Search Documents

By H Wen

LongWangGou coalmine auxiliary inclined shaft heading face has a large section, fast heading speed, and large dust production. The problems of high concentration and wide distribution of dust in the roadway air are very prominent. To improve the efficiency of roadway ventilation and dustremoval, long-compression and short-suction (after this referred to as LCSS) are adopted. The dust concentration and airflow field distribution in the roadway are numerically simulated by FLUENT. The change of the position between the pressure duct and the exhaust duct and the different pressure-extraction ratios affect the distribution of airflow velocity, the formation of vortex zone, and the distribution of dust concentration in the roadway. When Ly = 25 m, Lc = 5.0 m, W = 1.2, a wind curtain is formed at 5 m in front of the heading face to prevent dust from spreading deeper into the roadway.

Oct 12, 2022

By Carthew J

For more than 30 years shearer loaders have been the most important winning machines for,longwall mining. While the machines of the first generation had a driving power of only 100 or so kW, the present day shearer loaders may be powered by more than 1000 kW. Daily outputs of 24000 tonnes have now been reached, but this still does not set a limit. If the deposit conditions allow, further increases are possible. This requires the optimum coordination of all system components. For this paper the use of coal plows has been of little import as plows have found no favour, and nor are they likely to do so in today's economics in Australian coal mining.

Jan 1, 1988

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Fidler

Underground coal gasification (UCG) is a process by which coal is converted in situ to a combustible gas that can be used as a fuel or chemical feedstock. The process has been used in commercial-size projects in the former Soviet Union for more than 40 years, while significant national research programs have been undertaken in the United States and Western Europe. The Chinchilla UCG project is located at a site southeast of Chinchilla in Queensland. The UCG operation commenced in December 1999. A controlled shutdown of the process was initiated in January 2002 and successfully completed in April 2003. The process is currently under conservation and ready for restoration of gas production for commercial use in the near future. Groundwater plays an important role in the gas formation process during UCG. Most of the process water required for chemical reactions is usually derived from the coal seam itself and from surrounding aquifers. If insufficient water is available for chemical reactions the UCG gas will contain reduced concentrations of combustible components, and conversely, excessive water influx into the process area would cool down the reactor and thus limit the energy available for gas production reactions. Because of the importance of groundwater in the gasification reactions, and the potential to contaminate groundwater if the process is not correctly controlled, it is essential to predict and to control the groundwater influx into underground gasifiers during and after underground gasification. Control of groundwater requires a thorough understanding of hydrogeological conditions in the vicinity of the gasifier in order to be able to predict inflow rates, and constant monitoring throughout the process of water production rates and groundwater pressure in the coal seam and adjacent aquifers. Hydrogeological testing and groundwater monitoring in the vicinity of the UCG operation commenced six months in advance of its initiation. Monitoring of groundwater pressures in the vicinity of the gasifier have also been undertaken using vibrating wire piezometers installed in the coal seam at varying distances from the gasifier. This paper presents the results of the hydrogeological testing and groundwater quality monitoring carried out at the site, which show that it is possible to operate a UCG process without uncontrolled impacts on groundwater.

Jan 1, 2003

By D Bush, F Goddard

The electrification of Australian mine sites will see a boom in the use of batteries of all chemistries. Lead acid batteries, a traditional mainstay of the mining industry, are expected to nearly double by 2030, however their use will be eclipsed by the explosive growth in lithium batteries. By 2030 the lithium battery market is forecast to be nearly four times the size of the lead acid battery market. Unfortunately, this will result in a corresponding avalanche of waste batteries to be disposed of. Barely a day goes by without battery generated fires being reported in the media and they have become an increasing nightmare for waste management companies and waste facilities. The safe recycling of batteries will also become increasingly important for mine sites to achieve their sustainability goals and reduce their environmental footprint. What are the risks posed by waste batteries, what are the regulatory requirements and how can you manage or eliminate these risks? What current practises does your mine site currently have for the safe management and disposal of batteries from your site? How prepared are you for the coming avalanche of waste batteries?

