Search Documents

By Geo. T. Lynch

PALEOLITHIC MAN, laboriously shaping a stone implement in his cave, discovered that the dust irritated his eyes and nostrils and hindered his labors, whereupon, muttering a few incantations, forerunners of modern profanity, he removed himself and his work outside. There, ignoring the jeers of the hairy ?old-timers,? he turned his back to the wind and resumed operations in comparative comfort. Thus originated the dust problem in the mineral industries, and its solution. Despite long familiarity with the annoyance, danger, and loss occasioned by dust, little progress was made in the engineering solution of its problems until recent years. Some advance can now be reported but too many traces of ancient tradition and practice still remain. Considerable published information is available but only a part of this is of proved accuracy and utility. The greater portion is either misleading, being derived from too few cases to be of general application, or entirely erroneous, originating in guesswork, legend, or individual inspiration, divine or otherwise. The engineer, confronted with a dust problem, has neither the time nor the special training required to extract the values from this mass of low-grade. It is, therefore, desirable that we attempt to correlate the known values and to put them into a form upon which actual progress can be based. This discussion is, then, for the benefit of that engineer, particularly the engineer in the mineral industries and more particularly in ore-dressing plants, and is merely a gathering of facts already known but difficult to segregate.

Jan 1, 1938

By William Kent

Mr. ASHBURNER's paper on the Classification and Composition of Pennsylvania Anthracites, read at this meeting, well shows the need of new and accurate determinations of the heating value of these coals. A similar need exists for the determination of the value of bituminous coals, since the variation in quality of the latter is greater than the variation in anthracites. The recent extensive use of liquid and gaseous fuels, " patent" fuels, tan-bark, and other refuse fuels, also makes a necessity fix some correct method of determining the relative values of each of these fuels. Mr. Ashburner has recommended that tests of coals should be undertaken by the Second Geological Survey of Pennsylvania, and Professor Dewey, as stated in Mr. Ashbnrner's paper, has suggested a plan for tests of American coals, by the Smithsonian Institution, for which an appropriation by Congress will be asked. It is to be hoped that if any extensive series of tests of coals is carried on under either Government or State auspices, the erroneous methods of test which were followed by Professor Johnson in 1842, and by Quartermaster-General Meigs in 1882, will not be adopted.* The first requisite in determining the heating-power of a fuel is proper apparatus, such as has not been used in any of the tests of American coals yet reported. In the hope that more accurate means may be used in future tests, the writer desires to call attention to an apparatus which he has designed for the purpose. Not having had opportunity for making a trial of it, nor even of having it criticised by others, he does not offer it as the best possible apparatus; but if it contains any points of value, and leads to the design of still more suitable devices by others, the object of the presentation of this paper will be accomplished. The tests by Professor Johnson and General Meigs were made by evaporating water into steam in ordinary steam-boilers. A steamboiler of ordinary construction is not a good apparatus for determining the heating power of a fuel, for the following reasons:

Jan 1, 1886

By R. A. Esmonde

This paper describes the building and testing of a prototype welded aluminum truck body to a new design concept. The results of these tests are given along with an outline of further developments in the design and field application of aluminum bodies. The results of field service history are recorded with special reference to types of mining operations, service performance, wear, maintenance and economics of operation. Mention is made of current U.S. usage and predictions given as to future development of aluminum bodies in the mining industry. The use of aluminum for off-highway truck bodies in hauling rock for the mining and construction industries is by no means the novelty that it may seem. In 1932 an aluminum unit proved very satisfactory in service on the Hoover Dam project but at that time the only high strength aluminum alloys available were not weldable and with the high cost of construction, a sound economic case for an aluminum body could not be made. After World War I1 great advances in aluminum welding techniques, using the inert gas shield, combined with the development of high strength alloys with good welded properties and welding characteristics changed the whole picture. Welded aluminum bodies were rapidly developed and by 1958 attention was again focused on the use of aluminum for off-highway truck bodies. EARLY DEVELOPMENT WORK In 1959 Alcan, the Aluminum Co. of Canada, embarked on an extensive development program to prove the durability and economics of aluminum truck bodies for the mining and construction industries. The first step was to design a prototype aluminum body which took particular advantage of the fact that the modulus of aluminum is only one third that of steel. This means that within the elastic range, aluminum moves three times as much as steel which makes it more flexible and capable of absorbing much greater impact shocks. A body was built and mounted on a 22-ton truck and taken to the Jeffery Mine of Canadian Johns Manville Company at Asbestos, P.Q., Canada. Very little information was available as to the order of stresses that were set up in off-highway truck bodies and so it was therefore decided to carry out a test program to find out this information.

