Search Documents

By P. Gobin, J. Perez, P. Peguin

The strain-amplitude- dependent part of the internal friction of alluminum after several ther momechanical treatments has been measured in the I-cycle range and at the ambient temperature. The internal friction in the outer layer of the torsional specimen us stress is computed from the experimental data. The curues obtained are analyzed in tevnzs of u coirzbinntion of AH and p, which aye, respectively, due to the vecersible unpinning from weak pills and to the plastic strain. Considerirlg the notion of thermally activated unpinning and repinning, it is shown that in our experimental conditions tlze dislocation lines acl as in the H model of Granato and Liiclze. It is also seen that the internal friction p which appears at higher- strains call be described by a simple expression which is in good agreement with our results. A qualitative interpretatiorz is proposed by combining these new types of intelpnal fviction. We define the internal friction 6 as half the ratio of the dissipated energy aW during one cycle to the maximum supplied strain energy W of a material submitted to a periodic stress. Experiment and theory show that internal friction varies with stress above a critical value.' Below this value the internal friction is strain-amplitude-independent and is often masked by an experimental background; so we shall call it AB. ~bove this critical value, the internal friction is strain-amplitude-dependent. This quantity is usually called aH:' and it can be explained as a thermal unpinning of dislocations.3-6 Furthermore, at higher stresses, a rapid increase of internal friction appears. This phenomenon could be caused by the plastic strain,' so we shall call it Ap. It seems interesting to us to study the influence of several t her momechanical treatments on the curve internal friction 6 vs strain E, in order to study the variation of AH and p with the concentration and the repartition of linear and point defects. In order to try to explain the results obtained, we shall propose and discuss models for H and hp and shall show that we obtain a combination of these two types of internal friction. 1) EXPERIMENTAL PROCEDURE 1) Preparation and Treatment of Specimens. We

Jan 1, 1968

By S. S. Raymond, C. R. Hayward

In reheating quenched steel to remove part of the hardness, the softening effect has generally been considered to be a function of temperature and time. The temperature effect is well known, and long before pyrometers were heard of the blacksmith was able to do a good job of tempering, by rule-of-thumb methods and experience in judging temperatures. Modern conditions, which demand steel that will withstand the severest tests, require that the heat treatment be carried out with every possible precaution to secure the best results obtainable. Pyrometers and heat-treatment furnaces of many types are on the market and improvements are continually being made so that it is now possible to regulate the temperature in heat treatment very accurately. There is still a question regarding the time that the steel should be subjected to treatment. It is customary with all operators to insure the desired temperature throughout the specimen and it is generally supposed that a longer treatment of a hardened steel produces a further softening but there are few published figures showing the exact effect of time of treatment at constant temperature. A search of the literature disclosed several brief statements that the tempering effect was a function of both time and temperature, but in no case were any figures given. The opinion is very generally held that the well-know tempering colors are accurate indicators of the degree of tempering. This is disputed by Brearley (The Heat Treatment of Tool Steel, page 102) who states: It has been said that the result would be the same in respect to both hardness and other properties whether the colors were obtained by a shorter heating at a higher temperature or a longer heating at a lower one. This, to say the least, is a very doubtful conclusion, and is certainly not borne out by mechanical tests on oil-hardened and tempered motor car steels which, after tempering for periods varying from 15 min. to 2 hr., show no very great bifferences. The present investigation had for its object the obtaining of some definite data regarding the effect of time, which might serve as a guide to those engaged in the heat treatment of steel. The Rhode Island Tool Co. cooperated by furnishing the steel and machining the test specimens.

