Search Documents

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By Phillips RN

Semi-confined, trachy-andesite sills which overlie the German Creek Seam, within the critical tensile strain zone, form major groundwater hazards to longwall mining at the German Creek underground mines. The water contained in these aquifers is normally neutral, but highly saline. Techniques used to detect aquifers include routine air-lift pumping in exploratory drill holes, downhole geophysical and geological logging and upstage packer testing. Hydraulic constants are calculated from pump-out and pump-in test results. Hydraulic parameters for the calculation of mine inflow rates are determined from pump-out test results because these tests appear to be more representative of aquifer drainage during goat dewatering than pump- in testing. During mining of the first longwall block at Central Colliery, caving fractures intersected overlying aquifers after the longwall had retreated 40m, and mine water inflow rate rapidly increased from less than one litre/sec to 25 litres/sec. The amount of water pumped out of the mine during first panel extraction was 140 megalitres with drawdown occurring over an area of 168 hectares. In the Southern Colliery area approximately 324 megalitres of highly saline water which is actively stored in the Aquila Sill area will be pre-drained from six well points prior to longwall mining. With effective pre-drainage from surface drill holes, maximum inflow rate into the mine during initial goafing can be reduced from 165 litres/sec to about 45 litres/sec.

Jan 1, 1988

By Meakins R. L, Talaska A, Kenny D, Haycraft J. A, Dickson B. L

A vehicle-mounted radiation detector interfaced to a microprocessor called PRAM (programmable radioactive analyser mobile) has been developed to provide grade control for selective mining of a soft rock uranium ore. The grade of ore over which the vehicle passes is determined and indicated by several coloured lights to a pegman who walks behind the vehicle. Coloured pegs are then laid out to mark the uranium grade ranges on the floor of the mine pit. Comparison between grade ranges determined by the PRAM and by prior drilling and downhole logging at the Yeelirrie deposit, Western Australia indicate good agreement. Use of the PRAM decreases the cost, manpower and time required to grade extensive areas of a mine pit floor.

Jan 1, 1982

By Watsford R. M S, Hutton R

Following the delineation of significant extra ore reserves during 1990, the decision was made to expand production from 350,000 tonnes of run of mine ore per year to initially 600,000 tonnes increasing to 750,000 tonnes per year. The existing plant consists of a conventional three stage crushing plant followed by a heavy medium separation plant that produces a product prior to grinding. Grinding is conducted in three stages of ball mill in series. Alternatives examined for expanding production included: aò SAG mill - ball mill circuit replacing the secondary and tertiary stages of crushing, the heavy medium plant and the existing ball mills; and, upgrading of the existing circuit configuration.

Jan 1, 1991

By Daoust G, Dubois JF

The optimal sequence of decisions on rates of production and cutoff grades is obtained by a dynamic programming model. The main parameters are : 1. the size of the deposit, average grades and grade distributions, 2. the operating costs of mining and concentration, 3. the investments in mine and mill, 4. the smelter charge, 5. the price(s) of the metal, 6. the recovery and the grade of the concentrate, 7. the rate of interest, 8. the taxation formulae, 9. the upper limit to rate and the rate interval and 10. the upper and lower limits to cutoff and the cutoff interval. An amount of ore can be mined at various rates while applying various cutoff grades. It is assumed that a decision to mine at a certain rate during a period conducts to a certain state regardless of the cutoff grade. This assumption which is valid for several

Jan 1, 1977

The Proterozoic Pb-Zn deposits of the Gulf of Carpentaria, Australia, include HYC (McArthur River), Mt. Isa, Dugald River, Lady Loretta and Hilton. Two seamingly incom- patible depositional models have been proposed to account for their origin. Finlow-Bates (1980), Large (1983) and Russell(1983) classify these-deposits as sediment-hosted submarine exhalative deposits. This class includes Rammelsberg, Meggen, Silvermines, Sullivan and others. In contrast, a lacus- trine, shallow-water origin has been advocated by Williams and Logan (1981), Logan and Williams (1984), Muir (1983) and Eugster (1985). The discrepancies between these two models can be removed by creating a separate class, that of continental sediment-hosted exhalative deposits.. HYC., Mt. Isa and Dugald belong to this class and their sediments were deposited in shallow, alkaline lakes. Metal- rich, hot, Na-Ca-Cl brines entered the basins along boundary faults and interacted with pore fluids and sediments, depositing-Cu-Zn-Pb sul- fides. Similar brines entered the Lady Loretta basin after marine flooding, depositing sulfi- des and barite, placing Lady Loretta into the class of marine Sedex deposits.

