Search Documents

By John W. Bell

The aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½-ft. Huntington mill was used.

Jan 1, 1918

By E. O. Wagner, V. F. Parry, W. S. Landers

Development work has shown that the yield of primary tar from coal is proportional to the heat in the volatile matter of the coal and that the yield of tar from noncoking coals may vary from 10 to 45 gal per ton on the ash-free and moisture-free basis. Pilot plant operations have proved that 100 to 135 pct of the bench-scale carbonization-assay yield of tar can be obtained. FOLLOWING investigations by the Denver Bureau of Mines on drying fine coal in the entrained state,'. ' Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help offset the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee," and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal. but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used. Any bituminous material will decompose when heated to about 900°F to yield primary tar, gas, and char. The quantity of tar obtained from various coals depends on their rank and volatile content and to some extent on rate and method of heating. The liquid products derived from thermal decomposition of peat, brown coal. lignites, oil shale, and noncoking bituminous coals can be easily liberated by rapidly heating these materials in a fluidized bed at about 500°C (932°F). Since it takes only a few minutes to heat small particles of fuel to carbonizing temperature in a fluidized bed, processing plants can be built to handle up to 50 tph at relatively low cost. The pioneering development work being conducted at Rockdale, Texas, by Alcoa and Texas Power & Light will solve many engineering problems of such operations. The Bureau of Mines at Denver has studied the carbonizing properties of several hundred coals by small scale assay at 500°C, deriving a simple correlation between the potential yield of tar and the proximate analysis. This correlation, shown in Fig. 1, compares the heat in the volatile matter of the coal with the potential yield of primary tar. The yield of primary tar varies from 12 to 50 gal per ton of pure coal." About the same amount of heat is needed to * MAF equals moisture-and-ash-free basis. distil any dry coal at 500°C, and the time required to carbonize a given particle size is about the same for any coal. It is therefore obvious that coals rich in volatile matter will show the greatest profits when processed. Texas lignites are rich in volatile matter, which contributes some 5700 Btu per lb of MAF coal, and the potential primary tar and oil yield from this lignite averages 12 pct by weight or 27 gal per ton from the pure lignite. Texas lignites are considerably richer in potential tar than lignites of North Dakota and Montana. During 1950 the Bureau of Mines conducted many experiments on carbonizing fine dry coal in the entrained state, publishing a report4 n major features of pilot and commercial-size units required to carry out the process. Additional experimental work has been done at Denver and the pilot plant has been improved, particularly the facilities for studying removal of fine dusts from tar vapors and gases at high temperatures by electrostatic precipitation. A number of materials have been carbonized, including sawdust, peat, brown coal, Brazilian oil shale, lignites, and the lower rank bituminous coals having noncoking properties. Straight coking coals cannot

Jan 1, 1957

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By J. T. Shimmin

THE past twenty-five years has been a period of unparalleled improvement in all lines of mining and metallurgical equipment, but probably none has undergone greater refinement and development than the vacuum filter. Beginning a quarter of a century ago, there has been steady advancement in the art of vacu-um filtration until today its use has become virtually standard practice for dewatering throughout the entire metallurgical industry as well as in important parts of the chemical and industrial processing fields. The credit for the first successful application of vacuum filtration 'at the Consolidated Mercury mines in Utah in 1902 undoubtedly belongs to George Moore. There, it is said, his filter reduced the loss of gold in the slime and sand from $1.25 to 40c. per ton. Successful applications were subsequently made by Mr. Moore at the Liberty Bell mines, Telluride, Colo., the Lundberg, Dorr &Wilson mill at Terry, S. D., and elsewhere. E. L. Oliver is generally credited with, having done the most to work out the necessary continuity of op-eration exemplified in the well-known continuous vacu-um filter which bears his name. Others made improve-ments also, but in my opinion all the new ideas advanced in recent years are modifications of the fundamental principles originated by the two pioneers, Moore and Oliver. Considerable interest has been shown recently in the new type of continuous internal-type vacuum filter which is associated with my own name1. In response to frequent inquiries regarding it and the steps which led up to its invention, I am giving herewith a brief account of the early history of this development and some of the more important installations which have been made during the last year or so. A. M. Nicholas (now deceased), an Australian engi-neer, conceived the idea, several years ago, of manu-facturing a continuous vacuum filter with the filter medium applied upon the inside of the drum, as con-trasted with existing drum filters in which the medium is applied externally. Nicholas recognized that a ma-chine of this type would be simpler than one with a tank and would overcome some of the difficulties en-countered with tank filters on certain classes of pulps, and he appreciated the value of having filtration take place in the same direction as the gravitational settle-ment of the solid particles in the pulp, the pulp being retained within the drum instead of being held against the outside surface. The ease of starting up after a shut down was likewise realized by Nicholas. It was tried in the United States, but was not entirely success-ful primarily due to mechanical defects.