Jan 1, 1969

By R. E. Hobart

THE development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines; led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was a 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means, of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 2, 1918

By David Reger

ONLY a few small pools of oil were found in West Virginia during 1924. The price of oil was so low that there was no incentive for active effort toward the discovery of new pools or the exploitation of reasonably certain productive areas. At present, several encouraging edge-pool developments are being held in reserve in the hope that a more favorable market is not far distant. In the old pools, wells are being carefully tended; there being little tendency toward abandonment. even in cases where production is temporarily unprofitable. In natural gas, however, the total value of which at the well mouth is now more than that of oil, the year has been busy and profitable. , The decline of old pools, together with the increasing demand, has caused the large operators who carry their gas to the consumer to make great efforts to preserve or increase the rate of production; while the small operators, who sell their product to the large companies at the well mouth, have been stimulated toward the same effort by more favorable prices. These conditions brought about the completion of a greater number .of gas wells in 1924 than in 1923. Few pools of gas have been discovered during the year, the principal production having been obtained in old areas and in the unusually large new territory that was revealed as potentially productive by the drilling of 1923. Some of these latter areas are still without pipelines but definite plans for getting most of this gas are now being executed.

Jan 3, 1925

By F. C. Bond

Since the Third Theory of Comminution was presented eight years ago (I) it has found increasing use in crushing and grinding problems. The practical utility of its wok index equation is quite generally acknowledged (2). However, its theoretical basis has been questioned in at least three technical articles (3) (4) ('). The purpose of this paper is to present experimental proof that it is scientifically correct. Particles under compressive stress are strained and deformed. They absorb strain energy, and when this locally exceeds the breaking strength, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends and splits the rock, releasing the strain energy as heat. The initial energy flow causes additional crack tips in highly strained areas. If the compression is rapidly applied by impact, crack tips may form before the strain energy has reached equilibrium in the particle, thus decreasing the total work input required for breakage. The energy necessary to break is essentially the energy necessary to produce crack tips, since the energy necessary to extend the cracks to breakage is already present as strain energy in the deformed particles. After breakage nearly all of this energy appears as heat. The crack length cannot be measured directly. However, in particles of regular and similar shape the crack tip length is considered as equal to the crack depth, or crack extension necessary to break, so that the crack length equals the square root of one-half of the surface area. The Third Theory states that the useful work done in crushing and grinding is directly proportional to the total length of the new cracks formed. It can be confirmed by showing that a constant work input produces a constant length of new cracks when reducing the same material to different product sizes. This is done in the present paper on a wide variety of material. The constant work input was supplied by one revolution of the 12" x 12" laboratory ball mill used in making grindability tests by the Allis-Chalmers method (12) (13) The new crack lengths produced per mill revolution were measured from all available grindability test results at 28, 35, 48, 65, and 100 mesh on fifteen different ores, and were found to remain substantially constant for each ore at all mesh sizes. A new technique is used for the measurement of crack lengths. Size distribution plots of the mill feed and product are made by the Third Theory method (9) and the crack lengths are obtained from these plots by the procedure described in the present paper. The energy input required to produce a unit length is of fundamental importance in the size reduction of brittle solids. The crack length Cr is expressed in centimeters per cubic centimeter of solid material. It bears a definite relationship to the external surface area of the crushed or ground solid. A uniform particle shape must be assumed before the surface area and crack length can be evaluated. In this paper it is assumed that the relationship between the surface area and the particle volume of a particle d microns in diameter is the same as that of cube d microns on a side. The external surface areas of particles with a cubical breakage probably agree approximately with this rule, and correction factors can be applied when physical measurements of the surface areas are available for comparison. However, the assumption of equivalent cubes has been found satisfactory for most calculation purposes. Assuming equivalent cubes, one cubic centimeter of particles d microns in diameter will have a crack length Cr of v30.000/d centimeters, and a surface area of 60,000/d square centimeters. The specific crack length is thus equal to the square root of one-half the specific surface area. Where Sa is the surface area in square centimeters per gram and Sg is the specific gravity of the ground solid, then Cr = vSg . Sa/2 = 173.2/ vd (1)

