Search Documents

By C. T. Butler, W. W. Kay, R. D. Boddorff, R. L Ash

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

NEW MEMBERS The following list comprises the names of those persons who became members during the period Mar. 10, 1916 to Apr. 10, 1916. ALLEN, P. R., Pres., McAlester Coal & Coke Co., Knight Templar Bldg., McAlester, Okla. BERNARD, CLINTON PERCIVAL, Min. Engr., Care Forminiere Mission Kasai, Tschikapa, Congo Belge, W. Africa. CARPENTER, GEORGE 0., Vice-Pres National Lead Co. St. Louis Mo. CLARK, WILLIAM ANDREWS, JR., Min. Engr., Pres., Elm Orlu Mining Co., Butte, Mont. CLAYTON, CHARLES YANCEY, Asst. PrOf. of Metallurgy and Ore Dressing, Missouri School of Mines, Rolla, Mo. COHEN, JULIUS MILTON, Mgr. Croesus Gold Mines, Ltd., Matheson, Ont., Canada. CRAMER, WILLIAM BRONSON, Met. at Concentrator, Old Dominion Copper Min. & Smelt. Co., Globe, Ariz. DAHL, SIMEON H., Mill Supt., Messina Transvaal Dev. Co., Messina, Transvaal S. Africa.

Jan 5, 1916

By R. E. Zinkham, R. J. Goodwin

A mathematical study has been made of the amount of support a cement sheath could provide to casing cemented into the earth. Several assumptions were required to make the analysis, but only two of them are limiting: (I) the pipe must be completely surrounded with cement, and (2) any mud filter cake between the cement and formation has the same physical properties as either the cement or formation. The calculations showed that little support would be provided to the pipe before an unsupported cement sheath failed in tension; however, when the cement is confined between the pipe and wellbore and is loaded in compression, the pipe could receive a considerable amount of support. In fact, the theoretical results indicate the lower grades and larger sizes of pipe could have their working pressures doubled when reasonable compressive loads were applied to a surrounding cement sheath. These data are shown in six charts. Other down-hole conditions such as setting the cement under pressure, increased temperature and cement confinement all tend to increase the potential usefulness of the sheath. Because of size limitations, a laboratory program to verify the most important results of this mathematical study would be very difficult. However, small-scale field tests would be practicable. This paper shows that, if a solid cement sheath can be obtained in the field by either primary cementing or by repair after detection of flaws by surveys such as the new cement-bond logs, the use of this approach to reducing pipe costs merits further consideration. INTRODUCTION A modification in casing design practices is proposed which may either reduce the amount and grade of steel required to contain a specified internal pressure or permit the working pressure to be increased for a specified weight and grade of pipe. One of the more important considerations in casing design is its resistance to collapse; however, Bowers' and, more recently, O'Brien and Goins' have shown many casing programs are unnecessarily conservative in this respect, and they have indicated how savings can be made by designing for more realistic down-hole conditions. Earlier, Saye and Richardson howed that pipe costs could be reduced by considering the cement sheath as a part of the casing string when collapse resistance was being calculated. More recently, Rogers4 has raised the question as to whether a cement sheath might be considered in the design for burst resistance of the cemented casing. Calculations have been made for the increased burst resistance a cement sheath would provide for casing in a wellbore, and the results show that a sizable amount of support could be obtained in some instances. These data are presented in addition to a discussion of several other factors that are considered to affect the burst strength of pipe supported by cement. Two types of support are treated: Case I for tensile loading of the unconfined cement sheath, and Case for compressive loading of the confined cement sheath. ANALYTICAL TREATMENT AND RESULTS CASE I—TENSILE STRESSES IN AN UNCONFINED CEMENT SHEATH Conditions like this would most likely occur in a greatly enlarged portion of the hole where the cement was not in immediate contact with either the formation or a thin and hard mud cake. The mathematical analysis for this condition, as shown in the Appendix, rests on the following concepts. Pressure inside a unit length of pipe causes: (1) a tensile or tangential stress to be exerted over the longitudinal cross-sectional areas of the pipe and cement; and (2) an equal amount of strain in both the pipe and cement that is uniformly distributed over the wall thickness of each. This analysis was then used to make several calculations for a cement sheath around 51/2-in. OD pipe. The results are illustrated in Fig. 1, which shows that a tensile stress of 500 psi is imposed on a 5-in. thick sheath when the casing contains a pressure of only 1,450 psi. It also shows that a 10-in. thick sheath would be stressed to 500 psi in tension when the pipe contained a pressure of only 2,350 psi. Alternatively, if the stress analysis is made by means of the Lame thick-wall cylinder theory, the inner fibers of the 10-in. thick sheath will be stressed to 500 psi in tension when the pressure in the pipe is only 990 psi. This, of course, reveals that an unconfined sheath is of little support to the pipe in burst; however, an entirely different result is obtained when the cement is confined between the pipe and formation.