Jan 5, 1928

By D. S. Eppelsheimer, D. N. Williams

The compression texture of iodide titanium is determined and found to consist of a [0001] texture rotated 15° to 30° from the axis of compression. As the amount of reduction increases, the angle of rotation decreases. The 0001 rotation showed a slight preference for a <1010> rotation axis. RECENT investigation of the cold rolled texture of titanium&apos; has shown this metal to exhibit a new type of rolling texture. This texture can best be described as a (0001) [10i0] with the 0001 planes rotated approximately 30" to the transverse direction around a <10i0> rotation axis. Rather good results in explaining the cold rolled texture have been obtained by other workers&apos; by examination of the tension and compression textures. No information was found giving the tension texture of titanium. Generally the tension texture of a hexagonal close-packed metal is identical with its wire texture. The drawn texture of titanium has been investigatedh nd has been found to be predominately [10?0]. Since this is the common tension texture of hexagonal metals of low c/a ratio, the explanation of the difference between the rolling texture of titanium and the rolling texture of other hexagonal metals is not indicated by examination of the tension texture. Therefore, the compression texture of titanium should be particularly important in the explanation of the unusual transverse rotation of the 0001 planes found in the cold rolled texture. The compression texture of titanium was examined by Yen.",&apos; His results showed titanium to exhibit the usual [0001] texture up to 85 pct reduction. At higher reduction a double texture appeared in which the 0001 planes were rotated from 10" to 30" from the plane of compression. This change in the compression texture seemed unusual since the tendency for hexagonal close-packed metals is to approach the [0001] texture as the idea compression texture. Mechanical twinning generally occurs over a considerable range of reductions beginning at a rather low reduction. The samples used by Yen in his investigations were prepared by two methods. Compression in a testing machine was used up to a reduction of 85 pct. Compression by compression rolling was used at higher reductions. Since the change in texture occurred at the same reduction as the change in the method of compression, a connection between the two seemed likely. To check this possibility and to locate the position of the change in texture definitely, if it was found to exist, the compression texture of titanium was re-examined. An iodide titanium crystal bar (99.9 pct Ti) produced by the New Jersey Zinc Co. and donated by the Titanium Alloy Manufacturing Div. of the National Lead Co. was used in this investigation. Procedure The investigation of the compression texture was carried out in three steps; compression, specimen

Jan 1, 1953

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.&apos; Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.&apos; Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10&apos; psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By Wilbur H. Grant