Jan 1, 1961

By J. J. Thomas

THIS investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. FIG. 1.-STRESS-STRAIN DIAGRAM. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 2, 1921

By S. W. Farnum

ABOUT three years ago at a coal mining institute meeting, it was predicted that mechanical load-ing underground would progress faster than either the electric coal-cutting machines or electric loco-motives had in previous years. This prediction has proved correct so far. In 1925 over 6,000,000 tons of,coal was loaded mechanically underground in the United States and it is estimated that the 1926 tonnage will reach 10,000,000. The use of electric mining machines and locomotives .has prepared the way for quick results. Most coal mines are now equipped with electric power and have a competent staff who understands its use. In spite of this advantage the introduction of the loading machines brings many new problems. Im-proved and concentrated transportation; doing the drilling, shooting, tracklaying and face timbering with company men instead of the former tonnage men; doing the work on the new basis in an economical and efficient manner; altering or modifying mining systems where necessary to further improve the work and reduce oper-ating costs; improving the percentage of lump coal and reducing the slack content where desirable; improving the cleaning of the coal and obtaining a more dependable .and uniform output are a few of the problems that must be met. Each of the different types of loaders now on the market has its particular advantages and disadvantages for a given mining condition. Even with the same mining conditions one type will work well under one ;system of handling, whereas another may favor another system or mining method.

Jan 5, 1927

By W. J. Parton

D. R. MITCHELL*—The Chairman mentioned that we have had many papers on cleaning of fine coal and treatment of wash water solids. There are, of course, two reasons for that. One is that we have legislation, particularly in the east. that is making us go into these things whether we want to or not. It just so happens at the present time that I have four plants that are going up under my general direction, three new and one rehabilitation job, and in all of them, we have these problems. Therefore, I was very happy to be able to listen to these papers, because some of the things that are in them are going to help me solve some of the problems that I am facing. Of course, the second reason why we are concerned about fine coal recovery is the fact that coal has become a luxury item in a good many places, particularly in the anthracite region, so that we cannot afford to have it go to waste like we did in former years. There is a third minor reason, and that is that we are finding how to handle and use the extremely fine sizes that we did not know how to use in former years. Now, I have a couple of questions that I would like to ask. First, what are the maximum solids that you could have in a pulp going to one of these launder screens? I realize that it would be for anthracite. Second, of course the life of these screen surfaces is not very long— with brass or bronze, I believe it is a week, and with stainless steel, a month. Would it be possible to use screen surfaces like the Bixby-Zimmer round rod for the small sizes and possibly increase the life? Have you experimented with that? Another point that I would like to bring out, both in Mr. Parton's paper and in some of the others, in studying cyclones and any settling apparatus where we use orifices, the life of the orifices is very short, and that is a problem that still has to be solved. The capacity of the cyclone seems to be small, and if you have a bat-

Jan 1, 1950

By John L. Lamont, Walter Crafts

ADEQUATE hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test1 and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversion3 from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollenback,5 Burns, Moore, and Archer,6 and Burns and Riegel.7 The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependent only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1945

