Search Documents

By W. V. Bluck, W. L. McMorris

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most power plants is now going beyond buying at the lowest delivered fuel cost. It is now taking into consideration other factors, such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1986

By Edgar R. Kendall

A KNOWLEDGE of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. LOCATING THE SUPPLY The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1939

By G. W. Doepel, W. P. Sibley

A three-dimensional, multilayer, mathematical model has been developed for predicting performance by mis-c.ible displacement. Areal and vertical coverage, total gas-oil ratio, propane-oil ratio and oil-recovery factor for the multilayer system are computed as functions of hydrocarbon pore volumes of solvent injected. The technique has been programed for use on the IBM-7090 digital computer and was used in calculating perfortnance for continuous miscible displacement of a five-spot, 50-layer .system. Results reported are based on the use of published laboratory data for a single, uniform five-spot layer. However, the technique is sufficiently generalized to calculate performance of any system of layers of any pattern configuration and mobility ratio, provided data are available to describe perfortilance of a single layer. The technique has also been adapted for predicting oil recovery resulting from various gas-driven slug sizes. The results presented for both continuous and slug-type injection show, that permeability variation has 0 significant effect on oil recovery but that solvent composition, within the range studied, has a lesser effect on oil recovery. INTRODUCTION Experience from many of the miscible-phase displacement projects currently in operation indicates that the injected solvent flows preferentially through the more permeable zones in the reservoir. This preferential solvent flow in the high-permeability streaks results in a reduction of vertical coverage (C,) and an attendant decrease in oil recovery. The multilayer technique presented in this paper uses areal coverage (C.,) data for a single layer from the literature and from laboratory measurements of displacement efficiency (herein referred to as microscopic coverage, C,,) to calculate areal coverage (C,) and vertical coverage (C,) for the multilayer system. Oil recovery for the multilayer system is obtained as the product of (Ca) (Cm) (Cv). It is assumed that C, in a single layer is 100 per cent; therefore, (C,) (Cm) is a measure of oil recovery from that layer. Data presented in the literature for a single layer generally deal only with areal coverage and/or microscopic coverage —but seldom specifically with oil recovery. Nevertheless, this technique is flexible in that either Ca and C,, of an individual layer or a direct measurement of oil recovery for the layer may be used. In developing this technique, the problem arose concerning a method of determining the relative amounts of solvent that will enter each layer during any increment of solvent injected. To solve the problem, a dimensionless equation was derived for expressing solvent injected into each layer as a fraction of total injection. A finite-difference method was applied in integrating the equation to determine oil recovery for the system of layers as a function of pore volumes injected. The technique subsequently was programed for solution on a digital computer. The method was applied to predict performance of a deep California reservoir under continuous miscible displacement and has been extended for calculating oil recovery as a function of slug size for gas-driven slug injection. The technique may be applied to any petroleum reservoir that can be adequately represented as a layered system, by considering permeability variation,1-3 permeability range and average permeability. Each layer is then assigned its appropriate permeability, porosity and hydrocarbon saturation. RESERVOIR VOLUME CONTACTED BY SOLVENT It has been recognized for some time that high microscopic coverage (C,) can be obtained by injecting a miscible agent, such as propane, into an oil reservoir. These high values of C,,, have been demonstrated in the laboratory and are normally between 80 and 100 per cent, depending on solvent and reservoir oil composition as well as on reservoir temperature and pressure. In miscible-phase displacement, because there is no interface between solvent and oil, effective permeability to solvent is the same as that to oil. (This assumes that oil saturation has not changed and that water is immobile.) Consequently, mobility ratio (M) simply reduces to that of viscosity ratio . Perrine4 and Habermann5 have shown that large

"Quiet, please!" is the newest directive being thrust at industry by guardians of the environment-with good reason. In countless cases, industrial noise is literally deafening its listeners, and sooner or later the volume must be turned down. Noise control is already mandatory for many companies under a Federal regulation that went on the books when the Walsh-Healey Act was revised last May 20. The new rules impose specific noise limits on any plants supplying the Government with goods under a contract valued at more than $10,000.

