Search Documents

By C. A. Heiland

The Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station, whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of LOO meters, as under most circumstances it is difficult to level along a arger concentric circle about the station. Principle of Topographic Correction The principle of all topographic corrections is to assume a homogene-ous compositon of the masses around the station in regard to specific gravity as well as a mathematical shape of the topography. The results become the more accurate the closer this mathematical shape is to the actual configuration of the terrain, but naturally the amount of necessary computation also increases. If a standard correction with fixed dis-ances is adopted, the middle error of this method will, therefore, increase as the irregularity of the terrain. Hence, the application of the torsion balance in mountainous areas may be successful only if the disturbances due to heavy masses underneath the surface are so large as to exceed onsiderably the increased middle error due to rugged topography, or,

Jan 1, 1929

By Herbert Haas

The following notes describe a laboratory for metallurgical chemistry and technical analysis which I built late in 1903, while engaged, as constructing engineer, in erecting a pyrite smelter at the Afterthought mine, Ingot, Shasta county, California. This design partly supplements the paper of Mr. C. H. White, which was presented at the Atlantic City Meeting of the Institute in February, 1904.' The work of a chemist at a busy smelting-plant differs radically from the work of a student, who takes all possible care to have his analysis exact within hundredths of a per cent., and has plenty of time to devote to the operation. The works-chemist, having the shortest time in which to make his determinations, should have a laboratory arranged as conveniently as possible to save time in carrying out his work. By a conveniently-arranged laboratory, I do not mean an elaborately furnished one; but rooms suitably fitted up and supplied with the necessary apparatus to do the work expected from the chemist within the requirements of technical analyses. It is not uncommon at large smelters to have the night ae-sayer prepare 30 or more samples for titration, in time for the

Jan 1, 1905

By B. H. Sage

AN apparatus is described for the measurement of the pressure-volume-temperature relations of pure substances, simple mixtures and complex mixtures with an over-all absolute uncertainty, which is usually not more than 0.2 per cent. The equipment is suitable for studies in the gaseous, two-phase, and liquid regions. The behavior of such systems may be investigated at pressures as high as 10,000 lb. per sq. in. for temperatures between 70° and 600° F. The methods of measurement and the construction of the apparatus are described in some detail. The measurement of the volumetric behavior of multicomponent systems requires the simultaneous measurement of the pressure, volume, temperature and weight of each component of the system. In the present apparatus a sample having constant weight is investigated at a number of independently controlled pressures and temperatures, there-fore it is necessary only to establish the weight of each component added before a given set of measurements. This method is in distinction to that in which the total volume remains constant and the pressure is varied by addition or removal of material, the system having variable weight. An objective in the design of the apparatus to be described was to develop equipment that would yield results involving no uncertainties larger than 0.25 per cent throughout the range of pressures from 150 to 10,000 lb. per sq. in. at temperatures between 70° and 600° F. Although this over-all absolute uncertainty of measurement may not appear to be small, it necessitated care in the plans for control and measurement of each of the fundamental variables. In general, any uncertainty greater than 0.05 per cent in the pressure, volume, absolute temperature or weight of each component was considered undesirable; therefore the attempt was made to obtain a precision of measurement in each case such that the absolute uncertainty would be only half this amount except in certain regions near the ends of the experimental range of the variable under consideration.