Jan 1, 1917

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By M. C. Udy, F. W. Boulger

AN incomplete phase diagram for the U-Ti systern was determined earlier 1 and more recently, a tentative diagram was presented for the uranium-rich end of the system.' In the present re-examination of the whole system of U-Ti alloys, high purity materials were used. Melting stock for the alloys was high purity uranium, containing about 0.09 pct C as the only appreciable impurity, and high purity iodide-process titanium purchased from New Jersey Zinc Co. Both metals were cold rolled to about 1/6 in. thickness, sheared to about I/' in. squares, and cleaned by pickling. The alloys were arc melted under a helium atmosphere in a water-cooled copper crucible. A thoriated-tungsten electrode was used. The furnace chamber was evacuated, then flushed with helium, prior to each melting. It was finally filled with stagnant helium at one atmosphere pressure. Each alloy was remelted three times after the original melting, to insure homogeneity. The alloy button was turned bottom side up before each re-melting operation. Some 22 alloys were examined. Their compositions were spaced at appropriate intervals between 100 pct Ti and 100 pct U. Analyses were made on chips taken after fabrication. The major contaminant was carbon, which varied from 0.03 to 0.08 pct. It appeared in the microstructure as titanium carbide. Alloy compositions were calculated to a carbon-free basis for consideration on the diagram. Tungsten and copper, possible contaminants from the melting operation, were generally less than 100 parts per million each. Fabrication All alloys were forged and rolled to bars approximately V8 in. square. They were clad either in SAE 1020 steel or in a 5 pct Cr-3 pct Al-Ti-base alloy, depending on the fabrication temperature. A temperature of 1800°F (980°C) was used for alloys near the compound composition. This necessitated using the titanium-base alloy, since iron reacts with titanium at this temperature, producing a low melting alloy. Other alloys were fabricated at 1450°F (790°C), using steel jackets. No iron-titanium reaction occurred at this temperature. The jackets were welded in place in an argon atmosphere. Those alloys sheathed in steel were declad and then reclad between rolling and forging operations. On the other hand, those clad with the titanium alloy were cut to a roughly rectangular shape prior to clading and were then carried through both the forging and rolling operations without opening. Those alloys near the compound composition were found to be cracked when the clading was removed. The cracked materials had been plastically deformed, however, and at least some of the cracking had OCcurred during cooling. Heat Treatment The rolled bars, after being declad and shaped to remove surface contamination, were all given an homogenizing treatment of 160 hr at 2000°F. (Samples were taken for analysis following the declading and shaping operations.) All were heat treated at the same time in one furnace, but each was sealed in a purified argon atmosphere in an individual Vycor glass tube. Argon pressure was such that it was approximately atmospheric at temperature. One end of each tube contained titanium chips and this end was heated to 1200°F (650°C) for 10 min prior to the heat treatment. This purged the atmosphere of residual reactive gases. The balance of the tube was warmed during the purge to liberate adsorbed moisture and gases, which also reacted with the hot chips. The bars were furnace cooled from the homogenization treatment. Specimens of each alloy were water quenched after 2 hr heating at 1000°, 1200°, 1400°, 1600°, 1800°, and 2000°F (540°, 650°, 760°, 870°, 980°, and 1095°C). In addition, some were treated at intermediate temperatures of 1300°, 1500°, and 1700°F (705", 815", and 925°C) and at 2150°F (1175°C). Specimens, about '/s in. cubes, were cut from the bars, sealed in individual Vycor tubes, and heat treated as described. All specimens heat treated at the same temperature were processed together. Samples were quenched by breaking the Vycor tube rapidly under water. Metallographic Examination Specimens were mounted in bakelite and ground wet on 180 grit paper held on a 1750 rpm disk. They were then ground wet by hand, using 240, 400, and 600 grit papers. The rough grinding was continued long enough to get well below the surface. Specimens were mounted separately because of the variation in the rate of etching between alloys. The specimens were polished with rouge on a 4 in., 1725 rpm wheel covered with Miracloth. Alloys on the titanium side of the compound composition were etched with a solution of 2 pct hydrofluoric acid in water saturated with oxalic acid. A few crystals of ferric nitrate were added as a bright -ener. Specimens were immersed 5 sec, polished to remove the etch, then re-etched. With the higher titanium alloys, it was often necessary to start the etch on the polishing wheel, because of the formation of a passive film. In some instances, a plain 2 pct hydrofluoric etch was satisfactory. For the alloys on the uranium side of the compound, a distinction between the compound and the uranium phase developed after standing a short time in air. This could be hastened by the application of heat, such as obtained by placing the specimen on a radiator. A deep etch was necessary to develop details in the uranium-rich phase, such as the Widmanstaetten pattern sometimes obtained by quenching y uranium. A 2 pct hydrofluoric acid solution was used for this deep etching.