Jan 1, 1970

By Barton K. Cross, Ronald J. Sparks

The question of' providing training for miners in the United States has been answered by Public Law 95-164, which stipulates not only that the mine operator will provide training, but generally how much and what material will be covered. At an operation employing 500 miners, the eight-hour refresher training requirement will necessitate an annual investment of over two man-years in labor, a figure that does not include the time spent in training new hires and job transfers. Such an investment can and should be cost effective, while catering to miners' needs.

Jan 6, 1979

By Oswald J. Heinrich

THE great improvements which have been made in late years in the different systems and instruments used to perforate the crust of the earth for purposes of testing and exploring for mineral resources or for other reasons, by means of bore-holes of greater or less diameter and to greater or less depths, are manifold. It may therefore be of interest to make an impartial comparison of them, or of such as are most commonly used. Being well aware of the difficulties which are encountered in such a task, a reasonable allowance must be made in such a comparison. It is a rare instance when even two decidedly different systems or instruments have been used in the same locality, penetrating identically the same strata to the same depth. The diameter of a borehole as well as its greater or less depth must also be considered in regard to its cost per foot, etc. But for practical purposes, for ex¬ploration at least, we may assert this rule Any borehole, of whatever diameter, which allows the means of examining the strata most carefully and completely, will be sufficient for this purpose, but that one which will do it most economically and in the least space of time, must be considered the best for it. It will, therefore, partially depend upon circumstances, what system, in spite of other superiorities, may be the best in each case, and the following remarks may aid in deciding this question. To make the attempt here to review all that has been published upon the different systems and means of boring would be out of place. Reference can be had to the able publications treating upon this subject. A difference in this respect exists in regard to the use of the hollow rods in connection with the diamond drill, used for that purpose. The great future, which appears to be evident for this instrument, will be warrant enough for any one, who has had the opportunity to test it, to give his experience to the public. Only in this way can we bring this system to such perfection, as it seems to deserve and * The drawings illustrating this paper are one-half the size of the tools represented, with the exception of the instrument used to reverse the current in the bore-hole (Fig. 17), which is one-third the actual size.

Jan 1, 1874

By J. J. Knoerzer

A full-scale operational test was conducted on the Coaltek preheating and pipeline charging system at the Semet-Solvay Div. of Allied Chemical at Ironton, Ohio, for the purpose of determining whether a high-quality blast furnace coke could be made from blends containing at least 75% Illinois No. 6 Coal and at the same time reduce air pollution during the charging of the ovens. The coke produced had similar physical characteristics as compared to our conventional wet-charged coke, with the exception of smaller size for the preheat coke. Air pollution during charging was con- trolled and there were no serious operating problems. The coking time was reduced 25% from our normal 17 hr for wet charging to 12.8 hr for preheated charges. The blast furnace performance with preheat coke was satisfactory.

Jan 1, 1976

By E. P. Mathewson

The early development of the reverberatory furnace for smelting copper-ores was the work of the Welsh smelters, particularly those of Swansea. The first record of a reverberatory furnace is made by Jars, who states that in 1755 copper-smelting was effected .in reverberatory furnaces at Middleton-Tyas, in Yorkshire, England. The first patent, of any importance, for improvements in reverberatory furnaces was granted to Thomas Williams in 1778 for the granulation of the regulus. The next was that of William Evetts, in Sheffield, in 1812, for the cooling of the fire-bridge by the admission of air. Charge-hoppers above the furnaces were in common use in 1848. The size of the hearth of the furnaces about the beginning of the 19th century was commonly 11 by 8 feet. No material development was made until the Welsh process mas brought to Colorado, where Richard Pearce, as manager of the Argo works, near Denver, developed the furnace to meet the requirements of a custom plant, under keen competition with lead-silver smelting-plants, using blast-furnaces. His improvements are outlined in Fig. 1, elaborated by permission from E. D. Peters's excellent work,' to which the reader is referred for further details. This figure shows that the furiiaces were in 1878, 9 ft. 8 in. by 15 ft. in hearth; and in 1894, 16 by 35 ft., while the capacity of the furnace had been increased from 12 tons per 24 hr. to 50 tons in the same period.