Jan 1, 1939

By C. D. Stahl, S. M. Farouq Ali

This investigation attempts to describe and simulate the alcohol displacement process by means of a cell model, as employed in chemical engineering practice. The proposed model is more simple than previously proposed models. and utilizes parameters chosen on a theoretical basis. The model successfully reproduced the formation of the stabilized bank and the breakthrough of alcohol, the latter depending on one of the model parameters, which may be correlated with the length of the porous medium. Moreover, the effects of the phase behavior of the liquid system involved, as observed in experimental studies, were reproduced. Several variations of the basic model were devised and tested on a digital computer. These included the cases in which: (1) the actual value of fractional flow was used in cell-to-cell computations; (2) the number of cells was varied within the same run; and (3) incomplete rather than complete phase equilibrium was assumed within each cell. The proposed cell model clarifies the basic mechanism of the process. Detailed concentration profiles obtained for each cell, for instance, showed the mechanism of bank formation in relation to the phase behavior characteristics. The results obtained indicated a varying degree of phase equilibrium concommitant with changes in the velocities of the phases in an actual alcohol displacement. This condition was approximated by changing the number of cells during the simulation. Interesting information was obtained on the influence of path length on the efficiency of alcohol displacement, which has been the subject of some controversy. Certain limitations preclude the use of the proposed model as a substitute for experimental studies. The results obtained were, nevertheless, of value in interpreting the experimental results. INTRODUCTION During recent years considerable effort has been directed toward an understanding of alcohol displacement, the process whereby oil and water are recovered from a porous medium by the continuous injection of a solvent. The complex nature of the physical process involved has so far defied a complete mathematical treatment. Other methods of approach, amounting to an overall material balance, have been proposed, yielding useful information on certain aspects of the process.1-3 Taber et al, in particular, defined the displacement mechanism in terms of the phase behavior of the alcohol-oil-brine system invoIved.2 Wachmann reported a mathematical treatment of alcohol displacement subject to certain simplifying assumptions? Donohue proposed the use of a "cell model" for simulating alcohol disPlacement.5 The nature of the assumptions involved limited the utility of the model. The present work attempts to examine the variables involved in the simulation of alcohol displacement and discusses several possible versions of the basic cell model. Under certain conditions the model results are similar to the experimental results. In particular, the spontaneous formation of of the stabilized bank and the effects of the system phase behavior were successfully reproduced. PREVIOUS WORK ON CELL MODELS Cell models and the theoretical plate concept are often used in solving chemical engineering problems in which an explicit mathematical solution may be difficult or impossible to obtain. Examples of such applications occur in distillation, gas-liquid chroma tography,6 reactor technology, absorption, etc. In petroleum engineering, such a model was used by Attra7 to describe non-equilibrium gas drive, and by Higgins and Leigh ton8 to calculate sweep efficiency in water flooding. Aris and Amundsen pointed out the equivalence between the diffusion model and perfectly mixed cells connected in series.9 Deans proposed a three-parameter cell model to simulate two-component

Jan 1, 1966

By R. L. Perrine

This paper presents results obtained by consider ation of unstable miscible displacement within a porous medium as a quasi-turbulent displacement process, that is, a process characterized by fluctuations around a simpler, mean flow behavior. The instability usually results from the miscible displacing fluid having a viscosity lower than that of the displaced fluid. Such instability is evidenced in suitable experiments by the presence of viscous fingering. A unified theoretical relationship applicable to both stable and unstable displacement is derived. Parameters in the theory are obtained by empirical means. Although the theory describes an idealized conceptual model, agreement with experiment is quite reasonable up to moderately adverse viscosity ratios, such as 17:1. INTRODUCTION Many experimental studies of miscible displacement in porous media have been conducted with prediction of reservoir displacement efficiency as the ultimate objective. Most such studies have utilized lower displacing than displaced fluid viscosity, scaled to potential reservoir fluid pairs. Theoretical approaches have been largely limited to unit viscosity ratios, however, in spite of the necessity for an understanding of the mechanism of the unstable, adverse viscosity ratio displacement process. An obvious reason is the difficulty of describing in mathematical form the viscous fingering characteristic of these conditions. Observation of experiments conducted with dyed fluids in transparent systems suggests an analogy between unstable miscible displacement and turbulent flow in a pipe. In both cases there are fluctuations around a simpler, mean flow behavior. An important difference is that flow behavior of interest in the porous medium is entirely transient, contained within a transition zone between displacing and displaced fluids. Transient behavior complicates description in that coefficients in the equations become variables rather than constants. In the study reported here, the analogy with turbulent flow has been used in treating unstable miscible displacement as a quasi-turbulent displacement process. The purpose has been to derive, even if restricted to an idealized conceptual model, a unified theoretical relationship applicable to both stable and unstable displacement. A relationship meeting these specifications up to moderately adverse viscosity ratios, such as 17:1, is presented. One fluctuation parameter in the theory and dispersion coefficients are obtained by empirical means. The idealized theory is compared with experimental results. UNSTABLE MISCIBLE DISPLACEMENT AS QUASI-TURBULENT DARCY FLOW The miscible displacement of one fluid by another within a porous medium is considered in this study. Flow conditions are such that Darcy's law is applicable. It is further assumed that, by the stability criterion proposed by perrine,1 initial flow conditions lie well within the regime of instability. Thus substantial viscous fingering is assured. We wish to show how this flow regime can be represented as quasi-turbulent. That is, the Reynolds number for the established flow conditions is below that for inertial or turbulent flow within a porous medium, and lies within the regime for which Darcy's law is valid. Yet flow behavior can be described as the combination of some relatively simple average result, and characteristic fluctuations that are superimposed on the simpler behavior. Stated another way, flow behavior includes the movement of layers of fluids with different velocities past or over one another. Such descriptions are characteristic of turbulent pipe flow. The fluctuations in the present case are a direct consequence of the local viscous fingering which accompanies the unstable displacement process. Should displacement become stable, fluctuations would die out. It is of particular importance to note that fluctuations such as these can interact in a way that contributes to material transport by the basic flow. The basic transport equations required for engineering calculations must be modified to reflect this fact.