Jan 1, 1955

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first. MISFIRES CAUSED BY FAULTY DETONATORS The important part of an electric blasting cap, to the user where multiple shot-firing is done, ass in the steep-pitch, thick-vein, anthracite mines, is the bridge wire. In single shot-firing this factor is not apparent, but in mines where multiple firing is done any variation in the resistance of the bridge wire, where full or even rated battery capacity is required, will most likely cause a misfire The reason for this is obvious. If the resistance in the bridge wires is not the same, some of the detonators will fire because of their greater comparative resistance. Variance in resistance of bridge wires is caused by a slight difference in the diameter of the bridge wire, also to a difference in the composition of the bridge wires. Again, where the bridge wires have become rusted, there will be a variance in resistance. About the year 1922, one of the large coal companies was greatly alarmed by the number of serious and fatal accidents caused by misfires. The general manager issued an order that these accidents must be greatly reduced, and if possible, entirely prevented.

Jan 1, 1929

By C. L. Ray, R. E. Baarson, H. B. Treweek

As an example of nonmetallic mineral flotation, the separation of several pegmatite minerals will be discussed in considerable detail, from both the laboratory-testing and plant-operation standpoints. The pegmatites have been chosen to illustrate the practicality of the selective separations of the minerals in a complex nonmetallic ore and, in so doing, to set forth a summation of the flotation art and technology which is applicable in part to the beneficiation of several less complex nonmetallic ores. In addition, a brief summary of descriptions of other nonnietallic mineral flowsheets and separations is included. Some of the industrial minerals now being concentrated by froth flotation methods commercially, or in the laboratory, are listed in Table 1. GENERAL CONSIDERATIONS There are two classes of chemicals that are normally utilized as collectors in froth flotation separations of nonmetallic minerals. These are defined as anionic and cationic and are typified by the fatty acids and amines, respectively. The fatty acids are selective to those minerals that have a high concentration of positive surface charges, such as the various calcium minerals typified by calcite, phosphate rock, and fluorspar. The amines are selective to those minerals with a high concentration of negative surface charges, such as silica sand and silicates. It should be noted, however, that by using various inorganic chemicals, a new or synthetic surface can be placed on specific minerals which produces different characteristics, thereby reversing the flotation reagent required for separation. The polar end of the collector attaches to the mineral surface either by chemical or physical adsorption; the nonpolar unreactive end is oriented away from the mineral surface. The result is a hydrophobic coating at the mineral surface which causes attachment to air bubbles. It is this surface condition that permits the floating of minerals which normally sink in water. In order to utilize these fatty acids and amine derivatives, several conditions .must be fulfilled. Before there can be a selective flotation process,

Jan 1, 1962

F. AT. FARMER*, New York (written discussion?)- The paper presents many phases of the welding art concerning which there are very divergent views. In many cases, the wide differences of opinion are based on the results of mechanical tests, but an examination of the mechanical test data discloses a wide variation in character of the tests made and in the details of procedure, so that it is frequently not only difficult to analyze and check the basis of the conclusions but impossible to correlate various groups of test results. It would seem, therefore, that the technique of testing welds is one of the phases of the welding art that should be studied and standardized in order that the results of mechanical tests made by different people may be strictly comparable and have the same significance to all. The vital difference between testing a specimen of steel that includes a welded joint and testing an ordinary specimen is the non-homogeneity of the weld specimen. The weld specimen has at its center a section composed of material that usually has physical, chemical, and metallurgical characteristics distinctly different from the adjoining metal. Furthermore, the section of added metal is more or less irregular and the ratio of added metal to original metal in the section is quite variable. Consequently the details of procedure and of recording data should be more minutely prescribed than in the testing of ordinary specimens. A conspicuous example f a mechanical test that requires standardization is the cold bending test, a standard test for mild steel. With the usual method, the specimen is bent around. a pin of prescribed diameter and, as all specifications usually require bending to 180° without fracture, the manner of applying the load is immaterial because the specimen is ultimately completely wrapped around the pin. But a specimen containing a welded joint at the center will usually not withstand bending to 180° because of the much lower ductility of the deposited metal in the weld. It is therefore obvious that the farther apart the points of support are the greater will be the angle attained before cracking occurs, simply because most of the bending will take place in the original metal. It is therefore highly desirable that there be prescribed a standard test that fixes exactly the distance between the supports, the curvature of the surface of supports, and the relation between this curvature, that of the loading surface, and the thickness of the specimen.