Jan 1, 1913

By H. Hooykaas

A few years ago Marsal published a method of predicting oil recovery as a function of time for an edge-water-drive reservoir with several rows of wells.' The method is based solely on oil- and water-production data obtained during a short period for the first row of wells and the gross productions (past and future) of all wells. This paper presents a streamlined version of the original publication and experimental evidence showing the reliability of this version. For this purpose scaled experirnents were performed in a large model (750 X 500 X 23 cm, 24.4 ft X 16.2 ft X 8.9 in.) in which edge-water-drive reservoirs with three rows of production wells were simulated. From the results of the experiments it is concluded that the method gives a fairly accurate prediction of the future production behavior of the reservoir and enables us to select the most profitable production plan. Results obtained with the method were always slightly conservative. INTRODUCTION The calculation method developed by Marsal aims at forecasting future reservoir behavior.' It can be applied to floods in which a number of down-dip wells are rapidly going to water. Essentially it is a method for predicting the future behavior of the up-structure wells on the basis of the observed behavior of the down-structure wells. As such, the method is especially useful for predicting behavior of edge-water drives toward several rows of wells. The requirement to be met for justifying the approach is identity of production mechanism in all regions of the reservoir. The attraction of the method then lies in the fact that it applies even when we have no complete description of the prevailing production mechanism. The original publication was in the German language and for this reason, perhaps, did not attract widespread attention. In our opinion it deserves to do so because it does offer in a simple way results which are in fair agreement with observed data. The aim of the present paper is to bring the method to the attention of a wider audience. The method in its most simplified form is reviewed and experimental data in support of it are presented. PRINCIPLES To show Marsal's principle. we will first write the continuity equation for very simple conditions, linear flow (in the positive x-direction) in an incompressible porous body [cross-section A(x), porosity +(x)], saturated with incompressible fluids (oil saturation S). When the oil in this formation is displaced by water, injected at x = 0 (inlet face), we get where q(t) is the total gross displacement rate and f the fractional oil flow. The equation can be solved if we make the assumptions: (1 ) that the fractional oil flow (f) is a univalent function of saturation (S); and (2) that the function is the same throughout the porous medium. Then: f = f(S) Solving this equation with the method of characteristics, we obtain

Jan 1, 1966

By James J. Bean

Although determining and controlling specific gravity of operating medium in a heavy-media plant manually presents no problem, there are advantages to automatic recording and control. The two installations discussed employ the usual method of measurement. Pneumatic control with band control and reset features is used to regulate dilution water and hence specific gravity. Difficulties have been mechanical in nature and associated with obtaining a proper I sample and maintaining tight air connections in bubble-tube piping:

Jan 1, 1950

By J. A. MacLellan, John C. Bowling, J. R. Davenport, G. M. Ellis

Six months out of the year the cold is always there, and it seems to be waiting for someone to make a mistake. The simplest things can shut down a multi-million dollar plant besieged with -40°F temperatures and a 40 mph wind. It takes only one man-door improperly latched to feeze up all the pumps on the bottom floor. Someone can poke a one inch hole in an outside wall in July and six months later, the whole plant is flooded because the main water line just froze up and burst. Some important things must be remembered in plant design for cold and remote areas. For one thing, everything in these areas is more expensive due to long and difficult supply lines. Fuel is expensive and would be a major cost item even if it were not expensive, due to the extended periods of low temperatures. Building volumes should therefore be kept to an acceptable minimum. Service areas, on the other hand, must be adequate, because maintenance generally has to be conducted inside in a heated area. Supply vehicles, for instance, have to get completely inside the building to unload. If you try to unload a supply vehicle with the door open at -50°F, you won't be able to find the vehicle for fog and if you take more than 5 minutes half the water lines in the plant will freeze UP.

