Search Documents

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

HeRbeRT Haas,—(communication to the Secretary*).—Fig. I plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would be well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that '(two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saying that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the South-, west, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market. The greater number of power plants range in size from 300 to 1,000 hp.; the average size of the central station, on a basis of all central stations in the United States, not greatly exceeding 500 kw.; in these sizes it is hard for steam engines to compete with Diesel engines, unless fuol oil prices are excessively high, and coal prices very low, or the exhaust steam is used for heating purposes.

Jan 1, 1917

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By M. E. V. Plummer, F. E. Beamish, J. C. Hole, J. M. Kavanagh

Prior researches have shown that the iron-copper-nickel content of platinum concentrates may be reduced by carbon to form a collecting alloy for the platinum metals in a manner exactly analogous to the formation of the lead fire assay button. The nature of the iron-copper-nickel alloys with the platinum metals has been investigated. Palladium and probably some of the other platinum metals form solid solutions with this alloy. ONE of the greatest known reserves of the platinum metals is to be found in the nickel, copper, iron sulphide deposits of Northern Ontario. The very large tonnage of copper-nickel ore processed makes the Sudbury district a significant world source of the platinum metals, the latter being recovered as byproducts in the electrolytic refining process for copper and nickel. Chalcopyrite, pentlandite, and pyrrhotite are carriers of the platinum metals;' these minerals contain from 0.03 to 2.0 ppm of the noble metals. The analysis of the above ores for the platinum metals necessitates an initial concentration of the minute quantities present in the ore. The method usually employed involves the extraction of the noble metals by molten lead with or without small proportions of silver. The lead is then separated from the precious metals by cupellation, a process which involves absorption by the cupel and volatilization of lead oxide, leaving the precious metals collected in a silver bead on the surface of the cupel. The collection by lead is probably achieved by a process of dissolution followed by some degree of segregation in the lead alloy since the cold button is seldom uniform in composition. With silver-lead alloys this process of liquation has been used to re- cover pure lead since, during the cooling period, crystals of pure lead separate and silver becomes concentrated toward the center of the solid.' Platinum and gold liquate in a manner similar to silver which may account for the successful recovery of platinum by fire assay even though it is considered insoluble in a solid lead medium. 3 In the case of iridium the liquation process may be a disadvantage in that the iridium may appear in the outer areas of the button and thus be lost mechanically during the handling processes. In any case the deficient alloying characteristics of lead for the platinum metals encouraged attempts to find an improved collecting alloy, and by analogy with aqueous extractions, preferably one in which solid solutions would be readily formed. Since, beyond a certain minimum solute to solvent ratio, the formation of a solid solution is accompanied by a lattice distortion, one would expect some relationship between the atomic diameters of any two metals and their tendency to form a solid solution. In one survey5 the hypothesis was put forward that when the atomic diameter of the solute differs by more than about 15 pct from the solvent, the "size factor" is unfavorable and the formation of a solid solution is restricted. On the other hand, when the atomic diameters are within this limit the size factor is favorable and solid solutions are readily formed, e.g. the transition metals of Group VIII having similar radii form solid solutions over wide ranges of composition.6 Even with a favorable size factor, elements having different crystal structures cannot form a continuous series of solid solutions. Cell dimensions alter as the concentration of the solute increases, causing a

Jan 1, 1962

By W. R. Seyfried

THE problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. THE PROCESS AS PLANNED In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the Company, first drafted a process in July of that year-five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or low-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F), (b) The roasted ore would then be leached with hot aqueous ammonium bisulphate to form a slurry. In this way the

Jan 1, 1947

By Walter S. Lutz, J. T. Griffith

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By J. T. Griffith, Walter S. Lutz

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By J. B. Murdoch, John G. Jackson

