Search Documents

By Howard C. Pyle, John E Sherborne

Core analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.' For convenience the subunit millidarcy, or one-thousandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil14-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By Cyril Stanley Smith

Although not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical cónductivity and that it can therefore be calculated from the latter. The Wiedmann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys—particularly those containing nickel—and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only. Previous Work Copper The conductivity of copper has been studied by many observers since the pioneer work of Wiedemann in 1859. The majority of these measure-

Jan 1, 1930

By John V. W. Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese, but taking into consideration the diminishing quality of iron ores and fuels as well as the increasing exaction of specifications for finished products, it may safely be assumed that, high-grade manganese ore will be more and more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits. Sources of Production Russia alone, of countries producing the major part of the world's stee1, has within its geographical boundaries sufficient manganese to supply its needs. The domestic production of England is inadequate and English requirements for high-grade manganese are supplied principally from India. France also draws largely upon India, as it depends upon foreign sources of supply except with respect to a small tonnage of silico-manga-nese and silico-spiegel produced in the Hautes-Pyrénées. Germany and the United States likewise depend upon foreign sources of high-grade ore, though each possesses comparatively large reserves of ferruginous manganese ore and manganiferous iron ore. At present the world demand for high-grade manganese ore is met with ease by the production of Russia, India, Gold Coast and Brazil.

Jan 1, 1927

By Howard C. Pyle, John E. Sherborne

Core analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.' For convenience the subunit millidarcy, or one-thousandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil14-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By E. R. Borcherdt

METHODS and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. EXPLORATION Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. STOPING For many years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1941

By Oliver Bowles

While vast quantities of limestone and dolomite are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little atten. tion compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux " that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

By Howard N. Eavenson

The information contained in the following paper was collected at the request of the U. S. Coal Commission, and is published with the permission of that body and of the various companies furnishing the data. For obvious reasons, the names of the companies are not given. No data were obtained from states south of Virginia or west of the Mississippi River. The data about the amount of labor, in man-hours, required in producing a ton of bituminous coal have been collected with the idea of showing what is being done at some well-managed plants, and not to show the average amount required by all mines, which undoubtedly is considerably higher than the average of the figures shown.* Almost all of the figures were supplied by the various companies in reply to a questionnaire; when they were obtained from other sources the company was asked to verify them. On account of the amount of work required, the data were only requested for one or two months for each plant, and the figures represent in each case a month when the car supply was good and the work was practically steady. In the case of most of the West Virginia and Kentucky mines, these conditions were best met in May and June, 1922. The mines for which the figures are given are arranged by states and as to whether the mine operates under union or non-union or open-shop conditions. The union mines listed are generally considered to be as well-managed as are the non-union ones. The production per month in a few cases includes the amount of slate which is loaded and hauled out of the mine, as of course this requires nearly as much labor per ton as does the coal. These cases are noted. The number of days worked includes only the total time in which the tipple operated; not the number of days on which the mines operated. This makes the output per day appear slightly higher than it should be in

Jan 1, 1924

By James Aston

THREE years ago the writer presented a paper on the trend of development in the wrought iron industry,1 wherein was described a process in the development of which he has been a factor, which at that time had passed through several years of progressive experimental development but which had not then been put upon a commercial scale of operation. The present paper deals with two years of observation and experience in the commercial operation of a plant by the A. A Byers Co. at Warren, Ohio. It will not enter into the controversial field of the relative merit of wrought iron and steel in various classes of service, nor will it elaborate upon the characteristic services or fields of utility to which wrought iron is particularly adapted. It is sufficient to state that the wrought iron industry is upon a substantial basis and that the material finds service in pipe, where its advantages are in superior corrosion, fatigue, welding and threading qualities; in bar iron for staybolts, engine bolts, and rivets, demanding maximum service against corrosion and fatigue; in plates for corrosion service; and in chains, because of welding and shock-resisting characteristics. In short, ability to withstand the stresses of shock and vibration, or the ravages of corrosion, to hold protective coatings, and to give maximum efficiency in welding, are its features of relative superiority. If these features were not well recognized, the wrought iron industry would have shrunk to insignificance in the face of high costs and acknowledged limitations in manufacture. To charge that this industry is built upon a structure of assumption, psychology, and improperly weighed evidence is an impeachment of the integrity or belittling of the powers of observation of users through many centuries of service experiences.