Jan 1, 1972

By G. W. Tracy, R. D. Carter

A method based on an approach by Hurst' is developed for calculating water influx behavior. Using this method, superposition calculations may be eliminated. The principal diflerence between this method and that of Hurst is that, over finite intervals of time, constant oil-productton rates are assumed by Hurst whereas constant water influx rates are assumed in the presently described method. By adopting the assumption of constant water influx rate for finite time periods, a method is developed for calculating water influx behavior which lends itself to convenient combination with the material balance equation in the Schilthuis form. Above the bubble point, an equation is given for the explicit step-wise calculation of pressure history for a prescribed oil-production history. Use of this method of calculating water influx behavior should result in a considerable saving of time as compared to superposition calculations when the calculations must be made without using a digital computer. The connection is shown between the method described herein and the method developed by van Ever-dingen and Hursr2 (which requires superposition cal-culations). Also, results obtained using the two methods are compared.

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-clay to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands and slimes : The so-called concentrators and vanners, on the one hand, and the buddies and round tables on the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913

By G. B. Gibbs

Various semiempirical equations which relate defect-formation energies and entropies with elastic and thermal properties of a metal crystal are shown to be related by a simple model for lattice energy. An illustrative comparison of theory with experiment is made using self-diffilsion data for fee metals. SEVERAL workers have related the free energy of defect formation with elastic and thermal properties of a crystal lattice, particularly elastic bulk modulus and Debye temperature. The present note shows how the various approaches are related by a simple model for lattice energy. A comparison of theory with experiment is given using the self-diffusion parameters of fee metals. 1) A MODEL OF THE CRYSTAL LATTICE The internal energy per atom in a metallic lattice may be written U=Ui-Ue [1] where Ui and Ue refer to ion-ion interaction and valence electron energies, respectively. The volume per atom V has an equilibrium value 52 for which

Jan 1, 1968

John Langton, New York, N. Y. (communication to the Secretary*):—In Mr. Firmstone's discussion (Trans., xli., 912) the formula he gives for the periodical payment—his equation (2)—may be simplified in form. The expression given by Mr. Firmstone is : q=S(l+ r) 1-(1+r)-(1+r) r which is a simpler form to use in calculations. Where S= principal to bc extinguished. Q = periodical payment or charge for sinking-fund, r = rate of interest per period (i. e., interest on $1 per period). n = number of payments or periods. Kent's Mechanical Enyineer's Pocket Book, under the heading Annuities, equation No. 5, gives : " The annuity which $1 will purchase for any number of ytlars n is * Received Jiily 16, 1911.

Jan 1, 1912

By Lewis Reeve

As. part of a program of investigation of the properties of electric arc welds carried out in the laboratories of the A. 0. Smith Corporation, considerable work has been done on the determination of the oxygen, nitrogen and hydrogen content of different types of weld metal, employing for this purpose the so-called "vacuum fusion method." It is the purpose of this paper to describe certain improvements that have been introduced in this method of determining the gas content of metals, with particular references to the steel specimens examined in this investigation. The method and apparatus used at the beginning of the investigation were essentially those of the Bureau of Standards as described by Vacher and Jordan.1 Later a number of changes were introduced which resulted in. more rapid evacuation of the graphite crucibles employed and which enabled larger volumes of gas to be dealt with than could be handled conveniently in the Bureau of Standards equipment. In addition, the analyzing of the gases evolved from a melt in the same apparatus as collected was abandoned in favor of analysis outside the equipment using standard methods of gas analysis. The time required for gas analysis in the apparatus itself, as described by the Bureau of Standards, was found to be considerable, and during this time the rest of the equip-ment was tied up, preventing its use for the analysis of further steel sam-ples. As a result of the modifications introduced, the time required for the analysis of a steel sample for gas content was reduced from about 8 hours to less than 3 hours. Subsequently, the whole procedure of melting the sample and collect-ing the gases evolved was modified so as to enable a distinction to be drawn between the easily reducible oxides such as iron oxide and the more stable oxides such as silica and alumina. At the same time evidence was obtained indicating the probable existence in the steels of other nitrides than those of iron alone and making possible their quantitative determination.