By William Bent

MORE than twelve years were spent by Wöhler at the instance of the Prussian Government in experimenting upon the resistance of iron and steel to repeated stresses. The results of his experiments are expressed in what is known as Wöhler's law, which is given in the following words in Du Bois's translation of Weyrauch :* "Rupture may be caused not only by a steady load which exceeds the carrying strength, but also by repeated applications of stresses, none of which are equal to the carrying strength. The differences of these stresses are measures of the disturbance of continuity, in so far as by their increase the minimum stress which is still necessary for rupture diminishes." A practical illustration of the meaning of the first portion of this law may be given thus : If 50,000 pounds once applied will just break a bar of iron or steel, a stress very much less than 50,000 pounds will break it if sufficiently often repeated. This is fully confirmed by the experiments of Fairbairn and Spangenberg, us well as by those of Wöhler; and, as is remarked by Weyrauch, it may be considered as a long-known result of common experience. It partially accounts for what Mr. Holley has called the "intrinsically ridiculous factor of safety of six." Another "long-known result of experience "-although this has not, as the writer believes, been investigated by scientific experimenters-is the fact that rupture may be caused by a succession of shocks or impacts, none of which alone would be sufficient to cause it. Wrought iron will crystallize by repeated blows in service and become weaker than cast iron. Iron axles, the piston-rods of steam-hammers, and other pieces of metal subject to continuously repeated shocks invariably break after a certain length of service. They have a " life" which is limited. Iron rods in bridges sometimes crystallize and break, although the rods in most of our iron bridges * Strength and Determination of Dimensions of Structures. By Dr. J. J. Weyrauch. Translated by Du Bois, New York, 1877.

Jan 1, 1880

By H. DeWitt Smith

THE disastrous effect of two major wars on foreign economic health is giving American capital opportunities which might have not otherwise developed. At a time when discovery of major orebodies in the United States awaits fuller application of new geophysical tools and technical methods, U. S. investors must seek other fields where investment may be put to work. The unsettling effects of war have made it almost impossible for foreign nationals to develop mineral wealth, permitting Americans to enter at a time when U. S. mining, with a few exceptions, is in the process of expanding known orebodies and developing only a few new ones. Available capital, however, is not the only pre- requisite for entering the foreign mineral development field. The capital must be able to work in favorable economic atmosphere, a condition not easily satisfied in a world constantly in a state of political and social flux. In many countries, the political theory changes as often as the wind direction in March. Thus, the political stability of the form of government is of prime importance to the investor. In addition, a balanced budget and a moderate tax structure are important. Because in making foreign investment it is inevitable that one will have dealings with government officials, it is basic that they must be of high integrity. In countries filling the requirements, it will usually be found that the economic initiative of the individual is respected. Newmont Mining Corp.'s three major investments in the last 15 years have been in Canada and the

Jan 1, 1952

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By W. O. Philbrook, A. H. Jolly, T. R. Henry

IN the course of a study of slag-control methods, the authors devised a laboratory technique by which the basicity of basic open-hearth furnace slap could be estimated with sufficient accuracy to make the method of possible interest for slag-control purposes. The process consisted of measuring the slight basicity of an extract of the powdered slag in water. The procedure was presented, for the benefit of those who might care to experiment with it, in a paper submitted in the 1944 McKune Award Contest and presented at the 1944 Open-hearth Conference in Pittsburgh.1 Interest expressed at that meeting and favorable operating experience with the method at a neighboring plant, as described in a related paper by Michael Tenenbaum and C. C. Brown,2 have encouraged us to present further details of the development, technique, and pitfalls of the method and some additional data not included in our first report. At the outset it must be admitted that this method of estimation of slag basicity is not perfect; neither is any other that we know of. It is subject to somewhat greater errors than would be desirable, but compares favorably with other techniques in this respect. It has the disadvantage that it places the final determination of slag basicity in the hands of a laboratory technician rather than the furnace operator, although it can be operated in a control laboratory adjacent to the furnaces. It requires close attention to certain details, as do most laboratory procedures. On the favorable side, it eliminates the "human factor" of personal judgment inherent in estimation from pancakes or powdered samples. The procedure can be placed in practice much more rapidly and presents much less of a training problem than visual methods of estimation. The principle and operation of the method are so simple that it would not be surprising if others have experimented with the same or similar procedures, but we are not aware of any prior publication of details. Our own shop has been operating fairly successfully for several years with the aid of slag pancakes. Since the past year or two have not been favorable for the expenditure of time and energy where the need was not urgent, we have not introduced the new practice for actual slag control and hence do not have extensive operating data. In presenting this method, therefore, we make no claims as to theoretical justification nor guarantees as to practical applicability, but offer it as an empirical observation. We believe it has sufficient merit to warrant its investigation by those just instituting a slag-control program or in search of supplementary methods for judging slag basicity PRINCIPLE OF THE METHOD It is well known that when burnt lime or slaked lime is shaken up with water it