Jan 1, 1929

By R. J. Wagner, G. H. Gronhovd, A. J. Wittmier

The paper describes the results of a series of full-scale boiler tests run to determine the ash fouling characteristics of a North Dakota lignite as a function of sodium content of the coal. Four levels of sodium were investigated and rate of fouling was determined both by boiler performance and by specially constructed probe equipment. Discussed is information on chemical and physical properties of the ash deposits. The vast lignite deposits in North Dakota are becoming increasingly important as a source of low-cost fuel for power generation. A new 200-megawatt lignite-burning plant located near Stanton, N.D., was placed in operation early in 1966. Another 172-mega-watt unit in the same area is scheduled for operation late in 1966, and plans have recently been announced for a 212-megawatt unit to be in operation by 1970. If these plants show good performance, western North Dakota could become a major power production center for a large geographic area in the upper midwest. One of the problems associated with the use of lignite in power boilers is its tendency to form troublesome ash deposits on boiler tube surfaces. This problem varies considerably from one lignite-fired boiler to another and is dependent upon such factors as source of lignite, boiler design, load factor, tube metal temperatures, and soot-blowing practices. This report presents data on sodium content* variation in a North Dakota mine, describes the results of a series of tests performed to determine the relationship between ash fouling tendencies and the sodium content, and tells how the mining company and electric utility have coordinated their operations to reduce the ash fouling problem. GENERAL BACKGROUND Until recent years it was generally assumed that North Dakota lignite from a given mine had qualities peculiar to that mine, but that within the mine, the lignite was quite uniform. In 1959, the Otter Tail Power Co. installed a 53.5-megawatt lignite-burning unit at its Hoot Lake plant, Fergus Falls, Minn. Shortly after the unit was put into operation, it was noted that at certain times under high load conditions, ash fouling problems were quite severe, but not consistent or predictable. Each time fouling occurred in the unit the position of the loading shovel at the mine was noted. Within two years it became apparent that there were certain areas in the Knife River Coal Mining Co. mine at Beulah, N.D., where the lignite apparently had a high fouling tendency for the Hoot Lake unit. Results from analyses of the coal did not show large differences in moisture percentage, ash percentage, heating value, or ash fusion temperature between the highly troublesome and less troublesome coals. After three years of operation, the troublesome areas had been quite well defined and the mining company started a procedure of bypassing these areas when load conditions at the plant were high and then returning to the troublesome areas to load the lignite during the summer months when peak loads were lower. It was noted that the lignite from the areas which caused severe fouling under high load conditions produced much less fouling at the lower summer loads. However, bypassing certain areas in the strip pit caused the mining company to disrupt their continuous loading schedule, which in turn upset their continuous stripping schedule and made for less efficient mining operation. Meanwhile, at the Hoot Lake plant, the number of soot blowers on No. 2 boiler had been increased from 30 to 55, and a very rigorous blowing schedule had been adopted resulting in soot blowers operating at least some part of 21 hrs per day. Fouling problems continued, with a resulting reduction in plant economy and reliability. During this period the Federal Bureau of Mines Coal Research Laboratory at Grand Forks, N.D., had initiated various research programs relating to the study of lignite ash and ash fouling problems. One project was a survey in which full seam samples were obtained from various locations in all the major

Jan 1, 1968

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By C. P. Fiske

THE pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers; and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance? come the condensers, as large numbers are used in the manufacture of spelter, and improvements m quality result in material decreases in working cost. , While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they-are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are concerned. Materials Bond Clay.-The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather -it in the, accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss. of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later), accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is, evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons-with the clay as usually handled.

Jan 10, 1917

By Dr. O’Neil Thomas J., Donald W. Gentry

"We should be concerned about the future be- cause we will have to spend the rest of our lives there. " -Charles Kettering INTRODUCTION Since the early 1970s, there has been no economic phenomenon that has been more widely discussed or experienced in the United States than inflation. Al- though its precise definition and measurement are elusive, inflation has had pro- found and extensive impacts on the manner in which nearly everyone lives. It is painfully obvious to consumers that inflation is characterized by a continuing up- ward spiral of prices. In a capital-intensive industry like mining, those increases can be positively breathtaking. An interesting example is shown in Table 1. Table I shows that on a unit basis, the equivalent 1980 capital cost of Cuajone was over six times the cost of the adjacent and quite similar Toquepala operation completed in 1959. Such sobering statistics weigh heavily on the minds of executives who are contemplating major investments in new mining facilities. In spite of its monumental presence, inflation has usually been either inadequately covered or totally ignored in textbooks on engineering economy. The reasons for this are not entirely clear, but a contributing factor is the inherent difficulty in accurately predicting inflation. However, under certain conditions, inflation may become the most important factor in a mining investment, and it can rarely be safely ignored in capital investment analyses. DEFINING AND MEASURING INFLATION Defining inflation and related terms is relatively easy. Its measurement, how- ever, is the source of almost endless debate in economic and political circles. How- ever, much of that debate is not relevant to the scope of this book, so that only those issues which impact directly on the capital investment decision are covered in this section. Inflation is the general decline in the value of money as measured by what it will buy. It is clear, then, that the rate of inflation varies with the particular currency under consideration as well as the type of goods and services being purchased. One would find, for example, that the general rate of inflation relative to German marks