THE property of the United Comstock Mines Co. lies in the eastern foot-hills of the Sierra Nevada Mountains, in the Washoe mining district of Storey County, Nev. Commencing at the boundary line between Virginia City and Gold Hill, covering all the town of Gold Hill, it extends south to American Flat; the main camp, or the new town of Comstock, the mills, shops, residences of employees, and the main haulage-tunnel portal are located on American Flat. The property extends for about 10,300 ft. along the lode; this covers the southern end of the main Comstock lode, the Knickerbocker branch, and the junction of the Silver City branch with the Comstock lode. Within the property, 5000 ft. of the main Comstock lode is known to have been productive, 1000 ft. of the lode at the northern end of the property is thoroughly developed, and 1000 ft. south of this is partly developed; this leaves about 3000 ft. of the known productive portion that has not been opened up by this company. The northern end of the property, or the Imperial mine, has been intricately developed by five main levels and numerous sublevels. The Yellow Jacket ground to the south has been partly developed by the reopening of three old levels. In addition, the main haulage level is driven from the portal at Comstock for 9250 ft., to the north end of the property; about 5500 ft. of this `is in the foot wall of the lode and parallel to it.

Jan 11, 1922

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin&apos;s "Principles of Mineral Dressing,&apos;16 Wark&apos;s "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.&apos; Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin&apos;s "Principles of Mineral Dressing,&apos;16 Wark&apos;s "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.&apos; Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By L. M. Barker

THE New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. HISTORY Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining operations exposed an adequate tonnage of sulphide ores, a 5000-ton concentrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper.

Jan 1, 1939

By Thomas Bannon

PROSPECTING for oil in Spain has been going on for many years but only in a very haphazard way and without adequate geological or technical advice. Shallow wells have been drilled in several provinces but, for the most part, they have been doomed to failure from the beginning because of unfavorable geological locations, inadequate drilling equipment inexperienced operators, or lack of sufficient capital. Geologists seem to agree that the most favorable chances for commercial fields are in the northern part of Spain where the petroliferous Triassic beds underlie Cretaceous and Tertiary sediments. The prov-vinces of Santander, Burgos, Alava, Vizcaya, Navarra, and Guipuzcoa seem to offer the most promising localities. Several shallow wells have been drilled near Villamartin about 60 Km. northeast of Cadiz. One of these wells produced a small quantity of light oil but was never operated. The Spanish Government has been drilling on a well in this district for some time, using the Russian free-fall drilling system. The present depth is about 3000 meters. Several years ago the Compania Petrolera Franco-Espanola drilled a well to a depth of about 700 meters near Elorrio, province of Vizcaya. A diamond-core drill was used. The well was located on vertical Cretaceous beds near an igneous dike. The same company, in March, 1923, made a new location about 500 meters away from the first well and the same distance from the dike, in beds dipping about 80°, and is now drilling its No. 2 well. The last depth reported was about 200 meters.

Jan 3, 1924

By C. L. Warwick, A. B. Parsons

The papers and discussion appearing in this volume were presented at a symposium jointly sponsored by the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers and held at Philadelphia, Pa., November 29, 30, and December 1, 1944. Late in January, 1944, Lieut. Col. C. H. Greenall, Officer-in-Charge of the Laboratory Division, Frankford Arsenal, Ordnance Department, U.S.A., suggested to the American Society for Testing Materials that it might be a propitious time to arrange for a symposium on stress-corrosion cracking at the Annual Meeting of the Society in June, and agreed to make available a number of papers relating to work being carried out at that Arsenal. The Society&apos;s Committee B-5 on Copper and Copper Alloys, Cast and Wrought expressed keen interest in the symposium, and other Society committees were contacted and agreed to cooperate. Since the subject is one of primary interest also to the American Institute of Mining and Metallurgical Engineers, it was arranged that the two organizations would jointly sponsor the symposium. A Symposium Committee was formed under the joint leadership, for A.S.T.M., of Carter S. Cole, then Chief of the Metals Branch, Conservation Division, War Production Board and now Engineer on the Headquarters Staff of the Society; and, for A.I.M.E., of E. A. Anderson, Chief of Metals Section, Research Division, New Jersey Zinc Co. (of Pa.) and chairman of the Program Committee of the Institute of Metals Division. The Symposium Committee was constituted as follows:

