Search Documents

By R Blin, R Walde, R Belli, D Inaudi

A fiber optic distributed sensing system allows the monitoring of parameters useful to determine the short- and long-term behaviour of the structure in response to the external actions, including, eg seismic activities as well as long-term phenomena such as seepage, tunneling, sinkholes, and other geo-structural movements. Monitoring of large retaining structures with such a system provides direct strain/deformation and temperature measurements on the broad interior area with an arrangement of several sensing cable lines, enabling early detection, localisation and sizing of subsurface damages. Measurements are provided every meter along the entire sensing cable, this is particularly important in such cases where the location of defects and damages cannot be predicted. Fiber optic distributed sensing cables are generally available for retrofit installation inside the dam structure using trenches on the downstream face or laid during construction below the geomembrane liner within the bedding sand layer. Mapping the cable route enables exact correlation between a linear coordinate on the cable length and a position in the dam. Cable installation is envisaged to be carried out during further raising of the embankment; additional cable sections are plugged to the previously installed cables and measured with the existing measurement system, requiring only an update of the mapping. The measurement system is placed remotely from the sensing area since a section of sensing cable can be used to link to the sensing area at the storage facility several kilometers away. The system is available for on-line, 24/7 real-time operational data management. Such fiber optic distributed sensing systems allow storage facilities to be monitored with long, accurate, continuous and precise data for geotechnical diagnostic purposes. This contribution will introduce the principles, benefits, and limitations of this technology.

Jul 1, 2021

As mining and extraction processes improve and lower grade ores become economic, mining for most ores have extended to depths beneath the zone of weathering oxidation created over geological history. These deeper openings expose sulphidic formations and reduced mineral species as either primary ore or simply as accessory or gangue minerals in the country rock. This is not new, underground mining for primary base metal and gold have long been familiar with these problems, as have coal and uranium miners. The change is simply that the number of mines exposing sulphidic waste rocks, tailings to the atmosphere and/or leaving behind dewatered sulphidic rock surrounding the mine void has increased the number of sites from where acid mine drainage (AMD) may emanate with consequential problems for the hydrological environment including downstream catchments (Miller et al, 1996). The principles of ecologically sustainable development (Brundtland, 1987) have been more or less ratified by all the developed nations of the world and this has led, amongst other things, to an expansion unprecedented in the research and documentation of means for achieving long-term environmentally acceptable stabilisation of solid wastes of all sorts. These have revealed that AMD problems can be minimised and even reversed in many cases by the integration or co-disposal of biodegradable organic wastes with oxidising sulphidic wastes (Elliott et al, 1996). This paper considers how this might be achieved at mine sites in Australia and the results encountered at some relevant sites.

Jan 1, 1997

By M Spleit

A long-term production schedule for the LabMag iron ore deposit in northern Quebec, Canada is derived using stochastic integer programming. The optimisation formulation maximises the schedule’s net present value while simultaneously managing the risk of deviations in production tonnages and qualities by considering stochastic simulations of the orebody instead of a single deterministic model. The formulation also smooths and minimises haul truck requirements and ensures that as mining progresses, space is created within the mined out pit for the return of waste material.CITATION:Spleit, M, 2014. Production schedule optimisation – meeting targets by hedging against geological risk while addressing environmental and equipment concerns, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 397–404 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Wong KY, Woodcock JT

Previous results have shown how con- trolled-potential sulphidization (CPS) can give improved metallurgy during rougher flo- tation of mixed oxide-sulphide copper ores. Results in this paper, using different samples and different equipment, confirm the previous results and extend the application of CPS to cleaner flotation. By using CPS, faster flotation of copper minerals (chalcocite and malachite) from clay was obtained in roughing and cleaning, and improved concentrate grades and recoveries were achieved over those by conventional manual control. The optimum sulphidizing potential (i.e. the potential of a sulphide ion-selective electrode versus a saturated calomel electrode) was -500 mV, and could be controlled to ¦5 mV, during four rougher- scavenger and three cleaner-re cleaner stages. This optimum gives the best balance between copper recovery, concentrate grade, and sodium sulphide consumption. Five cleaning circuits and five ore com- posites of different composition (0.55-1.50 per cent Cu) were examined as well as the effect of feed size and pulp density. Better results were obtained at 20 per cent solids in a Denver cell than at 33 per cent solids in an Agitair cell; this may have been related to the high clay content of the ore. Commercial equipment for pilot plant or full-scale plant application of CPS is cur- rently being developed.