Apr 16, 2024

By D P. Obeng, L Reemeyer, R Holmes

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

By G Lane

This paper discusses the factors that contribute to the cost effective design of a concentrator. Concentrator design and layout outcomes are functions of the team (engineer’s and owner’s) participating in each particular project. The benchmark for relatively modest projects was set in the 1980s and 1990s during the ‘gold boom’ when numerous cost effective plants were designed and constructed on a lump sum basis in a very competitive market. A number of factors contribute to lack of transference of the lessons learnt in gold plant design to concentrator design including established paradigms in the design and layout of concentrators, lack of experience in cost effective design, operator’s preferences for flowsheet and layout and simple lack of appreciation of the impact of plant footprint on materials quantities and resultant capital costs.Experiences with recent copper concentrator projects (both small and large) are used as case studies.

Aug 8, 2011

By T R. Anderson, A R. Butler

Haymont (2012) notes that in parts of Australia significant areas of mining disturbance cannot be relinquished. In Queensland it has been estimated that by 2010, just 0.3 per cent 507 ha of mining disturbance had been rehabilitated to the regulator’s satisfaction (Short, 2015).One reason for this poor record is the presence of inappropriate, unachievable or unmeasurable rehabilitation targets (Glenn et al, 2014; Butler, Anderson and Sexton, 2015). In the authors’ experience in Queensland many mature operations have licence conditions that hinder the achievement of sustainable outcomes or prevent successful validation of rehabilitation success. This creates a lack of certainty for industry and a lack of confidence in the community that the sector can deliver good rehabilitation outcomes (Short, 2015).This extended abstract presents a framework approach that has been applied at two contrasting operations. Without the changes presented, the goal of progressive rehabilitation certification, reduction in financial assurance (FA) and a path to surrender at these sites would have been impossible. The framework can be adapted for use across different bioregions and commodities.CITATION:Butler, A R and Anderson, T R, 2016. Reassessing rehabilitation objectives and targets for mature mining operations in Queensland, in Proceedings Life-of-Mine 2016 Conference, pp 139–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Mother Nature controls, technical professionals model and miners decide. Decisions to explore, mine and mill. Mine decisions, mine design, planning and scheduling are subject to the quality of models û geological models, geotechnical models, resource models, density models. The closer these models are to reality, the more accurate the predicted outcome. So why is it we delegate the modelling tasks to the most junior and least experienced people? If we insist on this, we need to support them û to provide them with æexperience acceleratorsÆ. Technical mentoring is the most effective way to provide the right information at the right time. When this information (read skills) is supplied at the right time we can inject experience into the quality of our modelling and into our decision- making processes. The objective of this paper is to share those behaviours and manners that foster relationships and create frameworks for skills and experience transfer. Central to this is an understanding of how adults learn, an understanding of the basic rules of mentoring etiquette, and the three keys to building meaningful mentoring relationships. An understanding of adult learning processes and styles provides a structure within which a mentor can understand the learnerÆs perspective. Understanding the world from the learnerÆs point is critical to selecting the right language to engage, teach and transfer skills. Basic rules of mentoring etiquette like timeliness, respect and trust need to be brought into the consciousness so they can be agreed on and monitored to prevent conflicts in cultural and generational norms between the mentor and the learner.Meaningful relationships hinge on the three behaviours: truly listening, rather than just hearing; understanding the technical issues within the WIIFM (whatÆs in it for me?) question; and facilitative behaviour. Stronger and more meaningful technical mentoring relationships within our industry will bridge the generational gap and ensure we can capture and capitalise on the wealth of grey hair experience and develop an informed group of young decision-makers.