By H. A. Dierks

PENNSYLVANIA's anthracite region lies in the heart of the richest and most densely populated area of the U. S. Nearly 70 million people live within a radius of 500 miles, in which 130,000 manufacturing plants employ more than 8 million workers. The region comprises some 3000 sq miles and contains 484 sq miles of coal measures, which folding and erosion have divided into four separate and distinct fields, known as the Northern, Eastern Middle, Western Middle, and Southern. One million people live in the anthracite region proper, and their prosperity depends to a great extent on the anthracite industry, which produces more than $200 million in new wealth for the U. S. each year. Nearly 80 pct of the tonnage shipped out of the region is handled by nine railroads, which depend on this traffic for a large part of their revenue. It follows that the economic health and the very existence 0: this industry is of real concern not only to the region itself but also to the state of Pennsylvania and the country as a whole. Anthracite mining is one of the oldest mineral industries in America. About 1760 burning rock or stone coal was discovered on the hillsides of northeastern Pennsylvania. Within a few years a systematic search for coal bed outcrops was under way, and hand mining was begun. At first production was very limited, since anthracite was difficult to burn and was not readily accepted as a fuel. Pennsylvania anthracite is one of the densest and hardest of all coals, and its content of volatile matter is low. Consequently it does not ignite easily and it burns without smoke. About 1808 Judge Fell of Wilkes-Barre burned anthracite in an open grate fireplace and demonstrated proper handling of an anthracite fire. From

Jan 1, 1958

THE record of the development of physical metallurgy since the founding of this Institute embraces by far the greater part of physical metallurgy as this subject is recognized today. Yet it is not to be supposed that the metallurgist interested in the properties and behavior of solid metals at the beginning of this period was without important and even fundamental information. He had an empirical knowledge of the behavior of solid metals which extended backward into prehistoric times and he had the early beginnings of many of the chapters in the science of metals. Industry was burgeoning in many directions, for methods had been developed, especially in the manufacture of steel that provided materials in extremely large tonnages, permitting applications of metallic materials on a very widespread scale. These multitudinous new uses of metals created an increased interest in the behavior of metals, and provided the basis for the rapid development of a science of metals. Indeed, the development of science generally that accompanied the industrial revolution reached a flood tide toward the end of the century, furnishing the metallurgist basic principles in chemistry, physics, mechanics, and crystallography that would shortly be extensively applied to metallic behavior. In this account, the early developments in the wide metallurgical field will be traced, in order that the status of physical metallurgy in 1871, when this Institute was founded, may be clearly seen. The subject of metallurgy in antiquity has been written upon frequently and at length. We shall here no more than indicate the main features that we need to define the position in 1871 and to provide a proper background for discussing subsequent developments. The writings of Pliny,1 23-79 A.D., to which Robex-ts-Austen3 fre-

Jan 1, 1948

[ ] S. H. Ash (Mining Industry Continues with Lower Fatal-Injury Rates, P. 257) was born in Roslyn, Wash. and attended Lehigh University and University of Washington. He received a B.S. and E.M. degree in mining engineering. Mr. Ash was supervising engineer in charge of work of Safety Div., Bureau of Mines, eastern Pennsylvania and the states of N. Y., Del., N. J. and the New England states. He was appointed chief engineer of Metal and Nonmetal Mining Section of the Mineral Production Security Div., Bureau of Mines, July 1942. At present he is chief engineer, Safety Branch, U. S. Bureau of Mines. Besides holding membership in AIME, he is a member of National Honorary Engineering Society, Society of American Military Engineers, Tau Beta Pi and many other societies.