Jan 5, 1919

By N. E. Truitt, D. G. Russell

The transient pressure behavior of a well which produces a single compressible fluid through a singte-plane wrticat fracture has been investigated mathematically. The fracture is assumed to possess infinite flow capacity, to be of limited mdial extent, and' to penetrate the producing formation completely in the vertical direction. Previous studies of vertically fractured wells have been concerned primarily with production rate performance or semisteady-state pressure behavior. This study was undertaken to ascertain the influence of vertical fractures on transient pressure tests such as pressure build-ups and flow tests. In a vertically fractured system, flow in the region nearest the fracture is practically linear, whereas farther away from the fracture essentially radial flow prevails. Thus, transient pressure analyses based on radial flow theory are somewhat inaccurate. As fracture penetration increases radially, kh values calcutated from pressure build-up and flow test curves become increasingly larger than true values. Failure to consider the effect of fracture penetration also introduces inaccuracies into the catculation of fracture length from the apparent skin factor and into the determination of average reservoir pressure. If the total length of the fracture is 20 per cent, or greater, of the drainage radius of the well, corrections must be made to pressure build-up and flow test results. Methods for correcting such results are discussed in this paper. For wells with prefracturing pressure build-up or flow test data, it is possible to estimate fracture length by comparison with postfracturing build-up or flow test results. In new wells or wells without prefracturing build-up or flow test data, fracture length must be estimated to correct the values obtained from analysis of pressure tests after fracturing. Fracturing efficiency calculations should be made whenever possible to provide an estimate of fracture length. Tables of the dimensionless pressure drop as a function of time and fracture penetration are included in this paper. Using these values should permit analysis of other types of transient pressure behavior in vertically fractured wells. INTRODUCTION Hydraulic fracturing has been used quite successfully for over a decade as a completion and stimulation technique in oil and gas wells completed in low-permeability reservoirs During this period a considerable amount of theory has evolved on the performance of hydraulically fractured reservoirs and on more efficient means of artificial fracturing. Although theory has been developed, no rigorous investigation has been made of pressure build-up and flow test behavior in such wells. Prats et al.1 first discussed the performance of vertically fractured reservoirs for the case of a compressible fluid. Their work was primarily concerned with production performance at constant flowing pressure. These authors also considered large-time (semisteady-state) constant production rate behavior for vertically fractured wells; however, transient pressure behavior at constant rate was not investigated. McGuire and Sikora10 and Dyes, Kemp, and Caudle2 employed an electrical analog to investigate the influence of artificial vertical fractures on well productivity and pressure build-up. They found that fractures which extend beyond 15 per cent of the drainage radius away from the well alter the position and slope of the straight-line portion of the build-up curve. They concluded that these effects must be considered both in the determination of the effective permeability of the formation and in any calculations of final build-up pressure. Although these authors did not undertake an exhaustive study of the influence of vertical fractures on pressure build-up performance, their limited results were quite interesting from the standpoint of the effects they demonstrated. In a more recent paper, Scott- reported the results of an investigation of the effect of vertical fractures on pressure behavior, which was conducted with a heat flow model. Scott's results appear to be consistent with those reported in Refs. 1 and 2. However, the effects of different fracture lengths on performance were not investigated. Pressure build-ups and transient flow tests are among the most diagnostic tools available to the reservoir engineer or production engineer. Since a very high percentage of present-day well completions incorporate the hydraulic fracturing technique, a definite need exists for information on the effect of fractures on transient pressure performance. For these reasons we have undertaken a rigorous study of pressure build-up and flow test behavior in vertically fractured reservoirs. The objectives of this study were (1) to obtain synthetic pressure build-up and flow test

