would otherwise escape to space, is trapped within the inner layer of the atmosphere, resulting in a greenhouse effect. It is estimated that at present greenhouse gases other than carbon dioxide, contribute about 50% to the greenhouse effect. However, in the future, the contribution made to the greenhouse effect by gases other than C02 will become increasingly more significant. Greenhouse gases arise from a wide range of sources and their escalating increease is largely related to an increase in the world's population, an increase in the standard of living of many areas and changes in lifestyle. The effect of increasing man-made greenhouse gases in the troposphere is unknown but it is proposed that it may increase temperature and may modify climate, agricultural response and land use. The sources of greenhouse gases are identified and found to comprise a wide range of activities. The contribution that coals use makes to the greenhouse effect is examined in detail. It is concluded that coals total contribution is small being about 10% of man made greenhouse gases. Envisaged expansion of coal's use will only cause a small increase in greenhouse gas emissions. Whilst developing technology for coal's use for power generation has the potential to reduce greenhouse gas emissions from new plants by approximately 25%.

Jan 1, 1989