Search Documents

By Mankosa MJ, Yoon R-H

A reliable scale-up procedure for column flotation must address three important areas of column design, ie column geometry, sparging system and wash water distribution network. The column geometry is dictated by the maximum froth carrying capacity (which determines column diameter) and the bubble-particle attachment rate and particle retention time (which determines column length). The most important factor in the scale-up of an air sparging system is the ability to produce small bubbles in both laboratory and full-scale columns. Other factors, such as energy consumption and maintenance requirements, should also be considered in the scale-up of bubble generators. It is also important to design a wash water distribution system that can properly control the froth stability and maximise the column throughput. Based on these criteria, a successful scale-up example is given.

Jan 1, 1993

By D C. Ford

The Argyle AK1 orebody was discovered in 1979 and subsequently found to be a large, economically viable reserve with high grade diamondiferous ore. Production began via an open pit operation at the end of 1985 and has continued for some 25 years to present day. This, however, will come to an end in the next few years with production moving to an underground operation via block-cave mining methods.A series of studies from 2001 - 2005 was carried out; diamond drilling commenced after approval in 2006, from an exploration drive to determine the likelihood of the current proposed block cave operation.In 2006, development of the block cave project began, in order to realise the part of the orebody below the extent of the open pit mining operation.Development of the block cave technique, comprising an undercut level beneath the target zone of the orebody with subsequent extraction level 15 - 20 m beneath, relies largely on a number of block-caving parameters (hydraulic radius, rock type, structure and orientation of stress and grade of the orebody). These all have an influence on cave ability and eventual profit of the operation. Evaluation of further potential for taking this orebody beyond the block cave phase with options such as sublevel-caving are being considered for the UG-2 portion of the resource/reserve. Diamond drilling for this work is currently under revise.The challenges faced in transitioning form the surface operations to the underground, comprising a changing workforce, converging development drives, underground aquifers, major excavations and transportation of ore via automation are intriguing.

Aug 22, 2011

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By O Jones

Longstanding occupational health challenges of the underground hard-rock mining sector require both an analysis of historical data to assess evidence of linkages between the source of the problem and subsequent illnesses, as well as investigating the means by which health risks to workers can be eliminated or minimised. This paper refers briefly to a recently established National Health and Medical Research Council (NHMRC) sponsored Epidemiological Study into the incidence of Lung Cancer, contracted by mineworkers in Western Australia (WA) due to the inhalation of diesel exhaust fumes from 1996 to 2012. Thereafter it reviews current knowledge of the nature of the challenges facing those responsible for the health and wellbeing of underground hard-rock miners in WA, commencing with the recent categorisation of diesel exhaust as ‘Carcinogenic to Humans, Group 1’, by the World Health Organisation’s (WHO) International Agency for Research on Cancer (IARC). An attempt is also made to explore how the challenge has changed with the adoption of more advanced engine technologies, including the increased generation of ultra-fine volatile organic and other nucleates, submicron carbonaceous agglomerates and toxic gases.The compounding effect of using the mine decline access entry as both the primary ventilation intake and haulage-way is also discussed, as is the need to develop a more appropriate metric for regulating diesel engine emissions. Finally the paper refers to ongoing in-mine research pursued by the National Institute for Occupational Safety and Health (NIOSH) at its Diesel Laboratory in an underground limestone mine near Morgantown in the USA.CITATION:Jones, O, 2015. Diesel exhaust and the underground miner in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Bunting HR

Developments since 1959 in major excavators to meet the high outputs of overburden and coal under the changing nature of the Morwell Coal Deposits of the Latrobe Valley are described. Particular reference is made to investigations of designs of the bucket wheel head configurations for the digging of flat batters on high faces, and examples are given of the wide use ofmodelsin these studies.An explanation is given of considerations leading to selection of the Long Boom or the Compact type of bucket wheel excavator for various applications. The past decade has seen increasing manufacture in Australia of components for excavators and similar machines. The measures undertaken to integrate these components with those from overseas (Germany) are described. A section of the paper deals with advances in Electrical Engineering for large excavators in Australia and its interdependenee with mechanical design and construction. Finally, as an example of the versatility of the bucket wheel excavator a description is given of a recent application for the mining of mineral sands in Northern N.S.W.

