Search Documents

The locality from where these specimens come is distant about 12 miles due south from the township of Bingara New South Wales, and is known locally as Carney's Reef, Barrack's Creek, Top Bingara. The formation traverses the western side of a serpentine spur from the main range, which runs through the country from the other side of Tamworth to Inverell, in the New England District. It has a due north and south trend, with an easterly underlay slightly out of the vertical. The formation has been opened up at different points for a distance of over two miles, and each place showing gold in the stone, and no place more than three to four chlins apart, the whole distance along the line of Reef being leased. The formation varies in thickness, the smallest being about 1 foot and the widest about 10 feet. The following is a list of properties, and description of work done on them at present. First south, and about one and a half miles from Hanion Brothers' old BalIarat claim due north, Court and patty hold a tenacre lease. The formation outcrops near the south boundary, and gold is obtainable in the stone. In the centre of the lease a costeen pit has cut the capping, which shows gold, and about two chains from the north boundary another one cuts the capping, also showing gold. The reef averages, where exposed on this property, 3 feet wide.

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

The unique characteristics of the Target orebody and modernistic approach to mining present significant challenges and a concomitant high potential for new opportunities. The break-away from the traditional labour intensive mining methods improves both safety and productivity significantly. The intention of the paper is to illustrate the application of well known mining methods to the particular requirements of a complex orebody at depth. The evolutionary process followed to establish the final mining method design provides insight behind the finished product, and the modern approach to the planning and service principles equips the reader with a suite of mining engineering ideas.

Jan 1, 2000

By Ellicott C, Webb N

In November 1996 the NSW Minister for Mineral Resources, Hon Bob Martin MP, commissioned ACiL Economics and Policy Pty Ltd to conduct a wide ranging review of safety within the New South Wales mining industry.The review was a response to a disturbing number of fatalities which had occurred in the industry during the Minister's term of office together with a number of alarming near misses where serious failures in mining systems had occurred. Shortly after the review was commissioned, four mine workers died at Gretley Colliery near Newcastle. An inquiry is currently being conducted into the incident.

Jan 1, 1998

By X Hu, J Björkvall, L Sundqvist Ökvist

The metal production industry is a significant contributor to global CO2 emissions due to the use of fossil fuels such as coal and coke. To mitigate these emissions and meet climate goals, innovative and sustainable technologies are required. Molten salt electrolysis is a promising technology that directly produces metals from their precursor sulfides or oxides using electricity. When combined with renewable electricity and an inert anode, the electrolysis process can be carbon neutral. This paper presents the results of two pilot-scale studies on the electrolytic reduction of metal oxides and sulfides in molten salts. The first study focuses on the electrolytic reduction of chalcopyrite in molten NaCl-KCl salt. The results demonstrate that in situ separation of copper, iron, and sulfur is possible, enabling the extraction of all valuable elements without CO2 emissions. Furthermore, the findings underscore the capability to eliminate impurities like zinc, antimony, arsenic, and mercury from the electrolysis product. The second study investigates the electrolytic reduction of pure/synthetic chemicals of wüstite, hematite, and magnetite, as well as a magnetite-type iron ore in molten NaOH salt. The findings reveal a stepwise reduction of iron oxides from high valence to low valence, ultimately leading to the production of metallic iron electrolytically. Notably, this study underscores the challenges associated with the selection of an economically viable and durable inert anode material for efficient oxygen generation. These results indicate that molten salt electrolysis provides a sustainable and green route for base metal production. The use of this technology has the potential to significantly reduce CO2 emissions in the metal production industry, contributing to achieving climate goals.

Jun 19, 2024

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

Grinding is probably the single unit operation that requires the largest capital investment and operating costs in an ore beneficiation plant. Because of that, a great deal of research has been concentrated in the theory, design and operation of grinding equipment, in particular ball mills. To-date, the models developed to describe grinding in tubular mills are macrophenomenological and can be divided into two categories: energetic and kinetic models. This paper presents a new approach to modelling ball mill grinding: The Operational Model. The theoretical aspects of the model as well as a comparison with existing ones are discussed. The concepts of the model, summarised in easy-to-operate PC programs, permit the calculation and design of new ball mills, and a critical evaluation and optimising of mills in operation.