Jan 1, 1984

By Nicasio del Castillo

INTRODUCTION The tax structure of foreign mining investment into the United States has a significant impact on the financing and the profitability of the operation. For these reasons, it is critical for the foreign investor to develop and implement a well planned tax strategy that will enable its venture to: (1) reduce its U.S. income tax liability (2) lower U.S. withholding taxes when funds are transferred from the United States, and (3) decrease or defer home country taxation on its U.S. earnings ALTERNATIVE FORMS OF INVESTMENT A threshold business and tax consideration is the form in which the investment is to be made. The most common alternatives include: forming or acquiring a U.S. mining corporation, directly establishing a branch mining operation, or entering into a joint venture or partnership with a U.S. mining company. U.S. Corporations The most common structure through which foreign mining companies engage in business in the United States is to form a U.S. mining corporation. Forming a U.S. Corporation. If the investor decides to establish a new U.S. corporation the organization is relatively simple. No distinctions are made in the United States between "public" and "private" forms of incorporation. Minimum share capital is not usually required and share capital may consist of shares with no par value. Since corporate law is the responsibility of the individual states, the foreign investor must choose a state in which to incorporate. If appreciated mining property is transferred to a corporation solely in exchange for stock or securities in that corporation, and the transferors have control of the corporation (defined as at least 80 percent of all voting shares and at least 80 percent of all other shares) immediately after the exchange, no gain or loss will be recognized. However, if the transferors receive cash or other mining properties in addition to stock, any resulting gain may, in certain situations, be taxed to the extent of the cash and the fair market value of other property received. Acquiring an Existing U.S. Corporation. Acquiring an existing U.S. mining corporation is not as straight-forward as forming a corporation. This alternative may be accomplished through either a stock or an asset acquisition. Generally, with a stock acquisition the purchaser inherits all of the business and tax attributes of the former mining corporation. If the investor is able to acquire mining assets, however, the purchaser will usually be able to avoid any unknown or hidden liabilities that could be attached to an existing corporation. Another principal advantage in acquiring assets is that the purchase price may be directly allocated to the acquired mines or other mineral-related assets with the result that the assets' depreciable base may be increased. Assuming the domestic seller and the foreign purchaser can agree, it is generally advisable to allocate the purchase price in the sales agreement to specific individual assets. From the foreign investor's standpoint, it is preferable to allocate the purchase price to depreciable assets such as buildings and equipment versus an allocation to mineral land holdings or intangibles such as goodwill, which are generally not depreciable. It is not uncommon, however, for a seller mining company being acquired to insist for tax reasons that the investor purchase shares rather than assets. If the foreign

Jan 1, 1985

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By J. M. Callow

The selective action of oils for lustrous minerals was first disclosed by Haynes in 1860. In 1885, Miss Carrie Everson elaborated this idea and also disclosed the fact that acid increased the so-called selective action. Her patent called for oils, either animal, vegetal or mineral, also for an acid or salt. The process was tried out on a practical scale in Baker City and Leadville, in 1889, and failed: first, because, as has since been shown, of the unsuitability of the ore to flotation; and second, because the invention was too far in advance of the times. Then followed the Elmore brothers, first with their bulk oil processes and later with their vacuum method. The basic principles of oil flotation were undoubtedly covered by the above inventors, the work done since their time being merely a building up on ground work laid by them. Different kinds of oil, different quantities of oil, and all the varying degrees of agitation, were all exemplified and practiced by them in one phase or another, and the developments that have since been made are but elaborations of the fundamental principles laid down by Haynes, Everson, and the Elmore brothers. In 1902, the Potter-Delprat process was developed in Australia. In this process no oil was used, the mineral being raised by the generation of gas, brought about by the introduction of acid into the pulp. The mineral particles appeared on the surface of the separatory vessel, in the form of a scum or froth, buoyed up by minute gas bubbles attached to them. This no doubt first gave the suggestion of gaseous flotation. In 1902, also, Froment, an Italian, was granted a patent in which he combined violent agitation with oil and gaseous flotation, the gas being generated within the pulp, in much the same way as in the Potter-Delprat process. In the same year, Cattermole came out with a unique method. First, the pulp was emulsified with a small quantity of oil, by violent