Jan 1, 1952

By T. S. Maio, J. G. Mansanti

In 1978, Ozark Lead Co. made the decision to expand the capacity of its mine/mill complex by 33%. The objectives of the expansion were to increase mine production capacity by 1.8 kt/d (2000 stpd), increase lead metal production by 21.8 kt/a (24,000 stpy), and to construct new facilities and modify existing equipment to accommodate increased production. This paper gives a brief explanation of the equipment installed and the overall production and metallurgical benefits realized from this expansion. The expansion was completed in the second half of 1980 with all equipment debugging and fine tuning completed by the first quarter of 1981. Concentrator modifications and improvements were basically restricted to four areas: materials handling, automation of the mill grinding circuit, increased flotation capacity, and concentrate dewatering.

Jan 1, 1985

By Thomas M. Drown

At the meeting of the Istitote in New York, in February, 1880," I described a process of determining sulphur iu metallic allphides, with especial reference to the determination of pyrites in coal. The procem, as then described, is as follows: A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromiue is used it must be neutralized by the addition of a little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.e. of this solution autl heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then

Jan 1, 1881

By D. W. Frommer, M. M. Fine

Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.1 The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.2 The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's 3. At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's.

Jan 3, 1959

By H. Scott

SINCE Böhler discovered, in 1903, on cooling certain alloy steels, the phenomenon of a new and lower temperature transformation than the usual Ar3_2_1 obtained by increasing the maximum temperature to which the material was heated, much has been published' connecting this phenomenon with a large number of dissimilar steels of high alloy content. From the fact that the transformation divides itself, taking place at two widely separated temperatures, it has been called a "split transformation." The, significant facts established by recent investigators' are: that when the' transformation occurs at the higher temperature Ar', troostite or a decomposition product is formed, and that when the transformation occurs at the lower temperature Ar", the resulting structure is martensite. The terminology Ar' and Ar" adopted here is that of Portevin.3

Jan 2, 1919

By K. E. Merklin, F. D. DeVaney

In the past most of the research in pelletizing has as its aim the production of a physically strong pellet. Now that this problem is solved, more attention is being paid to uniformity in grade and chemical composition. Consideration has been given in recent years to a study of additives which will make pellets partially or fully fluxed. Blast furnace tests show fluxed pellets to have advantages over both fluxed sinter and acid pellets. Lower slag volumes are used more frequently in the blast furnace and the uniformity of the charge, both physically and chemically, is becoming increasingly important. A considerable improvement can be secured by having all of the flux uniformly distributed through the pellets in a calcined state. A fluxed pellet, therefore, should be a superior product. The use of an ore burden that contains an appropriate quantity of fluxing materials is not new to the blast furnace industry. For years the Minette ores of France and Germany, the Clinton ores of the Birmingham, Ala., areas, as well as others, which are low in iron but contain calcium carbonate in sufficient quantities to give them self-fluxing properties, have proven economical. The adaption of the sintering process to the preparation of ore burdens provided a means for artifically associating the fluxstone with the iron ore prior to charging to the blast furnace. In 1944 Torpl discussed the effects of using lime in sinter made in Sweden on the sinter's metallurgical performance in a blast furnace. Hessle2 reported in 1945 on the advantages of using lime in sinter to increase the sintering plants' capacity and reduce fuel requirements. Robinson3 discussed the use of lime in Swedish sintering practice at the 1950 Blast Furnace, Coke Oven, and Raw Materials meeting. One of the suggested advantages was the combining of lime with silica to prevent the formation of a fayalite slag, which is difficult to reduce in the blast furnace. Nilson4 at the same meeting commented briefly on experimental work that had just started in the U. S. on the use of lime in sinter. The literature tends to indicate that most of this early work was directed towards improvement in sinter physical quality, and the fact that the feed to the blast furnace was partially fluxed was incidental. It was not long, however, before blast furnace advantages were being claimed. The matter was forcibly called to the attention of North American operators by reports of remarkable production records established by the Russians using fluxed sinter. The leading step was taken on this continent by the Steel Company of Canada in 1957; McMahon5 reported on the marked improvement in performance of an 18-ft blast furnace using fluxed sinter at its Hamilton works. Other North American operators quickly followed theStelco lead.