Jan 1, 1965

By F. J. Radd, R. L. McGlasson

The mechanisms of corrosion and corrosion fatigue damages to sucker rods are examined from a fundamental electrochemical viewpoint, and the relationships of sucker rod microstructures to these damaging effects are defined. The common corrosive agents in crude oil production and storage are discussed as to types of attacks that they cause. The variations of fatigue strength with alloy content, surface preparation, and stress ranges are analyzed. Finally, conclusions are drawn as to how microstructures largely influence and control sucker rod performance. INTRODUCTION Greater than 90 per cent of the crude oil produced by artificial lift methods is produced through sucker rod pumping systems. In the USA each year more than $14 million is spent for sucker rods in new and old pumping installations. It is important to make this investment a wise one. Essentially, the sucker rod system is a long series of steel rods, operating under alternating stress loadings and under mechanical vibrations, which connect the surface power source with the subsurface pump. These rods often operate in a variety of corrosive media, including water, brines, carbon dioxide, hydrogen sul-fide, and air. Basically, this paper is concerned with the problem of the behavior of certain steels in various corrosive media under high and dynamic stress patterns. The main objective of this paper is to show how, once the stress effects and the corrosive environments are defined, one can still realize structural control and beneficial influence upon corrosion and corrosion fatigue. FUNDAMENTAL DEFINITIONS AND ANALYSIS In the corrosion and stress behavior of this solid state mixture of iron and iron carbide called steel, one must analyze upon what major factors does its service life depend and of what, exactly, is steel composed. The former question can be referred to two external factors and two internal factors. The two major external factors are: 1. the nature of the stress patterns — size and range of stresses present 2. the nature of the corrosion — erosion environment — the corrodent and/or wear involved The two fundamental internal factors that govern the strength and useful life of a steel both in normal duty and in heavy-duty corrosion service are: 1. the nature of the steel volume properties 2. the nature of the steel surface properties For the latter question normal steel is defined as a solid mixture of iron and iron carbide particles, generally with certain accidental and intentional elements present. (The amount of iron carbide present is determined by the carbon content of the steel.) These additional elements generally dissolve into either the iron (ferrite) or the iron carbide (cementite) components.

Jan 1, 1955

By Robert P. Burrows

In preparing this paper the object has been to set forth facts relating to illumination problems, which, judging from the results realized in the iron and steel and other industries somewhat similar to mining, will tend toward furthering safety, production, and contentment of employees, as well as economy of operation in mines. By applying the principles of illumination with the assistance of modern appliances, the full benefits in efficiency may be derived from improvements already made in other details of mine operation. The lighting of a typical coal mine may be*divided into four distinct parts: 1, The lighting of the buildings about the top; 2, the lighting of the working faces; 3, general illumination at the bottom; and 4, special applications of lighting. The lighting of buildings about the top may be treated in the same manner as that of any other industrial plant, for we have a boiler room, an engine and generator room, a forge, a machine shop, and a hoist room. These can be well and efficiently lighted by the use of 100-watt tungsten-filament multiple lamps with proper reflectors so spaced and suspended that a power consumption of from ¼ watt per square foot in the boiler room to 1 watt per square foot in the machine shop is obtained. The methods that apply to this kind of lighting have been ably treated by a number of authors,' and for this reason a detailed discussion is unnecessary. The lighting of the working faces is usually done by means of portable lamps, of which there are four types in use: The oil torch, the acetylene Iamp, and the oil and the electric safety lamps. The different types have been fully described in numerous papers and articles and will not be covered here, although a few figures on the cost of operation will no doubt be

Jan 1, 1916

By M. N. Dunlap

Tries article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. All were abandoned because of liability that would be incurred by flashflood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it would normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 95 ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 2 1/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief : 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 5 1/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1947