The many mechanical, geological, and economic factors which influence the planning of a directional drilling program are thoroughly discussed and analyzed. It is demonstrated that the planning of a directionally drilled multiple-well artificial island location is a complicated undertaking and that it is imperative that complete planning and engineering analysis be undertaken before the program is started. Complete planning is profitable because all of the factors influencing the directional work are in general interrelated and many time compromises have to be made before a harmonious program results. The engineering control necessary to accomplish a complicated directional drilling program is outlined. Various means by which engineering control can be increased, such as cylinder drilling specifications, are given. A hypothetical example is developed for a complete offshore artificial island of ten wells to demonstrate the more important factors involved in the planning. Included with this example are special charts and tables which make more rapid the drafting of directional drilling proposals and maps. Introduction A petroleum engineer must consider many and varied factors when planning a long range directional drilling program for an offshore or inaccessible location on an oil structure. The basic principles of direc- tional drilling planning and operation must be reconciled with his company's drilling practices, and frequently special concessions to standard drilling and production practices should be made. The field techniques and tools used in directional drilling are well known and widely used, but the deliberate, careful planning of a complete directional program is in the main a recent innovation. This development, plus the increased demand for oil resources and the consequent exploitation of inaccessible structures and offshore locations, has placed this problem before many engineering departments for the first time. Directional drilling programs of a very complex and difficult nature have been successfully carried out in the Mid-Continent and Pacific Coast regions. The planning itself of a directional drilling project, however, has not had the careful analysis it deserves and we can reasonably expect widespread future progress along thesc lines. Data and experience gained in these programs by the directional drilling service companies and the oil producers have been studied with the objective of giving the engineer a better conception of the factors which govern the various steps in planning a series of directional wells. The newest engineering procedures are the result of recent careful analysis of years of directional drilling work accomplished under the supervision of directional drilling service companies working with the oil companies. The purpose of this paper is to illustrate

Jan 1, 1949

By B. G. Klugh

The present paper represents a preliminary investigation of the ultimate structure of iron-bearing materials which have been subjected to heat treatment for the purpose of agglomerating the fines, or for chemical changes, or for both. Primarily, the object of this inquiry was to determine the relation of the microstructure of each of these materials to its specific susceptibility to the action in the blast-furnace. It is hoped that this small contribution will serve as a nucleus to a line of research that will throw some light upon the debated questions involved in blast-roasting. Thus far the investigation has been conducted along lines of analogy of known principles, rather than through the application of any well-defined system of microscopic petrography. This is obviously due to the fact that we are dealing with ma-terials which are the artificial products of a new art, rather than with the natural materials from which the essence of the pure science has been evolved. In the limited time allowed for this research, it has been conducted upon those materials the chemical content of which allows of their use commercially in the blast-furnace. The following microphotographs are arranged in the order of the degree of complete fusion to which the mass in question has been subjected, in effectively binding the particles together. A very notable fact here clearly demonstrated is that the degree of fusion to which the material has been subjected is inversely proportional to the reducibility of the product. The characteristic of the material under consideration to which reducibility is almost universally attributed call be progressively traced in the following arrangement, through the identity of the obvious microscopic constituent. Furthermore, the degree of fusion to which a bod? has been subjected is recorded in the presence of resultant products of fusion in that body. Such readjustment is generally apparent

Jan 1, 1914

By J. Ruzicka

In creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently hear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addition to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabricated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment. The Equipment The creep equipment consists essentially of a tank containing a constant-temperature oil bath in which the creep of 14 specimens, loaded by means of levers, is measured by means of one movable extensometer. Figs. 1, 2 and 3 illustrate its general construction and appearance. Constant-temperalure Oil Balh.—A common constant-temperature bath requiring only one temperature-controlling equipment for a number of specimens was chosen as the best means of fulfilling the requirements of low cost and compactness. In addition, this allows the testing of a group of specimens under identical temperature conditions.