Jan 1, 1963

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The mechanical properties of Ti-C and Ti-C-0 alloys can be altered by heat treatments to dissolve or reject carbon from solid solutions. The maximum strength is obtained by annealing just below the peritectoid temperature. Quenching from the ß-carbide field results in softening. Impact behavior is influenced by the extent of solution of interstitials CARBON is not as important in titanium alloys as it was in earlier years when graphite induction melting was more prevalent. With induction melting, carbon pickup is about 0.5 to 0.8 pct. Cold-mold arc melting with graphite electrodes, which is among the more current methods, results in carbon pickup of 0.1 to 0.2 pct. The titanium-sponge melting stock itself contains about 0.02 to 0.07 pct C, picked up from the magnesium used in the reduction process. Thus, carbon is still one of the more important contaminants in titanium and needs careful study and evaluation in order to understand titanium and titanium alloys. Moreover, it is equally proper to consider carbon as an alloying addition because, in controlled amounts in titanium alloys, it may serve a most useful function. This is particularly the case where the ultimate in toughness is not required. The addition of carbon to titanium results in a peritectoid-type system as illustrated in Fig. 1. The solubility of carbon is seen to be higher in the a phase than in the ß phase in the temperature range of interest. Below the peritectoid temperature, the solubility of carbon in a titanium decreases with decreasing temperature. This type of system permits many microstructural and heat-treatment variations which may influence the properties of the alloys. The study of how the microstructure variations affect mechanical properties is described in this paper. Experimental Procedures The experimental techniques and testing methods used in this work were the same as those described in detail in a previous paper.' No further descriptions will be given except where changes have been made. High purity iodide titanium, produced by the New Jersey Zinc Co., was used in all of the alloys. Carbon additions were made using high purity spectro-graphic carbon electrodes in order to obtain the highest purity carbon available. The alloys were prepared by double arc melting to reduce the possibility of segregation. The alloys were forged at 875°C to ¾ in. round, descaled, vacuum annealed for 5 hr at 900°C to remove the residual hydrogen, and swaged to ¼ in. round at 750°C. All heat treatments were made on material in this initial condition. Two of the early Ti-C ingots were found to have been contaminated in melting. Vacuum-fusion analyses showed that the two contaminated alloys had picked up oxygen, so the test results on these two alloys permitted an evaluation of ternary Ti-C-0 alloys. A list of the alloys and their compositions are given in Table I. Properties of Ti-C Alloys In a peritectoid-type system, such as the Ti-C system, the chief microstructural variable which influences the properties is solid-solution strengthening. For a given composition, it is possible to control the disposition of carbon, either in solid solution or as the compound Tic, by suitable heat treatments. When in solid solution, the carbon present in the alloy makes a definite contribution to the strength of the alloy. However, when present as Tic, it has very little effect on the strength. Other microstructural variables considered in this investigation were transformation structures and grain size. As discussed in subsequent sections, these variables have only a minor effect on properties as compared to the solid-solution effect. Solid-Solution Strengthening: The principal strengthening mechanism for Ti-C alloys has been found to be solid-solution strengthening. Carbon in interstitial solid solution strengthens titanium, but has very little strengthening effect if present as the compound. Since carbon has a higher solubility in