Jan 1, 2006

By Lawson F

Narrowly sized samples of synthetic chalcocite (Cu2S) and covellite (CuS) were leached in oxygenated acidic sulphate-chloride solutions. Chalcocite leaches via a two-stage process, the first stage being much more rapid than the second. The apparent activation energies are 42.7 kJ/mol and 68.2 kJ/mol respectively, indicating that both stages are controlled by surface chemical reactions. The leaching of covellite is also chemically rate limited with an apparent activation energy of 77.0 kJ/mol. The shrinking core model is able to be used to describe the leaching processes of both copper sulphides. Over 97% of copper present in chalcocite dissolved in 0.5 M H2SO4i0.5 M NaCl solution under one atmosphere pressure of oxygen at 85¦C in three hours from particles 36 pm in diameter while only 85% of the contained copper in covellite particles 13 pm in diameter dissolved in the same solution under the same pressure at 90¦C in six hours. About 99% of the sulphide sulphur in chalcocite was oxidised to elemental sulphur while only 90% of sulphide sulphur was converted to elemental sulphur during covellite leaching. The mechanism proposed for the two-stage leaching of chalcocite particles is as follows: in the first stage, cuprous ions rapidly diffuse to the external reaction surface where they lose electrons and go into solution as a complex cupric chloride ion CuCl'. The second leaching stage begins when covellite is formed at the external surface. Copper again goes into solution as the CuCl* ion. The mechanism for leaching synthetic covellite is similar to the second leaching stage for chalcocite except that the leaching rate of synthetic covellite is substantially lower than that of the newly formed 'covellite'. Elemental sulphur formed on the particle surface retards the dissolution processes during both chalcocite and covellite leaching. The presence of chloride ions is necessary if essentially all of the copper from chalcocite is to go into solution. When no chloride ions were present, the leaching rate of both newly formed and synthetic covellite was almost zero. The main role of chloride ions in both chalcocite and covellite leaching appears to be to disrupt the passivation film of sulphur on the particle surface.

Jan 1, 1989

The history of the discovery and development of the Kambalda nickel orebody. is reviewed and the decision to process the Kambalda concentrates by the Sherritt-Gordon process at Kwinana is discussed. The Kwinana Nickel Refinery is described and the problems encountered in the first year of operation are Outlined.

Jan 1, 1971

By A N. Parry

In May 2018 Kasbah Resources Limited (“Kasbah”) completed an ore sorting test work program which was a precursor to releasing in July 2018 an updated Definitive Feasibility Study (“DFS”) for the Achmmach Tin Project in Morocco, which it is proposing to develop along with its joint venture partners. The testwork program evaluated ore sorting as a pre-concentration option to achieve early elimination of gangue and the low-grade component of ROM feed, thereby potentially:  Significantly upgrading the head grade of tin to the downstream processing plant.  Significantly reducing the required throughput capacity (and projected capital expenditure) of the downstream processing plant.  Reducing total consumables, power and water requirements in downstream processing.  Increasing the recovery of tin in the gravity and flotation circuit due to the higher feed grade achievable with ore sorting.  Reducing tailings tonnage, tailings cost and environmental footprint.  Using sorter rejects for mine backfill or road base applications. Key aspects of the design of the metallurgical testwork program centred around the need to ensure that samples representative of ROM ore feed (including projected mining dilution) were selected for the ore sorting testwork. The design and implementation of the ore sorting bulk testwork program is described, as well as a summary of the test work results and a discussion of the enhancement of the project economics reported by Kasbah, which led the company to adopt ore sorting as part of the proposed processing circuit in the updated 2018 DFS.

Nov 10, 2020

By T Baumgartl, B Richards

Covers on waste rock and tailings remain the primary choice for closure planning where the purpose is to create an environment where water ingress into reactive material can be controlled and/or prevented. In semi-arid and arid environments, dry cover systems are the preferred option with the design intention to absorb rainfall and to prevent deep drainage. Although the average amount of rain typical for semi-arid environments is relatively low and evaporative demand is high, the seasonal and annual distribution may vary greatly. Rocky substrates are often the only choice for the construction of covers due to economic constraints or availability of suitable materials. While the water holding capacity may be suitable for the application of a dry cover design in arid and semi-arid climates, some of these covers bear the risk of preferential water flow when rain events are intensive or occurring at high frequency. The objective of this presentation is to demonstrate the occurrence of preferential flow through rock containing dry cover systems. A regional classification for the applicability of dry covers is attempted to delineate those regions of Australia where the characteristic of the rainfall pattern increases the risk of failure for dry cover designs. CITATION:Baumgartl, T and Richards, B, 2016. Rainfall patterns rather than climate classification control cover design for closure, in Proceedings Life-of-Mine 2016 Conference, pp 89–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Dyson NF