Jan 1, 1993

In most States of Australia it is a legislative requirement for underground mines to have a separate means of egress from the normal means of ingress to permit the safe evacuation of workers to the surface in event of an emergency. Such egress may be in the form of a ladderway equipped shaft/underlie or trafficable incline/decline. Additionally, there is a general requirement to have one or more airways, separate to the main shaft or other principal entrance of an underground mine, extending to the lowest level to permit ventilation to all parts of the mine. Fulfilling these requirement is difficult in the development phase of a mine when access underground is achievable by only a shaft or decline in the process by being sunk. What is frequently practiced in Australia is for production to then commence, sometimes in association with continuing development, in the same configuration without the establishment of this separate method of egress to the surface nor additional airway/s with reliance on refuge chambers to cater for back up in any emergency. Not only, could this jeopardise the health and safety of workers in case of an underground emergency it could be construed as a statutory breach of legislation. While recognising that refuge chambers are often used throughout underground operations nowadays their equipping and the criteria for their location needs to be bought into focus. This presentation discusses how such legislative requirement can be met alongside the use and appropriateness of refuge chambers.

Jan 1, 1998

By X S. Li

The modern mechanical excavation machines have enough power for cutting hard rock. The ‘bottle neck’ which limits the use of machines for hard rock excavation is ‘cutting tool’. To cut hard and abrasive rock, CSIRO has been developing Super Material Abrasive Resistant Tools (SMART*CUT). SMART*CUT technology replaces the tungsten carbide (WC) tip of conventional pick with thermally stable diamond composite (TSDC) and attaches the TSDC tip to steel tool body with CSIRO worldwide patented bonding technology. This paper introduces the key features of SMART*CUT, compares its performance with conventional WC tipped tools, discusses the challenges faced by SMART*CUT and the further developments needed for successful application of SMART*CUT to mining industries.

Nov 22, 2011

By M L. Habner, S D. Munro

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

By Smith IEM

Some samples from arc-type volcanic suites collected in northern New Zealand and southeastern Papua New Guinea show rare earth element (REE) and Y abundances which are enriched relative to the those typical of their respective associations. This enrichment appears to be the result of an alteration process which selectively mobilises the REE and re-precipitates them as REE-bearing minerals in veins and interstitial patches. The alteration is on a micron scale and is not detected in routine petrographic examination. The spectre of REE mobility in young apparently fresh rocks is important to igneous geochemists who use REE abundances to constrain petrogenetic models and may also be important because it indicates the operation of a natural REE enrichment process which could operate in the formation of economic REE deposits.

Jan 1, 1990

By R A. Pax

Heavy machinery such as AG and SAG mills generate a significant amount of noise due to the processes that are occurring inside them. From an environmental perspective, the level of noise generated is a significant occupational safety hazard. However from a technical perspective the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of the primary comminution tumbling mills. Traditionally, the use of perfect mixing has been assumed when modelling the operation of AG/SAG mills. If this were true then the acoustic emissions from AG/SAG mills would be uniform along the length of the mill. Experimentally this has been found not to be the case. From another perspective it should not be the case because of the different conditions existing at the feed end compared to the discharge end. This paper presents the results determined by non-contact acoustics and their analysis in terms of understanding of the mechanisms occurring inside a mill.

Aug 8, 2011

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

Mechanical and electrical (M&E) systems in road tunnels are constrained by the traffic envelope and the construction profile. Whilst these spatial constraints are often ælocked inÆ early in the design process, the detailed M&E design continues for some considerable time after key civil engineering issues have been resolved. Ventilation design criteria for both normal and emergency operation often involves considerable negotiation with a wide range of stakeholders. Final system performance and spatial requirements are only finally resolved when suppliers are selected following the tender process. Lighting design is dependent upon a wide range of factors including tunnel lining materials and associated colours as well as agreed maintenance regimes. Cabling systems can only be developed when the general arrangement for power distribution is agreed and a system of substation, switchrooms and equipment rooms is in place. Many other systems such as fire protection and communications facilities fill the available space beyond the traffic envelope, where physical, structural and æsight lineÆ requirements must all be accommodated. The more co-ordinated civil engineering and M&E design is and the earlier the process starts the better the outcomes for all parties.