Jan 1, 1937

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.' In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.'s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By J. J. Beeson

The second part of the paper includes a detailed account of the processes of secondary-enrichment which have been effective in producing the disseminated ores. While both parts present new features, it is hoped that the discussion on secondary chalcopyrite and bornite may be of interest to those who are engaged in the study of secondary processes in other districts. The excellent work' Economic Geology of the Bingham Mining District, by J. M. Boutwell, was published in 1905. Since that time the extensive development work-surface cuts and underground drifting-of the Utah Copper Co. has made possible the collecting of samples for more detailed microscopic study. The writer has taken advantage of this fact and presents the following work, not as a criticism, but as a' continuation of the work which was begun by Mr. Boutwell. b. Acknowledgments.-The present study was undertaken at the suggestion of Dr. A. F. Rogers; to him, and to Prof. C. F. Tolman and Prof. S. W. Young, the writer wishes to express his thanks for criticism in the preparation of this paper. The writer also expresses his thanks to D. C. Jackling, Vice-President and Managing Director of the Utah Copper Co., for permission to publish this paper, and to William Spencer, D. W. Wadleigh, T. S. Carnahan, J. A. Caulfield, Percy Dayer, and Edward Norsefall, for the courtesies extended to him while a co-worker in the mines.

Jan 11, 1915

By R. H. Jacoby, V. J. Berry

Future depletion performance and ultimate oil recovery from reservoirs producing under volumetric control are often predicted with the aid of a material balance equation. When the reservoir fluid is very volatile, however, certain assumptions implicit in the use of the conventional methods are no longer valid. This is became laboratory differential vaporization test procedures do not adequately represent the reservoir depletion process and the performance of surface separation facilities. In such cases recovery of stock tank oil per unit of pressure decline can be predicted only from a detailed knowledge of the separator conditions and the over-all composition of the fluid entering the wellbore at each stage of depletion. Surface recovery is not simply related to the total quantity of liquid flowing into the well under reservoir conditions. In order to improve predictions for reservoirs which produce volatile oils, a step wise method of calculation has been developed. This method uses relative permeability data and multicomponent flash calculations to predict oil and gas production as a function of reservoir pressure. Calculations are presented for a reservoir containing a volatile crude oil, and predicted tank oil recovery by primary depletion is more than twice that predicted by conventional methods which are known to be adequate for ordinary black crude oils. Calculated maximum produced gas-oil ratio is less than one-fourth of the conventional prediction. Wellstream compositions have also been used to determine variation in stock tank oil composition and liquid content of the separator gas. This information is of particular importance for crude stabilization calculations and for design of gasoline plant facilities to recover LPG and natural gasoline. INTRODUCTION The estimation of oil reserves and the prediction of future recovery performance of petroleum reservoirs is a frequent task of the petroleum engineer. If the reservoir produces under volumetric control, performance calculations for primary depletion are made by combining oil and gas material balances with the gas-oil flow characteristics of the reservoir rock. For black oil reservoirs, the Schilthuis1 type material balance is commonly employed. For gas or gas-condensate reservoirs, where only one phase is flowing under bottom-hole conditions, a more simplified material balance is used. In the period in which these material balance methods were conceived and put into practice, it was common to classify reservoirs according to the type of fluid produced as (1) black oil reservoirs, or (2) gas or gas-condensate reservoirs. Recently, however, deeper drilling and more extensive studies of reservoir fluid properties have led to the recognition of reservoir fluids with phase characteristics between those of ordinary black oils, and gases or gas-condensate fluids. These intermediate fluids contain relatively large amounts of the hydrocarbons ethane through decane and are found in deep, high temperature (250°F) reservoirs. Such fluids are often referred to as high shrinkage crudes or "volatile oils." They are usually characterized by tank oil gravities above 45° API. high solution gas/oil ratios,