By J. E. Johnson

OF the many items of information necessary to the successful management of the blast-furnace, few are more important than knowledge of the location and movement of the stock: line:—whether the furnace is full and has been kept so; whether the stock is settling regularly or slipping; and, if slipping, how often it has slipped, at what times, and how far at each time. To obtain these data, a man is sometimes stationed at the top of a pair of mechanically-filled furnaces, sim-ply to watch and gauge them by hand in the old-fashioned way. A more recent practice is the suspension of test-rods from ropes leading over pulleys to the ground-level, where the ropes are mound on small drums with graduated peripheries and provided with crank-handles, whereby the skip-man or some other person can quickly and conveniently gauge the position of the stock-line in the furnace. I believe the credit for this great improvement belongs to Messrs. McClure $ Phillips of Sharon, Pa., who were, as far as I know, the first to apply it, and who have a patent for it. The valuable indications gained by application of the Uehling pyrometer to the down-comer are not to be ignorcd; but the information thus furnished is somewhat indirect, and there is no scale for the translation of " top-temperatures " into " feet down." Moreover, this apparatus, as a whole, is delicate, and the cost of installation and maintenance is high. If the record furnished by the Uehling pyrometer is not in the most desirable form, the test-rods, on the other hand, give no record at all, except through the memory or notes of a man who, to say the least, is not gauging continuously, and who may omit to report an improperly low stock-line, if it be due to a fault of his own.

Jan 1, 1906

By Henry B. Estabrooks

As was true with many mining companies, the management of Tennessee Copper Co. followed with interest the successful application of AN-FO as an explosive in coal stripping, construction, open-pit mining, and finally in underground salt mines. Since Tennessee Copper's operations required about 1,250,000 lb of dynamite annually, the potential savings in explosives costs that could be realized by switching to AN-FO could not be ignored. From a cautious start, AN-FO is now being used for stoping, development work and secondary blasting in all mines of Tennessee Copper Co. AN-FO accounts for 80% of the explosives used in such work. Fragmentation, fumes, crew acceptance, and cost savings have been quite attractive without any decrease in safety.

Jan 11, 1962

By C. A. Sobotowski, J. Eagan

Computer programs applicable to coal mining have been available for some time, especially in the academic sector. However, the computer has not routinely been applied to actual mining operations. This paper discusses how a computer system was set up as an important tool in mining design and decision making. The project was completed within the allotted timeframe of two months by taking advantage of existing technology. Key points include the selection of programs to meet the specified needs of the project, conversion of the programs to be compatible with a computer of a different manufacture, simplification of the data entry process, development of procedures for using these programs, and an explanation of how the reports generated from the programs were used for mine planning and decision making.