Jan 1, 1933

By K. J. Brondyke, P. D. Hess

Lack of correlation between densities of aluminum alloy samples solidified under reduced pressure (vacuum gas test) and hydrogen content of the metal is explained on the basis of inclusions serving as nuclei for hydrogen bubble formation. As a result of these findings, the vacuum gas test is suggested as a practical tool to indicate metal cleanliness and the potential effects of hydrogen. Visual obseroation of the sample during solidification under vacuum provides more useful information than that obtained either from density meas -urements or sectioning of the solidified sample. A rapid, practical method of detecting and measuring gas in molten-aluminum alloys has been sought for many years. The development of the vacuum gas test appeared to solve this problem. However, the vacuum gas test is subject to certain limitations, and the results must be interpreted mindful of these limitations, as described herein. Since the only gas which is appreciably soluble in aluminum is hydrogen, the terms gas and hydrogen will be used interchangeably in this paper. In the early days of the aluminum industry, when techniques were not as refined as they are today, it was customary to pour small "pancakes" of alumi- num on a metal plate. These were allowed to solidify under atmospheric pressure. Excessive gas in the metal was evidenced by the appearance of small bubbles on the surface of the "pancake".' It is obvious that such a method would only show very high gas levels far above any which could be tolerated by today's standards of quality required for most applications. Various attempts were made to develop methods which would be more sensitive. Among these were measurements of density of aluminum alloys solidified under controlled conditions, radiography of cast slabs, and examination of fractures. The method which showed the greatest promise and appeared most practical was the solidification of a sample of the molten aluminum alloy under vacuum. The samples so solidified are evaluated either by observation for bubble emission during solidification, by sectioning the solidified sample and examining for porosity, or by determining the density of the solidified sample. This test is known internationally as the Straube-Pfeiffer test or the reduced-pressure solidification test, but in America it is commonly referred to as the vacuum gas test2-' and will be so designated in this paper. The determination of density appeared an attractive and convenient means of providing a numerical rating for the samples. Attempts were made in some instances to correlate densities to hydrogen contents. Unfortunately, the visible loss of gas during solidification of samples with high gas contents precluded a correlation of vacuum gas test densities with the observed gas evolution. This led to Alcoa's use of two different pressures; 50 mm of

Jan 1, 1964

By G. Rowan, M. W. Clegg

Approximate analytical solutions for non-Darcy radial gas flow are derived for bounded and infinite reservoirs producing at either constant rate or constant pressure. These analytical solutions are compared with published results for non-Darcy flow obtained on digital and analogue computers, and the agreement is show to be very good. Some observations on the interpretation of gas well tests are made. INTRODUCTION The flow of gases in porous media is a problem that has been the subject of much study in recent years [l - 71 , and many methods have been proposed for solving the non-linear equations associated with it. The assumption that the flow satisfies Darcy's Law It has been observed, however, that the linear relationship between the flow rate and pressure gradient is only approximately valid even at low flow rates, and that as the flow rate increases the deviations from linearity also increase. It has been suggested by a number of authors that Darcy's Law should be replaced by a quadratic flow law of the form This form of equation was first suggested by Forchheimer [9] and, later, Katz and Cornell [10], and Irmay [lll, developed a similar equation. Houpeurt [12] derived this form of equation using the concept of an idealised pore system in which each channel consists of sequences of truncated cones giving rise to successive restrictive orifices along the channel. This type of representation leads to a quadratic flow law of type [4], for all fluids, but it is found that the quadratic term is only significant in the case of gas flow. The methods of Houpeurt for solving gas flow problems will be discussed further in another section of this paper. Solutions of the non-linear equation for Darcy gas flow 121 may be classified as either computer (digital and analogue), or approximate analytical ones. The former include the well-known solutions of Bruce et al. [13], and Aronofsky and Jenkins [14] , but the latter solutions, apart from the simple linearisation of equation (2) to yield a diffusion equation in p2 , are not so well-known. Amongst these approximate analytical solutions should be mentioned the work of Barenblatt [IS], who has applied the techniques of dimensional analysis to obtain similarity solution to a large class of non-linear equations; also, a number of Russian authors, including Barenblatt [16] , Kim [17] and others, who have used the method of moments for obtain-