By F. C. Sturges

[CONTENTS PAGE ................. Introduction-Grouting in Mines. By F. C. STURGES. I Use and Technique of Pressure Grouting in the Construction Industry. By V. L. MINEAR . 3 Technique of Pressure Cementing in the Petroleum, Mining, and Construction Industries. By WY. D. OWSLEY and R. E. MOELLER. ..................... 9 An Example of Controlled Pre-grouting in Shaft Sinking. By R. H. ALLEN and J. W. GALPIN. 15 ........ Solidifying Mines and Shafts Areas by Pressure Grouting. By B. H. MOTT 17 .............. Grouting in Southeast Missouri District. By W. W. WEIGEL 20] Introduction-Grouting in Mines By definition the word "grout" means a thin mortar, or a kind of plaster or cement, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1947

By P. W. George, G. A. Hellstrand

In 1915, H. A. Guess, Vice President of American Smelting & Refining Co., in charge of its Mining Department, learned that the Anglo-Newfoundland Development Co., Ltd., a pulpwood and paper-mill enterprise, had found upon its large concession in Newfoundland, and had opened up by shaft to the third level and some drifting, a lenticular orebody indicating about 100,000 tons, as an extremely fine-grained sulfide ore, averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn; and that having sent parcels of this ore to Minerals Separation, Ltd., and various other metallurgical testing concerns without obtaining any success in commercial separations thereof, had discontinued work thereon and let the workings fill. Mr. Guess wrote to the general manager of that company and obtained a few hundred pounds of the typical ore, which he sent to his company's metallurgical testing laboratory at Flat River, Mo., outlining various flotation tests desired thereon, in an endeavor to obtain separation into a commercial lead concentrate and a zinc concentrate. But the art of flotation had not then progressed far enough to treat such ore, the galena and zinc blende being so fine grained that grinding to about 300 mesh was required to release the mineral particles in their gangue. Mr. Guess had flotation and other tests continued upon this ore from time to time with whatever new reagents and flotation devices were evolved as time went on, and finally, in 1925, he succeeded in effecting in his company's testing plant, then at Wallace, Idaho, separations into lead concentrates and zinc concentrates of satisfactory commercial grade. Mr. Guess then proceeded to unwater, examine and sample the property and made with the owners a partnership operating agreement upon the mine itself and a considerable area surrounding it, and in the early summer of 1926 began to prospect for additional orebodies, utilizing for such prospecting geophysical methods under the direction of Hans Lundberg, methods which up to that time had been little used in mining in the western hemisphere. This geophysical work found two large flat-lying orebodies of a type precisely similar to the smaller body of the original discovery. The larger orebody, some 3500 ft. west of the original

Jan 1, 1935

By Arthur O. Gates

RittingeR's law of the energy expended in crushing is, as roughly stated by Profcssor Richards,' that the work of crushing is proportional to the reduction in diameter; or, as I have more fully expressed it: "The work done in crushing is proportional to the surface exposed by the operation; or, better expressed for this purpose, the work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product—assuming that all the mass has been reduced to one exact sine, which is only theoretically possible."² Kick's law is stated by H. Stadler as follows :3 "The energy required for producing analogous changes of configuration of geometrically similar bodies of equal technological state varies as the volumes or weights of these bodies." In other words, the energy expended is proportional to the volume reduction, instead of the diameter reduction. That these two laws would give widely different results may be shown by a simple imaginary case. A ton of 16-in. cubes is broken to 1-in. cubes at the first operation, and these are broken to 1/16. cubes at a second operation. Since the first operation produces only one-sixteenth as much new surface as the second, the ratio of energy expended in the two operations would be by Rittinger's law as 1 to 16. By Kick's law, since the volume-reduction ratio is the same in both cases, the ratio of energy would be 1 to 1. This discrepancy is great enough to challenge a test by actual experiment, of which there has been, hitherto, but little compared with the amount of argument. The present paper is the record

