Search Documents

Potential hlghwaJl mining reserves in Australia are large, but geotechnical and operating conditions are quite different from those where highwall mining has evolved in the USA. In order to achieve safe and effective resource recovery, equipment and procedures should be developed to penetrate 250 m in the Australian mining environment. This paper identifies key auributes to be incorporated in such machinery and methodology. These suggestions are intended to promote discussion on innovations to satisfy Australian requirements for highly productive, safe and environmentally acceptable techniques.

Jan 1, 1993

R F Johnston 1 ABSTRACT The possibilities for bacterial leaching of refractory gold ores found in the Central Victorian region of Australia are examined. The behaviour of bacteria, especially 77iobacillus ferroaridans is outlined and the effects of these when they are exposed to pyrite, arsenopyrite and stibnite are examined. The factors which are particular to Central Victoria are outlined and the possibility of adapting a bacterial culture to suit the conditions is discussed. It is concluded that a bacterial leaching system is a feasible proposition and that it could enhance leaching rates and yields.

Jan 1, 1994

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998

By A Gibbs

Culture and leadership go hand in hand, especially when it comes to investing in safety. But the reality is that most safety leaders haven’t been taught the fundamental soft skills needed to lead effectively. In fact, only one in four safety leaders demonstrate effective skills and behaviours. Furthermore, when compared to its peers in other high-risk industries, our research indicates mining has the most room for improvement when it comes to effective safety leadership. In this presentation safety culture, climate and leadership will be outlined. Additionally, research data collected from our clients, across a variety of industries, will be shared to inspire reflection on the value of safety leadership. Finally, strategies to empower leaders and increase safety leadership behaviours will be described.

May 5, 2022

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

By Butler RD

The Singhbhum Copper Belt is an arcuate zone of verthrusting which extends over a strike length of about 180 kilometres, located in Eastern India, 150-300 kilometres west of Calcutta. The Belt is noted for its mineralisation, and both copper and uranium are currently being mined within it.

Jan 1, 1990

This paper presents a summary of tools and methods used for geotechnical assessments and monitoring systems at block caving mines. A critical review of these tools is given based on the authorÆs experience in block caving operations. The reviewed tools include cavability prediction, fragmentation evaluation, geotechnical monitoring systems, numerical stress analysis and others. Some of these tools have been developed under certain circumstances in particular mines and experience shows that their applications under different geological and mining conditions have often been difficult. Examples from block cave mines are also utilised in this paper to illustrate the importance of the further development of these tools, whilst possible improvements on these tools are also suggested.

Jan 1, 2000

By White A, Price G

The main assets of a mining company are its orebodies; the second are the people who find and use them.The graphs in Figure 1 were derived from a paper by Rob Macdonald of Rothschild Australia presented to The AusIMM Centenary Conference in Adelaide earlier this year. They show that the value of the industry on the Australian Stock Exchange halved over the past decade, despite the re-investment of capital equivalent to its full market capitalisation. Why is this so? The average dividend yields for the ASX Mining Index was never above five per cent during that period and barely averaged 2.5 per cent. Why then is $Ai million capital re-investment per employee since 1960 not enough to generate a rate of return to investors better than lousy bank interest? Do the investing public no longer regard our industry's assets to be world class?

Jan 1, 1993

By A He, J Li, J Pan, J Clout

The removal of sulfur from SO2 containing flue gas is improved by adsorbing SO2 into solution with manganese ions as catalyser, however, burnt lime slurry has to be added to modify solution pH and the CaSO3 by-product is of low economic value. In this paper a novel one step process for simultaneous manganese leaching-desulfurisation of flue gas is presented. An investigation of the effect of process parameters included flow rate and SO2 concentration in flue gas, adsorbing time, solution to solid mass ratio, leaching time, and their impact on the oxidation and removal of SO2 from flue gas. The catalysing mechanism of manganese ions on the oxidation and SO2 removal was demonstrated by calculation of the species originating from manganese ions and SO2 in the solution according to solution chemistry. SO2 removal in the adsorbing solution took place at pH 5 - 6, where manganese ions dominantly occurred as Mn2+, and the chain reactions for oxidation of SO2 starting from HSO3- were improved by the presence of Mn2+. SO2 bearing flue gas was effectively desulfurised by leaching rhodochrosite (MnCO3), with desulfurisation of the flue gas and modifying the solution pH being achieved simultaneously, and MnSO4 of high economic value recovered from the leachate. 85 per cent manganese leaching and over 70 per cent desulfurisation of the SO2-bearing flue gas were achieved with only one adsorption stage under optimum conditions.