Jan 1, 1987

Pyrrhotite is pyrophoric when in a finely divided form. The problems of disposing of large quantities of finely divided pyrrhotite separated out by metallurgical processing from ore are formidable. In the case of an underground mine, a solution to the problem of disposal is to place the pyrrhotite in the stoped out areas and seal from any air supply. Further, the pyrrhotite could be diluted with tailings which would reduce the possibility of combust- ion. Several enquiries to various centres and authorities have shown that the products of the slow oxidation of pyrrhotite with moisture present can cement an inert matrix into a stable fill similar in physical prop- erties to fill stabilised with Portland cement. Stabilised fill can be used to advan tage with a suitable mining method to provide high recovery. The investigation demonstrated that air and 15% w/w water must be present for the fill to harden and that the sizing of the particles is a critical factor in drainage of a hydraul- ically placed fill and subsequent even harden- ing of the fill in a stope. With the materials used in the experiments in which the - 51 micron component of the tailings had been dis- carded, an optimum mix was found to contain 4:1 tailings/slag ratio and an overall pyrr hotite concentration of 8% (all proportion by weight). Approximately 34 days after drain- age to 15% moisture in natural air flow condit- ions, an unconfined compressive strength of 1.862 MPa was attained. A subsequent experi- ment was conducted with a sample of optimum mix in a pipe one metre long in forced air flow conditions. At a superficial velocity of 3.Om per hour the mix required 155 hours to harden to 1.862 MPa after drainage to 15% w/w moisture content. The pressure drop bet- ween the top and bottom of the mix in the pipe remained constant at 9 KPa/metre length. This result suggests that forced air flow conditions will increase the rate of hardening. No dangerous effluents were detected in the course of the experiments which could affect mine equipment or personnel.

Jan 1, 1973

By M Pratt

For up to 75 years large scale coal mining has been carried out within the Latrobe Valley region of Victoria. Withdrawal of groundwater from Tertiary aged sediments within the Latrobe Valley is essential to allow coal mining to proceed to depth. Water within the overburden layers, coal seams and interseams must be drained to avoid flooding during the mining process. The pressure in deeper aquifers must also be lowered to avoid floor heave, batter instability, and to maintain safe operating conditions as the mines develop in size and depth. The cost-effective management of the groundwater systems at and adjacent to the mining operations in the Latrobe Valley is essential to enable the efficient utilisation of the coal resource whilst minimising the environmental impact of this major industry in rural Victoria. Large-scale depressurisation and dewatering programs within the Latrobe Valley mines are managed through the use of detailed groundwater management plans. These incorporate:an extensive monitoring network which extends up to 60 kilometres from the mines; detailed mine scale and regional groundwater and hydrogeological models; and established operational procedures aimed at minimising capital and operational costs associated with the mine groundwater systems. Groundwater extraction system optimisation programs have been introduced into two of the mines with the aim of reducing extraction rates, improved risk management, and reducing operational costs by approximately whilst not compromising mine safety. This paper reviews the aquifer depressurisation and mine dewatering operations of the Latrobe Valley mines and illustrates the techniques utilised to ensure that high artesian pressures do not adversely impact on the mining operations.

Jan 1, 2003

By P A. Williams, P Leverett

Many of the worldÆs stibnite deposits are found in orogenic zones and are mesothermal or epithermal in origin. They commonly occur near contacts between intrusives and metasediments. However, the spatial extent of anomalous Sb levels around such deposits is not well documented. This project has aimed to gain a better understanding of the mineralogy and geochemistry of Sb by deriving solubility and thermochemical data for some of the most common secondary Sb minerals. This has then been applied in field exploration for Sb ore deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Satayev IS, Shepelev DV

Various ways for applying the X-ray fluorescent method to process lump-by lump separation of secondary aluminium raw materials (scrap, slags, waste) as well as ferrosilicon and ferrochromium are being considered and physically demonstrated. A commercial X-ray radiometric sorter has been developed for processing secondary raw materials. Marketable quantities of aluminium scrap with appropriate copper and zinc content have been produced for smelting with a minimal additional of pure aluminium. An industrial complex for scrap processing, incorporating two X-ray radiometric sorters from the Hammermils company is successfully operating at one of the works in Russia.