Jan 1, 1945

By H. C. Chang, N. J. Grant, A. R. Chaudhuri

During the creep of coarse-grained polycrystalline magnesium at elevated temperatures, a nonbasal type of slip was found to play an important role in the deformation processes. The nonbasal slip traces were examined metallographically in eight specimens (13 grains) and the observed glide plane located stereographically for each grain. The tests were run at 500&apos; and 700°F at stresses of 148 to 786 psi. Based on these measurements and theoretical calculations, the crystallographic elements for nonbasal slip were determined. WHEN a metal deforms by slip, the conventional appearance of the slip bands on the surface of a specimen is that of straight lines. Such is the behavior of the face-centered-cubic metals, as for example, aluminum. The particular slip system on which slip occurs in these metals is governed by the criterion of resolved shear stress. Work on the body-centered-cubic metals a-iron,&apos;. &apos; molybdenum, and columbium4 has shown that the process of slip is somewhat more complicated than the simple gliding of one close-packed plane of atoms over another in a close-packed direction and that it results in the formation of wavy and irregular slip traces on the surface. The recent reviews and experiments of Vogel and Brick and Chen and Mad-din3 show that, for the body-centered-cubic metals, the resolved shear stresses along the planes and the degree of close-packing do not necessarily determine the slip system. Theirs and other investigations indicate that a complete understanding of the slip process in the body-centered-cubic metals is not yet possible. However, one behavior displayed by all these metals is that the slip direction is invariably one of the close-packed directions <11l>. The wavy nature of the slip-band traces has been explained on the basis of cooperative slip by planes sharing this same slip direction.1&apos;3l&apos; It is generally acknowledged that, when the hexagonal-close-packed metal magnesium (axial ratio c/a = 1.624) deforms by slip at room temperature, it does so by basal slip in the close-packed direction <1I%>. This type of slip has the conventional appearance of straight lines and is governed by the critical shear-stress law. Schmid and coworkers" showed that basal slip was operative in the temperature range of —185" to 300°C (—300" to 572°F). Work by Servi, Norton, and Grant6 has shown that, during the creep of coarse-grained aluminum at high temperatures, new slip systems come into operation. The existence of a new high temperature slip system at temperatures greater than 225 °C (437°F) for magnesium was suggested also by Schmid. This was later indicated by Bakarian and Mathewson&apos; to be slip along the pyramidal planes (10i1) in the close-packed direction <11%>.* They * Mention will be made in the text of pyramidal planes and prismatic planes. The pyramidal planes referred to are the type I. order 1 of the form {10il); and the prismatic planes of the type 1 of the form (10i0). For the sake of brevity, they are termed in the teat as pyramidal (10il: and prismatic (10i0) planes, respectively. Where reference is made to the pyramidal plane type 1, order 2 of the form {10i2), they are referred to as the pyramidal planes of the type (10i2:. observed that this kind of slip resulted in irregular markings on the specimen surface. According to them, a possible cause for the appearance of the markings was due to "limited accessory slip on the pyramidal {10i2) planes." Burke and Hibbard," on deforming a single crystal of magnesium at room temperature, found evidence of slip on a pyramidal plane {1011). They explained it as being due to the effect of grip restraints. It is pertinent to note at this point that, although basal slip has received a fair amount of attention, only two specimens have been investigated, that of Bakarian and Mathewson and of Burke and Hibbard, to establish the elements of nonbasal slip in magnesium. During the study of the deformation mechanisms

Jan 1, 1956

By Edwin Dudley Martin

DURING the past twelve years the iron and steel industry has made a major advance through the development of the continuous wide strip rolling mill. So far-reaching have been the results that not only has a better product been sold at a lower price but this improvement in quality has permitted manufacturers of products using steel to make important savings in the cost of fabrication. The net result has been a better product at lower cost to the consumer without reduction in either employment or of wages paid within the industry. That is why the iron and steel industry is proud of its attainment. Being a basic industry of strategic importance, such an advance in technology has had its effects on our internal economy, our standard of living, and our industrial power as a nation in both peace and wartime.