Jan 1, 1965

By J. S. Aronofsky, A. S. Lee

Results and experimental procedures are presented covering a preliminary laboratory investigation of the compaction of reservoir rocks and its effect on porosity and permeability. "Egective" compressibility was measured by subjecting core material to an overburden load and reducing pore pressure. Preliminary results showed relatively high effective compressibilities which varied from 1.8 X 10-' pore volume/pore volume /lb / in.~ for limestones to 7.7 X 10-6 pore volume/pore volume/lb/in.' and even higher for sandstone reservoirs conmining large amounts of fine clay material. It appeared from the initiol results that the effective compressibility of the material could not be correlated directly with porosity and that other factors, such as the amount of clay material present might have to be taken into account. The work to date has indicated that effective compressibility factors will have to be measured for the particular reservoirs heing studied. Oil permeability of core materid was measured under various effective overburden loads from 0 to 8,000 psi. It has been found than reduction of permeability in clean sands was relatively small and the results agreed with published data. For sandstones containing large amounts of clay, preliminary tests indicated very large reductions in permeability with increasing effective overburden pressures. It is planned to continue laboratory work on this phase because of its importance in low-permeability reservoirs. INTRODUCTION During the past few years increasing interest has been shown in the differences obtained between conventional laboratory measurements on cores at atmospheric pressure and those when reservoir conditions are simulated. Since these data are used as the basis for calculations and the prediction of reservoir behavior, their evaluation under reservoir conditions is most important. The effect of the compressibility of the rock upon the reservoir behavior, as fluid pressure declines, is an important subject which has been insufficiently studied. The total pressure on any plane through a reservoir is the result of the grain-to-grain rock pressure due to the overburden and the pressure of the interstitial fluid on the plane. As reservoir fluid pressure declines, the net load on the rock phase must increase, and the result is the compaction of the rock structure which produces a decrease in pore volume. Simultaneously, the rock grains expand into the pore space as the fluid pressure declines. The result of these two effects is defined as the effective compressibility of the rock and is expressed in units of pore volume/original pore volume/psi. Work was started by Imperial in 1954 on the effects of pressure on the porosity of reservoir rock. These studies established effective compressibility factors for some limestones and dolomites. Since that time effective compressibilities have been obtained for other Canadian and some U. S. reservoir rocks. In conjunction with the study of porosity, an investigation has also been initiated to determine the effects of pressure on permeability. One outcrop and several reservoir sandstone cores have been tested to date. ROCK COMPRESSIBILITY Apparatus anD Procedure A diagram of the apparatus used in these studies is shown in Fig. 1. The equipment was constructed so that a uniform pressure, equivalent to the reservoir overburden, could be applied by the oil pump and transmitted on all sides of the core through the Lucite sheath. The sample was completely saturated by circulating brine through the mounted core. Pressure in

By Comfort Adams

WHEN this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. The then chairman of the Engineering Division of the National Research Council, Doctor Howe, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority' of the members of the committee. To that end, the Engineering Division appointed-a committee, consisting of the gentlemen whose names follow, to mention only those who retained their connection with it. At, this time there were serious difficulties in the manufacture for the Government, of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted.

Jan 1, 1922