Jan 1, 1986

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

By J Loeb, J Dampney, P Cameron

Optimisation of Blast Design and Execution must be done right the first time. It is too late after the ore is broken. Consequences of poor design and execution negatively affect productivity from load and haul through the primary crusher to processing and hence reduce mine site profits. Harnessing and utilising ‘big data’ from geology, geometallurgy, drill hole location, powder loading, blast timing, blast movement and fragmentation to close the loop in blast design and optimise the blast increases productivity across the entire value chain from Mine to Mill. As the internet of things and artificial intelligence increases the quantity of data available, being able to capture and utilise this data to advantage is a challenge. Recent advances in software and hardware together with the increased power of cloud computing allows engineers to close the blasting loop to increase mine site productivity. Numerous case studies over the years detail significant gains from implementing the innovative technologies available to Mine to Mill projects. The opportunity is available for all members of the multi-discipline teams at each mine site to actively ensure productivity improvements are realised and maintained not only in their area, or silo of responsibility but across the entire mine site. This paper refers to recent case studies which outline how significant improvements in productivity are available to all mining operations to increase mine site profitability and dividends to shareholders.

Jun 22, 2022

The tankhouse of the electrolytic zinc plant at Nordenham is operating with a very high operating efficiency of 99 per cent. This has been achieved not only by strict control of the quality of the zinc sulphate cell feed solution but also by all the improvements in housekeeping in the tankhouse developed during the past years: aluminium cathode specification, cathode stripping cycle, edge strips, copper contacts, anode isolators, cell cleaning, fittings and washing devices. During 1987 to 1992 the casting department was completely remodelled in order to improve the quality of the zinc products, the safety of the operations and the flexibility. The remodelling includes the enlargement of the area for the casting shop, the storage buildings and the five casting lines on the same ground level. New lines for alloying products and for SHG25 kg zinc ingots have been constructed. The line for galvanising products has new equipment in some parts and the other lines have been modified.

Jan 1, 1993

By M A. Rhamdhani, K Avarmaa, A Putera, J Chen, G Brooks

Silicon-based photovoltaic cells are currently the most dominant types applied to convert solar energy to electricity. In solar-grade silicon (SG-Si), the control of boron (B) and phosphorus (P) is very critical. Generally, these elements are difficult to remove into acceptable sub-ppm levels from lower grade Si. This study investigates slag treatment as a process for Si refining, focusing on the behaviour of P and B. The experiments were conducted by equilibrating Si-B-P alloys with 43 wt per cent SiO2 – 47 wt per cent CaO – 10 wt per cent Al2O3 slag under inert atmosphere at 1500°C. Different crucible materials were used (Al2O3, SiO2 and MgO), which determined the primary saturation phase for the system and modified the final slag composition accordingly. The samples were equilibrated and analysed with microanalysis techniques (EPMA (electron probe microanalysis) and LA-ICP-MS (laser ablation inductively coupled plasma mass spectrometry)). New standards were prepared and applied in the LA-ICP-MS analyses. Experimental results show that silver is essentially fully dissolved in silicon, as well as most phosphorus with LP ( = wt per cent P in slag/wt per cent P in Si) between 0.1–0.3. The distribution coefficient of boron was measured to be between 1 and 2. The crucible material used had an influence on the phase compositions and slight influence on the distribution coefficients of boron and phosphorus. The experimental results provided new accurate data when considering applicability of slag treatment as a technique for Si refining and Si PV cell recycling.

Jun 19, 2024

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022

By B Armstrong

The Proterozoic poly-metallic Trilogy deposit was discovered in 1997, and until recently, mining evaluation was stalled due to poor metallurgical performance. Unlocking the substantial economic value of the deposit required a coming together of geologists, mineralogists, metallurgists and mining engineers, who by working collaboratively, uncovered the detail necessary to allow the required metallurgical breakthroughs to occur. The deposit itself is described as a sedimentary exhalative (SEDEX), with an enriched lead-zinc-silver core surrounded by a broader envelope of copper-gold mineralisation. The geological domains were defined in broad terms based on the style of mineralisation, assay values and lithology. These domains, while adequate for the resource estimation process, failed to translate into representative metallurgical domains. Additional work with new techniques defined regions in the deposit with altered processing properties which could not be recognised by conventional geological logging. Such additional complexities could not be appreciated at the outset of the metallurgical test work program.These regions were defined by applying the EDTA analysis method for recognition of where the valuable sulfides, particularly galena, had been partially modified by oxidising conditions. Hence, the flotation response of the valuable sulfide minerals was diminished and the increased amount of heavy metal cations available in the system significantly reduced selectivity in the flotation process.Understanding the detail of this complexity was essential in determining representative metallurgical domains, which was the first step in the long road of development.