Jan 1, 1983

By R. C. Padfield

Experience over a 3-year period in Bethlehem Steel Corporation's plants has demonstrated the reliability of open-hearth roofs of bonded sprung-arch constructzon with burned basic brick. The design principles lor constructing these roofs include a minimum hot-strength requirement for the basic brick, expansion allowances that extend the full roof thickness, structural members to control arch contour, and a specified minimum roof rise. The greater stability of bonded roofs is explained in terms of the basic stress patterns of ring constrution and bonded construction. PRIOR to the development of successful sprung-arch roofs of basic brick, the majority of open-hearth furnaces in the United States were operated with sprung-arch roofs built of silica brick. Although many silica roofs used on open-hearth furnaces were ring-arch construction, Bethlehem Steel Corp. used bonded-arch construction because of its greater stability. In ring construction, each ring of brick is separately keyed and comprises an independent arch with the straight joints between rings traverse to the longitudinal axis of the furnace. In bonded construction, the bricks are laid in rows starting from the skewbacks so that the straight joints run parallel to the longitudinal axis of the furnace. Each brick in a given row is laid so that it spans the joint between two bricks in the row beneath it. Thus, the transverse joints across the arch are broken and the arch rings are thereby interlocked or bonded. When basic roofs were first being developed, the basic brick that were available had low hot strength. Such brick could not be safely used in sprung-arch construction without some means of suspending them. With the development of higher firing techniques by brick manufacturers and the recently introduced direct bonded bricks with high hot strength, the use of burned basic brick in sprung-arch roofs became feasible. The availability of high hot strength basic brick coupled with the potentially lower cost and proven stability of bonded construction prompted Bethlehem's Research Department to study the possibility of using basic brick in bonded roofs. With the full cooperation of plant ceramic engineers and open-hearth superintendents, particularly in 3 years of fur-nace trials, we developed the design criteria for bonded roofs and the corresponding property requirements for the basic brick that are discussed in this paper. DESIGN PRINCIPLES OF SPRUNG-ARCH BRICK ROOFS Stresses in Fixed Arches. A sprung-arch open-hearth furnace roof is generally built on rigidly held skewbacks. The constraint of the fixed support at each end adds a bending moment to the horizontal and vertical reactions at the ends of the arch. Fig. 11 shows the positive direction of forces acting on an arch fixed at both ends. Fixed arches can be analyzed when the members are continuous and have elastic properties. However, brick are inelastic, and arches built with individual brick segments cannot carry tensile stresses. Therefore, for practical solution of brick arches, empirical formulas have been derived from elastic theory that place design restrictions on arch dimensions to avoid development of tensile stresses. McDowell2 cites three main conditions for stability in sprung brick arches: 1) the thrust line of the arch should be maintained in the middle third of the thickness to avoid tensile stresses and resulting open joints in inner and outer curves of the arch; 2) the angle between the line of thrust at any joint and a line perpendicular to the joint must not exceed the angle of repose between brick; and 3) the maximum pressure at any point must not exceed the strength of the arch materials at furnace operating temperatures. The first and third conditions are particularly important in designing sprung-arch basic roofs because of the comparatively low hot strength of basic brick. According to McDowell's equation, if the thrust line is maintained within the middle third of the arch thickness, the unit pressure is obtained as follows: where p = unit pressure in psi, F, = resultant thrust normal to skewback in pounds per foot, t = arch thickness in inches, and z = distance in inches of thrust line from arch axis. When the resultant thrust normal to the skewback acts along the arch axis, z equals zero and unit pressure is simply the thrust divided by the cross-sectional area. If the thrust line moves to the limits of the middle third of the arch thickness, beyond which tensile forces would develop, z then equals one-sixth of the arch thickness and the unit pressure is double that when the thrust line is acting

Jan 1, 1968

By J. Intrater, E. S. Machlin

In a study of grain boundary sliding in superpure Copper (99.999 pct),&apos; bicrystals of a specific shape were used, Fig. 1. That shape was adopted in order to minimize the deformation of grains on both sides of the boundary due to clamping. Another requirement was to obtain bicrystals with a rnicroscopically straight boundary, Fig. 2. Single crystals of predetermined orientation (growth axis parallel to <310>) were grown in a graphite mold from seed crystals. The apparatus for growing single crystals consisted of a vacuum system, argon purification train, vycor tube (in which a graphite mold was placed), a carriage for the induction coi1,and a Lepel (7-1/2 KW) high-frequency converter. The graphite mold was heated by induction and the charge in turn was heated by conduction. The induction coil was moved by means of a motor at a speed of 1 1/2 in. per hr. Single crystals of two different orientations were grown from the melt in one-half of a split graphite mold, Fig. 3(a). Two such crystals were then placed in contact with each other in another split mold, Fig. 3(b) using tapered inserts. The pair of crystals was then remelted starting 2 in. from the top to insure that the whole top portion of the crystals was maintained molten. By moving the induction coil

Jan 1, 1960

By M. F. Werneke, J. A. Jones

The use of a unique class of sulfhydryl collectors, the monoalkyldithiocarbamate salts (RNHCS2M) as direct collectors for malchite and azurite is presented. Microflotation and laboratory scale flotation tests were performed to define the collector properties of these reagents under a variety of flotation conditions. On the basis of the results, it is proposed that some property of the amine-hydrogen atom in the reagent has a signification influence on the unusual activity of these collectors for oxide copper minerals.