Jan 1, 1916

ROBERT PEELE, * New York, N. Y.-I should like to ask Mr. Neale how the members of the production committees at the individual mines, who came from the mine workers themselves, were chosen or appointed; also from what classes of employees they usually came? J. B. NEALE.-In the union fields, they were chosen by a local. In the non-union fields, they were chosen either by the men in mass meeting or by the company officials. The last way was very unsatisfactory because it gave the men an opportunity to say that they were going to be passed upon as to whether they were slackers or not, by men chosen by the company. When they were chosen by the locals or at mass meetings of the workers, the appointments have been very much more satisfactory. R. D. HALL, ? New York, N. Y.-The matter of inefficiency on the part of the operator is one that I think we may well take into account, because there is a very large inefficiency on the part of the coal operator; it has arisen from reasons almost beyond his control and will continue for these same reasons. It is no use arguing a moral responsibility on the part of the operator, when you make efficiency very largely a loss to the operator who puts it in force. If you ask a man working on a clay wage to work with more efficiency. he says, "Well, I may do it or I may not," it all depends how he feels, but he does not lose anything financially by not working hard. If you ask the man who is working by the ton to put out more tons, he makes a profit by putting out more tons. How is it with the operator? If he gives a man all the cars he needs and all the power he needs, if he runs after his working men and waits on them, he does not get his coal out any cheaper than before.. He gives the man a better chance and there is more efficiency, but at the same time he has increased his expenses all along the line. At the end of the year he finds that his profits have been less than if he had had less efficiency. The efficiency is really against him in many ways. Because he gets a larger tonnage, he reduces the overhead to a certain extent; but hiss tonnage may not be any greater because he may work fewer days. As Mr. Taylor remarked some tine ago, supposing he puts in a machine that is very much more effective than any he had before, he has the same scale; the miner gets out more coal, but he himself does not get any benefit out of it because he has a scale fixed, so much per ton.

Jan 4, 1919

By J. M. Stuart, G. D. Bengough, A. R. Lee

Corrosion tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply of oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case of salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion of the metal was shown in some experiments due to Friend.2 He tested the corrosion of mild steel plates immersed in water in glass jars, a steady stream of air being drawn over the surface of the water in the jars. The air passing through half the number of jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor." Conditions for Quantitative Corrosion Tests These results show that we must either control or prevent evaporation at the liquid surface, if we wish to avoid effects on the rate of cor-

Jan 1, 1929

By A. R. Lee, G. D. Bengough, J. M. Stuart

Corrosion tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply of oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case of salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion of the metal was shown in some experiments due to Friend.2 He tested the corrosion of mild steel plates immersed in water in glass jars, a steady stream of air being drawn over the surface of the water in the jars. The air passing through half the number of jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor." Conditions for Quantitative Corrosion Tests These results show that we must either control or prevent evaporation at the liquid surface, if we wish to avoid effects on the rate of cor-

Jan 1, 1929

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.' This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965

By P. E. Baker

The commercial neutron-gamma log measures the intensity of gamma-rays produced by the interaction of neutrons with nuclei in the formation and in the bore hole. This measurement gives information concerning the distribution of neutrons around the neutron source, and in particular gives information on porosity or fluid content. Another type of information is contained in the frequency or energy spectrum of the neutron capture gamma-rays. The capture gamma-rays of each element, in fact of each isotope, have only those energies characteristic of that isotope.'" The neutron capture gamma-ray spectrum, if obtainable, would permit the identification of the elements producing the spectrum. Such information would have considerable value in oilfield exploration work if it could be applied practically in well logging. Experiments have been carried out at the La Habra Laboratory of California Research Cop. to determine the feasibility of a method of well logging in which neutron capture gamma-ray spectra are measured down hole. In these experiments, spectra were obtained for artificial formations under simulated borehole conditions, using actual borehole geometry. This paper will describe the experimental apparatus and methods and will present the spectrum curves for several formations. THEORY Basic Formulas The neutron capture cross section of an element is a measure of its tendency to capture neutrons. The macroscopic cross section, or cross section per cubic centimeter, of a material composed of several elements is the sum of the cross sections of the nuclei making up 1 cc of the material. This is expressed in the equation SB = Sn1s2, ..........(1) where SB is the macroscopic cross section, s, is the cross section of a nucleus of type i, and ni is the number of nuclei of type i/cu cm. If N is the number of neutrons absorbed per second by the composite material, then the number captured by element j is Ni = N nisi/SB = N nisi/Si ni si ......(2) When the nucleus captures a neutron, a new nucleus is formed, which is usually in an excited state and falls to its ground or unexcited state by emitting one or more gamma-ray quanta.* The emission spectrum has been measured for many elements (see Table 1). The intensity of gamma-rays produced by an element is proportional to the number of neutrons captured per unit time by the element, which in turn depends on the capture cross section of that element and the capture cross sections of the other elements present which are competing with the first element for thermal neutrons. In a small sample of material the number of neutrons, N, captured per second is N = ?SB, ..........(3) where $ is the thermal neutron flux and SB is the macro-scopic cross section defined above. The number of neutrons captured by element j is N1 = ?ni si = N ni si/SB . ......(4) The number of gamma-ray quanta of energy, E, pro-duced per unit time by element, j, is I(E)=Nni si/SB P(E) .......(5) where P(E) is the emission probability of element, j, for this gamma-ray energy. Borehole Effects The capture gamma-ray spectra of many elements have been measured accurately in academic and government laboratories. These measurements are made on small samples, and from these measurements the emission spectra of the elements are obtained.