Jan 1, 1970

By T Seifert, P Krolop, K Niiranen, S Gilbricht

The Per Geijer iron oxide apatite deposits (IOA) display significant potential mineral resources for Luossavaara-Kiirunavaara AB (publ), known as LKAB. LKAB continuously mines magnetite/hematite ores in northern Sweden for almost 130 years. The Per Geijer deposits reveal a high phosphorus content and vary from magnetite-dominated to hematite-dominated ores, respectively. Furthermore, they show a large variation in texture, mineral composition, and relation to wall rocks. The high phosphorus concentration of these ores results from highly elevated content of apatite as gangue mineral. Reliable, robust, and qualitative characterisation of the mineralisation is required as these ores inherit complex mineralogical and textural features. For this purpose, comminution tests at laboratory scale in combination with scanning electron microscopy-mineral liberation analysis (SEMMLA) were carried out. Based on this work, significant information on the modal mineralogy and degree of liberation of minerals of economic interest (eg magnetite, hematite, and apatite) were obtained. Results show that there is a difference in the degree of liberation of magnetite and hematite between ore types. This seems to be dependent both on the size fractions and the dominance of each iron oxide in the individual ore type. The amount of gangue minerals seems to have no significant impact on the degree of liberation after comminution. Apatite is generally best liberated in ore types associated with silicates, regardless of magnetite or hematite dominance. Based on the results of this study it can be inferred that a high degree of liberation of the minerals of economic interest can be achieved. However, results need to be verified with further beneficiation steps such magnetic separation, apatite flotation and possibly reverse silicate flotation.

Nov 8, 2021

By Porter I, Singh RN

An advanced elasto-plastic finite element model adopting a modified Von Mises yielding criterion was used to simulate progressive failure of the rock strata surrounding a room and pillar mine structure. The model conformed to the strain-softening behaviour of rock and accounted for post-failure residual strength. The simulation was achieved in such a way that material values were updated after each FE run, according to the stress criterion until the solution reached the final equilibrium steady state of the mine structure. The suggested structural stability analysis approach accounted for the main features of the structure degradations produced during loading through changes in rock material stiffness and subsequent evolution of stresses. Comprehensive parametric analysis was performed and the inevitable effect of interaction of the roof, pillar and floor on the overall mine stability limit was investigated. The numerical results clearly showed that linear models could not realistically represent the true behaviour of the mine structure. The results obtained are in good agreement with that predicted in the field.

Jan 1, 1992

By Kubo H, Ninomiya R, Ojiro T, Sato T

New high-strength Zn alloys for moulds are demanded from the automobile and electric industries in Japan, because the s rength of Zn moulds is still not high enough for the mass production. There are two approaches to improve the strength of Zn alloys. One is to increase the Al content. ZA alloys (ZA-8, ZA-12, ZA-27) were developed through this approach. The other is to increase the Cu content. But it is known that an increase in Cu generally depresses the castability of Zn alloys, so that the alloys with increased Cu have been rarely studied until now. In this study a reconciliation between the strengthening and the castability of Zn alloys by enriching both with Al and Cu has been attempted. Accordingly we have studied on the Zn alloys containing 4 to 25 mass per cent Al and to 24 mass per cent Cu have been studied. Their fluidity, which primarily corresponds to the castability of the alloy, were measured first and 19 alloys were selected based upon their fluidities and casting temperatures. Mainly the mechanical properties of all 19 alloys were tested and some were found to be excellent in both strength and castability. Z1009 (Zn-IOAI-9Cu-0.02Mg alloy) cast in a sand mould has the tensile strength of 360 MPa while ZAS (Zn-4AI-3Cu-0.04Mg alloy), which is the most popular alloy for moulds, is 215 MPa. Z2520 (Zn-25AI-20Cu-0.02Mg alloy) cast in a sand mould has a Vickers hardness of 178, compared to 107 for ZAS and 104 for ZA-27 (Zn-27AI-2Cu-0.02Mg). Furthermore the castability of Z1009 is as good as that of ZAS. The underside shrinkage occuring in casting ZA-27 is restrained in Z2520.