Jan 1, 1939

By Walter Rose, W. A. Bruce

Improved apparatus, methods, and experimental techniques for determining the capillary pressure-saturation relation are described in detail. In this connection a new multi-core procedure has been developed which simplifies the experimental work in the study of relatively homogeneous reservoirs. The basic theory concerning the Leverett capillary pressure function has been extended and has been given some practical application. Some discussion is presented to indicate the relationship of relative permeability to capillary pressure, and to provide a new description of capillary pressure phenomena by introducing the concept of the psi function. INTRODUCTION For the purposes of this paper the capillary character of a porous medium will be defined to express the basic properties of the system, which produce observed results of fluid behavior. These basic properties may be classified in the following manner, according to their relationship to: (a) The geometrical configuration of the interstitial spaces. This involves consideration of the packing of the particles, producing points of grain contact, and variations in pore size distribution. The packing itself is often modified by the secondary processes of mineralization which introduces factors of cementation, and of solution action which causes alteration of pore structure. (b) The physical and chemical nature of the interstitial surfaces. This involves consideration of the presence of interstitial clay coatings, the existence of non-uniform wetting surfaces; or, more generally, a consideration of the tendency towards variable interaction between the interstitial surfaces and the fluid phases saturating the interstitial spaces. (c) The physical and chemical properties of the fluid phases in contact with the interstitial surfaces. This involves consideration of the factors of surface, interfacial and adhesion tensions; contact angles; viscosity; density difference between immiscible fluid phases; and other fluid properties. Fine grained, granular, porous materials such as found in petroleum reser~oir rock possess characteristics which are expressible by (1) permeability, (2) porosity, and (3) the capillary pressure-saturation behavior of immiscible fluids in this medium. These three measurable macroscopic properties depend upon the microscopic properties enumerated above in a manner which defines the capillary character. Systems of capillary tubes or regularly packed spheres may be thought of as ideal and numerous references can be cited in which exact mathematical formulations are developed to show the relationships governing the static distribution and dynamic motion of fluids in their interstitial spaces. The capillary character of non-ideal porous systems such as reservoir rock also is basic in determining the behavior of fluids contained therein; although, in general, the connection is not mathematically derivable but must be approached through indirect experimental measurement. This paper gives consideration to the evaluation of petroleum reservoir rock capillary character. The methods employed may be applied to the solution of problems in other fields, and the conclusions reached should contribute to the basic capillary theory of any porous system containing fluid phases. In this paper, a modification of the core analysis method of capillary pressure is employed and it is intended to show that the capillary character of reservoir rock can be expressed in terms of experimental quantities. A very general method of interpretation correlating the capillary pressure tests with fundamental characteristics such as rock texture, surface areas, permeability, occasionally clay content and cementation is introduced. Eventually an attempt is made for establishing a method of deriving relative permeability to the wetting phase from capillary pressure data. The experimental evaluation of capillary character must be approached in a statistical manner if reservoir properties are to be inferred from data on small cores. This is implied by the heterogeneous character of most petroleum reservoirs, and suggests that considerable intelligence should be applied in core sampling. Finally, this paper supports the view that once the capillary character of a given type of reservoir rock has been established by core analysis, fluid behavior can then be inferred in other similar rock. Although no great progress has been made in establishing what variation can be tolerated without altering the basic fluid behavior properties, evidence will be presented to indicate that certain reservoir formations are sufficiently homogenous with respect to capillary character that the data obtained on one core will be useful in predicting the properties of other cores of similar origin. Tests have shown that cores under consideration can vary widely with respect to porosity and permeability and still be considered similar in capillary character. EXPERIMENTAL METHODS AND TECHNIQUES Various types of displacement cell apparatus for capillary pressure experiments have been described in the literature. Bruce and Welge; Thornton and Marshall; McCullough, Albaugh and Jones3; Hassler and Brunner; Lever-