Jan 1, 1979

By G. T. Lineberry, L. Adler

Reduced clearance a one of the most important characteristics of encumbered space in underground coal mining. Another key variable is the maximum velocity at which a piece of mobile mining equipment can operate in this limited space. Typical velocity-clearance curves for different mine transportation systems are developed and characterized. Applications of the relationships are examined, emphasizing their significance in designing and controlling mine materials handling system.

Jan 1, 1985

By E. J. Wasp, T. C. Aude, F. B. Raymer

The following paper deals with technical aspects of terminal facilities for western coal pipelines. The information is taken from the Ohio and Black Mesa pipelines and the proposed one in Wyoming. This paper first discusses the feed terminal, the product that it must produce, and the reasons for coal cleaning. Then in the delivery terminal section, the various methods of dewatering the coal and some recent innovative ideas on bunkering the dewatered product and storing the dewatered coal in large outdoor piles are discussed.

Jan 1, 1979

JamEs F. Kemp, New York, N. Y.:—Mr. Hewett&apos;s paper is one of exceptional interest, because it not only adds an important contribution regarding one of the rarer, valuable elements, but also because it introduces compounds hitherto unknown and in associations no less novel. While we have occasionally discovered and recorded asphaltite in metalliferous deposits, for example in the Joplin and Granby districts, we have not seen a metallic ore in a deposit eesentially asphaltite. The source and method of introduction afford a subject well worth serious reflection.

Jan 1, 1910

By Atsushi Watanabe

Japanese Operations Research Committee for Mining Industry is one of the committees in The Union of Japanese Scientists and Engineers. Members of the committee are Dowa Mining, Furukawa Mining, Mitsubishi Metal Mining, Mitsui Mining and Smelting, Nippon Mining and Sumitomo Metal Mining. This paper is an annotated summary of study reports of the committee.

Jan 1, 1969

By L. D. Wooddy, W D. Moore

Water drives may be natural or artificial. For the case of a natural water-drive reservoir, the volume of water influx corresponding to reservoir pressuve-production history may be calculated by means of the material bal-ance-unsteady state equation. For the artificial water drive or pattern injection water flood, the material balance equation is sufficient to determine the reservoir pressure-production, injection history. However, for both cases to reliably predict reservoir performance, it is necessary to calculate the saturation distribution of the reservoir fluids at different stages of depletion. This paper consolidates the various equations used to determine the performance of water-drive reservoirs into one approach that is applicable to any reservoir that has a natural water drive or is to be produced by water injection. The numerical procedure has been simplified considerably, and the solution is adaptable to either hand calculations or digital computer operation. INTRODUCTION A water-drive reservoir is one in which the predominant source of energy for production of oil results from the encroachment of water into the oil zone. The water drive may be either natural or artificial. Water invasion takes place by expansion of water in the aquifer as a result of the pressure decline transmitted from the oil reservoir. Because water is practically incompressible, a natural water drive requires an extensive aquifer containing a volume of water many times the volume of oil in the reservoir. Provided the permeability of the formation is reasonably high, a moderate decline of reservoir pressure usually causes adequate water influx. If the reservoir pressure decline becomes excessive because of low permeability or a high rate of production, part of the oil production may result from the liberation of dissolved gas which may cause excessive quantities of free gas to be produced along with the oil. In extreme cases, reservoir pressure may decline so rapidly as to cause the oil to be produced predominantly by dissolved gas drive, leading to abandonment of the reservoir before the advancing water has had a chance to flush the entire reservoir. In reservoirs that are not connected to extensive aquifers, an artificial water drive may be created by injecting water into or around the lower edges of a reservoir. Sometimes water is injected within the reservoir through wells interspersed among the producing wells. When injection is carried out in such fashion, the reservoir is in effect subdivided into a number of separate producing segments, in each of which the displacement of oil is simultaneously taking place, and the shapes of which are fixed by the well patterns employed. Because of the natural tendency of oil and water to segregate according to their relative densities, water will tend to migrate downdip regardless of where injected. Accordingly, the injected fluids can be retained within the intended reservoir segments only when conditions are unfavorable to their migration under the force of gravity. Pattern injections are usually confined, therefore, to reservoirs having low structural relief, or low permeability, or when production and injection rates are such that fluid movements in the reservoir are dominated by the pressure gradients rather than by the force of gravity. In the case of natural water-drive reservoirs and artificial water-drive reservoirs in which the water is in-