Jan 1, 2004

By Di Pasquale S, Osler GD

Mount Isa Mines Limited recently commiss ioned an 800 tph Heavy Medium Preconcentration Plant for lead/zinc/silver ores. The decision to build this plant was made in late 1979 based largely on investigations conducted in the Company's pilot plant on a variety of ore types including Hilton ores, between 1972 and 1978. The paper reviews the historical develop- ment of the pilot plant heavy medium circuit through this period and illustrates the extent to which this work impacted on the final design criteria. This review also includes a description of plant operation, manning levels, process equipment and metallurgical performance Achieved.

Jan 1, 1978

By Smith I. K

A Data Acquisition System with a capacity to monitor 2000 analog instruments has been installed at the mines operated by the Zinc Lorporation, Limited and New broken hill Consolidated Limited (ZC/LVbHC), New South Wales, Australia. Since commissioning in March, 1982, the system has proved its value in providing up-to-date information to both Rock Mechanics and Mining personnel. The paper describes the function of the major software and hardware components of the system, and identifies the advantages that an on-line monitoring system provides in the day-to-day operation of a large underground mine.

Jan 1, 1983

The recommissioning of the plant at Mary Kathleen involved several distinct phases. The previous plant process was modified significantly, the plant capacity was increased by the addition of new equipment and the exist- ing equipment was in most cases overhauled. This equipment was either reused in its original duty or relocated. Maintenance requirements after the plant was cmommissioned were high because of the amount of modified equipment and also because some old items of equipment were deliberately not overhauled during recommissioning. The equipment that was overhauled has operated reliably. However some new equipment has not been as satisfactory.

Jan 1, 1978

By M, C A. RosiFre, R C. Figueiredo e Silva

Jaspilites and underlying basalt contacts of the Archaean volcano- sedimentary Grpo Parß Group, Carajßs, host giant iron mineralisation in the ~100-km long, E-W trending Carajßs fold. Preliminary, unpublished geochronological data point to a Palaeoproterozoic mineralisation event. Geochemically, jaspilites are typical volcanogenic banded iron formations. Basalts exhibit evidence of spilitic seawater interaction. Iron-associated hydrothermal alteration of mafic rocks was induced by fluid infiltration in amygdales, with development of chlorite- and hematite-dominated zones. In the case of jaspilites, iron mineralisation encompasses: partial replacement of jaspilitic microcrystalline hematite by blasts of martitic magnetite; jasper recrystallisation, producing fine-grained, hematite-free granoblastic quartz; martite recrystallisation, forming lobate¦subhedral hematite; pervasive porosity development by quartz-chert leaching; incipient cavity filling by microlamellar hematite; and advanced filling by coarser, euhedral and comb-textured, tabular- shaped hematite.Peak hydrothermal ore textures indicate typical epithermal-crust conditions, supported by preliminary fluid-inclusion calculations at 160 - 200¦C. Such temperatures and extreme fluid-to-rock ratios during alteration must have exceeded the ambient metamorphic conditions, with the infiltrating fluid relatively hot and capable of leaching SiO2. Therefore, mineralisation developed over exhumed, Archaean, brittly deformed rocks, with mineral associations representative of very low- to low-grade metamorphism. Considering that chlorite (¦talc) abounds in mafic rocks; hydrothermal albite is developed; dolomite fills veins and vugs; the typical rare-earth-element (REE) pattern of jaspilites is significantly modified in higher-grade hard hematite ores (higher LREE); pyrite, copper sulfide minerals and rare gold occur in association with carbonate-quartz-rich alteration zones, it is suggested that an alkaline, H2O-Fe-CO2 mineralising fluid dominated, also containing species like S¦Cu¦Au. Peak-mineralising conditions are likely to have resulted from a single, evolving fluid, via incipient- through advanced-stage alteration phases. The porous, high-grade soft hematite-type ore (SH), rich in microlamellar and anhedral hematite, must have derived from interaction with this relatively hot SiO2-leaching fluid, whereas the high-grade massive hard hematite-type ore (MH) developed due to closer fluid-rock temperature equilibrium conditions, attained by mineral reactions, with relative increase in the Fe/Σcations ratios allowing the precipitation of subhedral-tabular hematite that partially cements the soft-hematite ore. SH and MH hematite ore types must thus reflect intermediate and high fluid:rock ratios, respectively. Since the N5 deposit is to date understood to contain the largest amount of the MH ore, its units are interpreted as the loci of the highest fluid:rock ratios in the district. Preliminary mineralogical information regarding the S11 deposit of the Serra Sul (south range) implies higher-temperature conditions. The near-equant grain size and the granoblastic intergrain relationship, coupled with the presence of riebeckite, augitic pyroxene and garnet, suggest hornfels textures. The data collected, though still relatively sparse, permit the speculation that the immense driving force for the Carajßs world-class iron deposits was a relatively shallow, igneous-related hydrothermal system. If such a model is correct, then the Carajßs Palaeoproterozoic iron deposits could represent an end-member of the iron oxide-copper-gold hydrothermal system in the province.