Jan 1, 1956

Striving to do a better job of ad- ministering the letter and spirit of the Federal Coal Mine Health and Safety Act of 1969, the Interior Department recently invited criticism-and got it. The criticisms were voiced on July 1 and 2 at the first of a series of public meetings being held by the Office of Hearings and Appeals at the Department's behest. Later meetings, at which all interested parties are invited to comment, are to be announced in the press and the Federal Register. Persons wishing to participate in the meetings should contact the Director, Office of Hearings and Appeals, 1015 Wilson Blvd., Arlington, Va. 22203. At the first Hearing, USBM Director Elburt F. Osborn outlined the progress his agency has made to date in implementing the law on three fronts: enforcement, education and research. Since the Health and Safety Act became law on December 30. 1969, he said, the Bureau's force of inspectors has grown from a mere 300 to almost 1100, while mine inspections have increased from 10,265 in 1970 to 11,021 for the first six months of 1971. On the educational front. Osborn said, the Bureau now has some 60 instructors who have trained about 50,000 miners in safety procedures since March 30. 1971. Classes at the new Federal Mine Safety Academy for both government and industry personnel begin on September 1, 1971. he added. Health and safety re- search, meanwhile, has been allot- ted $20.1 million for the 1971 Fiscal Year. Of this, $8.1 million is assigned to the Bureau and $12.3 million to contracts with universities and private companies. Admittedly, Osborn said, the mine fatality rate is still unacceptable, hut it was lower in the first half of 1971 than ever before---0.73 per million man hours and 0.31 per million tons of coal.

Jan 1, 1971

By George A. Bell

The mine and milling plant of Demonstration Gold Mines, Ltd., is near the city limits of Baguio, Mt. Province, P. I. The mine road connects with the main highway to Manila. The nearest railway point is near sea level, approximately 40 miles distant. The Baguio district is very mountainous and has one of the heaviest rainfalls in the world. It is therefore difficult to maintain roads or to impound tailings and mine dumps. All supplies are trucked into the district direct from Manila or the nearest railway point, which means uncertain deliveries and high freight rates. Installation of equipment is difficult and costly. The average elevation at the mine is 4000 ft. and the climatic conditions are ideal except for a three months rainy season. The company generates its own power for mining and milling operations with three 400-hp. Ruston Diesel engines direct connected to 250-kw. General Electric alternating current generators. Labor conditions have been excellent, although at present social security laws are causing some unrest. Labor receives a higher average wage rate in this district than other labor in the Islands. The company also furnishes free living quarters, hospitalization and workmen's compensation. Taxation has been reasonable up to the present time, but some of the new mining legislation may make it difficult to operate and pay dividends. The future depends largely upon the continuation of $35 gold and the political outcome in the Islands. History The Demonstration ore body was worked by the Igorots for many years, as evidenced by old stopes and fill encountered in present operations. Attention of Americans was first attracted soon after the Spanish-American war. During the building of the Benguet road to Baguio, the engineers and foreman became interested in the geology of the district.

Jan 1, 1939

By John Fulton

THE increase in the production of iron has been accompanied by a growing demand for an improved quality, and more especially at the present time, in the manufacture of Bessemer steel, which is rapidly becoming an important branch of industry. This has led the makers of pig iron to a careful investigation of the composition of the materials from which their metal is produced, the inquiry being greatly assisted by a cordial alliance of science and practice. Formerly, chemical science was held in abeyance, or admitted in a hesitating experimental way ; but now it is received as a valuable auxiliary, and its decisions are accepted as final and conclusive. It is called on to assist the iron-maker in determining the quality of his stock, and to detect the presence of injurious elements in his fuel, ores, flux, or iron. The object of this paper is to submit the method now in use at the furnaces of the Kemble Coal and Iron Company in the Broad Top coal and iron region, for removing, by a process of crushing and washing, slate and other impurities from coal, designed, when coked, for furnace fuel. It is not contemplated to claim very advanced progress in this work, believing that it is susceptible of improvement, but to show that some progress has been made in a comparatively new field, and it is hoped in the right direction, since coke is probably destined to become the principal fuel in the metallurgy of iron. The Broad Top coal region occupies an isolated geographical position, standing 25 miles east from the Alleghany field. It is associated with the latter by the structure of its coal, and more closely with the Cumberland field by a similarity in the quality of coal.