Jan 1, 1958

By A. T. Sweet, C. E. Plummer, H. W. St. Clair, S. F. Ravitz

The ammonium sulphate process for recovering alumina from clays was proposed by Rinman, Buchner, and others many years ago, and more recently various modifications have been investigated both here arid abroad.l-Is The process, as it is being investigated by the Bureau of Mines, involves the following essential steps: (I) sulphating the alumina in the clay by baking with ammonium sulphate at approximately 4m°C., (2) leaching with water to extract aluminum sulphate and ammonium sulphate, (3) crystallization of ammonium alum, (4) conversion of the alum to aluminum hydroxide by the ammonia gases given off during the baking, and (5) calcining the aluminum hydroxide to alumina. The over-all reaction between kaolinite (the most important alumina mineral in most clays) and ammonium sulphate during the baking step may be expressed as follows: Al2O8.2SiO2.2H2O + 4(NH4)2SO4 = (NH4)2SO4.A12(SO4)3 + 6NH3(g) + SH2O(g) + 2SiO2 [i] There is definite evidence. as is shown later. that the aluminum occurs in the baked product as anhydrous ammonium alum rather than as aluminum sulphate, provided the baking temperature is not much above 4o0°C. It is probable that the reaction takes place in the following steps: (NH4)2SO4 = NH3 -(- NH4HSO4 [2] Al2O3.2SiO2.2H2O + ;}NH4HSO4 = A12(SO4)3 + 3NH3 + 5H2O + 2SiO2 [3] A12(SO4)3 + (NH4)2SO4 = (NH4)2SO4.A12(SO4)3 [4] In onc modification of the process, the ammonium sulphate is first decomposed according to Eq. z, and the clay is treated with the resultant ammonium acid sulphate. Reaction I is highly endothermic. On the basis of the best available data, the following values have been estimated for the changes in heat content and free energy in calories per mol: -AH = 331,040 - 34T -AF = 331~040 - 78.3T log T - 671.8T The heat required&apos; at 25OC is 320,900 cal. per mol, or 5650 B.t.u. per pound of alumina. The theoretical equilibcium pressure of NHa, based on the free-energy equation given above, increases very rapidly as the temperature rises above 3o0°C., and reaches one atmosphere at 43s°C. Ammonium alum solutions are almost ideal for crystallization. A saturated solution of ammonium alum contains 126. grams of AlzOa per 1000 grams of water at 90°C. and only 16.5 at 20 C. Hence most of the alum crystallizes out when the

Jan 1, 1944

By Roscoe C. Clark, Henry F. Coffer, J. J. Reynolds

A cement slurry lightweight additive has been adapted in the Conoco laboratories for use in oil well cements. This additive makes possible the use of air to lighten oil well cement slurries. Specifically, the additive consists of small clay bubbles of air having sufficient strength to resist crushing by bottom hole pressures. Clay bubble cement slurry weights can be safely reduced to 10 Ibs/gal. In addition, the clay bubbles tend to act as lost circulation materials and to provide a cement texture which should produce good perforating characteristics. Clay bubble cement is relatively impermeable. INTRODUCTION In many areas in Oklahoma, Texas, Wyoming, and California, difficulties are experienced during casing cementing operations with lost returns caused by the high density of the cement slurries. Wells in these areas are ordinarily drilled with 9 to 11 lbs/gal. drilling mud while neat cement slurries may range in densities from 14.5 to 17 lbs/gal. In these areas, cement slurry weights are at present being successfully reduced to around 12 lbs/gal. (under bottom-hole conditions) by the use of additives in the cement. Since the use of additives will decrease the strength which the cement will develop, the amount of additives which can be used must be based on the minimum cement strength which is acceptable; and thus the maximum slurry weight can be reduced. At present, the minimum tensile strength generally acceptable is 50 lbs/sq in. cured for 24 hours under bottom-hole temperature. This figure is based on laboratory tests1 and on a large number of cement jobs which have been conducted using cement which will not develop more than 50 psi tensile strength in 24 hours under bottom-hole conditions. Two additives are now in use for decreasing cement slurry weights. These are expanded perlite and/or bentonite. The density of both of these materials is greater than that of the cement slurry; however, large quantities of water may be added with these materials without producing a slurry which will settle out of suspension. It is these large quantities of water which contribute to the reduction in the slurry weight. The minimum slurry weight at present obtainable with expanded perlite and/or bentonite is approximately 12 lbs/gal. using a standard Portland cement slurry. In many areas, this weight reduction is insufficient; and returns are still lost during casing cementing operations. In many cases, the pay formation itself is fractured; and a considerable quantity of this cement is lost to the pay zone. It is therefore believed that if cement slurry weights can be reduced to as low as 10 lbs/gal., two advantages will accrue: 1. The lighter densities (10 to 12 lbs/gal.) should mitigate or eliminate lost returns during casing cementing operations. 2. Cement slurries above 12 Ibs/gal. (the present minimum limit ) should develop considerably more strength than is now being obtained. A tensile strength of 100 psi is desirable.&apos; It is the object of this paper to describe a cement slurry having a weight of 10 lbs/gal. and capable of