Jan 1, 2005

Thank you and good morning. I am delighted to be here and to see so many of my colleagues and competitors. The general topic of this week's conference - World's Best Practice in Mining and Processing - suggests a focus on mining and processing. I am somewhat of a `jack of all trades and a master of none'. But I'm not even a jack when it comes to mining and processing technology and practices, and so I will leave those topics to speakers better 'qualified than I. Instead, what I would like to do is give you my thoughts on the best management practices of mining. You see, the times are changing for the mining business. There is great uncertainty in our industry. Anyone who received their education in an English-speaking school probably remembers the famous poem `Invictus' by William Ernest Henley. The two most famous lines from that poem are, if you remember, `I am the master of my fate; I am the captain of my soul'. The fact of the matter is that the metals industry, including the copper industry, is not the master of its fate. To a great extent we're at the mercy of forces over which we have little control, such as the world economy or political situations in individual countries. The copper industry is like a surfer at Manly - we can't influence where the wave is going; all we can do is stay in front of the curl and on our board. Historically, discovering, developing and processing ore reserves were the primary facets of our capital intensive business. To stay competitive today, we must invest equally in intellectual capital - our employees - in order to succeed in the face of economic, regulatory and political challenges and global competition (Schonberger, 1986). Everyone seems to have a different theory about being competitive. A lot of people use sports analogies when talking about competition. Others, like American businessman and former US presidential wanna-be Ross Perot, take a more interesting approach. In Mr Perot's hypothetical corporation, competition is a lot like having a snake in a factory. If someone sees a snake, the first thing they do is create a committee on snakes. Then, the committee on snakes meets and discusses the problem for a couple of years. The most likely course of action is nothing. Everyone figures that the snake hasn't bitten anyone yet, so they just let him crawl around the factory floor. Perhaps a vice president of serpentine affairs is appointed to continue watching the snake - making sure it doesn't grow. Ross Perot sees it a little differently. In his corporate world, business needs to build an environment where the first guy who sees the snake kills it. Of course in our industry, we better make sure the snake isn't on an Endangered Species List before we go after it! I am not going to talk about competition and competitive forces in terms of sports or snakes, but I would like to share some thoughts with you about how the mining industry can better utilise competitive thinking to get ahead and stay there. You may be wondering how an executive from a 160-year-old company could know much about competitive spirit, but the founding ancestors of Phelps Dodge were wizards at identifying