Jan 1, 1993

There exist many formulae for designing coal pillars. However, when applied to a given set of mining parameters, they lead to different pillar sizes and factors of safety. From the subsidence point of view, the pillars designed as protection pillars not only have to be stable, but also have to limit subsidence over them to a level acceptable to the structure being protected. The subsidence over a pillar of given width to height ratio depends upon the mining depth. A pillar may be stable, but the subsidence over it may be quite large and unacceptable for the structure. In many cases even though pillars may yield, they support the undermined strata and reduce surface subsidence. In addition, the yielding pillars eliminate peaks and troughs in the surface subsidence profile and reduce ground strains. In a given situation, whether a pillar yields or not depends primarily upon its width in relation to mining depth.

Jan 1, 1992

In taking the chair at this meeting of the Australasian Institute of Mining Engineers, I feel it my duty to thank you for the honour you have conferred upon me by electing me President for the current year, especially as Bwken Hill is the birth place of the Institute and myself one of its foundation members. I will now endeavour to entertain you for a short time with a few reminiscences of Broken Hill from its inception. Beyond the fact that the mines on the Broken Hill lode have paid to their shareholders in dividends and bonuses no less a sum than £896,500, created and maintained a city of 25,000 inhabitants. supplied a large proportion of the revenue on the railways of a sister state, and made their influence felt throughout the 'commercial centres of the world, very little, I regret to say, is known by the general public as to the form, extent, or vastness of the ore bodies, or the mode of occurrence of the various classes of ore which have been found to exist in them. It has occurred to me that a short paper by the senior mining manager on the line of lode might prove interesting. There has been great difficulty in getting some of the figures relating to the field, the total output of metals from the Broken Hill mines not being obtainable from the Mining Department in Sydney j but an inscription on the foundation stone of the Technical College recently opened in this City, sets forth that the Broken Hill Mines started in 1880...

Jan 1, 1903

By Rao S. B, Baafi E. Y

A venturi based multi-scrubber air cleaning system has been developed for dust control along a longwall face in coal mines. The system consists of a number of scrubbers. strategically placed along the wall face which deliver cleaned air at high exhaust velocity into the middle section of the longwall cross-section thus dividing it into two zones. The aim is to maintain the walkway on the powered support side as a zone of relatively clean air. Laboratory studies have shown that the scrubber's average efficiency is 90 per cent. Field trials in three longwall faces have shown that. under normal operating conditions. 40 to 50 per cent average protection efficiency can be achieved within 3 m to 4 m downstream of the scrubber. A three-dimensional finite element computational fluid dynamic model. FIDAP. was used to simulate the airflow patterns the dust concentration and the scrubber dust control technique at a typical longwall face. Results of simulations tally very well with the field results.

Jan 1, 1995

By M Saghaeian, M Zare, V Sheikhzadeh, R Hejazi

High-Pressure Grinding Roll (HPGR) is one of the efficient methods for increasing the specific surface area (SSA) of iron ore concentrate for pellet feed production. HPGR grinding mechanism implies that material should compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study, by doing SSA increasing tests with pilot HPGR, the effects of silica reduction on SSA increasing results were investigated. For this purpose, HPGR tests were performed on an Iranian magnetite concentrate before and after reverse flotation silica reduction tests. Based on the laboratory test results, silicates have been concentrated in two fraction sizes of the sample comprises coarser than 150 microns in form of quartz and finer than 7 microns in form of iron silicates. These silicates have been effected on reduction of concentrate bed pressure resistance by creating a pasty and sticky mud. In this condition, HPGR cannot work properly and operation results are not acceptable. According to flotation silica reduction tests, with 90 per cent weight recovery, concentrate Fe grade is increased from 67.8 per cent to 69.5 per cent and SiO2 content is reduced from 1.98 per cent to 0.9 per cent and especially for lower than 7 microns fraction size, as a critical fraction, SiO2 content decreased from 4.45 per cent to 2.35 per cent. HPGR tests were performed on 8 per cent moisture in 4 N/mm2 specific force and according to the results after silica reduction HPGR operation conditions are optimised. Results showed that the working gap increased from 7 to 10.5 mm and specific throughput of material raised from 180 ts/hm3 to 250 ts/hm3 , and SSA increased by 300 cm2 /gr in a single pass.