Jan 1, 1958

By Joseph G. Franzone, Alan K. Kuhn, Jerry J. Oliver

INTRODUCTION Tailings produced by many uranium milling operations consist of fine sands with some silt and slimes. When fine sandy materials are placed by hydraulic methods behind an impermeable dam, they are deposited in a loose state and some portion remains saturated. These saturated, loose fine sands are highly susceptible to liquefaction, the phenomenon in which a monotonic or cyclic disturbance causes excess pore water pressure and, concurrently, a total loss of strength in the sand. Once liquefied, the fine sand flows, causing collapse of supported structures. The potential for such a liquefaction failure was identified and successfully treated at Sohio Western Mining Company's L-Bar Uranium Operations near Seboyeta, New Mexico. The Sohio tailings dam is an earthfill starter dam with tailings raises constructed upstream of the starter dam crest. Beginning with the start of mill operations in 1976, tailings were deposited hydraulically in the impoundment behind the starter dam. As the tailings level approached the crest of the starter dam, beached tailings were excavated and placed in lifts by a dozer to form two raises above the crest of the starter dam. As the impoundment has gradually filled with tailings, the decant water pond level has risen. Correspondingly, the water level in the tailings dam, upstream of the chimney drain, has also risen. By August 1980, the phreatic surface was above the crest of the starter dam and stability analyses indicated that the tailings dam did not have the safety factor of 1.0, under static loading with liquefaction, implicit in the 1980 New Mexico State Engineer's requirements. The problem related directly to the high phreatic surface in the loose sandy tailings behind a dam structure that was not capable of resisting failure which might develop in liquefied tailings. Two methods of stability enhancement were considered for the Sohio dam. One method was reinforcement of the dam using a clay buttress placed against the downstream slope. The other method was installation of horizontal drains through the starter dam to drain decant water and lower the phreatic surface. Either method would increase the stability of the dam. However, the comparative analysis of the methods indicated that horizontal drainage offered significant advantages in cost and could provide a more direct remedy of the source of the problem, the saturated section of tailings. In addition, a drainage system would be more amenable to modification and more quickly installed than a buttress. On the other hand, a clay buttress could be more directly controlled, would involve routine earthwork, and has successful precedent. Therefore, the buttress approach would involve less risk. After weighing the advantages of both methods and the costs versus risks, the horizontal drainage approach was selected. Consequently, a horizontal pipe drain system was recommended and designed (D’Appolonia, 1981a). This paper describes the design and installation of the drainage system and its initial performance. PIPE DRAIN SYSTEM DESIGN Design Criteria and Parameters To increase the stability of the dam to acceptable levels, the drainage system had to lower the phreatic surface behind the dam to the level calculated to give a minimum safety factor of 1.0 under conditions of liquefaction. In addition, the system needed to be essentially self-operating, easy to maintain, and economical. To accomplish these objectives, the following design criteria were established: 1. The pipe drains must lower the phreatic surface at least 4.3 m (14 ft.) at the midpoint along the dam (the deepest section) and by proportionately smaller amounts toward the abutments to satisfy safety factor requirements.

Jan 1, 1982