Jan 1, 1993

The last decade of national water reform implementation has improved the availability and efficiency of water source allocation in Western Australia. However, it is critical to recognise that the concurrent mining boom witnessed the approach of full water allocation limits, and increasing trends in mineral processing, water infrastructure costs, and wastewater management costs. Water supplies are commonly viewed as absolutely critical to project feasibility in mining, industrial and energy generation projects, even if considered 'non-core business'.   An increasing density of mining projects and industrial estates in Western Australia (WA) creates an opportunity for water infrastructure cost sharing and synergies. The WA government and its agencies have given preliminary consideration to the establishment of independent water utilities in the goldfields (Kalgoorlie), the Pilbara, and Collie regions, and in the Kwinana Industrial Area. The impending Oakajee industrial area and Mid West regional development, and Anketell port in the East Pilbara, could also be considered for common non-municipal water supplies.   The critical issue of apparent commercial risk due to the large scale of water demands and the low customer numbers in the minerals sector relative to other water markets is expected to mandate government partnership in any non-municipal water utility ownership. The commercial feasibility risk is observed as a risk to water supply security for potential mining and industrial customers. Absence of proper water infrastructure planning and governance has the potential to create infrastructure access issues as observed for Pilbara rail developments under the Trade Practices Act 1974.   Other aspects of water cycle management which could be addressed by a non-municipal utility include resumption of mine dewatering water (required changes to WA legislation that are progressing) and consolidated wastewater management for maximising synergy or reuse opportunities and minimising cumulative environmental impacts.   Address of water infrastructure planning for non-municipal water demands must cover commercial and environmental sustainability outcomes to successfully progress minerals sector growth in the State.

Jun 1, 2010

Education and Training for the minerals industry has been identified as one of the key priorities by the AusIMM and many closely related groups. The AusIMM Education Taskforce has been engaged, through a visioning exercise, in evaluating what minerals education and training should look like by 2025. A common recurring theme is that for minerals education and training to be efficient and effective into the future, it needs to be comprehensive and inclusive. Some previous attempts to achieve efficiency and effectiveness have had limited success, mainly due to approaching the issues involved from a narrow, singular perspective. This paper outlines that the achievement of the desired outcome may require an approach that parallels the same techniques that are used for multi-dimensional mine planning, treating tertiary minerals education and training in a similar way to the planning involved for a complex orebody. Just as efficient and effective mine planning requires engagement and understanding of many factors, so too does engagement with tertiary minerals education and training. The major factors that need to be considered are outlined in the paper, including: levels of tertiary education and training; Australian Qualifications Framework (AQF), Levels 1 to 13: systems of minerals education and training, such as higher education, (mainly universities), industry/professional associations and licencing requirements, vocational education, (mainly TAFE) and workplace programs; types of minerals or mining methods involved; volume of delivery; stage in the flow sheet, (geology, mining, beneficiation, extraction, refining). For comprehensive mine planning there is the need to develop links or roadways and openings between different levels of a mine. Similarly, to achieve a comprehensive tertiary minerals education and training model, there is a need to develop pathways, recognition and credit transfer between the various levels and components of minerals tertiary education and training.

Jan 1, 2005

A system of decline mine entries and ore haulages has been designed for the Mt. Windarra mine. This choice was controlled by the nature of the ore- bodies, the mining method chosen and the capital cost of development re- quired for production. Mine entries are being driven 4 metres high and 5.5 metres wide and decline at 11%, to accommodate diesel haulage vehicles of 35 tonnes capacity. The.Mount Windarra haulage system and the design parameters used in its selection and design are discussed, and general design and selection parameters are proposed.

Jan 1, 1973

By Waghorn EP, Gleeson HB

The Loy Yang Optr, Cut is a brown coal mine bring developed in the Latrobe Valley region located some 160 kin south-east of Melbourne, Victoria. The mine has been designed to supply a mine mouth power station at a rate that will rise to 32 million tonnes per year by the mid 1990's. Continuous mining metnuds are employed using bucket Whtel excav- ators and conveyors. This paper describes the basis of the design of the Loy Yang continuous mining system ano cne experience of four years of initial operation.