Aug 24, 2022

By Hagan T. N

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By L Lorenzen, H Muller

"Every year a large number of projects are evaluated by small listed and unlisted mining companies that are hoping to find the ideal project, which will catapult them from a mining junior status to that of a mid-tier mining company. Usually this includes finding the æidealÆ or ærightÆ orebody and then developing a process which will allow cost-effective recovery of the valuable metals and the production of a saleable product. These dreams are seldom realised and there are a number of good and obvious reasons for this. Issues that are generally high up on the agenda for the smaller companies are: cost of developing a project before the feasibility study stage finding a suitable, or optimum processing technology financing of the project dealing with risk.The most expensive part of the development process for the small miner is often the exploration side of the business and finding the æidealÆ orebody. However, finding the right orebody will not be discussed in this paper. The æidealÆ orebody does not necessarily solve the problems of the mining junior, as much of the uncertainty lies in the process required to recover and produce the final metal product. Once a mineralised deposit has been identified and the grade at least reasonably qualified, the development of a suitable process becomes the driver to convert the deposit into an orebody. This paper proposes that a small exploration company has a very limited opportunity to succeed if it does not do sufficient homework before it identifies the æidealÆ orebody. The risk profile for the small mining company, by its very nature, has to be different to that of a major company and as a result the opportunities often lie in managing different and often new process options, which may be the key to bring such projects on line successfully.CITATION:Muller, H and Lorenzen, L, 2012. Project selection and process development for mining juniors, in Proceedings Project Evaluation 2012, pp 149-158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By Blockley J. G, Laeter J. R

The history of the Ph-Cu-Zn mineralisation in the orthampton Block of Western Australia has been further investigated. It was hoped that (1) Rh-Sr studies on partially-remelled granulites, wall-rocks to the dolerite dykes, should date the dolerite intrusion, (2) Rh-Sr data on hydrothermally-altered dolerite should date the sulphide mineralisation, (3) Pb model ages on the galenas might provide an independent dating of the mineralisation, in addition to any geochemical information that might be derived. Only the second dating aim was fulfilled, but the Pb isotope data, when combined with the Rh-Sr data, have permitted deductions about U, Th and Pb abundance changes during the regional metamorphism, and about a possible source of the ore Pb. In detail the following has been found. (1) The partially-remelted granulitic wall rocks yield a scattered whole-rock Rh-Sr isochron which seems not to have been reset by the dyke intrusion (age 1037 ± 146 Ma, with initial Sr ratio 0.7171 ± 0·0054, MSWD = 111). This date agrees well with that reported previously for granulites from another locality; together theyestablish the time the metamorphic period closed. (2) The hydrothermally-altered dolerites yield a Rh-Sr whole-rock date 434 ± 16 Ma, with initial Sr ratio 0.7072 ± 0·0029 and MSWD = 31, taken as referring to the time of Ph-Zn mineralisation. This contrasts with a report of much older palaeomagnetic and K-Ar datings of the dolerite (not less than 550 Ma, possibly older) and suggests that neither the dolerites nor their heat have had any connection with the mobilisation of the Pbscavenging solutions. (3) The Pb isotope ratios of galenas from the ores yield a well-correlated regression which is not amenable to any of the model-age calculations. (4) The Pb-isotopic trends negate any genetic connection between dolerite and mineralisation, but the country-rock granulites could be the Pb source. (5) Combination of the Rh-Sr dates and the Pb data in a "simultaneous isochrons" construct permits the inference of major losses from the system during the regional metamorphism, in the order U>Pb>Th, with substantial homogenisation of the remaining Pb. This left a wide range in local UlPb and Th/U among the source rocks which eventually were scavenged by the mineralising solutions. (6) These geochemical deductions are shown to be compatible with previously-published information on the abundance ofU and Th in the Northampton Block granulites, which are thus seen to be credible as source rocks for the ore lead.