Jan 1, 1949

By Walter Rose, W. A. Bruce

Improved apparatus, methods, and experimental techniques for determining the capillary pressure-saturation relation are described in detail. In this connection a new multi-core procedure has been developed which simplifies the experimental work in the study of relatively homogeneous reservoirs. The basic theory concerning the Leverett capillary pressure function has been extended and has been given some practical application. Some discussion is presented to indicate the relationship of relative permeability to capillary pressure, and to provide a new description of capillary pressure phenomena by introducing the concept of the psi function. INTRODUCTION For the purposes of this paper the capillary character of a porous medium will be defined to express the basic properties of the system, which produce observed results of fluid behavior. These basic properties may be classified in the following manner, according to their relationship to: (a) The geometrical configuration of the interstitial spaces. This involves consideration of the packing of the particles, producing points of grain contact, and variations in pore size distribution. The packing itself is often modified by the secondary processes of mineralization which introduces factors of cementation, and of solution action which causes alteration of pore structure. (b) The physical and chemical nature of the interstitial surfaces. This involves consideration of the presence of interstitial clay coatings, the existence of non-uniform wetting surfaces; or, more generally, a consideration of the tendency towards variable interaction between the interstitial surfaces and the fluid phases saturating the interstitial spaces. (c) The physical and chemical properties of the fluid phases in contact with the interstitial surfaces. This involves consideration of the factors of surface, interfacial and adhesion tensions; contact angles; viscosity; density difference between immiscible fluid phases; and other fluid properties. Fine grained, granular, porous materials such as found in petroleum reser~oir rock possess characteristics which are expressible by (1) permeability, (2) porosity, and (3) the capillary pressure-saturation behavior of immiscible fluids in this medium. These three measurable macroscopic properties depend upon the microscopic properties enumerated above in a manner which defines the capillary character. Systems of capillary tubes or regularly packed spheres may be thought of as ideal and numerous references can be cited in which exact mathematical formulations are developed to show the relationships governing the static distribution and dynamic motion of fluids in their interstitial spaces. The capillary character of non-ideal porous systems such as reservoir rock also is basic in determining the behavior of fluids contained therein; although, in general, the connection is not mathematically derivable but must be approached through indirect experimental measurement. This paper gives consideration to the evaluation of petroleum reservoir rock capillary character. The methods employed may be applied to the solution of problems in other fields, and the conclusions reached should contribute to the basic capillary theory of any porous system containing fluid phases. In this paper, a modification of the core analysis method of capillary pressure is employed and it is intended to show that the capillary character of reservoir rock can be expressed in terms of experimental quantities. A very general method of interpretation correlating the capillary pressure tests with fundamental characteristics such as rock texture, surface areas, permeability, occasionally clay content and cementation is introduced. Eventually an attempt is made for establishing a method of deriving relative permeability to the wetting phase from capillary pressure data. The experimental evaluation of capillary character must be approached in a statistical manner if reservoir properties are to be inferred from data on small cores. This is implied by the heterogeneous character of most petroleum reservoirs, and suggests that considerable intelligence should be applied in core sampling. Finally, this paper supports the view that once the capillary character of a given type of reservoir rock has been established by core analysis, fluid behavior can then be inferred in other similar rock. Although no great progress has been made in establishing what variation can be tolerated without altering the basic fluid behavior properties, evidence will be presented to indicate that certain reservoir formations are sufficiently homogenous with respect to capillary character that the data obtained on one core will be useful in predicting the properties of other cores of similar origin. Tests have shown that cores under consideration can vary widely with respect to porosity and permeability and still be considered similar in capillary character. EXPERIMENTAL METHODS AND TECHNIQUES Various types of displacement cell apparatus for capillary pressure experiments have been described in the literature. Bruce and Welge; Thornton and Marshall; McCullough, Albaugh and Jones3; Hassler and Brunner; Lever-