Jan 1, 1945

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By James Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with excavator mounted upon it, which has reached a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant combining a drag-line excavator on cater-pillar mounting and a gravel-washing plant on a floating barge. The most efficient ones use a bucket of 1 to 2 yd. capacity with boom from 40 to 70 ft. long. The barge varies from 20 by 30 ft. to 36 by 48, and carries the trommel screen, pump, riffle sluices and power engine.

Jan 1, 1936

By Manning W. Cox

Van Stone mine area is situated at the head of Onion Creek on the northwest flank of Gillette Mountain, Stevens County, Washington. The di strict was found during World War I, but the mine did not come into production until 1952. Production to the end of 1965 was 2,242,960 tons of ore that yielded 10,700 tons of lead concentrates and 120,000 tons of zinc concentrates. The area is part of the Selkirk Mountains Zinc-Lead Belt, or Kootenay Arc, extending from near Revelstoke, British Columbia, to Colville, Washington. A thick but incomplete section of Paleozoic marine formations occurs in the Kootenay Arc and is overlain by marine and continental Mesozoic formations. Both are invaded by Late Mesozoic-Tertiary batholiths. The belt is characterized by open complex folding and extensive high-angle and local thrust faulting. Principal ore deposits occur in the highly deformed carbonate rocks of Cambrian age-the Maitlen (Laib) and Metaline formations. The Van Stone mine occurs along a steeply S-shaped fold lying between the Kaniksu Batholith on the west and the Rogers Mountain Fault, a northeast-trending fault on the west flank of the Gillette Mountain Anticline, to the southeast. The fold is cut by northeasttrending faults containing notoriously irregular lamprophyric, diabasic, and pebble dikes. The host rocks, lower Paleozoic dolomites, are decolorized, silicified, and silicated in the mine area. Jasperoid and tremolite are the common alteration minerals. Other gangue minerals are barite, pyrite, brucite, calcite, and, near the batholith, pyrrhotite. Ore minerals are galena, jamesonite, and sphalerite. Ore minerals occur in bunches and pods intergrown with tremolite and jasperoid. Zinc is roughly eight times more abundant than lead. The highest ore outcrops at 3870 feet elevation, and an undeterminable portion has been removed by glacial scour. The lowest drill hole penetration has reached 3220 feet elevation. Oxidation ranges up to several hundred feet in depth and may be most closely related to pre-glacial groundwater circulation. The area of the mine was completely over-ridden by Pleistocene continental glaciers, and the present erosion surface is nearly continuously blanketed by up to 150 feet of glacial outwash.

Jan 1, 1968

By Portland P. Fox, Berlin C. Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. THE EQUIPMENT The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1938

By George R. Eadie

As 1972 slipped through our grasp, coal industry adjustments to health and safety laws, environmental restrictions, rising costs and higher production targets left many mine operators groping for a new grip. The industry adopted a defensive attitude in 1972 as it faced the onslaught of inspectors. With rigid demands for improving safety and instituting environmental programs, the industry worked hard and watched production figures stagger upward while operating costs zoomed. In an effort to determine how to meet the goals that were established for fewer ignitions, fewer accidents, less respirable dust, lower noise levels, fewer law violations, better reclamation, less pollution, lower costs and higher production, industry representatives attended numerous technical meetings.

Jan 2, 1973