Jan 1, 1875

By George A. Bell

The mine and milling plant of Demonstration Gold Mines, Ltd., is near the city limits of Baguio, Mt. Province, P. I. The mine road connects with the main highway to Manila. The nearest railway point is near sea level, approximately 40 miles distant. The Baguio district is very mountainous and has one of the heaviest rainfalls in the world. It is therefore difficult to maintain roads or to impound tailings and mine dumps. All supplies are trucked into the district direct from Manila or the nearest railway point, which means uncertain deliveries and high freight rates. Installation of equipment is difficult and costly. The average elevation at the mine is 4000 ft. and the climatic conditions are ideal except for a three months rainy season. The company generates its own power for mining and milling operations with three 400-hp. Ruston Diesel engines direct connected to 250-kw. General Electric alternating current generators. Labor conditions have been excellent, although at present social security laws are causing some unrest. Labor receives a higher average wage rate in this district than other labor in the Islands. The company also furnishes free living quarters, hospitalization and workmen's compensation. Taxation has been reasonable up to the present time, but some of the new mining legislation may make it difficult to operate and pay dividends. The future depends largely upon the continuation of $35 gold and the political outcome in the Islands. History The Demonstration ore body was worked by the Igorots for many years, as evidenced by old stopes and fill encountered in present operations. Attention of Americans was first attracted soon after the Spanish-American war. During the building of the Benguet road to Baguio, the engineers and foreman became interested in the geology of the district.

Jan 1, 1939

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.' In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer's early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer's direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917

By Samuel S. Arentz, Dorsey A. Lyon

Introduction % •................. 789 The Present Sources of Zinc ..:.......... 791 Zinc Ores.................. 791 Lead-Zinc Ores................. 793 Loss oF Zinc at the Mine.............. 793 Present Method oF Extracting Zinc From Ores....... 795 Class oF Ores Suited to Zinc Retort Smelting....... 795 Concentration Processes Used for Treating Zinc Ores .... 795 Hydro-Mechanical Processes............. 795 Electro-Mechanical Processes............. 796 Flotation Processes............... 797 Losses of Zinc in Lead and Copper Blast-Furnace Smelting .. 798 Possible Future Sources oF Zinc Supply.......... 800 The Problem oF the Metallurgist and the Present Status of New Processes................. 801 Introduction A great deal of attention has recently been given to the metallurgy of zinc, and much of that which has been said and written on this subject has been in the nature of a criticism. For instance, we are quite accustomed to hearing it said that the metallurgy of zinc has stood still, that it is antiquahed, out of date, etc. We are, however, inclined to agree with George C. Stone1 when he says that, although there have been no such spectacular and radical changes as were worked in the metallurgy of copper and iron by the introduction of converters, there has nevertheless been a decided and marked progress in the metallurgy of zinc, and especially during recent years. However, it must be admitted that, due to the fact that the chemistry of zinc is so different from that of the other metals, the retort process is the only process by which zinc is produced commercially; and, moreover, that losses which occur in the zinc industry— that is, in the mining, milling, and smelting of zinc ore—are very great, for it is stated2 that probably less than 50 per cent. of the zinc mined, even

Jan 1, 1915

By W. A. Mudge, Paul D. Merica

One of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of construction. Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid of which the present limitations of design may be overcome. The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion. The corrosion resistance of metals and alloys is never absolute and all-inclusive; a particular alloy will withstand some corrosive conditions well and fail utterly under others. Furthermore, other properties, physical and mechanical, required in conjunction with corrosion resistance vary considerably for different commercial applications. One wants a soft, ductile sheet metal resistant to atmospheric corrosion; another, a high-strength alloy resistant to sulfuric acid. The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys. In June, 1924, a symposium by the American Society for Testing Materials, on Corrosion-resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance was a feature. Today the number of these alloys has been doubled, at least. In addition, economy in design and construction through decreased weight has given considerable impetus to the improvement of alloys of which the mechanical propprties may be improved by heat-treatment.

Jan 1, 1935