Jan 1, 1949

By C. R. McEwen

This paper presents a technique for calculating the original amount of hydrocarbon in place in a petroleum reservoir, and for determining the constants characterizing the aquifer performance, based on pressure-production data. A method for doing this based on a least-squares line-fitting computationwus proposed by vanEverdingen,Timmerman andMcMahon in 1953. We found that their method would not work when there is error in the reservoir pressure data — even moderate error. The technique presented here appears to give reasonable answers when pressure data are uncertain to the degree expected in reservoir pressure determinations. The major change introduced in the present analysis is to limit the least-squares line-fitting to yield only one constant— the amount of hydrocarbon in place. The water-influx constant is then taken as proportional to the oil (or gas) in place. The constant of proportionality can be computed from estimates of effective compressibility and reservoir water saturation. It is also pointed out that the commonly used least-squares analysis assumes all of the uncertainty to be in the dependent variable. The material balance should be arranged so that this condition is fulfilled if correct inferences are to be made from statistical calculations. Examples are shown of the application of the new technique to gas reservoirs—both hypothetical and real—and to the oil-reservoir example of van Ever-dingen, Timmerman and McMahon. INTRODUCTION The amount of hydrocarbon originally in place in a petroleum resenroir can be estimated by means of the material-balance calculation. Simultaneous observations of pressure and amounts of produced fluids are required, together with the PVT data applicable to the reservoir fluids. If water encroachment is occurring, it is desirable to try to infer the behavior of the aquifer, as well as the original hydrocarbon in place, from the pressure-production data. This imposes additional demands on the method of calculation, and uncertainty in the data can result in large uncertainty in the answer. In addition, if the size of a gas cap is to be established, the whole problem becomes indeterminate, as pointed out by Woods and Muskat.1 Brownscombe and Collins2 simulated a gas reservoir and its aquifer on a reservoir analyzer and derived quantitative information on the effect of uncertainty in pressure and aquifer permeability on computed gas in place. Among the various techniques of estimating the performance of an aquifer, the method of van Ever-dingen and Hurst? based on compressible flow theory, seems to have been the most generally successful (see Ref. 4, for example). In this paper we shall confine ourselves to their representation of the aquifer. In 1953,&apos; van Everdingen, Timmerman and McMahon5 introduced a statistical technique for deriving the amount of oil originally in place and the parameters which describe the aquifer. (We shall refer to this technique as the "VTM method&apos;&apos;, as suggested by Mueller.6) Their example reservoir had no gas cap. It has been our experience that the VTM method gives a reasonable answer when the data are very accurate, but that inaccuracy (particularly in pressure) can cause the method to break down. The effect was first observed in gas reservoirs, but has since been seen in oil reservoirs also. In this paper we present another statistical method which has been successful in achieving a reasonable answer where the VTM method has failed. In the new method, one less parameter is derived from material-balance computations. It is assumed that values can be established for effective compressibility in the aquifer and reservoir water saturation independently of the material-balance calculation. The water-influx constant can then be obtained from these data and the quantity of hydrocarbon in place.

By Charles A. Ashburner

The petroleum industry of western Pennsylvania and southwestern New York lias been one of phenomenal development. Greater and more sudden flucuations hare occurred in the price* of crude oil, and in all the collateral interests dependent upon its production, than in the case of any other mineral product which has been extensively exploited in the United States. This was more particularly so from the commencement of drilling for oil in 1859 down to the end of 1877. The experience gained during these early years has enabled the oil men to operate more intelligently since; the business is not now attended with the hazardous risks with which it is generally credited. The most important questions connected with the oil industry are those of (a) the oil-supply, and (6) the possible ultimate exhaustion of the field. Since 1876 my attention has been directed to the study of the statistics of the product of the oil regions. In January, 1880, in order to slow some interesting points connected with these questions, I prepared a graphic chart which was used to illustrate a lecture on petroleum delivered before the Franklin Institute. This chart was afterwards reconstructed in two distinct forms for publication in the census report. on Petroleum and its Products. These latter I have redrawn in a condensed form, and have extended them to include the statistics up to 1885, for publication in the Transac tions of the Institute, in conjuction with a map of the oil-re&&apos;~IOIIS prepared by Mr. John F. CarII and myself. It is hoped that these illustrations will be found interesting to the members of the Institute, and of practical utility to oil-men, without any extended discussion, since it is my desire to make only such brief references to them and give such additional detailed facts as may serve to make the prominent features understood.