Jan 1, 1985

By Chitombo G. P, Thompson A. G

Excavation engineering involves three key design processes; excavation design, blast design and reinforcement design. An excavation engineering methodology is proposed in an attempt to promote integration and simultaneous consideration of these three design processes. This methodology requires research and development of, inter alia, a universal rock mass classification system and a universal data display system. Simple examples are used to explain and illustrate the concepts central to these components in the three design processes.

Jan 1, 1995

By Grant JR, McKavanagh BM, Dear SJ

A geophysical technique of rock mass assessment for engineering purposes is being investigated and shows positive correlation with direct structural logging and mapping techniques for the detection of major geological features. The technique is cross-hole acoustic surveying incorporating high speed signal averaging, with a maximum hole separation in excess of 30 metres in hard unfractured rock masses. The bulk of the field test work was carried out in open stopes in the copper ore bodies of Mount Isa Mines Limited. The investigation forms part of an integrated study of blasting in mining, aiming for fragmentation control through blast design modification. The rock quality factor, Q, is presented as a blasting index and can be determined for a significant portion of a production stope.

Jan 1, 1981

By M Davis

Increasing growth in the minerals industry over the past decade has raised the question of whether the standard of training for new geologists has been negatively impacted. This hypothesis was tested by means of a survey. Factors considered included the quality of training and whether it has changed over the past 50 years, preferred styles of training compared to styles of training received and whether the quality of training provided by a company changed with the type or size of company. Data from 435 survey respondents showed a consistent standard of training, but a significant increase in the level of responsibility allocated to new geologists. Those with increased responsibility also had reduced access to additional support and were often asked to perform tasks for which they had little or no training. New geologists were more likely to receive better quality training in a large company (over 100 employees) that owned the mine or exploration lease. A more structured training program was more likely to provide a higher quality result than those with minimal or no structure.

Aug 22, 2011

By Sewell L. G, White H. S

OWING to two large falls of ground which resulted in serious accidents occurring towards the end of 1908, it became evident that the "open chamber" system then in use was unsuitable for the conditions existing in the Mount Morgan mine. It will be admitted that in all mining operations the first consideration is the economy of the system adopted, combined with its safety and ability to give the desired output. A sectional system with square sets has been introduced into the mine, in which due attention has been paid to these factors. In this paper a brief description of this system will be given. An outline of those previously used will be included, as it is necessary to understand the conditions which existed in the mine at the initiation of the sectional system. Outside the actual mining methods employed, various points that might prove of interest will be touched on.The square set system of mining has been in use throughout, the stopes in the gold ore in the upper levels of the mine since underground operations were started in Mount Morgan. In the oxidized zone the ore was of a friable nature, and in some cases rImning ground was encountered. In the lower levels the ground became heavier, and although the stopes were for the most part long, wide, high, and irregular, and not sectionalized, no difficulty was experienced in winning the ore, and no accident of a serious...

Jan 1, 1911

By R Bertuzzi

"This paper presents preliminary results of ongoing research being carried out at the University of New South Wales Australia (UNSW) into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that rock mass strength can be determined following the geological strength-index (GSI) approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions: construction dates from 1880s to 2006 spans from 3.2 to 12.5 m depths from 17 to 124 m excavation methods of drill and blast, roadheader and tunnel boring machine (TBM).Finite element modelling is used to assess the likely magnitudes of the principal stresses that were present at the time of the failures. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zones. Failure and stable points are then compared to the proposed strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown and the spalling criteria. The ability of the Hoek-Brown rock mass strength criterion to differentiate between the ‘failed’ and ‘stable’ zones is considered to be remarkable.CITATION:Bertuzzi, R, 2014. Estimating the rock mass strength of Hawkesbury Sandstone, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014