Jan 1, 1987

By Postupack C

A major problem that has continued to plague the surface and underground coal industries is blast induced damage to the coal seam. Blasting Analysis International, in conjunction with a number of other organizations, has continued to address this concern through 14 years of field research in 68 full-scale production environments worldwide. Compiled results were obtained from varying field conditions. These included single and multiple seam coal mines, horizontal, rolling and steeply dipping coal seams and varied borehole diameters (ranging from 102 to 381 mm) and when using various explosive formulations. Results are discussed in detail along with the tools, test methods and analysis techniques to identify and quantify the problems. Over ten major causes of coal damage were identified. A number of practical and economic recommendations are presented that can benefit the entire coal and blasting industry especially in commercial operations whose economic growth relies heavily upon recovering an undamaged coal seam.

Jan 1, 1995

By J Morton

There are many avenues for potential liability facing the Mining Industry today. Liability for breaches of environmental statutes such as the Resource Management Act 1991 and the Hazardous Substances and New Organisms Act 1997 include not only financial penalties but imprisonment and perhaps even more significantly will affect the reputation of the Industry. The potential for liability is not restricted to the employees that cause the actÆs to which liability attaches, but also potentially affects all the levels of management and even the company itself. There is also potential for liability through common law actions which can be utilised in cases of environmental harm. These should not be ignored by the Mining Industry. The Mining Industry must take a proactive approach to minimise exposure to potential environmental liability. This can be achieved by undertaking comprehensive environmental management initiatives and policies.

Jan 1, 2005

By Ribicic M, Kocar F

Surface lakes or water accumulation present a possible threat for the flooding of the underground mining works. Therefore, the criteria that define the conditions under which no flooding of the mining works can occur are of vital interest to the miners. The authors present the criteria that they developed for the Velenje lignite mine, Yugoslavia, and that take into account the elastoplastic behaviour of the rocks and the natural stresses involved in the deformable strata between the bottom of the lakes and the mine works as well as the extent of the direct caving-in process resulting from longwall mining activity. Fi- nally a generalization of these criteria to the other rock and stress conditions is discussed.

Jan 1, 1988

By Casale G

This paper discusses a long range mine plan development at the Santa Fe Pacific Gold Twin Creeks Mine based on the reserves of Mega pit. The key constraints of the schedule development included two types of mill ore targets (sulphide and oxide mill ore), consideration of blending of six chemical constituents (sulphide sulphur, carbonate, organic carbon, the ratio of iron/[arsenic, antimony]), and mining of acid generating and acid neutralizing waste at pre-defined proportions. Solution approaches, selected results, and project experiences are discussed.

Jan 1, 1995

A programme began in 1970 to eliminate the charging of fine materials into the copper blast furnace of The Electrolytic Refining and Smelting Company of Australia Ltd. at Port Kembla, N.S.W. A disc pelletiser and drying plant has been installed as part of this programme. Feed material for the plant is a blended mixture of copper concentrates, fine copper-bearing residues, and blast furnace cyclone dust. The operating parameters for the disc have been calculated by comparing the perform- ance of three other discs on the plant. Re- search work on choice of binder, feed moisture and drying conditions has led to the production of reasonably high strength pellets. A description of the pellet plant and modifications necessary to overcome the initial performance problems is given.

Jan 1, 1974

By M Castle, D Mendelawitz

The Marra Mamba iron ore in FortescueÆs Chichester Range project area occurs as a very flat dipping series of waste shale and iron ore beddings. These beddings vary from millimetre thickness to several metres. The ore material generally exhibits a moderate degree of competence when subjected to ultimate compressive strength (UCS) tests, normally failing at up to 60 Mpa. However, the strength of the beddings is markedly less when subjected to the tensile forces imposed by the cutting action of the surface miner. Two surface miners of differing age and sizes were tested over a period of almost three months. These machines produced a product that had not been subjected to dilution by blasting and of such a size that primary crushing is not required. The machines were able to cut all ferrous material presented to them with varying degrees of success. Material containing higher quantities of manganese were broken but caused catastrophic wearing of the picks. During the trial the volume of material produced by the two machines in various strength materials very closely matched the manufacturerÆs estimates. The major impact on costs per tonne related to the wear on bits, which in turn varied with the bit design and composition. Bit design and composition testing is continuing.

Jan 1, 2007