Jan 1, 1886

By Joseph Fry, Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep bandstone in the Elk Basin Field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes. of gas in solution. saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep Reservoir of the Elk Basin Field has unusually varying physiral characteristics, such as a saturation pressure of 1,250 psia and 490 cu ft of gas in solultion in a barrel of oil at the crest of the structure and a saturation pressure of 530 psia and 134 cu ft of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the gas in solution in the oil varies from 18 per cent for oil on the crest to 5 per cent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of the oil in the structure. Many geologists and petroleum engineers have considered that all the oil in a petroleum reservoir has rather uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas; that such is not always so is borne out by the results of the study by the writers. INTRODUCTION The Rocky Mountain region is one in which may be found striking examples of the unusual in oil and gas accumulations, as is evident from the following: The high helium content (7.6 per cent) of the gas in the Ouray-Leadville limestone sequence in the Rattlesnake Field, New Mexico, and gases of similar helium content in other fields; 50" to 55&apos; API gravity distillate in solution in carbon dioxide gas and recoverable through retrograde condensation, in the North McCallum Field, Colorado; the occurrence of gas, oil, or both in closely related structures contrary to the usual concepts of gravimetric segregation: the accumulation of gas and/or oil in structures closely related to other structures that apparently are more favorable but do not contain oil or gas accumulations; the high hydrogen sulfide content (as high as 42 per cent) of the gas associated with oil in some fields in the Big Horn Basin, Wyoming; and the wide range of fluid chararteristics found in the Elk Basin reservoir. Elk Basin, an interesting old oil field that has been producing oil from the Frontier formation since 1915, is situated in a highly eroded basin resulting from the erosion of the crest of an anticline and some of the underlying softer shales. The field came back into national prominence during 1943 when it became known that it was the largest single reserve of new oil discovered in the United States that year. The Tensleep sandstone was found to contain oil in November. 1942, when a well drilled to a depth of 4,538 ft (44 ft into the Tensleep sandstone) flowed oil at the rate of 2,500 B/D. By the end of 1949, 137 oil-producing wells and five dry holes had been drilled, and approximately 32 million bbl of oil had been produced. Approximately 6,000 acres may be considered productive of oil in the Tensleep Reservoir, and estimates of the oil that will be produced average 200 million bbl. The Tensleep Reservoir has further interest because it ha-greater closure than any oil field in the Rocky Mountain region; the closure of the Elk Basin anticline is variously estimated at 5.000 to 10,000 ft. of which the top 2.00 ft of the structure contained oil. SUBSURFACE OIL SAMPLING Fig. 1 is a structural map of the Elk Basin Tensleep Reservoir, on which the nine wells used in this study and the numbers correvponding to the well designations hereafter referred to are shown. Wells 1. 2, 3, 4, and 8 were tested and sampled during October and November. 1943. and Wells 5, 6. 7, and 9 during June and July, 1944. An electromagnetic type sampler developed by the Bureau of Mines and described by Grandone and Cook&apos; was used in obtaining the subsurface oil samples. As the wells were tubed nearly to bottom, the sampler was run as far as possible in the tubing hut never below the top perforations. The following procedure was used in testing and sampling the wells: A well was shut in for at least three days, after

Jan 1, 1951