Jan 1, 1916

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By N. H. Fisher

GEOGRAPHICAL DISTRIBUTION THE most important known deposits in Australia of what are commonly referred to as the beach-sand minerals are along the most easterly part of the Australian coast, between Southport, 17 miles north of the Queensland-New South Wales border, and Ballina, 50 miles south of the border, and most of the production has come from this area (Fig 1). Smaller deposits are known to occur farther to the south at intervals for several hundred miles, and beaches have been worked at Yamba, 96 miles south and Woolgoolga, 150 miles south of the border and at Swansea, 60 miles north of Sydney. Important deposits have been shown to exist on north Stradbroke Island and others have been located farther to the north, as far as Tin Can Bay at the south end of Frazer Island. (Fig 2). Table I gives the list of operators with the location of their deposits and workings, their approximate maximum monthly capacity expressed in tons of heavy mineral produced by their concentrating plants before separation into individual mineral concentrates, their methods of mining and concentrating the minerals, and the products obtained. This table applies as of June 1948, but all the operators are remodeling or improving their plants and plant practices will be modified accordingly. In addition, active boring campaigns have been carried out by Alluvial Gold, Ltd., of Sydney, in the Cudgen-Cudgera area, and by Zinc Corporation. Ltd., of Melbourne, on Stradbroke Island, and in other places. PHYSIOGRAPHY Submergence of the order of 100 to 200 ft at the close of the Pleistocene period left the pre-existing hills as promontories and the valleys as deep inlets. Wave action has built bay-bars and sandspits in a northerly direction from the headlands, and lakes and marshes have formed between these bars and the initial post-submergence coast line. These lakes and swamps have been or are being filled in by river-borne sediments or wind-blown sand. Beasley1 has presented evidence that suggests a recent emergence of the coast line of about 10 ft. The evidence for this belief is the presence of a black sand seam 1/3 mile inland and 17 ft above sea level (Fig 3), and although it is not entirely certain that this seam is of beach formation and owes nothing to windblown concentration, other evidence supports the suggestion of recent emergence. Such emergence would undoubtedly aid the formation of bars and sandspits and the easterly progress of the beach front, leaving a series of parallel dunes (Fig 4). This belt of north-south coastal dunes ranges up to 1/2 mile in width and as many as 15 lines of dune have been counted (Fig 3). The foredune is generally the highest, up to 25 ft high, and there is in many places a flat platform in front of the dune known as the berm. The dunes behind the foredune are lower and less well defined

Jan 1, 1947

By N. H. Fisher

Geographical Distribution 'he most important known deposits in Australia of what are commonly referred to as the beach-sand minerals are along the most easterly part of the Australian coast, between Southport, 17 miles north of the Queensland-New South Wales border, and Ballina, 50 miles south of the border, and most of the production has come from this area (Fig I). Smaller deposits are known to occur farther to the south at intervals for several hundred miles, and beaches have been worked at Yamba, 96 miles south and Woolgoolga, 150 miles south of the border and at Swansea, 60 miles north of Sydney. Important deposits have been shown to exist on north Stradbroke Island and others have been located farther to the north, as far as Tin Can Bay at the south end of Frazer Island. (Fig 2). Table I gives the list of operators with the location of their deposits and workings, their approximate maximum monthly capacity expressed in tons of heavy mineral produced by their concentrating plants before separation into individual mineral concentrates, their methods of mining and concentrating the minerals, and the products obtained. This table applies as of June 1948, but all the operators are remodeling or improving their plants and plant practices will be modified accordingly. In addition, active boring campaigns have been carried out by Alluvial Gold, Ltd., of Sydney, in the Cudgen-Cudgera area, and by Zinc Corporation Ltd., of Melbourne, on Stradbroke Island, and in other places. Physiography Submergence of the order of 100 to 200 ft at the close of the Pleistocene period left the pre-existing hills as promontories and the valleys as deep inlets. Wave action has built bay-bars and sandspits in a northerly direction from the headlands, and lakes and marshes have formed between these bars and the initial post-submergence coast line. These lakes and swamps have been or are being filled in by river-borne sediments or wind-blown sand. Beasley1 has presented evidence that suggests a recent emergence of the coast line of about 10 ft. The evidence for this belief is the presence of a black sand seam 1/3 mile inland and 17 ft above sea level (Fig 3), and although it is not entirely certain that this seam is of beach formation and owes nothing to windblown concentration, other evidence supports the suggestion of recent emergence. Such emergence would undoubtedly aid the formation of bars and sandspits and the easterly progress of the beach front, leaving a series of parallel dunes (Fig 4). This belt of north-south coastal dunes ranges up to 56 mile in width and as many as 15 lines of dune have been counted (Fig 3). The foredune is generally the highest, upto 25 ft high, and there is in many places a flat platform in front of the dune known as the berm. The dunes behind the foredune are lower and less well defined

Jan 1, 1949