Sep 5, 2011

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Sullivan

The key skills for a competent geologist are observation, documentation, analytical thought and the ability to communicate. These attributes have served the geological world for the past two centuries since the field of geology was separated out from natural philosophy. The understanding of the structural setting, lithologies, alteration and 3D distribution of the target mineral species are essential precursors to resource evaluation and potential economic extraction. The advent of artificial intelligence and machine learning has matured to the point where observation by dedicated sensors and analysis by customised AI algorithms can replace manual processes and deliver credible results. In combination with analytical data such as assays, various sensors now collect physical properties of rocks which are used as proxies for mineral identification and rock mass classification. These sensors include X-ray and infra-red spectra, magnetic susceptibility, gravity/density, EH/pH measurements, conductivity, colourimetric readings, porosity, fracturing and fracture intensity. Analysis using machine learning techniques trained using known data sets can determine rock type classification, rock density, quantification of grade/quality attributes, mineral alteration, weathering and geotechnical attributes such as rock quality. This type of data relies on calibration and quality control of a variety of different types of electronic hardware. The resulting data is non-additive, has error ranges and will be suitable for consumption by fast AI methods providing probabilistic analysis. A second stage could include geometallurgical constraints to provide an ‘extractability index’, which is of more interest to miners than pure geotyping. Using resultant interpreted geological criteria, 3D domain models with spatial attributes will be built.

Sep 1, 2024

By N L. Turner, K Ehrig, V Liebezeit, D J. Robinson, L L. Kuhar, N Francis

Conventional industry tests used to determine leach recoveries are often fully monitored and may be time-consuming and expensive. Such tests may be limiting in geometallurgical applications where large numbers of samples are required to be processed for characterisation of an ore deposit. BHP Billiton currently use a fully instrumented leach test for characterisation of Olympic Dam uranium-rich samples. Researchers at the Commonwealth Scientific Research and Industrial Organisation (CSIRO) were approached to develop an alternative to these full-scale leach tests that could allow for the ranking of samples in terms of their leachability. The novel geometallurgical test was required to use samples of small mass and be affordable and rapid.Three leach test protocols were pursued in developing the small-scale tests. Kinetic leach tests were performed using mild conditions at higher pH, low temperature and low oxidation reduction potential, moderate conditions at intermediate pH, temperature and oxidation reduction potential and aggressive conditions at lower pH, higher temperature and higher reduction potential.This paper presents results from 44 leach tests on 11 samples with varying uranium mineralogy. The developed small-scale tests correlate well with data from the more costly conventional industry laboratory tests, indicating the possibility of using this alternative test as a geometallurgical leach proxy. Simple regression analysis confirmed the importance of pH, reduction potential and temperature on uranium extraction. Experimental data were fitted to published leach models to predict uranium leach extraction for a range of operating conditions.The ultimate aim of the test work is to combine a limited number of large-scale calibration tests, a large number of small-scale geometallurgical tests and leach models for geometallurgical sample characterisation and evaluation of a wide range of scenarios or processing options.CITATION:Turner, N L, Kuhar, L L, Francis, N, Liebezeit, V, Ehrig, K and Robinson, D J, 2013. Development and testing of a small-scale uranium leach for geometallurgical applications, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 345-350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J V. Lawless