Jan 1, 1958

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951

By John W. Chandler

INTRODUCTION Where and how to spend the exploration dollar to net the greatest economic return, has always been a major problem for mining companies. Minerals are being consumed in ever increasing quantitie: throughout the world and the mining industry is being called on to meet this demand. In view of the present world-wide nationalistic trend, it is becoming more difficult to determine where exploration money can be spent most profitably. An exploration project should be evaluated continually--in the beginning, to define economic targets and later to determine, as early as possible, whether a project has a chance of developing into a venture that will make a profit acceptable to top management. At this point, a decision can be made whether or not to proceed with plans to bring in a new mine. Exploration, evaluation, and development, therefore, must be fully integrated in transforming an exploration project into a profitable mining venture. DEMAND FOR LEAD AND ZINC Lead and zinc are metals basic to our economy and the demand for them will continue to rise as the population in the world increases. If the population continues to grow at the present rate, it will about double by the year 2000. The accelerating demand for these metals is shown by statistics. Nearly half as much lead (48%) and more than half as much zinc (55%) have been mined between the two world wars as in all pre- ceding history. (1)

Jan 1, 1970

By C. T. Cox

The title of this short paper necessarily implies that friction articles comprise a distinct and unique field and are different from the other metal-powder articles, such as bearings, electrical contacts, and magnets. However, this distinction is rather hard to define in that it is really one of degree and not Of kind. It would appear that the main distinction is that friction are are articles of rather large pressing area. In other words, they are articles in which the area Of the mold in which the metal powder is pressed is relatively large. Other articles made from meta1 powders are generally of rather small area, usually a few square inches, while in friction articles the area ranges up to several hundred square inches. The satisfactory production of meta1-powder friction articles involves many production problems and a large number Of these are accentuated by the large area' Since it is impossible in the short space of this Paper to describe adequately all the problems involved, I have thought it best to merely mention some Of them and to place particular emphasis upon a problem that is common to all metal-powder articles, although it is of greater importance in the making of friction articles. This problem has to do with the effect On the properties of a friction article of small variations in the composition. However, before discussing the problems, it is probably appropriate that some mention be made of the limitations on the use of friction articles. Most engineers are familiar with the general field that can be characterized as constituted by clutch facings and brake linings, and undoubtedly have heard many stories of how metal-powder friction articles have had a service life 10 times as long as nonmetallic friction materials, and of instances where metal-powder friction articles have operated satisfactorily where no other material could be used. These instances should not be regarded as criteria for the assumption that metal-powder friction articles are capable of universal use in the friction field and will always outperform other materials. On the contrary, metal-powder friction articles are unsuitable for numerous applications, either on a performance or on a cost basis. Metal-powder friction articles will not replace wooden block brakes for wagon wheels nor cast-iron brake shoes for railway car wheels, to mention just two obvious examples. Metallic friction articles cannot be used where they must act as heat insulatorsl for they have a relatively high thermal conductivity as compared with asbestos. This is a detriment in some uses, as in certain airplane brakes having hydraulic actuators provided with rubber seals. The metallic friction material readily transfers the heat developed at the braking surface back through the material to the rubber seal and destroys it. Within its limited field, metal-powder friction material has proved satisfactory, but many problems are involved in the Selection of the proper material to use in an application and in the commercial pro-

Jan 1, 1945

By William R. Webster

In view of the great interest now taken in the tests of castiron and details of foundry practice, with the number of investigators at work, and recent improvements in the methods of research, it would seem that the time is ripe to attempt the solution of some of the many problems with which iron founders have to contend. Recent papers and discussions on these subjects* have opened up s large field for investigation, and have emphasized the importance of many considerations generally overlooked. With the view of promoting a comprehensive and systematic discussion, I have attempted to tabulate, in conveilient form, some of the most important points for investigation, on the general plan suggested, with such good results, by our former President, H. M. Howe, for the discussion on the Physics of Steel, at the Virginia Beach meeting, last year. This table can, no doubt, be modified or enlarged to advantage, and put in shape to serve as a guide or reminder to all who are interested in this line of work. Suggested Lines for Discussion and Investigation. I.—Correspondence between chemical composition and melting point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: I. Cupola mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6. Kind of mould, green sand (under dif- on 1 E. Chill. ferent conditions of ramming, amount F. Residual stress. of moisture, and skin-dried), dry sand, G. Condition and quan loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum,

Jan 1, 1896