Jan 1, 1999

Independent assessments of existing and projected mining operations are often required in the exchange of assets and for raising capital, requirements which are particularly prevalent where there are new mining fields, a characteristic of the Pacific Rim area. Such audits and appraisals typically consist of a geological evaluation of the ore deposits; estimates of mineral inventories and mineable reserves; assessment of mine plans and costs; assessment of ore processing methods, recoveries, and costs; assessment of infrastructure and G&A (general and administrative) requirements and costs; assessment of environmental, permitting and reclamation requirements and costs; and, finally, economic evaluation based on various discount rates and metal prices. Audits provide a challenging task for consulting engineering companies, but one well worth the effort for mine developers and those connected with financing of the mining industry.

Jan 1, 1990

Studies of human relations are being made by a team of psychologists within management and in the community of Kambalda as a whole. Some of the first results are discussed with reference to extensions required in management when it also has to run a mining town. Implications are noted for town planning policies of the attitudes and preferences of the population with regard to housing and to other major planning areas. Some of the theoretical and practical difficulties of 'planning the human ecology' are outlined.

Jan 1, 1973

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

By Noble AC

Ore reserve reporting practices in the United States may be broken into four general categories as follows: ò Reserve reports, often of an unofficial and preliminary nature, which are made through the news media. These are often based on exploratory drilling or sampling results. ò Reserve reports made for the purpose of raising public funds by issuing securities on the stock market, or as part of other filings to the United States Securities and Exchange Commission. ò Reserve reports to obtain private funds from banks, financial institutions, or other investors. ò Reserve reports for internal use and planning by companies operating or evaluating mineral properties. This paper discusses current practices for each of these types of ore reserves reports and reviews recent changes which have affected those practices.

Jan 1, 1987

By Wheatley MR

Answers to the questions "which rocks contain diamonds?" and "which indicator minerals should diamond explorers look for?" are no longer so easily obtained, now that diamonds are known to occur in lamproites and various types of lamprophyres, as well as their traditional source of kimberlites. One way of isolating those factors (host-rock"geochemistry, geographical or tectonic location, xenolith minerals, etc.) which are most critical in determining the diamond potential of a given pipe, is a detailed and critical re-examination of the huge volumes of accumulated data on kimberlites, lamproites and related rocks. A large analytical database to this end has been set up on an Apple Macintosh II microcomputer using the quasi-relational database management system 4th Dimension. Currently, it contains data for up to 90 major and trace elements, isotopic ratios and contained mineral compositions for some 4,000 rock specimens from all over the world. Many experiences in setting up this database are probably relevant to other geologists setting up their own systems: they include determining the relationships between data items; the advantages of codes over free text in representing categorical variables such as rock types; the need for rigorous error trapping and data validation; and the problem of missing data values and ambiguities thereof. The working system is now being used in a rigorous statistical assessment of the criteria which distinguish diamondiferous from non-diamondiferous rocks.

Jan 1, 1989

By V N. Rudashevsky, N S. Rudashevsky

Characterisation of platinum-group element (PGE) deposits and their process products has many challenges for the process or applied mineralogist. It is now well established that the PGE distribution for such samples is variably divided between submicroscopic concentrations of PGE in sulfides, tellurides and related minerals occurring as discrete platinum-group minerals (PGM), of which there are a large number of species, many with partial replacement between the PGE and between anions. Each PGE deposit type requires a targeted approach but fundamentally, there are two general methodologies in vogue. One way is to make a large number of polished or polished thin sections for detailed scanning electron microscopy (SEM)/optical examination to determine the PGM distribution and their associations and grain sizes. The other is to make concentrates of representative crushed or processed samples, thus having fewer subsamples to examine. Our method of choice is to use hydroseparation (HS) for concentration. HS provides representative concentrates of sizes down to ~10 ¦m, not possible by other techniques. Various microbeam methods have been used for analysis of trace quantities of PGE (EPMA, micro-PIXE, SIMS and LAM-ICPMS). We prefer LAM-ICPMS (laser ablation microprobe û inductively coupled mass spectrometry) because of the relatively large analytical volume sampled, the ability to measure all the PGE, monitor up to 20 elements, together with detection levels in the tens to a few hundreds of ppb. We provide typical results derived in studies of stratiform PGE ores and tailings, and a massive Ni-Cu sulfide ore.

Jan 1, 2008