Jan 1, 1995

By Han Kook-Nam, Lawson F

The recoveries of the three cobalt minerals in the Mount Cobalt deposit, cobaltite CoAsS, erythrite CO3(AS04)8H20, and new cobalt mineral with a composition approximating 2CoO.CaO.Fe203.2As205.11H2O were investigated using physical and surface-chemical processes.Over 80 per cent cobalt recovery was achieved by tabling a cobaltite-mineralized sample, while about 76 per cent cobalt recovery was obtained by dry feed magnetic separation of a sample containing erythrite and the new cobalt mineral. The resultant primary magnetic concentrate with a cobalt grade of 5.5 per cent, was able to be upgraded to 14.4 per cent cobalt by regrinding .and a further magnetic separation.Electrophoretic mobility - pH responses for each of the three cobalt minerals were found to be similar. Each mineral remained negative over the pH range 3 to 11 and was most negative at mildly alkaline pH values.Cobaltite was floated effectively with amyl and ethyl xanthate collectors under acidic conditions at collector concentrations of 10-2M to 10-5M. Erythrite showed a similar flotation response using 10-sM amyl xanthate. The practical application of these laboratory separations to an industrial process is suggested.

Jan 1, 1976

In both surface and underground coal mines, the detection of geological structures ahead of workings is recognised as being fundamental to the efficient operation of the mine. Mining into zones of unexpected structures has a drastic effect on a mine's productivity. For the prediction of structures, geophysical methods can be applied from the air, from the ground surface, from boreholes and from underground workings. There are several improvements to report in the geophysical methods being developed for these purposes. These include developments in three-dimensional seismic reflection surveying, cross-hole seismic reflection methods and radar systems. The recent development of the radio imaging method for use in underground mine workings will complement existing in-seam seismic methods. Geophysical techniques for use in horizontal boreholes are also under development.

Jan 1, 1988

By Cottrell EC

Remote sensing has been used for many years but until recently its application has been limited by the resolution of the data available. High resolution airborne multi-spectral scanner data (MSS) has proven suitable for a number of applications including environmental management and monitoring. A shallow water mapping research. project completed on the Gold Coast has shown that- remote sensing can be used as a cost effective tool for environmental management and Monitoring.

Jan 1, 1987

By X Li, H Alehossein

The oscillating disc cutter (ODC) is an innovative technology for the continuous excavation of hard rock. This paper will discuss:the reasons for its development;its method of operation;current experimental results and mathematical modelling undertaken at the CMTE; andapplications in the mining and rock excavation industry.

Jan 1, 1999

The Ausmelt Catalytic Waste Converter (CWC) has been developed for use in the treatment of industrial wastes and for the recycling of secondary materials. Ausmelt Technology uses a top submerged lance system within a versatile and efficient slag bath reactor. High temperature pyrometallurgical reactions are carefully controlled within an oxidised molten siliceous slag such that metals can be extracted from waste feedstock for recycling, with non-volatile elements reporting to the slag, usually as oxides. Modification of the slag chemistry results in a final slag product that is stable, vitrified and is able to pass standard leach tests such that it is safe to discard or be used in civil engineering applications. Toxic components in the wastes such as organohalides can be completely destroyed and are prevented from reforming. Waste to energy conversion is practiced by the addition of a heat exchanger/steam generator in the converter offgas system. The Ausmelt CWC has been used for recovering zinc from residues and slags, treating spent potliner (SPL) from the aluminium industry and a wide range of electronic and other potentially valuable waste materials. Methods of monitoring the exhaust gases at different stages in the CWC gas handling system are discussed. The assay of these gases prior to emission is used to assist in the control of the converter chemistry to ensure the complete oxidative breakdown of the feedstock.

Jan 1, 2002

By Coxhead B. A, Brandt B. A

The geological exploration and evaluation of coal reserves involves the appraisal of very large amounts of data. Computers afford an ideal means of handling and manipulating the data, thereby avoiding the laborious and expensive method of manually compiling the logs in full descriptive language. The Minad system of computer storage and retrieval of geological and analytical data is particularly suited to the description of cores and cuttings from exploration drill-holes. The encoded data is arranged in a 120-column computer output sheet format; descriptive geological information in a 54-column geolog and analytical information in a 64-column assaylog. The acquired data is quantitative, uniform and relatively complete and can be selectively retrieved for processing by a wide range of specialized computer programs developed for the coal mining industry. Visual retrieval of data for manual processing is facilitated by the use of simple codes and logical word abbreviations.

Jan 1, 1977