Jan 1, 1955

By T. W. Harris

This paper was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the reduction of individual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States in order to consolidate the information developed from the many hundreds of boiler tests on coals consumed by various coal-burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal data, including description of coals used (with sufficient space to include first, second and third preference) on source of coal used, complete analysis and factors affecting choice of coal used. 3. Plant data, divided into: (a,) hand-fired, (b) overfeed stokers, (c) underfeed stokers, (d) traveling grate stokers, (e) pulverized coal; and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency data and remarks. The questionnaire was drawn up by consultation with various combllstion engineers, including B. J. Cross, Test Engineer of the Combustion Engineering Co., W. H. Fulweiler, of the United Gas Improvement Co. and the U. S. Bureau of Mines. In all, 11,538 copies of the questionnaire have been distributed, of which 4369 were sent in duplicate. Our estimate of the total volume of bituminous coal consumed in stationary steam boilers over the 12 months of 1930 is approximately

Jan 1, 1934

By E. Teghtsoonian, K. G. Davis

THE preparation of cobalt crystals offers problems: on cooling through 400°C a phase transformation takes place whereby the structure changes from face-centered cubic to the low temperature close-packed hexagonal form. There are a few references in the literature which describe the preparation of cobalt crystals for magnetic work1,&apos; where melt-solidification methods were used. Reasons will be given why such methods were found unsuitable for our purposes. The following techniques were tried: 1) Solid state methods. Any mechanical shaping of tensile specimens would lead to uncertainty with regard to residual strains. With this in mind, following Kaa, strain-anneal and grain growth techniques were extensively investigated. In no Case were useful single crystals obtained. The transformation boundaries, which are crystallographically similar to twin boundaries, are probably extremely stable and inhibit the grain growth. 2) Growth from the melt. Normal melt-solidification methods were tried, using recrystallised alumina crucibles, and also a osoft moldo technique in which cobalt rod was packed in alumina powder. Trouble was encountered with gas evolution on solidification of the melt, giving porosity. Some adhesion of cobalt to the alumina also took place. Only a small proportion of the runs gave single crystals. 3) Zone-refining. Much the best results have been obtained using an electron-beam floating zone refiner. The refiner, based on a design by Calverly et Al .5 had a single-turn tungsten filament. It was operated at 600 v with an emission current around 45 ma. Commercial cobalt rod 1/8 in. in diam was given one pass at a rate of zone travel normally 25 cm per hr, under a vacuum approximately 10-5mm of Hg. Over 50 pct of the runs gave long sections of single crystal. Crystals up to 2o Cm long with good uniformity of cross section and straightness have been grown in this way. Increase in the length of the molten zone resulted in higher single-crystal yields, but control of zone stability was reduced. Sub-boundaries in the zoned crystals were few, and Laue X-ray spots were sharp. The success of the method is believed to lie in two factors, namely i) the absence of crucible restraints during the transformation, and ii) extreme axiality of heat flow during cooling. The axes of the zoned crystals were clustered around the [ 1010] pole, the pole of the basal plane being at least 60 deg from the specimen axis. Crystals grown at lower rates of zone travel showed the same orientation range, Fig. 1. This orientation is similar to that for other hexagonal metals grown from the melt, which is a little surprising when the mode of formation of the hexagonal phase is considered. The preferred orientation is probably caused by anisotropy of heat conduction, i.e., that crystal which can most effectively conduct heat away from the transformation interface will be favored. Fig. 2 shows the area on a standard cubic stereo-gram in which there are no poles more than 60 deg from one of the four < 111> directions. This area

Jan 1, 1962