Two types of low sulphidation epithermal deposits that have different gangue mineralogies and ore shoot geometries are recognised. One has laterally near-continuous ore shoots over a significant vertical interval that consist of quartz, chalcedony, pyrite, minor base metal sulphides and adularia, with electrum. The other type of deposit has discrete near-vertical ore shoots of a lesser vertical extent, that consist of quartz, pyrite, base metal sulphides, sulphosalts, electrum and in their upper parts barite, which are enclosed in veins of earlier quartz. The gold mineralisation in both deposit types is considered to be a co-precipitate of pyrite, with that in the first type of deposit produced by prolonged boiling in an upflow of a hydrothermal system (Upflow Deposits); an example is Waihi in New Zealand. The other type is produced by mixing, a deep water primed for gold deposition by prior limited boiling, with an iron-bearing oxidised condensate of the steam released by the boiling, in an outflow of a hydrothermal system (Outflow Deposits); an example is Thames in New Zealand. Early recognition of these different types of deposits can be used to develop mineralisation models of predictive value on which to focus exploration drilling. Early recognition of an Upflow Deposit promotes an extensive program to delineate the extension of the main ore shoot. In contrast recognition of an Outflow Deposit requires a more intensive approach to find individual ore shoots which, although smaller than those found in Upflow Deposits, may be high-grade, particularly if there is earlier mineralisation present to act as a protore.

Jan 1, 1999

By D Johansson, C Yi

Blasting techniques are widely used to fragment rock masses into smaller pieces. Numerical modelling is an efficient method employed by many researchers in the blasting field. It is difficult for a conventional continuum-based approach such as the finite element method (FEM) to model the rock fragmentation by blasting and the expansion work on the rock by explosive and its detonation products. In this paper, the particle blast method (PBM) was employed to model the behaviour of the detonation and a bonded particle model (BPM) was used to model the brittle material to be blasted. A mortar cylinder with a centrally placed hole for the explosive was modelled and the results were compared to the experimental data. The blast process from crack initiation to fragment formation was analysed. The influence of coupling ratio on fragmentation was also investigated.CITATION:Yi, C and Johansson, D, 2015. Discrete element modelling of blast fragmentation of a mortar cylinder, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 793–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

By Adusumilli M. S, Subrahmanyam T. V, Rao V. D

Chance find of an economically important mineral on the sur- face and its exploitation without proper exploration work, has become the habit of humanity since the Bronze Age. The explora- tion and exploitation techniques have, however, been substan- tially improved in the technologically developed western world and system controlled major communist countries. Nevertheless, the greatest need is felt in the Third World countries where large mineral potential exists, but with inadequate investments in exploration and exploitation techniques, a handicap that has been beneficial to the more developed countries, since long. The great number of the Third World countries which are striv- ing hard to develop, need to formulate mineral exploration and exploitation strategies which could enable them to develop their resources. This requires planning and creating new concepts of ore deposit types and genetic models, rheology, economics and their innovation and integration. The following approach could help them to be economically "more independent" by the end of this century. 1. Bridging of pure and applied geology gap, and creating con- sciousness of research and development. 2. Revision of mineral resources concepts adopted to modern technological world. 3. Improved mineralogical research, and determinative miner- alogy as an important asset. 4. Creative research and establishing know-how, with philosophical base for regional exploration projects. 5. Indepth investigation into the origin and growth of earth as a system, and its importance in the association, quality, and quantity of metallic, non-metallic and energy resources con- centrations. 6. Mineral beneficiation, targets and strateties; methods of eco- nomic and improved recovery systems. Development of alter- native technology, and utilization of mineral technology strategies. 7. Theoretical and practical modelling by conventional and com- puter techniques of the existing and expected mineral resources, and mineral development. 8. Critical analysis of the status of mineral economics of the Third World and developed world with forecasts for the year 2000 based on problems faced by the developing world. 9. Minerals at cross roads of International Interdependence. 10. Philosophical, realistic, traditional and modern strategies for mineral development. The dynamic economic system opera- tion in national mineral sector.

Jan 1, 1988

By Maloszewski J, Kidybinski A, Sawka B

A forecast of mining conditions in Upper Silesia collieries for the beginning of the 21st century has special focus on average depth of mining, energy of seismic tremors induced by mining and energy of dynamic loads on roadway supports. A method of dynamic loads calculation is based on volume of failed rock surrounding an opening and the seismic energy of tremors anticipated. New types of yielding steel arch supports have been designed to resist massive static and dynamic loads and a system of supports has been tested both on 1 : 10 scale models and in natural size. The support sections used are 29, 36 and 44 kg/m.

Jan 1, 1988

By Bidwell TJ, Servant S

Paste back-fill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste hackfll is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the hackfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in-situ measurement of paste backfill properties.

Jan 1, 1998