Nickel sulphide precipitated from waste liquors at the Yabulu plant of Queensland Nickel Pty Ltd was pressure leached under various conditions. Leaching at 130¦C and 700 kPa of air dissolved 95 per cent of the nickel as the sulphate in less than 2 h. Leaching at 130¦C and 350 kPa of oxygen dis- solved 95 per cent of the nickel in less than 1 h. Dissolution was faster with oxygen than with the equivalent pressure of air. Crystallization of hydrated nickel sul- phate from the resulting clarified leachate is readily achieved. Because the sulphide pre- cipitate also contains minor amounts of iron, copper and cobalt, the crystallization product contains these metals in excess of the amounts required for electrolytic-grade nickel sul- phate. This grade of product could only be produced if the contaminants were removed prior to crystallization. Alternatively, the "crude" nickel sulphate could find a market as a feed for the electrolytic production of Ni-Fe coatings.

Jan 1, 1984

By Fukuichi K, Matsukawa H, Nakagawa M

The Myojin Tunnel, located on the Shikoku Expressway being constructed by the Japan Highway Public Corporation, is 3,770 m long with a cross sectional area of 80 m2. Kajima Corporation, the contractor for the northern construction section of this tunnel, adopted here its newly developed "mini-bench" method of excavation. The objectives of this method were 1. to be able to perform all tunnelling operations using the whole cross sectional area of the tunnel under any ground conditions, and 2. to be able to vary the length of the mini-bench within the range of 0 to 7 m according to ground conditions. In order to achieve these objectives, original, sophisticated equipment was developed and employed in the work. One of the newly developed machines is a special jumbo, a hydraulic crawler jumbo with five rotary type booms. This machine is capable of accommodating variation in the length of the mini-bench accompanying changes in ground conditions and is equipped with a special mechanism by which the positions of the booms can be controlled by means of hydraulic cylinders. Also developed was a shotcrete robot for use with the mini-bench method which has the control board near the shotcrete nozzle for close control of application.

Jan 1, 1987

The O.K. deposit occurs within a belt of cherts and spilitised basic volcanics near the western margin of the Hodgkinson Province. The tabular to lenticular shape and gross conformability of the ore bodies; the common occurrence of colloform, framboidal and banded textures in the ores; the lack of significant alteration adjacent to the massive ore horizons and the apparent restriction of stockwork mineralization to the foot-wall side of the massive ore zone at the O.K. mine, all favour a syngenetic origin for the massive sulfide bodies. Furthermore, the micro- structural evidence suggests that the ores have undergone the same deformational history as the country rocks. The invariable association of the ores with spilites; the S isotope values and Co-Ni contents of the pyrites, together with the primitive metal assemblage (Fe, Cu, minor Zn) strongly favour a basic magmatic source for the sulfides. It is suggested-that the sulfides were probably precipitated sub aqueous- ly during a hiatus in volcanic activity. The O.K. deposit is of the cupreous pyrite variety, but unlike other well known occurrences of this type, it does not con- stitute part of an ophiolite complex. While the host volcanics exhibit strong ocean floor tholeiitic affinities, no associated ultra

Jan 1, 1978

The use of teleoperation in mining is increasing due to requirements to improve safety and reduce the number of people required to work in remote and difficult environments. We recently completed a project to develop a teleoperated control system for a rock breaker at an iron ore mine in the Pilbara region of Western Australia, with the objective of demonstrating the feasibility of remote rock breaking over long distances. This required controlling both the rock breaker and an array of pan-tilt-zoom (PTZ) cameras using joysticks. Controlling the cameras distracted operators from the primary task of controlling the rock breaker to position and fire the hammer. This lengthened task times as both the operator's attention and their hands have to swap between different control interfaces. In this paper, we present a novel design using human eye gaze as an interactive input for the remote camera control. It follows a simple and natural design principle: Whatever you look at the screen, it goes to the centre. A prototype system has been implemented by integrating computer vision based eye tracking technology, with the advantage of being real-time, robust and marker-less. We conducted a user evaluation, where users undertook a control task while obscuring the direct view of the working area and using a remote camera to transfer the live video stream as the visual feedback. Subjects were required to participate in the experiment using eye tracking camera control and traditional joystick control respectively. The statistical analysis of objective measures indicated that our novel eye tracking control significantly outperformed the joystick control. The results of the post-experimental subjective measures also revealed much higher user preference for using eye tracking control, which provides clear evidence that this design is a better interface for remote camera control in mining teleoperation settings.

May 1, 2010

By B Ghahreman‐Nejad, M Munro

Design of embankment dams often requires seismic analyses, or an assessment of earthquakeinduced ground and dam movements. There are a large number of cases where earthquakes have triggered sliding and lateral spreading of embankments, resulting in excessive crest settlements. In some instances, liquefaction and embankment failure has occurred resulting in loss of containment. Hence, evaluation of the effects of earthquakes on embankment dams is a critical design aspect. This paper discusses the methods and the results of a seismic liquefaction assessment and deformation analyses of a tailings dam. The tailings dam consists of a perimeter earth core rockfill starter dam which has been raised using upstream construction methods. The embankment raises (formed by an upstream clay blanket and an all-in rockfill body) are constructed over the impounded tailings, which are potentially liquefiable. Extensive field and laboratory tests were undertaken to assess the liquefaction potential of the tailings, and also determine the material properties required for seismic stability and deformation analyses. Numerical modelling of seismic liquefaction and deformation was carried out using FLAC (Itasca 2016) to predict the magnitude and spatial variation of deformations that may lead to an uncontrolled release of tailings. Primarily based on a parametric assessment of UBCSand and Finn-Byrne constitutive models, the results of the analyses are presented and compared for evaluation.

Jul 1, 2021

By Bennet A. G

An overall review of the selection of rock strength and deformation characteris- tics for the design of the Melbourne Under- qround Rail Loop (MIJRL) rock tunnels is presented. Particular emphasis is placed on aspects of in-situ testing, including large diameter plate bearing tests. Material on the interpretation of test results for use in the design of the tunnel linings and openings is included, with a brief discus- sion of desiqn methods.

Jan 1, 1981

By Vestre J, Kure K, Bergqvist I

Existing practical laboratory tests for comparative strength determination of commercial explosives consist of the lead block test, the ballistic mortar test, the bubble test etc. These tests are carried out in material with quite different properties compared to rock. The theoretical performance potentials of commercial explosives are traditionally described by weight-strength (WS). Some explosive producers use the Langefors formula for weight-strength calculation, where also the gas volume is considered. Neither the theoretical nor the practical methods for determination of explosive performance such as the above, give good enough prediction of fragmentation and heave in rock blasting. For these reasons a project was started for the purpose of finding a small scale test method which predicts how different explosive parameters affect fragmentation and heave. Small scale tests were carried out by using 50 cm cubical blocks, mainly of concrete, but a few also of rock. All blocks were blasted in a steel cylinder with a diameter of 1.2 meters. The velocity of detonation was monitored, and the velocity of fragments was derived from their time of arrival at the steel wall, which was registered by accelerometers. After blasting all fragments were screened. The charge diameter was 22 mm and the amount of explosive 78 grammes, resulting in a specific charge of 0.62 kg/m3. Explosive properties such as energy, gas, VOD and density were systematically changed.The results presented in this paper show how fragmentation and heave systematically change when the explosive properties like energy, gas, VOD and density are systematically changed. The results from the small scale tests are compared to full scale tests carried out in tunnel blasting, and during summer 1990 also in bench blasting.

Jan 1, 1990